vonado 10273 User manual

Haunted House # Lego Light Kit for 10273
Package contents：
1 x 15cm White Dot Light
4 x 15cm Warm White Dot Lights
1 x 15cm Red Dot Light
3 x 15cm Green Dot Lights
1 x 15cm Blue Dot Light
1 x 30cm White Dot Light
2 x White Strip Lights
6 x Green Strip Lights
3 x 5cm Connecting Cables
10 x 15cm Connecting Cables
1 x 50cm Connecting Cable
6 x 6-port Expansion Board
1 x 8-port Expansion Board
1 x AA Battery Pack
Extra pieces
Important things to note:
When installing dot lights
Make sure they are correctly placed (Yellow LED package is exposed). You can put they either
on the top of the studs or between studs.
Place wires on the surface or under the building blocks.
The wire can be place between the building blocks or under the block, but they should be
placed between the studs correctly.

Be careful when insering the micro connector to the micro expansion board. With connecting
cable side facing down, conenct the connector to the board as per below. In case of damaging
the pieces, do ont force to connect the pieces.
Insert the connectors to the ports.
Be careful when you are operating, there’s only one correct way to insert, make sure the
expansion board is upward, find the soldered “=” sign on the left of the port. When you
are inserting, the side which the wires can be seen should be faced to the “=” sign and
if you feel hard to insert, please stop, and don’t force it, for that may result in bent
pins inside the port or overheating of the expansion board.
At this point, use the tweezers to straighten the bent pins.

Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be
inserted only one way. With the Strip Light facing up, ensure the side of the connector
with the wires exposed is facing down. If a plug won’t fit easily into a port connector,
don’t force it. Doing so will damage the plug and the connector.
Finally, please pay attention to the positive and negative terminals of the battery
when installing the battery case.

Instructions for installing this kit：
OK, Let’s Begin! You can use the tweezer to help to install this lighting kit.
Separate the house as per below.
Remove the doll on front the door as per below.
Remove the lamp from the left of the door, disassemble it.

Take a white 15cm dot light, thread the connector through the yellow 1x1 round piece, pull
the cable out till the light is placed inside.
Reconnect the lamp shade and the post.

Reconnect the lamp.
Lift the following piece, thread the cable through the space as per below.
Close the space.

Remove the following rail, disassemble it.
Place the cable as per below, secure the cable with the following cone piece.
Reconnect the following 1x1 plate.

Remove the following bricks.
Place the cable as per below, reconnect the bricks to secure the cable.
Pull the cable out as per below.

Take a 6-port expansion board, connect the connecting cable to it.
Stick the expansion board to the back of the door with adhesive square.
Take a white 30cm dot light, repeat the steps above to install the light at the right side.

Remove the following bricks, place the cable as per below before connecting it to the
expansion board, reconnect the bricks to secure the cable.
Connect the cable to the expansion board.

Take a green strip light, a 15cm connecting cable, connect the connecting cable to the strip
light.
Stick the strip light over the door, thread the cable through the frame to the inside.

Wind the cable around the post before connecting it to the expansion board.
Take a 15cm connecting cable, connect it to the expansion board.
Thread the cable through the following place, pull it up.

Take a green strip light, connect the connecting cable to it.
Take a 15cm connecting cable, connect it to the strip light.
Stick the strip light to the following place inside the door.

Lift the following piece, thread the connecting cable from the strip light through the
following space as per below.
Close the space to secure the cable.
Remove the following skeleton, and the desk as per below.

Take a 6-port expansion board, connect the connecting cable to it.
Tuck excess cable before sticking the expansion board to the following place.
Take a 15cm green dot light, thread it through the following space.

Stick the light to the following place with adhesive square.
Disconnect the following brown 1x12 plate.
Wind the cable half around the following stud, reconnect the brown 1x12 plate to secure the
cable.

Connect the cable to the expansion board, tuck excess cable.
Take a 15cm connecting cable, connect it to the expansion board.
Remove the following trunk and the yellow piece.

Take a 6-port expansion board, connect the connecting cable to it.
Stick the expansion board to the following place with adhesive squares.
Reconnect the skeleton.

Remove the cobweb.
Take a green 15cm dot light, stick it to the following place with adhesive square.
Pull the cable up as per below.