Vornado flippi Series User manual

READ AND SAVE THESE IMPORTANT INSTRUCTIONS
Owner's Guide
LEA Y TENGA EN CUENTA ESTAS INSTRUCCIONES IMPORTANTES
Guía del Propietario
LIRE ET CONSERVER CES INSTRUCTIONS IMPORTANTES
Guide de L’utilisateur
www.vornado.com
™
models Flippi V10 and Flippi V

Designed, engineered and supported in Andover, Kansas.
Pensado, diseñado y respaldado en Andover, Kansas.
Conception, mise au point et soutien technique effectués à Andover, au Kansas.
Questions or comments?
¿Prequntas o comentarios?
Questions ou commentaires?
www.vornado.com
[email protected]
800.234.0604

English 3
Important Instructions ...................................................................................4
How To Use....................................................................................................9
Care and Maintenance.................................................................................11
Warranty.......................................................................................................12
Contents
Español p. 14
Français p. 26

4English
Your Vornado Air Circulator has a polarized plug. (One blade is wider than the other.)
To reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
The manufacturer assumes no responsibility for damage or injury caused by failure to
follow these instructions, improper product use, or unauthorized product modification.
Any such actions will invalidate the product warranty.
WARNING: Do not tamper with or modify this product in any way.
WARNING – To reduce the risk of fire or electrical shock, do not use this product with
any solid state speed control device. To reduce the risk of fire or electric shock and
injury to persons, do not use in a window.
WARNING – This is a fan - not a toy and not intended for children. To reduce the risk
of personal injury and electric shock, the Flippi ™ fan should not be used, operated or
placed where children can reach it.
This product employs overload protection (fuse). A blown fuse indicates an overload
or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace
the fuse as per the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded or returned to an authorized service facil-
ity for examination and/or repair.
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE.

English 5
Do unplug your circulator before cleaning.
Do clean your Vornado Air Circulator regularly. Refer to the CLEANING instructions
provided. Never clean the air circulator in any manner other than as instructed in this
manual.
Do use common sense when using this product and/or any electrical appliance.
Do use caution when positioning this product on an elevated surface, as vibrations
or accidental bumping may cause the fan to unexpectedly fall.
Do Not use gasoline, thinners, solvents, ammonias or other chemicals for cleaning.
Do Not immerse this product in water or allow water to drip into the motor housing.
Do Not use near furnaces, fireplaces, stoves or other high-temperature heat sources.
Do Not position this product too close to draperies because they may be drawn into
the rear grill, cutting off airflow.
Do Not use this product outdoors.
Do Not use this product on wet surfaces.
Do Not use this product in a bathtub or shower.
Do Not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
Do Not carry this product by the cord, or use the cord as a handle.
Do Not attempt to repair or replace parts.
Do Not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Arrange cord away from traffic area and where it will not be
tripped over.
Do Not operate the fan while closed in the nested position as it will not circulate the
air.
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE.

6English
User Servicing Instructions
Grasp plug and remove from the receptacle or other outlet device. Do not unplug by
pulling on cord. Open fuse cover (A.) by sliding access cover on top of attachment plug
towards blades. Remove fuse (B.) carefully by gently prying out the ends of the fuse
from the receptacle. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse. Contact
Vornado customer service for replacement fuse. Phone: [phone], email:
[email protected]
Install replacement fuse (C.) by first placing the end of the fuse into the fuse receptacle
which is opposite of the blades of the plug, then carefully push in the other end. Only
push against the metal end of the fuse, not the glass center portion. Close the fuse
access cover (D.) by sliding the cover back into the plug until it is completely closed,
latches and is flush with the face of the plug. Risk of fire. Do not replace attachment
plug. Contains a safety device (fuse, AFCI, LCDI) that should not be removed. Discard
product if the attachment plug is damaged.
The Flippi V (with remote) requires one (1) lithium coin cell battery (CR2032), 3 Volt
(included). DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR
LEAK.
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE.
A. B. C. D.

English 7
SAVE THESE INSTRUCTIONS
WARNING: KEEP BATTERIES AWAY FROM CHILDREN. If batteries are swallowed call
the National Poison Control Center at 1-800-222-1222 or 202-625-3333. In Canada call
416-813-5900.
Note: This equipment may generate, use and/or radiate radio frequency energy that
may cause harmful interference to radio communications. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to contact Vornado Consumer
Service at 1-800-234-0604.
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE.

8English
Trust.
It is said that trust isn’t given, but earned. For decades Vornado has been earning the
trust of our customers by offering them only the best. Vornado provides the highest
level of performance, coupled with the highest level of support available. Complete
satisfaction with no exceptions – this is Vornado’s promise to you. If you are not satis-
fied for any reason, please contact us. Knowledgeable representatives are available at
1-800-234-0604 from 7:00 AM to 6:00 PM CST. A wealth of additional support is also
available online at www.vornado.com. On behalf of myself and the entire staff at our
Andover, Kansas headquarters – thank you for selecting Vornado.
Sincerely,
Randy Brillhart
CEO, Vornado Air
Find our complete product line at www.vornado.com

English 9
How To Use
Flippi™ was engineered to provide just the right amount of air, either directed
at you to create a nice breeze, or away from you to create swirling currents of
air, rejuvenating your personal space.
A
Direct Airflow
The power head can be adjusted 180 degrees to
direct airflow where you need it. Or for an unobtrusive
look when not in use, the power head can be posi-
tioned down into the "nested" position. Do not oper-
ate the fan when in the nested position, as no air will
be circulated. Position Flippi away from objects that
may block airflow.
Flippi V10
The Flippi V10 has 3 speed settings. Set "I" for Low,
"II" for Medium and "III" for High. Turn dial to "O" to
power unit Off.
The Flippi V10 features oscillation for more airflow
possibilities. Oscillation can be turned On or Off with
the rocker switch located on the back of the unit.
Press (-) to turn oscillation On and (O) to turn oscilla-
tion Off.

10 English
How To Use
B
A
C
D
EF
Flippi V
Power (A) The unit functions ON and OFF by pressing the POWER button.
Lights on the unit’s control panel indicate the power is ON.
Fan Speed (B) The fan speed can be adjusted by pressing the POWER
button. Press the button to switch between the unit’s 3 speed settings. Lights
on the unit’s control panel indicate the selected speed setting.
Oscillation (C) Oscillation can be selected by pressing the Oscillation Button,
press again to switch OFF. Note: Oscillation only works when the main power
is ON.
Remote Control Requires a line-of-sight path to the blue lens on the front
of the base to allow for the signal to be received by the unit. To turn the unit