Voxx Electronics Prestige APSRS1Z User manual

128-9479
1 of 4
Model APSRS1Z
Owner’s Manual
PATENTED: www.voxxintl.com/company/patents
PRESTIGE
KEYLESS ENTRY
The button on the transmitter can be used to unlock the vehicle's doors, while
running under control of the remote start. Simply press and hold transmitter button
for 3 seconds as you approach the vehicle and the doors will unlock.
NOTE: Vehicle must have power door locks, and this option must be connected
at time of installation.
REMOTE CAR FINDER
The Start button is also used to access the car nder mode. This
feature is particularly useful in a crowded parking lot where nding
your car may be difcult. To access the car nder mode, while
within range of your car, simply press and hold the button of your
transmitter for three seconds. The parking lights will begin to ash
making your vehicle more visible. The lights will stop automatically
after 30 seconds. If you wish to turn off the car nder mode prior
to the expiration of the 30 second timer, press and release button
of your transmitter one time.
1 Channel Remote Car Starter
FEATURES
2 One Button Programmable RF Transmitters
One Channel Receiver (capable of accepting 4 transmitters)
External Superheterodyne Receiver Antenna w/Push Button Switch & LED
PBS / (-) Unlock Output
On-Board Start Relay
On-Board Accessory Relay
On-Board Ignition 1 Relay
On-Board Ignition 2 Relay
Ignition 2 Relay Selectable On or Off During Cranking
On-Board Parking Light Relay
Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
Tach Signal Learning Circuit
( + ) and ( - ) Safety Shutdown Circuits
Alarm By-Pass Output
Accessory Outputs (Pulse Before & After Start, During Crank & After Shut Down)
Selectable Steady or Flashing Parking Lights for Run Indication
Selectable 5, 10, 15, 20, 45 & 60 Minute Run Time
Selectable 1 Sec., 3.5 Sec., or 1 Sec./Dbl 1 Sec. Door Lock Output Pulse
Car Finder Mode

128-9479
2 of 4
2
REMOTE STARTING THE VEHICLE
This unit will not start the vehicle if any one of the following situations exist:
 The vehicle's hood lid is opened.
 The gear shift selector is not in Park.
 The brake pedal is depressed.
 The safety control switch is in the Off position.
1. To start the vehicle, press and release the Start button two times within
2 seconds. The vehicle will start and remain running for the pre-programmed
run cycle of up to 60 minutes. As a visual indication, the parking lights will ash
or remain on depending on the setting by your installation center.
2. When you arrive at the vehicle, turn the ignition key to the ON position (not the
spring loaded start position), then step on the brake pedal to disengage the
remote starter. The vehicle will continue to run, but now on its own power.
NOTE: The engine will stop running before the pre-programmed run cycle has
expired if you perform any one of the following functions:
- Press and release Key/Trunk button on the keychain transmitter two
times within 2 seconds
- Depress the brake pedal
- Open the vehicle's hood
- Place the unit in the safety override/disabled mode
PUSH BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL
SWITCH
The Push Button LED switch located in the receiver allows you to temporarily
disable the remote starting function of the system. This is recommended whenever
the vehicle is being serviced.
To place the system in the service mode:
1. With the system disarmed/unlocked, and the ignition switch off, Press and
Hold the Push Button, found on the windsheild receiver, in.
2. Turn the ignition switch on, off, on, off, on, off.
3. The LED begins to ash two short ashes followed by one long ash and
continues this pattern until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start
is in the service mode and will not start from RF or any other input Posse or
otherwise.
To Exit R/S Override Mode:
1. With the system disarmed, Press and Hold the Push Button, found on the
windsheild receiver, in.
2. Turn the ignition switch on, off, on, off, on, off.
3. The LED turns off, indicating that the R/S unit is fully functional once again.
NOTE: The LED on the receiver can be selected/toggled on and off. This feature
is useful if you do not want the LED ashing all the while the vehicle is locked.
To toggle this feature on or off:
1) Turn the ignition switch on then off.
2) Within 5 seconds, Press and hold the receiver's push-button switch for

128-9479
3 of 4
5 seconds. The LED will ash once for "ON" and twice for "OFF". On, means
normal ash patterns will function, and off normal ash patterns will not function.
The Programmed Transmitter Notication, will always function, as well, or the
programming mode of the unit for transmitters or feature selection.
PROGRAMMED TRANSMITTER NOTIFICATION (PTN)
Every time after Disarm, when the ignition key is turned on, the unit's LED will
report the number of transmitters programmed into the system. This safety
feature will alert you if an unauthorized transmitter has been programmed
into your vehicle's security system without your knowledge. Typically from the
factory, there will be 2 ashes and a pause, repeated 3 times, indicating that
two transmitters are programmed into the system. If you note additional ashes,
an additional transmitter may have been added without your knowledge or
authorization. If you notice a change in the transmitter LED report pattern, you
can correct this by looking up how to erase and reprogram your transmitters
found in the transmitter programming guide. This reprogram operation will erase
all unauthorized or unwanted transmitters.
PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1)
The Transmitter Model Name 171BP, is also found on the back of the transmitter
case. This transmitter uses a CR2032 Battery.
1. Turn the ignition key to the on position.
2. Press and Release the valet/programming switch 3 times
(Siren Chirps and lights ash).
3. Press the Button of each transmitter you want programmed until you hear a chirp
from the horn or siren, or the parking lights ash.
4. Turn the ignition switch off.
The above action programs the Start button in a 1 button system.
Transmitter Battery Replacement:
1. Locate the slot along side lower right side of the transmitter case and using a
plastic tool or a coin, separate the two transmitter case halves.
2. Slide the CR 2032 battery from the battery holder paying attention to the battery
orientation's (+) side facing away from the circuit board.
3. Replace the battery with a new one.
4. Reassemble the case in reverse order of disassembly.
3

128-9479
4 of 4
© 2017 Voxx Electronics Corporation., 180 Marcus Blvd., Hauppauge, NY 11788 128-9479
PATENTED: www.voxxintl.com/company/patents
To purchase replacement transmitters or to get additional product
information go to: www.prestigecarsecurity.com
FCC COMPLIANCE
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Warning!
Changes or modications made to this equipment not expressly approved by the part responsible for compliance could
void the use’s authority to operate the equipment
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this
equipment. Such modications could void the user’s authority to operate the equipment.
FUNCTION SETTING CHART
To be completed by installer
Run Time _______Min 
Door Lock Timer _______Sec 
Parking Lights Pulse Steady 
WARNING!
A running vehicle produces dangerous carbon monoxide gas which can
be fatal if prolonged exposure occurs. Be certain the vehicle is outdoors
before activating the remote start function.
4