Vxl Itona TC61yy User manual

1
Itona TC61yy
Itona TC63yy
Hardware User’s Guide
VXL Instruments Ltd,
No.17, House of Excellence,
Electronics City,
Hosur Road,
Bangalore – 560 100, INDIA
www.vxl.net

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Copyright and Trademark Notices 2
Copyright and Trademark notices
ALL RIGHTS RESERVED.
Information in this document is subject to change without notice and does not represent a commitment
on the part of the manufacturer. No part of this guide may be reproduced or transmitted in any form or
means, electronic or mechanical, including photocopying and recording, for any purpose, without the
express written permission of the manufacturer.
Every effort has been made to make this guide as complete and as accurate as possible, but no
warranty or fitness is implied. The authors and the publisher shall have neither responsibility nor liability
to any person or entity with respect to loss or damages arising from the use of information contained in
this guide. This disclaimer does not apply in countries where such provisions are inconsistent with local
law.
All Trademarks are acknowledged.
Document Number: 600011052669 Rev. A01
First Edition: JANUARY 2010

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
FCC statement and Warning 3
Federal Communication Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment Off and On, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Re-orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio / television technician for help.
Each Thin Client is equipped with a FCC compliance label that shows only the FCC identification
number. The full information of the associated label is as follows:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Warning
•DO NOT open enclosure, Hazard voltages present inside equipment.
•Ensure that all expansion slots (on the back or side of the computer) are covered with metal
retaining brackets, and tightly attached to the computer cabinet.
•Only equipment certified to comply with Class B (computer input/output devices, terminals, printer’s
etc.) should be attached to this equipment, and must have shielded interface cables.
•Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
•This equipment should not be used in Electro-medical applications.
•There are no user serviceable parts inside. DO NOT open enclosure, Hazard voltages present
inside equipment. DO NOT disassemble the equipment as this can nullify your warranty
•DO NOT operate this equipment in corrosive or explosive atmosphere.
•DO NOT operate this equipment outside specified temperature limits.
•This equipment must be earthed.
•The AC socket outlet shall be installed near the equipment and shall be easily accessible.
•Replace the Battery only with the same or equivalent type recommended by the manufacturer.

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Preface 4
Preface
Thank you for purchasing the Itona TC61yy / TC63yy. This guide contains information to setup and use
the hardware of Itona TC61yy / TC63yy.
The guide consists of the following chapters:
•Introduction: provides an overview of the product.
•Installation: contains the procedure to setup the hardware.
•Specifications: provides hardware, mechanical, electrical, interface and operating environment
specifications.
•Connectors and Cables: provides detailed specifications for connectors and cables used with the
product.
•Troubleshooting: provides solutions to problems that you may encounter while using the product.

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Table of Contents 5
Table of Contents
Introduction........................................................................................................................................6
Overview..........................................................................................................................................................6
Installation.................................................................................................................................... 7-10
Specifications...................................................................................................................................11
Hardware .........................................................................................................................................11
Mechanical ..................................................................................................................................................11
Environmental Operating.............................................................................................................................12
Electrical......................................................................................................................................................13
Connectors and Cables ...................................................................................................................14
Connectors..................................................................................................................................................14
COM Port...................................................................................................................................................14
Printer Port (Parallel).................................................................................................................................14
10/100/1000 LAN Port...............................................................................................................................15
Video Port..................................................................................................................................................15
Mouse / Keyboard Port..............................................................................................................................15
Audio / Microphone Port............................................................................................................................15
USB Port....................................................................................................................................................15
Cables .........................................................................................................................................................16
10/100 /1000 LAN Cable...........................................................................................................................16
COM Port (Serial Port) Cables..................................................................................................................16
Printer Cable..............................................................................................................................................18
Troubleshooting...............................................................................................................................19

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Introduction 6
Introduction
Overview
This guide covers hardware details of Itona TC61yy and TC63yy.
Itona TC61YY Itona TC63YY
Front View
Itona TC61yy / TC63yy deliver smart and robust solutions for Thin Client computing. They are
aesthetically and ergonomically designed compact desktop. Itona series thin clients offer
fanless CPU solution to enhance reliability.
Switch
USB Port

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Introduction 7

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Installation 8
Installation
Step One: Unpack
Unpack the unit taking care not to drop the product whilst removing from the packaging.
The carton in which the product was shipped to you contains the following:
•Itona TC61yy / TC63yy
•Power Cord (Optional)
•Wall Mounting Bracket –Single side
When you open the carton, if you find any discrepancy between the contents of the carton and the
above list, contact the dealer or reseller from whom you have purchased the product, immediately.
NOTE:PLEASE RETAIN THE ORIGINAL CARTON AND PACKING MATERIAL.THEY WOULD BE REQUIRED TO
AVOID DAMAGE DURING TRANSIT (IF REQUIRED IN FUTURE).
Step Two: Prepare
1. The site where you want to install the product must have the following
•100~240V AC, 1.2A, 50/60 Hz, 3-pin power Inlet for client (Itona TC61yy / TC63yy).
NOTE:ENSURE THAT THE POWER INLET PLUG IS PROPERLY REGULATED AND EARTHED.AFLOATING
GROUND /CHASSIS COULD CAUSE AN ELECTRIC SHOCK.
•Well ventilated, clean, dry and dust free atmosphere.
•Ensure a minimum space of 2 inches (5 cm) on all sides of the unit for efficient convection
cooling.
•The product can only be used in vertical position
Caution – This Product cannot be placed flat on desk as it will block the ventilation opening and
affect the heating effect.
Note: - For more Details – Refer to Installation and Best Practices Guide.
9
9

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Installation 9
Step Three: Connect accessories and power
NOTE:BEFORE CONNECTING ANY CABLES,ENSURE POWER CABLE IS UNPLUGED FROM THE UNIT. PLEASE
USE 6A (MIN) /250V AC0.75sq mm, 18AWG 3C, H05VV-F /SVT / SPT-2, CERTIFIED POWER CORD.
Pictures below show the various connectors available on the rear panel of the Itona TC61yy and
TC63yy.
Itona TC61yy / Itona TC63yy
Rear view
9
MIC
4 x USB PORT
COM PORT
SVGA PORT
PS/2 KBD
AC POWER OUT
AC POWER IN
AUDIO LINE OUT
2 x EHTERNET PORT
COM PORT 2
LPT PORT
PS/2 MOUSE PORT

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Installation 10
The table below identifies the devices to be used with each connector of the client.
Ensure that COM, VGA and Parallel ports are adequately fastened with the screws provided with the cables.
Ports
Connector Symbol
9Video port
9USB ports
9LINE OUT port
9Microphone input port
9PS/2 Keyboard port
9PS/2 Mouse port
9COM port
9Parallel / LPT port
9Ethernet port 1
9Ethernet port 2


VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 11
Specifications
Hardware
•Processor: Intel Atom N270 1.6 GHz
•VGA Memory: Shared Video Memory 64MB min, 128MB max.
•HDD 2.5” : SATA HDD 2.5 inch.
•Flash : IDE 44 Pin
•RAM: 128MB ~ 2GB DDRII 533/667
•Networking 1 : 10/100Mbps
•Networking 2 : 10/100/1000Mbps
•Display resolution: 16/32 Bits 1920x1200 @60Hz max
•Power Supply : Internal Power Supply
Mechanical
Itona 61yy / TC63yy
Product Dimension Packed Unit Dimension
268mm (H) x 50mm (W) x250mm (D) 155mm (H) x 360mm (W) x 385mm (D)
Net Weight: 3.0Kgs Approx Gross Weight: 6.0Kgs Approx
W
H
D
D
H
W

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 12
PROCEDURE FOR FIXING
SINGLE SIDE WALL MOUNTING BRACKET for Itona TC61yy and TC63yy
STEPS
1. Wall
2. Drill holes and Insert Wall Plug M7x33, 4no
3. Place Single Side Wall Mounting Bracket
4. Fix Self taped Screws M4x24, 4no
5. Place the Unit
6. Fix Thumb Screws M3x8, 4nos
5
1
4
2
3
6

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 13
Environmental Operating
•Temperature : + 5oC to +40oC
•Storage temperature: - 20o C to +65oC
•Humidity: 20% to 80% RH non-condensing
Electrical
•Line Voltage: 100V to 240V AC (+6, -10%)
•Line Frequency: 50 / 60 Hz
•Power Inlet: 1.2A, 3-pin power plug (IEC 320)
•Power Outlet: 3-pin power socket (IEC 320 )
Note: for Devices upto 0.30A max., 100VAC~50/60Hz.
for Devices upto 0.12A max., 240VAC~50/60Hz.
•MTBF > 50,000 Hrs
Regulatory Certifications
RoHS

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 14
Connectors and Cables
Connectors
The following tables provide pin details for various connectors on the rear panel of the client.
COM Port
9-pin D-type male connector. RS232C compatible, operating at 115.2K baud maximum
Pin Signal Description
1 DCD Data Carrier Detect
2 RxD Receive Data
3 TxD Transmit Data
4 DTR Data Terminal
Ready
5 GND Signal Ground
6 DSR Data Set Ready
7 RTS Request To Send
8 CTS Clear To Send
9 NC Not Connected
Printer Port (Parallel)
25-pin D-type female connector. ECP/EPP compatible.
Pin Signal
1 STROBE
2 - 9 DATA 0 – 7
10 ACKNOWLEDGE
11 BUSY
12 PAPER END
13 SLCT
14 AFD
15 ERROR
18 - 25 GROUND
1 5
6 9
13 1
25 14

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 15
10/100/1000 LAN Port
RJ-45 modular 8-pin jack. 10/100 Mbps
Pin Signal
1 TxD+
2 TxD-
3 RxD+
6 RxD-
Video Port
15-pin D-type female connector
Pin Signal Pin Signal Pin Signal
1 Red 6 Red return GND 11 No Connection
2 Green 7 Green return GND 12 No Connection
3 Blue 8 Blue return GND 13 Horizontal Sync
4 No Connection 9 No Connection 14 Vertical Sync
5 GND 10 No Connection 15 No Connection
Mouse / Keyboard Port
PS/2 Mouse / Keyboard connector
Pin Signal Pin Signal
1 Mouse / KBD data 4 VCC
2 NC 5 Mouse / KBD Clock
3 GND 6 NC
Audio / Microphone Port
Standard audio jacks.
USB Port
4-pin series-A receptacle. 4~ 5 ports depending on the model. Both USB1.1 and USB2.0 models are
available.
Pin Signal
1 VCC
2 D-
3 D+
4 GND
6 5
4 3
2 1
1 8
5 1
10 6
15 11

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 16
Cables
10/100/1000 LAN Cable
Cross Connection - (Without Hub)
Straight Connection - (With Hub)
COM Port (Serial Port) Cables
Serial devices like modems and printers use 25 pin D-type connectors for RS232 connections. In
order to connect an RS232 device with a 25-pin connector, 9-pin connector signals must be converted
to 25-pin connector signals as shown in the following diagram.
9-pin to 25-pin Cross Connection
TXD+ 1 3 RXD+
TXD- 2
2 TXD-
RXD+ 3 1 TXD+
RXD- 6
6 RXD-
RJ45
Pin RJ45 Pin
TXD+ 1 1 TXD+
TXD- 2
6 RXD-
RXD+ 3 3 RXD+
RXD- 6
2 TXD-
RJ45
Pin RJ45 Pin
9 Pin
Connector 25 Pin
Connector
3RXD
2TXD
5CTS
4RTS
6DSR
7SGND
8DCD
20 DTR
TXD 3
RXD 2
RTS 7
CTS 8
DSR 6
SGND 5
DCD 1
DTR 4
(Thin Client)

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Connectors and Cables 17
9-pin to 25-pin Straight Connection
Printer Cable
The following table shows the pin connections of the Standard Centronics parallel cable. Some
manufacturers change pin functions or polarity on their printers. For such printers, custom cables may
be necessary. Refer to your printer manual for cabling information in such cases.
Note: Please use certified shielded cable only.
1
2-9
10
11
12
15
18-25
- Strobe
+ Data Bits 0 - 7
- Acknowledge
+ Busy
+ Paper End
- Error
Ground
PARALLEL
PORT PARALLEL
DEVICE
7
4
3
5
1
2
6
8
4
20
2
7
8
3
6
5
9 Pin
Connector
(Thin Client)
25 Pin
Connector
RTS
DTR
TXD
GND
DCD
RXD
DSR
CTS
RTS
DTR
TXD
GND
DCD
RXD
DSR
CTS

VXL Instruments Ltd. Itona TC61yy/TC63yy Hardware User’s Guide
Troubleshooting 18
Troubleshooting
This chapter contains solutions for problems you may encounter while using the product.
Problem Solution
•The Power-LED on front
panel does not glow when
the client is switched on.
9Ensure that the power cord is plugged into an AC outlet.
9Check the fuse in the power-plug, if available.
•There is no display, though
the power-indicating LED
glows.
9Ensure that the video cable is properly connected.
•The mouse (or keyboard)
does not work when the
client is switched on.
9Ensure that the mouse (or keyboard) is plugged into the
correct PS/2 port on the rear panel