WAGO 750 Series User manual

Pos:2/Dokumentationallgemein/Einband/EinbandHandbuch- D ec kbl att ohne Varia nt enfel d ( Sta n dar d) @ 9\mod_1285229289866_0.docx@ 64941@ @ 1
Manual
WAGO-I/O-SYSTEM 750
Serial Interface RS-232 / RS-485
750-652
Configurable
1.2.0
Pos: 3/ All e S eri en (Al lg em eine M od ul e)/Hi nw eise zur D oku men tat ion/I m pres sum für St and ard han dbüc h er - all g. Ang aben, A nschri ften, Tel efonn ummer n und E-Mail -Adr essen @ 3\mod _1219 151118203_21.docx @ 21060 @ @1

2 WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
© 2013 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]om
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]om
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende d er Liste f ür T e xtmar ke Ei nb and _v orne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 5/ Do ku ment ati on all ge mein /V erzei ch niss e/I nhal tsv erz eich nis - Ü ber schrif t oG und Verz eich nis @ 3\mod_1219151230875_21.docx@ 21063@ @ 1
Table of Contents
1Notes about this Documentation................................................................. 6
1.1 Validity of this Documentation................................................................. 6
1.2 Copyright................................................................................................... 6
1.3 Symbols..................................................................................................... 7
1.4 Number Notation....................................................................................... 9
1.5 Font Conventions ...................................................................................... 9
2Important Notes......................................................................................... 10
2.1 Legal Bases ............................................................................................. 10
2.1.1 Subject to Changes............................................................................. 10
2.1.2 Personnel Qualifications..................................................................... 10
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions.... 10
2.1.4 Technical Condition of Specified Devices......................................... 11
2.2 Safety Advice (Precautions).................................................................... 12
3Device Description ..................................................................................... 14
3.1 View........................................................................................................ 18
3.2 Connectors............................................................................................... 19
3.2.1 Data Contacts/Internal Bus................................................................. 19
3.2.2 Power Jumper Contacts/Field Supply ................................................ 20
3.2.3 CAGE CLAMP®Connectors............................................................. 22
3.3 Display Elements .................................................................................... 23
3.4 Operating Elements................................................................................. 24
3.5 Schematic Diagram................................................................................. 24
3.6 Technical Data ........................................................................................ 25
3.6.1 Device Data ........................................................................................ 25
3.6.2 Supply................................................................................................. 25
3.6.3 Communication .................................................................................. 25
3.6.4 Interface.............................................................................................. 26
3.6.5 Climatic Environmental Conditions................................................... 26
3.7 Approvals................................................................................................ 27
3.8 Standards and Guidelines........................................................................ 27
4Process Image............................................................................................. 28
4.1 Operating Modes for Serial Transmission .............................................. 28
4.2 Data Exchange Mode.............................................................................. 30
5Function Description ................................................................................. 32
5.1 Operating Modes for Serial Transmission .............................................. 32
5.1.1 Transmit Data..................................................................................... 32
5.1.1.1 Continuous Transmission .............................................................. 32
5.1.2 Receive Data....................................................................................... 33
5.1.2.1 Continuous Receipt........................................................................ 33
5.1.3 RS-232 Operating Mode..................................................................... 34
5.1.3.1 Flow Control Using XON-/XOFF Protocol .................................. 34
5.1.3.2 Flow Control Using RTS/CTS....................................................... 34
5.1.3.3 Flow Control Using RTS/CTS, RTS with Lead/Follow-on Time. 34
5.1.4 RS-485 Operating Mode..................................................................... 35
5.1.5 RS-422 Operating Mode..................................................................... 35

4 Table of Contents WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
5.1.6 DMX Operating Mode ....................................................................... 35
5.2 Data Exchange Operating Mode ............................................................. 36
6Mounting..................................................................................................... 38
6.1 Mounting Sequence................................................................................. 38
6.2 Inserting and Removing Devices ............................................................ 39
6.2.1 Inserting I/O Module.......................................................................... 39
6.2.2 Removing the I/O Module.................................................................. 40
7Connect Devices ......................................................................................... 41
7.1 Connecting a Conductor to the CAGE CLAMP®................................... 41
7.2 Connection Examples.............................................................................. 42
7.2.1 RS-232 Operating Mode..................................................................... 42
7.2.2 RS-485 Operating Mode..................................................................... 43
7.2.3 RS-422 Operating Mode..................................................................... 45
7.2.4 DMX Operating Mode ....................................................................... 45
7.2.5 Data Exchange Mode ......................................................................... 46
8Commissioning........................................................................................... 47
8.1 Configuration and Parameterization with WAGO-I/O-CHECK............. 47
8.1.1 RS-232 / RS-485 Serial Interface (Configuration Dialog)................. 47
8.1.2 Toolbar on the Configuration Dialog................................................. 48
8.1.3 Process Image Size............................................................................. 49
8.1.4 Parameter Range................................................................................. 50
8.1.5 Setting the RS-232 / RS-485 Serial Interface..................................... 51
8.2 Configuration and Parameterization via GSD for PROFIBUS DP and
PROFINET IO ........................................................................................ 52
8.3 Data Transfer........................................................................................... 52
8.3.1 Example of Operating Modes for Serial Transmission...................... 52
8.3.2 Initialization........................................................................................ 53
8.3.3 Transmission of the Character String "Hello World!" ....................... 54
8.3.4 Receiving the Character String "WAGO".......................................... 54
8.3.5 Operation with Continuous Send........................................................ 55
8.3.5.1 Transmission of a block of one to 512 bytes................................. 55
8.3.5.2 Transmission of a block of more than 512 bytes........................... 56
8.3.6 DMX Application Example................................................................ 58
8.3.6.1 Operation with Deactivated Continuous Send............................... 58
8.3.6.2 Operation with Activated Continuous Send .................................. 58
8.3.7 Data Exchange Operating Mode Application Example ..................... 59
9Diagnostics.................................................................................................. 60
9.1 Serial Operating Modes........................................................................... 60
9.2 Data Exchange Operating Mode ............................................................. 60
10 Use in Hazardous Environments.............................................................. 61
10.1 Marking Configuration Examples........................................................... 62
10.1.1 Marking for Europe according to ATEX and IEC-Ex........................ 62
10.1.2 Marking for America according to NEC 500..................................... 65
10.2 Installation Regulations........................................................................... 66
10.2.1 Special Conditions for Safe Operation of the ATEX and IEC Ex (acc.
DEMKO 08 ATEX 142851X and IECEx PTB 07.0064)................... 67

WAGO-I/O-SYSTEM 750 Table of Contents 5
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
10.2.2 Special conditions for safe use (ATEX Certificate TÜV 07 ATEX
554086 X)........................................................................................... 68
10.2.3 Special conditions for safe use (IEC-Ex Certificate TUN 09.0001 X)70
10.2.4 ANSI/ISA 12.12.01 ............................................................................ 72
11 Appendix..................................................................................................... 74
11.1 Configuration and Parameterization via GSD for PROFIBUS DP and
PROFINET IO ........................................................................................ 74
11.1.1 Configuration of the RS-232/RS-485 Interface.................................. 74
11.1.1.1 PROFIBUS DP (750-333, 750-343, 750-833) Fieldbus Coupler
PROFINET IO (750-370) Fieldbus Coupler ................................. 74
11.1.1.2 PROFINET IO (750-375, 750-377) Fieldbus Coupler.................. 74
11.1.2 Configuration of the RS-232/RS-485 Serial Interface ....................... 75
11.1.2.1 All PROFIBUS DP and PROFINET IO Fieldbus Couplers.......... 76
11.1.2.2 PROFIBUS DP (750-333, 750-343, 750-833) Fieldbus Coupler
PROFINET IO (750-370) Fieldbus Coupler ................................. 78
11.1.2.3 PROFINET IO (750-375, 750-377) Fieldbus Coupler.................. 78
List of Figures...................................................................................................... 79
List of Tables........................................................................................................ 80
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 7/ All e S eri en (Al lg em eine M od ul e)/Üb ers chr ift en für all e S erie n/Hi n weis z ur D ok umen ta tion/ Hin weis e z ur D o kume ntati on - Ü b ersc hri ft 1 @ 4\mod_1237987661750_21.docx@ 29029 @ 1@ 1
1 Notes about this Documentation
Pos: 8/ All e S eri en (Al lg em eine M od ul e)/Hi nw eise zur D oku men tat ion/H i nweis e/H in weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx@ 29026 @ @1
Keep this documentation!
The operating instructions are part of the product and shall be kept for the entire
lifetime of the device. They shall be transferred to each subsequent owner or user
of the device. Care must also be taken to ensure that any supplement to these
instructions are included, if applicable.
Pos: 9/ All e S eri en (Al lg em eine M od ul e)/Üb ers chr ift en für all e S erie n/Hi n weis z ur D ok umen ta tion/ Gül tig kei tsber ei ch - Ü bersc hrift 2 @ 12\mod_1338912448776_21.docx@ 96469@2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S erie 7 50 (WA GO-I/O-SYS TEM )/H in weis e z ur D ok ument ati on/ Gül tigk eits ber eic hD okum entati on Bus klem me 750-xxx x, Stan dard versio n und aufg elist ete Var iante n @ 14\mod_1358944038682_21.docx@ 109354@ @ 1
This documentation is only applicable to the I/O module 750-652 (Serial Interface
RS-232 / RS-485) of the WAGO-I/O-SYSTEM 750 series and the variants listed
in the table below.
Pos: 11 /S erie 7 50 (WA GO-I/O-SYS TEM )/H in weis e z ur D ok ument ati on/ Var iant enli ste n/V aria nte nli ste - 750- xxx- Sta ndard versio n und Var iant e/ 025-00 0 ( erw eit ert er T em per atur ber eic h) @ 9\mod_1281521920414_21.docx@ 63093@ @ 1
Table 1: Variants
Item Number/Variant
Designation
750-652
Serial Interface RS-232 / RS-485
750-652/025-000
Serial Interface RS-232 / RS-485/T
Pos: 12 /A lle Ser ien (Al lge meine Mo dule)/ Hin weise zur D oku mentati on/H inwei se/Hi nweis : Gülti gkeit d er Anga ben für a ufgel istete V aria nten @ 9\mod_1281520778141_21.docx@ 63085@ @ 1
Documentation Validity for Variants
Unless otherwise specified, basic version 750-652data also applies to listed
variants.
Pos: 13 /S erie 7 50 (WA GO-I/O-SYS TEM) /Hi nweis ez ur Do kume ntati on/Hi nweis e/Ac htung : Hinw eis zur D oku ment ation B uskl emme n 750-xxxx @ 4\mod_1237986979656_21.docx@ 29023@ @ 1
The I/O module 750-652 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 14 .1 /All e Seri en( Allg emeine M odul e)/Hi nweis e zur Do kument ation /Urh ebersc hutz au sführ lich @ 4\mod_1235565145234_21.docx @ 27691@ 2@ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos:14.2/Dokumentationallgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1
Pos: 14 .3 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Hin weis zur D oku mentati on/S ymbol e- Ü b erschr if t 2 @ 13\mod_1351068042408_21.docx@ 105270@ 2 @ 1
1.3 Symbols
Pos: 14.4 .1 /Alle Ser ien (Al lge meine Mo dule)/ Wic htige Erl äuter unge n/Sic herhei ts- undsonstigeHinweise/Gefahr/Gefahr: _Warnung vorPersonenschädenallgemein_- Erl äu ter ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 14 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nstig eH inwei se/G efahr /Gefa hr: _War nung vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung@ 13\mod_1343309694914_21.docx@ 101030@ @1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 14 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und s ons tig e Hin wei se/ War nung /W arn ung: _War nu ng vor Per so nensc h äde n allg em ein_ - Erläuterung @ 13\mod_1343309877041_21.docx@ 101035@ @1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 14 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und s ons ti ge H in weis e/ Vors ic ht/ Vor sich t: _War nung vor P ers on ensc hä den al lg emei n_ - Erläuterung@ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 14 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Achtung/Achtung:_Warnung vorSachschäden allgemein_- Erl äut erung @ 13\mod_1343310134623_21.docx@ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 14 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstigeHinweise/Achtung/Achtung:_Warnung vorSachschäden durchelektrostatische Aufladung_- Erläuterung @13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 14 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- undsonstige Hinweise/Hinweis/Hinweis: _WichtigerHi nweisallgemein_ - Eräuterung@ 13\mod_1343310326906_21.docx@ 101047@ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 14 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und s ons ti ge H in weis e/I nf or mati on/I nf or mati on: _Wei ter e I nfor ma tio n al lg emei n_ -Er l äut er ung @ 13\mod_1343310439814_21.docx@ 101051@ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:14.5/Dokumentationallgemein/Gliederungselemente/---Seite nwec hsel--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 9
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 14 .6 /All e Seri en( Allg emeine M odul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\mod_1221059454015_21.docx@ 21711@ 2 @ 1
1.4 Number Notation
Table 2: Number notation
Number code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 14 .7 /All e Seri en( Allg emeine M odul e)/Hi nweis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx@21714 @ 2 @ 1
1.5 Font Conventions
Table 3: Font conventions
Font type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Programme\WAGO-I/O-CHECK
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 15 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

10 Important Notes WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 16 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erien/Wichtige Erläuterungen/WichtigeErläuterungen- Üb ersc hrift 1 @ 4\mod_1241428899156_21.docx@ 32170 @ 1 @ 1
2 Important Notes
Pos: 17 .1 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/Ei nleit ung Wic htige E rläut erung en @ 3\mod_1221059818031_21.docx@ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 17 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Wich tige Er läuter ung enRec htlic he Grun dlag en -Ü bersc hrift 2 @ 3\mod_1221060626343_21.docx@ 21726@ 2 @ 1
2.1 Legal Bases
Pos: 17.3/Alle Serien(AllgemeineDokumente)(Allgemeine Module)/WichtigeErläuterungen/Änderungsvorbehalt- Ü bers chrift 3 u ndI nhalt @ 3\mod_1221060036484_21.docx@ 21720@ 3@ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos:17.4/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Per sonal qual ifika tion 75 0-xxxx@ 3 \mod_1224061208046_21.docx@ 24063@ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on Series 750 devices may only be carried out by
electrical specialists with sufficient knowledge in automation. The specialists
must be familiar with the current norms and guidelines for the devices and
automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos:17.5/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Bes timm ungsg emäß e Verwe ndung 7 50-xxxx @ 3\mod_1224064151234_21.docx@24070 @ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to the actuators or higher-level control systems. Using programmable controllers,
the signals can also be (pre-) processed.
The components have been developed for use in an environment that meets the
IP20 protection class criteria. Protection against finger injury and solid impurities
up to 12.5 mm diameter is assured; protection against water damage is not
ensured. Unless otherwise specified, operation of the components in wet and
dusty environments is prohibited.
Operating 750 Series components in home applications without further measures
is only permitted if they meet the emission limits (emissions of interference)
according to EN 61000-6-3. You will find the relevant information in the section
on "WAGO-I/O-SYSTEM 750" "System Description" "Technical Data" in
the manual for the used fieldbus coupler/controller.

WAGO-I/O-SYSTEM 750 Important Notes 11
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 17 .6 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/T echnis cher Z ustan d der Ger äte - Übers chri ft 3 und Inh alt @ 3\mod_1221060446109_21.docx@ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The components to be supplied Ex Works, are equipped with hardware and
software configurations, which meet the individual application requirements.
WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in
case of changes in hardware or software as well as to non-compliant usage of
components.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos:17.7/Dokumentation allg emei n/ Gli eder ung s elem ent e/---Sei te nwec hsel ---@ 3\mod_1221108045078_0.docx@ 21810@ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 17 .8 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte nf ür alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e- Üb ersc hri ft 2 @ 6 \mod_1260180299987_21.doc x@ 46 724 @ 2@ 1
2.2 Safety Advice (Precautions)
Pos: 17 .9 /All e Seri en( Allg emeine D okum ente) ( Allg emeine M odule) /Wic htige Er läut erung en/Si cherh eits hinwei se/Ei nleit ung Sic herh eits hin weis e H ard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 17.1 0.1 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /G efahr /G ef ahr: Nicht an Gerät en unter Spa nnung ar beit en! @ 6\mod_1260180365327_21.docx@ 46727@ @ 1
Do not work on components while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 17.1 0.2 / Ser ie 75 0 ( WAG O-I/O-SY STE M)/Wi cht ig e Erl äu ter ung en/Si cher hei ts- un d s onst ige H i nwei se/ Gef ahr/ Gef ahr: Einb au 0 750-x xxx nur i n Gehäus en, Sc hrän ken oder el ektri sche n Betri ebsrä umen! @ 6\mod_1260180556692_21.docx@ 46731@ @ 1
Installation only in appropriate housings, cabinets or in electrical operation
rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 17.1 0.3 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /G efahr /G ef ahr: U nfal l verh ütung s vorsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735@ @ 1
Pos: 17.1 0.4 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /G efahr /G ef ahr: A uf n ormg er echt e n Ansc hlu ss acht en! @ 6\mod_1260180753479_21.docx@ 46739@ @1
Pos: 17.1 1.1 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Erläut erung en/Sic her heits hinwei se/Ac htung /Acht ung: De fekt e oder bes chädi gte Ger äte aus tausc hen! @ 6 \mod_1260180857358_21.docx@ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 17.1 1.2 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : Gerä te vor kri eche nden u ndis olier end en Stoff en schüt zen! @ 6\mod_1260181036216_21.docx@ 46747@ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 17.1 1.3 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : Rei ni gu ng n ur mi t zul äs sig en M at erial ien! @ 6\mod_1260181203293_21.docx@ 46751@ @ 1
Cleaning only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 17.1 1.4 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : K ein K o nta ktspr ay verwe nde n! @ 6\mod_1260181290808_21.docx@ 46755@ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 13
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 17.1 1.5 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : V erp olung ver mei den! @ 6\mod_1260184045744_21.docx @ 46767@ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 17.1 1.6 / Alle Seri en ( Allg em ein e D oku ment e) ( Allg em eine M o dul e)/ Wich tig e Er läut eru ngen /Sic h erh eits hin weise /Ac htu ng/ Acht ung : El e ktr ost atisc h e Ent l adu ng vermei de n! @ 6\mod_1260181364729_21.docx@ 46759@ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that you may destroy by
electrostatic discharge when you touch. Pay attention while handling the devices
to good grounding of the environment (persons, job and packing).
Pos: 18 /D oku ment ation al lg emei n/ Gli eder ung s elem ent e/---Sei te nwec hsel ---@ 3\mod_1221108045078_0.docx@ 21810@ @ 1

14 Device Description WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 19 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Gerä tebes chrei bung - Üb ersc hrift 1 @ 3\mod_1233756084656_21.docx@ 27096 @ 1 @ 1
3 Device Description
Pos:20.1/Serie750(WAGO-I/O-SYSTEM)/Gerätebeschreibung/Einleitung/Anwendung/SO/Anwendung750-065 2_Da tenaus tausc hkl emme @ 15 \mod_1366288638779_21.docx@ 117310@ @ 1
The I/O module 750-652 (Serial Interface RS-232 / RS-485) allows the optional
connection of devices with a RS-485, RS-422 or RS-232 interface.
It also provides gateways between the serial interface and the fieldbus systems
supported by the WAGO-I/O-SYSTEM 750.
No higher protocol level is required by the module. Communication to the
associated fieldbus master is completely transparent. This provides for a broader
application scope for the serial interface module. If required, communication
protocols can be configured via fieldbus master.
The 2560 byte input buffer provides for high data baud rates. At lower baud rates,
the data received in lower priority tasks is evaluated without data loss.
The 512-byte output buffer provides fast transmission of larger data strings.
The operating mode of the I/O module can be configured with the start-up tool
WAGO-I/O-CHECK 3.3 (firmware version 03 or higher requires WAGO-I/O-
CHECK version 3.5.3 or higher).
NOTE
The default operating mode is RS-485 half-duplex. The default data transmission
rate is 9600 baud. 1 start bit, 8 data bits and 1 stop bit are send. There is no parity
generation and dataflow control.
Before starting operation, the connections of the I/O module must be cabled
appropriately. (see "Connection examples" section)
In RS-232 mode, the interface works in accordance with the TIA/EIA-232-F and
CCITT V.28/DIN 66259-1 standards.
In RS-485/RS-422 mode, the interface works in accordance with the TIA/EIA-
485-A, DIN 66259 standards.
The connected device can communicate directly with the control unit via the
fieldbus coupler/controller used.
The active communication channel works independent of the fieldbus system used
in full or half-duplex operation at up to 115200 baud.
Pos: 20 .2 /Ser ie 750(WAGO-I/O-SYST EM) / Ger äteb esc hrei bu ng /Ei nlei tu ng/A n wend ung /SO An we ndu ng 7 50-06 52 D aten flus ss teu eru ng, D at ena ustau sch und D MX-M od us @ 15\mod_1366289566565_21.docx @ 117314@ @1
In the data flow control through RTS/CTS in RS-232 mode, a lead time or follow-
on time can be configured for the I/O module for the RTS signal. This function is
available with firmware version 03 or higher.
Direct data exchange between different fieldbus nodes of the 750 series is possible
in conjunction with a second I/O module. This function is available with firmware
version 03 or higher.

WAGO-I/O-SYSTEM 750 Device Description 15
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
The I/O module can be configured as a DMX sender with a baud rate of
250 kBits/s. This function is available with firmware version 03 or higher.
Pos:20.3/Serie750( WAGO-I/ O-SYST EM )/ Ger äte besc hr ei bung /Ei nlei tu ng/ I/O -Besc hrei bu ng/ SO/I/ I/O-B eschrei bung 750-0652– Datenaustauschmodus@ 13\mod_1355144859102_21.docx@ 107490@ @ 1
The wiring to the communication partner takes place in RS-232 mode via the
TxD, RxD connections, if necessary RTS/CTS and ground (G) and in the RS-
485/RS-422 mode via the connections A, B, X, Y, and ground.
Pos:20.4/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes chr eibu ng/ AI/I /O-Bes chr eib ung 750-04x x A I S chir m ansc hl uss Kontakt mitTragschiene@ 5\mod_1246367742653_21.docx@ 36360@ @ 1
The shield connection is fed directly to the carrier rail and contact is made
automatically by snapping the module onto the rail.
Pos:20.5/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /I/ O-Bes c hrei bung / All gem ein/ Ver weis auf Kapi tel "Ansc hl üss e" @ 8\mod_1276775378035_21.docx@ 57956@ @ 1
The assignment of the connections is described in the "Connections" section.
Pos:20.6/Serie750( WAGO-I/ O-SYST EM )/ Ger äte besc hr ei bung /Ei nlei tu ng/ I/O -Besc hr ei bung /Al lg emei n/V er weis auf K a pitel "Ger ät e a nschl i eß en" > "Ans chl us sbei s piel( e)" @ 5\mod_1246015203281_21.docx@ 36298@ @ 1
Connection examples are shown in section "Connecting Devices" "Connection
Examples".
Pos:20.7/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /LE D-A nzeig e/LED Zu stan d Betri eb, Kle mmenb us-KommunikationundSignalübertragung @ 6\mod_1257923657453_21.docx@ 44269@ @ 1
Multi-color LEDs indicate the operating status and the trouble-free internal bus
communication as well as the status of the signal transmission.
Pos:20.8/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/Ei nl ei tung /LE D-A nzei ge/ Ver wei s au f Kapit el " Anz eig e ele men te" @ 5\mod_1246010525000_21.docx@ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos:20.9/Serie750(WAGO-I/O-S YSTEM) /Ger ätebes chrei bung /Einl eitung /Ver sorg ung/Ver sorg ung 24 V, 0 V über Lei stu ngsk ontakt e Stand ard @ 3\mod_1226498974531_21.docx @ 25020@ @ 1
The I/O module receives the 24V voltage supply for the field level from an
upstream I/O module or from the fieldbus coupler/controller via the power
contacts used as blade contacts. It then provides this potential to subsequent I/O
modules via the power contacts used as spring contacts.
Pos: 20.1 0 /S erie 750 ( WAG O-I/ O-SYST EM )/G erät ebe sc hr eibu ng /Ei nleit ung /V ers org ung /G al vanisc h e Tr en nung Fel d/S yst em @ 3\mod_1233756478750_21.docx@ 27102@ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 20.1 1 /S erie 750 ( WAG O-I/ O-SYST EM )/G erät ebe sc hr eibu ng /Ei nleit ung /V ers org ung /A nor dnu ng unter Berüc ksic hti gu ng der L eist ung s konta kt e b elie big @ 3 \mod_1233756233468_21.docx@ 27099@ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Pos: 21 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\m od_1221108045078_0.docx@ 21810@ @ 1

16 Device Description WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 22 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Ei ns atz ber eich /Ei ns atz ber eich 750-x xxx n ur K oppl er /C ontr oll er aus K om pati bili tät sli ste @ 4\mod_1242389440265_21.docx@ 33262 @ @1
The 750-652 module can be used with the fieldbus couplers and controllers of the
WAGO-I/O-SYSTEM 750 of the specified version or higher listed in the
"Compatibility list" table.
Pos: 23 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /Ei nlei t ung /Ei ns atz ber eich /Ko mpa ti bili täts lis ten /K om pati bil itä tsli st e 75 0-06 52_D atenau staus ch @ 15\mod_1365497370692_21.docx@ 116820@ @ 1
Table 4: Compatibility list 750-0652
Bus System
Fieldbus
couplers/controllers
Item No.
Firmware
status
PROFINET
Fieldbus couplers
750-370
02
Profibus
Fieldbus couplers
750-333
14
Programmable
fieldbus controller
750-833
14
I/O-IPC*
758-870/
000-111
05
758-870/
000-131
05
758-874/
000-111
05
758-875/
000-111
05
758-876/
000-111
05
ETHERNET
Fieldbus couplers
750-341
07
750-342
17
750-352
02
Programmable
fieldbus controller
750-841
18
750-842
18
750-843
02
750-871
07
750-872
03
750-873
03
750-880
02
750-881
02
750-882
01
I/O-IPC
758-870/
000-110
05
758-870/
000-130
05
758-874/
000-110
05
758-875/
000-110
05
758-875/
000-130
05
758-876/
000-110
05
DeviceNet
Fieldbus couplers
750-306
4K
ECO fieldbus coupler
750-346
10
Programmable
fieldbus controller
750-806
10

WAGO-I/O-SYSTEM 750 Device Description 17
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
CANopen
Fieldbus couplers
750-337
19
750-338
19
ECO fieldbus coupler
750-347
08
750-348
08
Programmable
fieldbus controller
750-837
14
750-838
14
I/O-IPC*
758-870/
000-112
05
758-875/
000-112
05
KNX
Programmable
fieldbus controller
750-849
04
BACnet
Programmable
fieldbus controller
750-830
03
LONWORKS
®
Fieldbus couplers
750-819
09
*Also available via 2 ETHERNET interfaces
Other fieldbus couplers/controllers on request.
Pos: 24 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

18 Device Description WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 25 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung /Ansic ht -Ü b ersc hrif t 2 @ 4\mod_1240984217343_21.docx@ 31958 @ 2@ 1
3.1 View
Pos: 26 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsic ht /S ond er klem men /A nsic ht 750-0652 @ 6\mod_1263997977704_21.docx@ 48200@ @1
Figure 1: View
Table 5: Legend for "View" figure
No.
Designation
Meaning
For details see Section
1 ---
Marking options using the
Mini-WSB
---
2 A … H Status LEDs
"Device description" >
"Display elements"
3 --- Data contacts
"Device description" >
"Connections"
4 1 ... 8
CAGE CLAMP®connections
data inputs
"Device description" >
"Connections"
5 --- Power jumper contacts +24 V
"Device description" >
"Connections"
6 --- Releasing strap
"Install" > "Insert and
remove devices"
7 --- Power jumper contacts 0V
"Device description" >
"Connections"
Pos: 27 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 28 /A lle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle S erie n/Gerä tebes chrei bung/Anschlüsse- Üb ersc hrift 2 @ 4\mod_1240984262656_21.docx@ 31961@ 2 @ 1
3.2 Connectors
Pos: 29 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsc hl üss e/Da te nko nta kt e/Kl em men bus - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx@ 43660@ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Pos:30.1/Serie750(WAGO-I/O-S YST EM)/ Ger äte b esc hrei bu ng/A nsc hl üsse /Da te nkon ta kt e @ 3 \mod_1231771259187_21.docx@ 26002@ @ 1
Communication between the coupler/controller and the I/O modules as well as the
system supply of the I/O modules is carried out via the internal bus. It is
comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data contacts
Pos:30.2/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und sonst ig e Hi nwei se/ Ach tung /A chtu ng: Buskl em men nicht auf Goldf eder kon ta kte l eg en! @ 7\mod_1266318463636_21.docx@ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos:30.3/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- undsonstigeHinweise/Achtung/Achtung:ESD - Auf g ute Er dung der Umg ebung ac hte n! @ 7\mod_1266318538667_21.docx@ 50708@ @ 1
Ensure that the environment is well grounded!
The modules are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the modules, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos: 31 /D oku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750
750-652 Serial Interface RS-232 / RS-485
Manual
1.2.0
Pos: 32 /S erie 7 50 (WA GO-I/O-SYS TEM )/ Ger ät ebes chr ei bung /A nsc hl üss e/Lei st ung s kont akt e/F el dvers orgung- Ü bersc hrift 3 @ 6\mod_1256294692864_21.docx@ 43664@ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos:33.1/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und sonst ig e Hi nwei se/ Vor sic ht/ Vors ich t: V erl etz ungsg efa hr durc h sch arf kan tig e M esser ko nta kte! @ 6\mod_1256193279401_21.docx@ 43414@ @ 1
Risk of injury due to sharp-edged male contacts!
The male contacts are sharp-edged. Handle the module carefully to prevent injury.
Pos:33.2/Serie750(WAGO-I/O-S YSTEM) /Ger ätebes chrei bung /Ansc hlüss e/Lei stung skont akte 2 LK ( Mess er/Leis tung skon takte 2 L K( Messer /Fe der) - Ei nleitung @ 15 \mod_1371721641099_21.docx@ 123714@ @ 1
The I/O module 750-652 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as male contacts and the contacts on the right side as spring
contacts.
Pos:33.3/Serie750(WAGO-I/O-S YSTEM) /Ger äteb eschrei bung /Ansc hlüss e/Lei stung skont akte 2 LK ( Mess er/Leis tung skon takte 2 L K( Messer /Fe der) - A bbildu ng (einf ache Br eite) @ 15\mod_1367500700037_21.docx@ 118396@ @ 1
Figure 3: Power jumper contacts
Pos: 33 .4 /Ser ie 750(WAGO-I/O-SYST EM)/ Geräte besc hrei bung/A nschl üsse /Leist ungs konta kte 2 LK (M esser/ Leis tungs konta kte 2 LK (Me sser /Fed er) - Lege nde @ 15 \mod_1371721352500_21.docx@ 123710@ @ 1
Table 6: Caption acc. to view “Power jumper contacts”
Connector
Type
Function
1 Spring contact
Forwarding of the
field supply voltage (Uv)
2 Spring contact
Forwarding of the
field supply voltage (0 V)
3 Blade contact
Infeed of the
field supply voltage (0 V)
4 Blade contact
Infeed of the
field supply voltage (Uv)
Pos:33.5/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en/Si cherh eits- und s onstig e Hinw eise/ Achtu ng/A chtung :M axi maler S trom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx@ 25029@ @ 1
Do not exceed maximum current via power contacts!
The maximum current to flow through the power contacts is 10 A.
Greater currents can damage the power contacts.
When configuring the system, ensure that this current is not exceeded. If
exceeded, an additional potential feed module must be used.
Pos:33.6/Serie750(WAGO-I/O-SYST EM)/ Wichti ge Erlä uter ung en/ Sich erh eits- u nd sonstig e Hin weis e/Hinw eis/Hi nwei s: Pote ntialei ns peise klemme f ür Erde ei nset zen! @ 3\mod_1226499037468_21.docx@ 25023@ @ 1