WAGO 750-630 User manual

Fieldbus Independent
I/O Modules
SSI Transmitter Interface
750-630
Manual
Version 1.0.2

ii • General
WAGO-I/O-SYSTEM 750
I/O Modules
Copyright 2006 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the correctness and com-
pleteness of this documentation. However, as errors can never be fully ex-
cluded, we would appreciate any information or ideas at any time.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally trademark or patent protected.

Content •iii
WAGO-I/O-SYSTEM 750
I/O Modules
CONTENT
1Important Comments ................................................................................. 4
1.1 Legal Principles........................................................................................4
1.1.1 Copyright ............................................................................................. 4
1.1.2 Personnel Qualification ....................................................................... 4
1.1.3 Intended Use ........................................................................................ 4
1.2 Symbols .................................................................................................... 5
1.3 Number Notation...................................................................................... 5
1.4 Safety Notes ............................................................................................. 6
1.5 Scope ........................................................................................................ 6
2I/O Modules ................................................................................................. 7
2.1 Special Modules ....................................................................................... 7
2.1.1 750-630 (/xxx-xxx) [SSI Transmitter Interface] ................................. 7
2.1.1.1 Variations........................................................................................ 7
2.1.1.2 View................................................................................................ 7
2.1.1.3 Description...................................................................................... 8
2.1.1.4 Display Elements ............................................................................ 9
2.1.1.5 Schematic Diagram......................................................................... 9
2.1.1.6 Technical Data .............................................................................. 10
2.1.1.7 Process Image ...............................................................................11
2.1.1.8 Adjustable Variation 750-630/003-000 ........................................ 13

4 •Important Comments
Legal Principles
WAGO-I/O-SYSTEM 750
I/O Modules
1 Important Comments
To ensure fast installation and start-up of the units described in this manual,
we strongly recommend that the following information and explanations are
carefully read and abided by.
1.1 Legal Principles
1.1.1 Copyright
This manual is copyrighted, together with all figures and illustrations
contained therein. Any use of this manual which infringes the copyright
provisions stipulated herein, is not permitted. Reproduction, translation and
electronic and photo-technical archiving and amendments require the written
consent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will
entail the right of claims for damages.
WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform
modifications allowed by technical progress. In case of grant of a patent or
legal protection of utility patents all rights are reserved by WAGO
Kontakttechnik GmbH & Co. KG. Products of other manufacturers are always
named without referring to patent rights. The existence of such rights can
therefore not be ruled out.
1.1.2 Personnel Qualification
The use of the product detailed in this manual is exclusively geared to
specialists having qualifications in PLC programming, electrical specialists or
persons instructed by electrical specialists who are also familiar with the valid
standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability
resulting from improper action and damage to WAGO products and third party
products due to non-observance of the information contained in this manual.
1.1.3 Intended Use
For each individual application, the components supplied are to work with a
dedicated hardware and software configuration. Modifications are only
permitted within the framework of the possibilities documented in the
manuals. All other changes to the hardware and/or software and the non-
conforming use of the components entail the exclusion of liability on part of
WAGO Kontakttechnik GmbH & Co. KG.
Please direct any requirements pertaining to a modified and/or new hardware
or software configuration directly to WAGO Kontakttechnik GmbH & Co.
KG.

Important Comments •5
Symbols
WAGO-I/O-SYSTEM 750
I/O Modules
1.2 Symbols
Danger
Always abide by this information to protect persons from injury.
Warning
Always abide by this information to prevent damage to the device.
Attention
Marginal conditions must always be observed to ensure smooth operation.
ESD (Electrostatic Discharge)
Warning of damage to the components by electrostatic discharge. Observe
the precautionary measure for handling components at risk.
Note
Routines or advice for efficient use of the device and software optimization.
More information
References on additional literature, manuals, data sheets and INTERNET
pages
1.3 Number Notation
Number Code Example Note
Decimal 100 normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100'
Within ',
Nibble separated with dots

6 •Important Comments
Safety Notes
WAGO-I/O-SYSTEM 750
I/O Modules
1.4 Safety Notes
Warning
Switch off the system prior to working on bus modules!
In the event of deformed contacts, the module in question is to be replaced, as
its functionality can no longer be ensured on a long-term basis.
The components are not resistant against materials having seeping and
insulating properties. Belonging to this group of materials is: e.g. aerosols,
silicones, triglycerides (found in some hand creams).
If it cannot be ruled out that these materials appear in the component
environment, then additional measures are to be taken:
- installation of the components into an appropriate enclosure
- handling of the components only with clean tools and materials.
Attention
Cleaning of soiled contacts may only be done with ethyl alcohol and leather
cloths. Thereby, the ESD information is to be regarded.
Do not use any contact spray. The spray may impair the functioning of the
contact area.
The WAGO-I/O-SYSTEM 750 and its components are an open system. It
must only be assembled in housings, cabinets or in electrical operation
rooms. Access must only be given via a key or tool to authorized qualified
personnel.
The relevant valid and applicable standards and guidelines concerning the
installation of switch boxes are to be observed.
ESD (Electrostatic Discharge)
The modules are equipped with electronic components that may be destroyed
by electrostatic discharge. When handling the modules, ensure that the
environment (persons, workplace and packing) is well grounded. Avoid
touching conductive components, e.g. gold contacts.
1.5 Scope
This manual describes the Digital Input Module 750-630 SSI Transmitter
Interface of the modular WAGO-I/O-SYSTEM 750.
Handling, assembly and start-up are described in the manual of the Fieldbus
Coupler. Therefore this documentation is valid only in the connection with the
appropriate manual.

750-630 (/xxx-xxx) [SSI Transmitter Interface] •7
Variations
WAGO-I/O-SYSTEM 750
I/O Modules
2 I/O Modules
2.1 Special Modules
2.1.1 750-630 (/xxx-xxx) [SSI Transmitter Interface]
2.1.1.1 Variations
Item-No. Designation Description
750-630 SSI/ 24Bit/ 125kHz/ Gray SSI Transmitter Interface
750-630/000-001 SSI/ 24Bit/ 125kHz/ Bin SSI Transmitter Interface
750-630/000-002 SSI/ 24Bit/ 250kHz/ Bin SSI Transmitter Interface
750-630/000-004 SSI/ 24Bit/ 125kHz/ Gray/ Status SSI Transmitter Interface
750-630/000-005 SSI/ 15Bit/ 125kHz/ Gray/ Status SSI Transmitter Interface
750-630/000-006 SSI/ 24Bit/ 250kHz/ Gray SSI Transmitter Interface
750-630/000-007 SSI/ 24Bit/ 83kHz/ Gray/ Status SSI Transmitter Interface
750-630/000-008 SSI/ 25Bit/ 125kHz/ Gray SSI Transmitter Interface
750-630/000-009 SSI/ 13Bit/ 250kHz/ Bin SSI Transmitter Interface
750-630/000-011 SSI/ 25Bit/ 125kHz/ Bin SSI Transmitter Interface
750-630/000-012 SSI/ 13Bit/ 125kHz/ Gray SSI Transmitter Interface
750-630/000-013 SSI/ 29Bit/ 125kHz/ Bin SSI Transmitter Interface
750-630/003-000 Variable configuration SSI Transmitter Interface
2.1.1.2 View
D+ D-
++
--
CL+ CL-
13 14
C
D
B
A
750-630
-D
Power jumper contacts
Data contacts
24V
0V
-CL
Status
+D
+CL
Fig. 2.1.1-2: SSI Transmitter Interface 750-630 g063000e

8 •750-630 (/xxx-xxx) [SSI Transmitter Interface]
Description
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.3 Description
This module is an SSI interface for the direct connection to an SSI transmitter.
The power supply for the transmitter is derived internally from the power
jumper contacts.
After the interface has given a clock pulse to the sensor, the interface reads the
incoming data and transmits it directly in the form of a data word into the
process image of the PLC or PC. It is possible to factory adjust different
operating modes, transfer frequencies and data widths by means of the control
register.
The operational readiness of the module is indicated via a green function
LED.
Any configuration of the specialty modules is possible when designing the
fieldbus node. Grouping of module types is not necessary.
The field side supply voltage of 24 V for the output module is derived from
adjacent I/O modules or from a supply module.The supply voltage for the
field side is made automatically through the individual I/O modules by means
of power jumper contacts.
Attention
The module has no power jumper contact for receiving and transmitting the
ground (earth) potential. A supply module is required, if the adjacent
modules need to be connected to the earth.
Warning
The maximum current of the internal power jumper contacts is 10 A. When
configuring the system it is important not to exceed the maximum/sum
current. However, if such a case should occur, another supply module must
be added.
The module 750-630 and its variations can be used with all
couplers/controllers of the WAGO-I/O-SYSTEM 750 (except for the economy
types 750-320, -323, -324 and -327).
This description is valid from hardware and software version XXXX3A05...
and up. The version is specified in the manufacturing number, which is part of
the lateral marking on the module.

750-630 (/xxx-xxx) [SSI Transmitter Interface] •9
Display Elements
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.4 Display Elements
LED Channel State Function
off
Watchdog Timer Overflow *
* The green LED goes off if no process
data is transmitted by the fieldbus
coupler / controller for 100 ms.
13 14
C
D
B
A
A
Fig. 2.1.1-1:
Display Elements
g063002x
A
green Status
on Normal operation
2.1.1.5 Schematic Diagram
Status
Logic
1
2
3
4
5
6
7
8
750-630
-D
-D
-CL
-CL
+D
+D
+CL
+CL
0V_EX
24V
24V
0V
DC
DC
100nF
270pF
270pF
270pF
270pF
0V
+5V
0V
+5V
270pF
270pF
2k2
120R
2k2
Fig. 2.1.1-2: SSI Transmitter Interface 750-630 g063001e

10 •750-630 (/xxx-xxx) [SSI Transmitter Interface]
Technical Data
WAGO-I/O-SYSTEM 750
I/O Modules
2.1.1.6 Technical Data
Module Specific Data
Transmitter connection Inputs: + D, -D, Outputs: +CL, -CL
Current consumption typ. (internal) 85 mA
Voltage via power jumper contacts DC 24 V (-15 % ... +20 %)
Transmission rate 125 kHz (max. 1 MHz)
Serial Input max. 32 bit width (adjustable)
Signal output (+CL, -CL) differential signal (RS 422)
Signal input (+D, -D) differential signal (RS 422)
Code Gray / Bin
Internal bit width 1 x 32 bits (24 bit used, 8 bit reserved)
2 x 8 bits control/status (option)
Isolation 500 V (System/Supply)
Dimensions W x H* x L
* from upper edge of 35 DIN rail
12 mm x 64 mm x 100 mm
Weight ca. 55 g
Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual)
CULUS (UL508)
CULUS (UL1604) Class I Div2 ABCD T4A
KEMA II 3 G EEx nA II T4
Conformity Marking
More Information
Detailed references to the approvals are listed in the document "Overview
Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM
ELECTRONICC Tools and Docs (Item-No.: 0888-0412)
or in the internet under:
www.wago.com !Documentation !WAGO-I/O-SYSTEM 750 !
System Description