3
2018148_a•en•2017-04-01 We reserve the right to make technical changes
Learning/recalling the comfort positions
A comfort position can be saved for the receivers in the
network (e.g. awning half extended). The awning can be
automatically moved to this comfort position at the press
of a button.
Button/
display
Action/result
WMS Hand-held transmitter plus
To learn in the comfort position:
Move your product to the position that is
to be saved as the comfort position (see
"Operating the products").
Hold down the comfort button for 5
seconds until the transmission LED
lights up.
The transmission LED
indicates that
transmission is occurring:
2 s GREEN:
The comfort position is saved.
2 s RED: The command was not con-
firmed (e.g. receiver outside
of transmission range);
repeat the procedure.
To recall a comfort position:
Select the channel using the
button.
Briefly press the comfort button .
The transmission LED flashes green.
The comfort position for the selected prod-
uct is restored automatically.
OTICEN If a product is already in the comfort position
or if a comfort position has not been saved, the
selected product does not respond to briefly
pressing the comfort button :
OTICEN When the comfort position is not moved to cor-
rectly, the run time in the receiver must be ad-
justed with a WMS Central transmitter or a WMS
Hand-held transmitter (please see the operating
instructions of the respective receiver).
Switching the comfort control functions on/off
Button/
display
Action/result
WMS Hand-held transmitter plus
Select the channel using the
button.
Briefly press the control button on the
WMS Hand-held transmitter plus.
The transmission LED flashes green.
The transmission LED lights up:
GREEN: The control functions are
switched on in all receivers.
RED:
Not all receivers could be
reached; switch the control
functions OFF and ON again
(or ON and OFF).
The A LED lights up:
GREEN: Switch on the control func-
tions.
RED: Switch off the control func-
tions.
The WMS Hand-held transmitter plus always remembers the
command sent last. When the control button
is pressed
again, the WMS Hand-held transmitter plus sends the op-
posite command (ON - OFF - ON -...).
Commissioning
Videos for commissioning can be found at:
http://www.warema.de/inbetriebnahme
funksysteme
We recommend commissioning using the
PC software WMS studio!
Insert the supplied batteries into the battery compart-
ment as described in the "Maintenance and cleaning"
section. The device is ready for operation.
OTICEN Before WMS receivers can be operated via the
WMS Hand-held transmitter plus, the relevant
receiver must be included as a device in a
radio network.
The application examples below, using the example of the
WMS Hand-held transmitter plus, are intended to make it
easier for you to perform the procedures you require.
Example 1:
The existing unit with a WMS Hand-held trans-
mitter is expanded to include a WMS Hand-held
transmitter plus
Step 1
Add the WMS Hand-held transmitter plus to the existing
network
Button/
display Action/result
Wake up the WMS Hand-held transmitter
plus with the STOP button .
Wake up the (large) WMS Hand-held trans-
mitter with any product button.
Press the learn button on the large WMS
Hand-held transmitter for approx. 5s.
+ lights up green; the transmission LED
flashes. For several seconds, the hand-
held transmitter scans the operating range
for devices.
E.g. When the scanning procedure is complet-
ed, the located devices are displayed in
the upper row of LEDs (here, for example,
2 receivers).
RED: New device
GREEN: The device already belongs to
the network.
Devices that already belong to a different
network are not located during scanning.
Select a device using the arrow buttons.
(Briefly press to check which device is
currently selected. The product waves.)
E.g. The LED of the selected device flashes on
the large WMS Hand-held transmitter.
Press the STOP button on the large
WMS Hand-held transmitter to add the
WMS Hand-held transmitter plus to the
network.
E.g. The LED of the selected device flashes
green. The WMS Hand-held transmitter
plus has been successfully learned into
the network.
You can now add additional scanned products in the
same manner.
Briefly press the learn button to leave the
learn mode.
