Panasonic AK-HRP200G User manual

Model No. AK-HRP200G
Operating Instructions
<Operations and Settings>
Remote Operation Panel
VQT4S52A-6 (E)
zHow the operating instructions are organized
• Basics:
This manual describes how to connect the unit to the required equipment and set it up.
Before installing the unit, be sure to read the <Basics> manual to ensure that you know how to install
it correctly.
• Operations and Settings (this manual)
Operations and Settings describe how to operate and set up the unit.
W1012MN6117 -PS
ENGLISH
Before operating this product, please read the instructions carefully and save this manual for future use.

2 3

 
 
Operation modes ................................................................................. 4
Switching between serial connection mode and IP connection mode ... 4
Operation mode setting procedure ...................................................... 5
 
Setup mode.......................................................................................... 6
 
1 Set camera number ........................................................................ 10
2 Save scene file to/load scene file from memory card ..................... 10
3 Saving user files to/loading user files from memory card ............... 11
4 Save lens file to/load lens file from memory card ........................... 12
5 Save ROP configuration file to/load ROP configuration file from
memory card .................................................................................. 13
6 Format memory card....................................................................... 13
7 Select/set flare and pedestal........................................................... 14
8 Set buzzer (beep/call tone) ............................................................. 14
9 Display brightness setting (LED/7-segment display) ...................... 14
10 Set IP address .............................................................................. 15
11 Set subnet mask ........................................................................... 15
12 Set default gateway ...................................................................... 16
13 Set port ......................................................................................... 16
14 Save/load remote camera configuration file.................................. 16
15 Set serial ....................................................................................... 17
16 Initialize settings............................................................................ 18
17 Confirm version ............................................................................. 18
18 Save unit data to memory card ..................................................... 18
19 Software upgrade.......................................................................... 18
20 Set tally number ............................................................................ 19
21 Set tally output .............................................................................. 19
22 Syncro shutter display setting ...................................................... 19
23 Tally control setting (for camera recorder only) ............................ 19
Error messages in setup mode .......................................................... 20
 
ROP menus that can be operated on the unit.................................... 21
Operating ROP menus....................................................................... 21
 
SHADING(WHITE) ............................................................................. 23
PEDESTAL/FLARE/GAIN .................................................................. 23
GAMMA/BLACK. GAMMA ................................................................. 24
CINEMA GAMMA .............................................................................. 25
KNEE/WHITE CLIP ............................................................................ 25
COLOR CONTROL ............................................................................ 26
MATRIX (1/2) ..................................................................................... 26
MATRIX (2/2) ..................................................................................... 26
HD DTL/SKIN DTL (1/2) .................................................................... 27
HD DTL/SKIN DTL (2/2) .................................................................... 27
SD DETAIL ........................................................................................ 28
SYSTEM (1/2) .................................................................................... 28
SYSTEM (2/2) .................................................................................... 29
FUNCTION ........................................................................................ 30
LENS FILE/EDIT (1/2) ....................................................................... 30
LENS FILE/EDIT (2/2) ....................................................................... 31
ROP SD CARD .................................................................................. 31
 
IP setting procedure ........................................................................... 32
How to Start the Software .................................................................. 33
Connecting the devices...................................................................... 33
Connecting and setting the personal computer ................................. 33
Setting the IP addresses of the devices............................................. 33
Configuring various settings of the ROP ............................................ 33
 
Setting IP addresses of devices......................................................... 34
 
Register the unit in the ROP Setup Software [ROP List]. .................. 35
Configuring the Unit Settings [Configuration] ..................................... 36
Making Camera Connection Settings [Camera List] .......................... 36
Set up user authentication [User Auth.] ............................................. 39
 
 
• SDHC logo is a trademark of SD-3C, LLC.
• Other company names and product names appearing in this manual are the registered trademarks or trademarks of their respective companies.
 
It is prohibited to transfer, copy, disassemble, decompile, and reverse engineer the software included with the unit, as well as export it in violation of
the export laws.
 
The following abbreviations are used in this manual.
• SD memory cards and SDHC memory cards are both referred to as “memory cards”. They are referred to individually in descriptions in which each
of them is discussed separately.
• Personal computers are referred to as “computers.”
• A studio handy camera is referred to as a camera in this manual.
• A camera control unit is referred to as a CCU in this manual.
• A remote operation panel is referred to as an ROP in this manual.
• A master setup unit is referred to as an MSU in this manual.
• The memory card camera recorder is referred to as the camera recorder in this manual.
 
• Illustrations of the unit and screens may appear different from the actual unit and screens.

2
3

 
This unit is a remote operation panel for controlling a studio handy
camera (AK-HC3800/AK-HC3500A) and a camera control unit
(AK-HCU200/AK-HCU355A).
Use a dedicated optical fiber cable to connect a studio handy camera
to a camera control unit and use an ROP cable or IP connection to
connect this unit to the camera control unit. Furthermore, a remote
camera or camera recorder can be connected via a serial connection
or IP connection.
When IP connections are used, up to 19 studio handy cameras,
remote cameras, and camera recorders can be controlled.
 
Memory cards used with the unit should conform to SD or SDHC
standards.
Be sure to use the unit to format memory cards.
Memory cards with the following capacity can be used with the unit.
SDXC memory cards are not supported.
SD memory cards: 8 MB to 2 GB
SDHC memory cards: 4 GB to 32 GB
For the latest information not described in the Operating Instructions,
refer to the following website.
http://pro-av.panasonic.net/
Observe the following points when using and storing this unit.
• Avoid high temperature and humidity.
• Avoid water droplets.
• Avoid static electricity.
 
You can obtain upgrade software from Service and Support on the
following website.
http://pro-av.panasonic.net/
For the upgrade procedure, refer to the instructions included with the
download file.
 
Software upgrades will also become necessary for the peripheral
equipment that is connected to this unit (cameras or CCUs).
For details, consult your supplier.
 
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY
PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,
DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR
EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE
USER;
(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION
OF THE PRODUCT BY THE USER;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES
ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE
INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD PARTY;
(6) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE;
 
Scene file Scene files are mainly used by video
engineers (VE) to create the required image
characteristics.
Reference file The term reference file is a generic term for
user files and factory files.
User file A user file is system setting data (reference
file) composed of scene files and operation
data. The user can record user files.
Factory file A file that contains camera settings that were
stored at the factory.
Lens file Data for correcting specific lens
characteristics that are used by video
engineers (VE).
ROP configuration file ROP specific setting data.
Remote camera
configuration file
Remote camera setting data. It is acquired
from a remote camera via IP.

4
5


The unit has a serial connection mode and an IP connection mode.
Serial connection mode The operation mode for use with a single CCU, remote camera, or camera recorder connected via a serial connection.
Only one CCU, remote camera, or camera recorder can be controlled. (The camera switching operation is not possible.)
The mode set at the time of shipment is serial connection mode.
IP connection mode The operation mode for use with CCUs, remote cameras and camera recorders used with IP connections.
A serial connection to a single CCU, remote camera, or camera recorder can be used at the same time as the IP
connections.
Up to 19 CCUs, remote cameras or camera recorders can be controlled. (The camera switching operation is possible.)
Use ROP Setup Software to configure various settings.

 





  
Serial
connection
mode
Configuration with CCU connected with a
serial connection

(1 device only)
(Connection not
possible)
(Connection not
possible)
(Do not connect) Not required
Configuration with remote camera
connected with a serial connection
(Connection not
possible)

(1 device only)
(Connection not
possible)
(Do not connect)
Configuration with camera recorder
connected with a serial connection
(Connection not
possible)
(Connection not
possible)

(1 device only)
(Do not connect)
IP
connection
mode
Configuration with IP connections only (Do not connect) (Do not connect) (Do not connect) 
(Total of up to 19
devices)
Required
Configuration with a combination of a
CCU connected with a serial connection
and CCUs and remote cameras
connected with IP connections

(1 device only)
(Connection not
possible)
(Connection not
possible)

(Total of up to 18
devices)
Configuration with a combination of a
remote camera connected with a serial
connection and CCUs and remote
cameras connected with IP connections
(Connection not
possible)

(1 device only)
(Connection not
possible)

(Total of up to 18
devices)
Configuration with camera recorder
connected with a combination of a serial
connection and IP connection
(Connection not
possible)
(Connection not
possible)

(1 device only)

(Total of up to 18
devices)

Switch between serial connection mode and IP connection mode in ROP Setup Software. (→page 35)
When the settings are initialized (setup mode), the mode returns to serial connection mode (factory default state).
Serial connection mode
Possible to connect to a CCU, remote camera,
or camera recorder with a serial connection.
・An IP connection is not possible.
・
You can set whether the control target is a
CCU or remote camera in setup mode.
IP connection mode
Possible to connect to CCUs, remote cameras
and camera recorders with IP connections.
・IP connections can be used in combination
with a serial connection.
・You need to use ROP Setup Software to
configure various settings.
Switch to IP connection mode
in ROP Setup Software*1.
Return the operation mode to
serial connection mode in
ROP Setup Software*2.
Factory default state
Turn the power on.
Initializing the settings (setup mode) returns the mode to serial
connection mode (factory default state).
In IP connection mode, you can switch control to any of up to 19 CCUs, remote cameras or camera recorders during operation.
In serial connection mode, you can only control one CCU, remote camera, or camera recorder during operation.
*1 When serial connection mode
If an ROP configuration file that was saved to a memory card in IP connection mode is loaded, the operation mode becomes IP connection mode.
*2 When IP connection mode
If an ROP configuration file that was saved to a memory card in serial connection mode is loaded, the operation mode becomes serial connection
mode.

4 5
 

In the factory default state, connect the CCU, remote camera or camera recorder to the unit and then set the operation mode.
In the factory default state, connect the CCU, remote camera or camera recorder to the unit
(for details, refer to Operating Instructions <Basics>).
Operation in IP connection modeOperation in serial connection mode
1. In Easy IP Setup Software,
set the IP addresses of the
CCUs and remote cameras
(→ page 33).
・
Set the IP address of the
camera recorder from the
menu on the unit.
3. Connect to the CCU and remote
cameras/camera recorders in IP
connection mode and then start
operation.
1. Select CCU in the serial
setting in setup mode
(→ page 17).
When connecting to a CCU
with a serial connection
2. Connect to the CCU in serial
connection mode and then
start operation.
When connecting to a remote
camera with a serial connection
1. Select remote camera in the
serial setting in setup mode
(→ page 17).
2. Connect to the remote camera
in serial connection mode and
then start operation.
When connecting to a camera
recorder with a serial connection
1. Select camera recorder in the
serial setting in setup mode
(→ page 17).
2. Connect to the camera
recorder in serial connection
mode and then start operation.
2. In ROP Setup Software, set the
remote camera configuration
file to assign to each camera
number (→ page 35).

z
Do not start Easy IP Setup Software and ROP Setup Software during operation.
The ROP will be disconnected, which in turn may cause a problem with operation.

6
7


Setup mode allows the user to make a variety of unit settings, and save and load scene files and user files.
Normal operation is unavailable during setup mode operation. ROP menu (REMOTE OPERATION MENU) operation is not available either.
 
Setup mode allows you to do any of the following.
The functions for camera recorder (serial connection) are identical to those for camera recorder (IP connection).
  

 

























1 Set camera number Sets a camera number. 
2 Save scene file to/
load scene file from
memory card
Saves the currently used scene
file to a memory card. It also
allows you to load a scene file
stored on a memory card.

3 Save user file to/
load user file from
memory card
Saves the currently used user
file to a memory card. It also
allows you to load a user file
stored on a memory card.

4 Save lens file to/
load lens file from
memory card
Saves the currently used lens
file to a memory card. It also
allows you to load a lens file
stored on a memory card.

5 Save ROP
configuration
file to/load ROP
configuration file
from memory card
Save a configuration file for
the unit to a memory card.
It also allows you to load a
configuration file for the unit
stored on a memory card.

6 Format memory
card
Formats a memory card 
7 Select/set flare and
pedestal
Selects the flare and pedestal
control function

8 Set buzzer (beep/
call tone)
Enables or disables the buzzer
or call tone.

9 Set display
brightness (LED/7-
segment display)
Sets the brightness of the panel
LED and 7-segment display.

10 Set IP address Sets the IP address of the unit 
11 Set subnet mask Sets the subnet mask of the unit. 
12 Set default gateway Sets the default gateway of the
unit.

13 Set port Sets the port of the unit. 
14 Save/load
remote camera
configuration file
Saves the data recorded by the
remote camera to a memory card.
It also allows you to load a camera
file stored on a memory card.

15 Set serial Switches between the CCU
serial, remote camera serial and
camera recorder serial when the
unit is in serial connection mode.
 
16 Initialize settings Initializes unit settings. 
17 Confirm version Displays the version of the
software used by the unit.

18 Save unit data to
memory card
Saves unit data to a memory
card.

19 Upgrade software Upgrades the software used by
the unit.

20 Set tally number Sets the camera number to
assign to tally input.
   
21 Set tally output Enables or disables tally output.    
22 Syncro shutter
display setting
When using syncro shutter,
switches between SEC and
DEG display.

23 Tally control setting Specifies whether tally control is
performed via panel operations
or preview terminal inputs.

The setup mode menu differs depending on the operation mode and connection configuration.

6 7
 
 
Setup mode differs from normal operating modes. Use the steps below
to open setup mode.


If the IRIS display is not lit, press the selected <DISPLAY SELECT>
button to select IRIS.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
IRIS display
Use the steps below to open setup mode when the power is on, but a
camera or CCU is not connected.



This opens setup mode and Menu No. 1 (camera number setting) is
displayed.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
SCENE 4 STORE
SCENE 3
SCENE 2
SCENE/USER FILE
SCENE 1
USER 3
USER 2USER 1
SHIFT
 
To exit setup mode, hold down <EXIT> for two seconds. The unit returns
to normal operating mode.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
 
The buttons indicated in the figure below are available in setup mode.
No other buttons are available. All other LEDs stay off. (Except the
alarm display)
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
1
5
67 8
2 43






1→2→3→...→21→1→2→...





CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN

8
 
9
 
Setup mode is comprised of the menus and submenus listed in the table below.
   

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press <SELECT>to select a menu number. Press <SAVE/LOAD> to select a submenu. Use <UP> or <DOWN> to select a set value or
an operation.
Use <EXECUTE> to confirm an entry.
  

 
1Set camera number*1- - Camera number
(AK-HC3500A: 1 to 15)
(AK-HC3800: 1 to 19)
1
2 Save scene file to/load scene file
from memory card
ND Save to memory card Scene files (1 to 4) 1
CC Load from memory card Scene files (1 to 4) 1
3 Save user file to/load user file
from memory card
ND Save to memory card User files (1 to 3) 1
CC Load from memory card User files (1 to 3) 1
4 Save lens file to/load lens file
from memory card
ND Save to memory card Lens files (1 to 32) 1
CC Load from memory card Lens files (1 to 32) 1
5 Save ROP configuration file to/
load ROP configuration file from
memory card
ND Save to memory card - -
CC Load from memory card - -
6 Format memory card - - - -
7Select/set flare and pedestal*1- - FLARE/PED (FL/PE) FL
8Set buzzer (beep/Call)*1- - Enable/disable buzzer (on/off) on
9 Set display brightness (LED/7-
segment display)*1
ND LED 3 levels (bright/intermediate/low) Bright
CC 7-segment display 3 levels (bright/intermediate/low) Bright
10 Set IP address*1 *2ND Block 1 Display/set block 1
192.168.0.130
CC Block 2 Display/set block 2
SHT Block 3 Display/set block 3
SYNC Block 4 Display/set block 4
11 Set subnet mask*1 *2ND Block 1 Display/set block 1
255.255.255.0
CC Block 2 Display/set block 2
SHT Block 3 Display/set block 3
SYNC Block 4 Display/set block 4
12 Set default gateway*1 *2ND Block 1 Display/set block 1
192.168.0.1
CC Block 2 Display/set block 2
SHT Block 3 Display/set block 3
SYNC Block 4 Display/set block 4
13 Set port*1 *2ND 3 digits Display/set 3 digits 35200
CC 2 digits Display/set 2 digits
14 Save/load remote camera
configuration file
ND Save to memory card Camera files (1 to 19) 1
CC Load from memory card
15 Set serial*1- - CCU serial (1)
Remote camera serial (2)
Camera recorder serial (3)
1
16 Initialize settings - - - -
17 Confirm version ND Display version No (first digits) Displays the first 3 digits -
CC Version No (middle digits) Displays the middle 2 digits -
SHT Version No (last digits) Displays the last 3 digits -
18 Save unit data to memory card - - - -
19 Upgrade software - - - -
20 Set tally number*1- - Tally numbers (1 to 19, --) 1
21 Set tally output*1- - Tally link (on/off) off
22 Syncro shutter display setting - - SEC/DEG(SEC/dEG) SEC
23 Tally control setting*3- - 1 (panel operation) / 2 (preview terminal) 1
*1 These functions are initialized when you perform settings initialization.
*2 If you change a setting, restart the unit when you exit setup mode.
*3 This setting is enabled when the camera recorder is connected.

8
9
 
 
In setup mode, the following files are saved to or loaded from a memory card by the unit. The fixed file names assigned by the unit must not be changed
on a computer. If the file names are changed, they can no longer be processed by the unit.
 
Scene file SCENE1.BIN to SCENE4.BIN
User file USER1.BIN to USER3.BIN
Lens file LENS01.BIN to LENS32.BIN
ROP configuration file ROP_OPE.BIN
Unit data file ROP_INFO.BIN
Remote camera configuration files CAM01.BIN to CAM19.BIN

• The scene files, user files, and lens files that can be handled by the unit are the data of AK-HC3800 only. The data of AK-HC3500A and remote
cameras cannot be handled.
• Files that have been saved to a memory card with an MSU cannot be loaded by the unit.
Files that have been saved to a memory card with the unit cannot be loaded by an MSU.
• A Remote camera configuration file can be saved and loaded only when the remote camera and unit are connected with an IP connection.
• The save date and time (time stamp) format of a file saved to a memory card with the unit is fixed to “2099/1/1 00:00.”

10
11





CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirm the camera number
Press to select the camera number


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
To select camera number 2
• Camera numbers become available after exiting setup mode.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

For AK-HC3500A, the camera numbers 1 to 15 are valid. When
connecting to AK-HC3500A, do not set a camera number to 16 or
above.

Current operating status data is saved as a scene file to the memory
card.

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
ND CC
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirm
Select file number,
Select y (Select)/
n (Cancel)
Press to save/load
Save file indication
Load file indication

Before switching to setup mode, open the scene file you wish to save
with the SCENE/USER FILE select buttons. (For details on how to open
a scene file, refer to Operating Instructions <Basics>.)

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
To save a file to file no. 2 on the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a scene file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 20)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

Scene file data loaded from the memory card is returned to the
operating status. (It is not returned to scene files 1 to 4. To return the
data to scene files 1 to 4, exit setup mode and store the data in one of
scene files 1 to 4. For details, refer to <Basics>, the instruction manual.)

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC

10 11
 



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
CC
To load file no. 2 from the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 20)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select file number,
Select y (Select)/
n (Cancel)
Save file indication
Load file indication
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirmPress to save/load

Before switching to setup mode, open the user file you wish to save with
the SCENE/USER FILE select buttons. (For details on how to open a
user file, refer to Operating Instructions <Basics>.)
Current operating status data is saved as a user file to the memory card.

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
To save a file to file no. 2 on the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a user file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 20)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

User file data loaded from the memory card is returned to the operating
status. (It is not returned to user files 1 to 3. To return the data to user
files 1 to 3, exit setup mode and store the data in one of user files 1 to
3. For details, refer to Operating Instructions <Basics>, the instruction
manual.)

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
To load file no. 2 from the memory card

12
 
13


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 20)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select file number,
Select y (Select)/
n (Cancel)
Save file indication
Load file indication
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirmPress to save/load

Before switching to setup mode, open the lens file you wish to save with
the ROP menu. (→page 31)

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
To save a file to file no. 2 on the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a lens file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 20)
• [E04] is displayed when the lens file is off.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


• Each press of <SAVE/LOAD> toggles it between [ND] (Save) and
[CC] (Load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
To load file no. 2 from the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
(→page 20)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

12
13
 



CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select y (Select)/
n (Cancel)
Save file indication
Load file indication
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirmPress to save/load


• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when an ROP configuration file with the same
name as the one you are attempting to save already exists on the
memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 20)

• The data set in setup mode and ROP Setup Software is saved to
the memory card.
• The following data is not saved.
- IP address of the unit
- Subnet mask of the unit
- Default gateway of the unit
- Port setting of the unit
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

When the ROP configuration file is loaded, the setting data stored on
the memory card is loaded. If the operation mode of the unit and the
operation mode in the memory card differ, the operation mode changes
to the operation mode saved in the memory card.

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC


• The file is loaded from the memory card and [Fin] appears when
loading ends. A few seconds later, the unit is restarted.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel loading, select [n] and press <EXECUTE>.
• [E02] is displayed if the load operation from the memory card fails.
(→page 20)
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.


CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select y (Format)/n (Cancel)
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirm


• Card formatting starts.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel formatting, select [n] and press <EXECUTE>.
• When the formatting ends, [Fin] appears.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

Be sure to execute a format after confirming the data because any data
that is deleted by the format cannot be recovered.

14
 
15


CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select FL (Flare)/PE (Pedestal)
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirm



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select on/off
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirm


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Adjust brightness
LED display brightness
7-segment display brightness
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirmLED/7-segment display switch



• Each press of <SAVE/LOAD> toggles between [ND] (LED display
brightness) and [CC] (7-segment display brightness).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.



• Each press of <SAVE/LOAD> toggles between [ND] (LED display
brightness) and [CC] (7-segment display brightness).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC

14
15
 



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


• Block 1 of the IP address appears.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the
menu number
Press to select
the IP address
Press to switch the block Press to confirm
Press to exit setup mode (hold down)
Display/set block 1
Display/set block 2
Display/set block 3
Display/set block 4

• The display changes in the order of block 1, block 2, block 3, and
block 4.
• When changing the IP address, press <UP> or <DOWN> to change
the setting for each block.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC

• Pressing <SHUTTER> while block 4 is displayed confirms the
setting.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the IP address setting value has been changed, the unit will
restart automatically when you exit setup mode. If the setting value
has not been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.


• Block 1 of the subnet mask appears.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Display/set block 1
Display/set block 2
Display/set block 3
Display/set block 4
Press to select
the subnet mask
Press to select the
menu number
Press to switch the block Press to confirm
Press to exit setup mode (hold down)

ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• The display changes in the order of block 1, block 2, block 3, and
block 4.
• When changing the subnet mask, press <UP> or <DOWN> to
change the setting for each block.

ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• Pressing <SHUTTER> while block 4 is displayed confirms the
setting.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the subnet mask setting value has been changed, the unit will restart
automatically when you exit setup mode. If the setting value has not
been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.

16
 
17


• Block 1 of the default gateway appears.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the
menu number
Press to select the
default gateway
Press to switch the block Press to confirm
Press to exit setup mode (hold down)
Display/set block 1
Display/set block 2
Display/set block 3
Display/set block 4

• The display changes in the order of block 1, block 2, block 3, and
block 4.
• When changing the default gateway, press <UP> or <DOWN> to
change the setting for each block.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC


• Pressing <SHUTTER> while block 4 is displayed confirms the
setting.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the default gateway setting value has been changed, the unit will
restart automatically when you exit setup mode. If the setting value
has not been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.
 
192. 168. 0. 130
Block 1 Block 2 Block 3 Block 4
For the IP address, you can set a value within the following ranges.
Block 1 1 to 223
Block 2 0 to 255
Block 3 0 to 255
Block 4 1 to 254
However, “127.0.0.1” cannot be set even though it is within the above
ranges.
For the subnet mask, you can set a value within the following ranges.
Block 1 0 to 255
Block 2 0 to 255
Block 3 0 to 255
Block 4 0 to 255
However, “0.0.0.0” and “127.0.0.1” cannot be set even though it is
within the above ranges.
For the default gateway, you can set a value within the following
ranges.
Block 1 0 to 255
Block 2 0 to 255
Block 3 0 to 255
Block 4 0 to 255


• The 3 digits of the port number appear.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
First 3 digits
Last 2 digits
Press to select the
menu number
Press to select
the port
Press to switch the block Press to confirm
Press to exit setup mode (hold down)

• The display changes to the next 2 digits.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• Press <UP> or <DOWN> to change the setting for each block.
• Press <SHUTTER> to confirm the setting.
• A value within the range of 35200 to 35599 can be set for the port
number.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the port number setting value has been changed, the unit will restart
automatically when you exit setup mode. If the setting value has not
been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.

The data recorded by the remote camera can be saved to a memory
card.

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the
menu number
Select y (Execute)/
n (Cancel)
Save/load selection confirmation
Save indication
Load indication
Press to confirm
Press to exit setup mode (hold down)

16
17
 


• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (Load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
When saving to file number 2 on the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a remote camera configuration file with the
same name as the one you are attempting to save already exists on
the memory card. To overwrite the file, press <UP> or <DOWN> to
select [y] and press <EXECUTE>.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.


Remote camera configuration file data loaded from the memory card is
returned to the operating status.

Each press of <SAVE/LOAD> toggles between [ND] (Save) and [CC]
(Load).
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC



ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
When loading file number 2 on the memory card


• Do not remove a memory card that is being accessed.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

Press <SELECT> to select menu number [15].
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the
menu number
1 (Select CCU serial)/
2 (Select remote camera serial)
Press to confirm
Press to exit setup mode (hold down)

Press <UP> or <DOWN> to select [1] and press <EXECUTE> to confirm
the selection.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• After the selection is confirmed, the unit restarts automatically.

Press <UP> or <DOWN> to select [2] and press <EXECUTE> to confirm
the selection.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• After the selection is confirmed, the unit restarts automatically.

Press <UP> or <DOWN> to select [3] and press <EXECUTE> to confirm
the selection.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• After the selection is confirmed, the unit restarts automatically.

18
 
19


When settings are initialized, the unit is automatically restarted.For
details on what settings are initialized, refer to page 8

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select y (Initialize)/n (Cancel)
Press to select the
menu number
Press to exit setup mode
(hold down)
Press to confirm


• After confirmation, unit settings are initialized and it is automatically
restarted.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To cancel initializing, select [n] and press <EXECUTE>.


• The version information is displayed.
• Press <SAVE/LOAD> to show the 8-digit version number split up in 3,
2 and 3 digits.
CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the menu numberPress to switch display
digits
Display digit indication (first 3 digits)
Display digit indication (middle 2 digit)
Display digit indication (last 3 digits)
Press to exit setup mode (hold down)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

This function is used by the manufacturer during maintenance.

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Press to select the
menu number
Press to confirm
Select y (Save)/n (Cancel)
Press to exit setup mode
(hold down)


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a unit data file with the same name as the
one you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>. (→page 20)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

For details on software upgrades, refer to “Software upgrades” (→page
3).

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Select y (Upgrade)
Press to select the
menu number
Press to confirm
Press to exit setup mode
(hold down)

18
19
 


• Upgrading starts.
ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• When the upgrade ends, [Fin] appears and the unit restarts
automatically.

If the upgrade fails for some reason, <SHIFT> may start to flash after
the restart. If this happens, perform the upgrade process again.

Set the camera number to assign to tally input.

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Flashes
Press to select the
menu number
Press to select
the camera number
Press to confirm
Press to exit setup mode (hold down)


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

Set the sending of tally information from the unit to remote cameras.

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Flashes
Press to select the
menu number
Press to select the
camera number
Press to confirm
Press to exit setup mode (hold down)


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.

Sets whether a camera recorder's syncro shutter speed is displayed in
seconds (SEC) or in iris degrees (DEG).

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Flashes
Press to select the
menu number
Select SEC (seconds) or
DEG (aperture angle)
Press to confirm
Press to exit setup mode (hold down)


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC

Specifies whether tally control is performed via panel operations or
preview terminal inputs.

CAMERA
No.
DATA
SET
DISPLAY SELECT
UP
DOWN
SET UP
ND/CC M.GAIN/M.PED SHUTTER
ND
M.GAIN
IRIS
M.PED 10-19
CC SHT SYNC
SELECT
EXECUTEEXIT SAVE/LOAD
SHIFT
+
UP+DOWN
Flashes
Press to select the
menu number
Select 1 (panel operation)/
2 (preview terminal)
Press to confirm
Press to exit setup mode (hold down)

20
 
21


ND
M.GAIN
IRIS
M.PED
CC SHT SYNC
• To make other settings, press <SELECT> to select a menu number.

 
 A file with the same name already exists. Select [y]
to overwrite.
 An error occurred on the memory card.
• Check if a file exists.
• Check if the memory card is write protected.
•
Check if there is any free space left on the memory card.
• Check if an SDXC card is being used.
• The file format of the memory card may not be
correct.
• There may be a memory card format abnormality.
 A memory card has not been inserted.
 • A communication error occurred. Check the
connected equipment.
• The lens file is off.
• There are not connections with cameras and CCUs
and the control privileges are disabled. (For details
on control privileges, refer to Operating Instructions
<Basics>.)
 An error occurred. Start over from the beginning.
 
[E01] is displayed when a file with the same name as the one you are
attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and press
<EXECUTE>.
 
Press <EXECUTE> to close the error message. Then perform the
operation again.