WAREMA WMS Wall-mounted transmitter basic User manual

Operating- and installation instructions
WAREMA Mobile System
WMS Wall-mounted transmitter basic
Keep for future use!
Valid from 01. October 2019
2018114_b•en•2019-10-01 Technische Änderungen behalten wir uns vor 1
AUTIONC
Never activate buttons on your WMS Wall-
mounted transmitter basic arbitrarily without
visual contact to the sun shading product.
Children must not play with this product –
remote controls or transmitters must not get
into the hands of children!
To ensure trouble-free operation of the unit,
 Read these instructions carefully,
 Learn the WMS wall-mounted transmitter basic into the
receivers
 Check that the system is functioning correctly.
Commissioning
You can find instruction videos on our
YouTube channel at:
http://www.youtube.com/user/SonnenLichtManager/videos
We recommend commissioning using the
WMS studio pro PC software.
 The supplied battery is already inserted and the device
is ready to operate.
OTICEN To spare the button cell of the WMS Wall-
mounted transmitter basic during learning,
the waking time of the WMS Wall-mounted
transmitter basic was reduced to 1minute. If
your device stops responding, simply wake it
up by pressing the Stop button, for example.
Installation
The WMS Wall-mounted transmitter basic consists of a
mounting frame and control.
 Attach the mounting frame to the wall using the
countersunk screws and dowels included.
 Position the central frame/plate of the switch program
you require.
 Clip on the wall-mounted transmitter.
Clipping the wall-mounted transmitter and central
frame/plate into the available snap-in latches will hold
them in place on the mounting frame.
OTICEN Only use countersunk screws so that the
screws are flush with the mounting frame and
the WMS Wall-mounted transmitter basic can
be securely clipped on.
OTICEN When planning the installation location, be
sure to allow enough space for the central
frame/plate that you require for your particular
installation.
The central frame/plate can be ordered as an
optional accessory if needed.
General information
Fig. 1 WMS Wall-mounted transmitter basic
The WMS Wall-mounted transmitter basic is used for the
remote control of WAREMA WMS receivers. The receivers
send a confirmation of the received commands, and the
wall-mounted transmitter indicates that it received the
confirmation.
The WMS Wall-mounted transmitter basic is a 1-channel
transmitter and supports five different product types
(awning, roller shutter, external venetian blind, window, light).
Only one receiver or a group of receivers of the same
product type can be actuated at any one time.
The comfort control functions can be switched on and off
via the WMS Wall-mounted transmitter basic.
Comfort positions can be saved at the press of a button.
If a control function is preventing operation of the product
(e.g. a wind alarm), this is also displayed on the WMS
Wall-mounted transmitter basic.
The transmitter is compatible with:
Additional information can be found at:
http://www.warema.de
works with
Intended use
The WMS wall-mounted transmitter basic is an electronic
device developed to control WMS receivers. The approval
of the manufacturer must be obtained for uses outside of
the purposes listed in these instructions.
Safety instructions
AUTIONC
The WMS Wall-mounted transmitter basic is
for indoor use only. It is not water-proof.

2018114_b•en•2019-10-01We reserve the right to carry out improvements.
2

Fig. 2 Mounting structure for the WMS Wall-mounted
transmitter
 WMS Wall-mounted transmitter basic (included in the
scope of delivery),
 Central frame/plate (on-site or can be ordered as an
optional accessory),
 Switch program frame (on-site or can be ordered as an
optional accessory),
 Mounting frame (included in the scope of delivery).
Operating elements and displays






Fig. 3 Operating panel of WMS Wall-mounted transmitter basic
(front)
Pos. Fig. Function
Control function on/off button
Switch on and off the comfort control functions of
the receivers that were learned in.
Control function LED with two functions
When you press the control mode button
the LED only shows the transmission of an
"On" control function command. When an "OFF"
control function command is sent, the LED
does not light up.
If operation is blocked on your WMS Wall-
mounted transmitter basic, for example due to
a wind alarm, this LED flashes red. (The wind
alarm keeps your sun shading systems safe.
When the set wind speed limit is exceeded, the
blinds are retracted and manual operation is
blocked during this time.)
Pos. Fig. Function

+
The control function LED and transmission
LED flash
ORANGE: `WMS Wall-mounted transmitter basic
is in its factory state (does not belong
to a network, still needs to be learned
in).
OTICEN If the two buttons flash red, you
pressed the button for too long
and you are now in the "Reset
hand-held transmitter" mode. To
leave this mode, press the learn
button briefly .
The transmission LED flashes
GREEN: The WMS Wall-mounted transmitter
basic is transmitting.
RED: The WMS Wall-mounted transmitter
basic did not receive a response from
the receiver.
ORANGE: Change the batteries.
UP/STOP/DOWN buttons
Send move or switch commands to the selected
receiver. If the WMS Wall-mounted transmitter
basic is in the info or learn mode, the buttons can
be used to change or store settings.
Comfort button
This button can be used to store and call up
comfort positions.
Operating elements on the back
C
R
2
0
3
2



Fig. 4 Back of the WMS Wall-mounted transmitter basic
Pos. Fig. Function
Learn button
Activates or closes the learn mode of the WMS
Wall-mounted transmitter basic
L LED
Indicates that the WMS Wall-mounted transmitter
basic is in learn mode (lights up green)
Battery
The WMS Wall-mounted transmitter basic requires
a coin cell CR2032 battery

3
2018114_b•en•2019-10-01 We reserve the right to carry out improvements.
Operation
Button/
display Action/result
To learn in the comfort position:
 Operate the selected product using the
UP/STOP/DOWN buttons.
 The operating instructions of the
respective receiver describe which
operating options are available to you (e.g.
UP=ON, DOWN=OFF, STOP=switch).
The transmission LED indicates the
transmission status:
Flashes GREEN: WMS Wall-mounted
transmitter basic is transmitting,
then:
Lights up GREEN for 2s:
The receiver has confirmed the
command.
Lights up RED for 2s:
The command has not been
confirmed (e.g. the receiver
is outside of the transmission
range), or the WMS Wall-
mounted transmitter was added
to the network but a channel
has not yet been copied
onto the WMS Wall-mounted
transmitter basic.
Lights up GREEN for 2s + control symbol
is red:
The receiver confirms the
command, but does not execute
it because of the displayed
control function (e.g. the awning
is not extended because the
wind alarm is active).
The transmission LED indicates the
transmission status:
Lights up RED for 2s: The WMS Wall-
mounted transmitter was added to the
network but a receiver has not yet been
assigned.
Learning/recalling the comfort positions
A comfort position can be stored for the receivers in the
network (e.g. awning half extended). The awning can be
automatically moved to this comfort position at the press
of a button.
Button/
display Action/result
To learn in the comfort position:
 "Move your product to the position that is
to be stored as the comfort position (see
"Operating the products").
 Hold down the comfort button for 5
seconds until the transmission LED
lights up.
Button/
display Action/result
The transmission LED indicates the
transmission status:
2s GREEN: The comfort position is
stored.
2s RED: The command was not
confirmed (e.g. receiver
outside of transmission
range); repeat the
procedure.
To recall a comfort position:
 Briefly press the comfort button .
The transmission LED flashes green.
The comfort position for the selected
product is restored automatically.
OTICEN If a product is already in the comfort position or
if a comfort position has not been stored, the
selected product does not respond to pressing
of the comfort button :
OTICEN When the comfort position is not moved to
correctly, the run time in the receiver must be
adjusted with a WMS Central transmitter or a
WMS Hand-held transmitter (please see the
operating instructions of the respective receiver).
Switching on/off the comfort control functions
Button/
display Action/result
 Press the control button .
The transmission LED flashes green.
The transmission LED lights up:
GREEN: The control functions are
switched on in all receivers.
RED: Not all receivers could be
reached; switch the control
functions OFF and ON again (or
ON and OFF).
The A LED lights up:
GREEN: Switch on the control functions.
RED: Switch off the control functions.
The WMS Wall-mounted transmitter basic always remembers
the command last sent. When the control button is
pressed again, the WMS Wall-mounted transmitter basic
sends the opposite command (ON - OFF - ON -...).
OTICEN Before WMS receivers can be operated via a
WMS Wall-mounted transmitter basic, the WMS
Wall-mounted transmitter basic or the receiver
must be included as a device in a radio network.
OTICEN If you purchased the WMS Wall-mounted
transmitter basic separately, we recommend the
"WMS studio pro" PC software in combination
with WMS Stick for commissioning.
OTICEN If the WMS Wall-mounted transmitter basic is
still in its delivered state (no products have
been learned in yet), it is available for 1minute
after any button is pressed.
OTICEN When the [DOWN] function button is pressed
again while the sun shading product is being
lowered, it always moves to 100% (lower limit
position) and the “Position DOWN” value is
ignored.

2018114_b•en•2019-10-01We reserve the right to carry out improvements.
4
The application examples below are intended to make it
easier for you to perform the procedures you require.
Example 1:
The existing system with a WMS Hand-held
transmitter comfort is expanded to include a
WMS Wall-mounted transmitter basic
Step 1:
Add the WMS Wall-mounted transmitter basic to the
existing network
Button/
display Action/result
 Wake up the WMS Wall-mounted
transmitter basic with the STOP button .
 Wake up the WMS Hand-held transmitter
comfort with any product button.
 Press the learn button on the large WMS
Hand-held transmitter comfort for approx.
5s.
+ lights up green; the transmission LED
flashes. For several seconds, the
hand-held transmitter scans the range for
devices.
E.g. When the scanning procedure is
completed, the located devices are
displayed in the upper row of LEDs (here,
for example, 2 receivers).
RED: New device
GREEN: The device already belongs to
the network.
Devices that already belong to a different
network are not located during scanning.
 Select a device using the arrow buttons.
(Briefly press to check which device is
currently selected. The product waves*.)
E.g. The LED of the selected device flashes
on the large WMS Hand-held transmitter
comfort.
 Press the STOP button on the large
WMS Hand-held transmitter comfort to add
the WMS Wall-mounted transmitter basic
to the network.
E.g. The LED of the selected device flashes
green. The WMS Wall-mounted transmitter
basic has been successfully learned into
the network.
You can now add additional scanned products in the
same manner.
 Briefly press the learn button to leave the
learn mode.
Step 2:
Copy a channel from a WMS Hand-held transmitter
comfort or a WMS Central transmitter to a WMS Wall-
mounted transmitter basic.
Button/
display Action/result
 Wake up the WMS Hand-held transmitter
comfort with any product button.
 Select the channel of the hand-held
transmitter that you wish to copy.
 Briefly press the learn button on the large
WMS Hand-held transmitter comfort.
The L LED lights up green.
Button/
display Action/result
 Briefly press the learn button on the
TARGET TRANSMITTER, the WMS Wall-
mounted transmitter basic in this case.
The L LED lights up green.
The transmission LED on the WMS
Wall-mounted transmitter basic flashes.
GREEN During the transmission of data
from the WMS hand-held transmitter
comfort / Central transmitter to the target
transmitter (WMS Wall-mounted transmitter
basic); this ends with
GREEN Lights up continuously for
2 seconds, transmission
successful
RED Light up continuously for
2 seconds, error during
transmission
The L LED on the WMS Wall-mounted
transmitter basic goes out.
* The product responds with short movements or
by lighting up briefly and in this way indicates that it
received the sent command.
Example 2:
The existing system with a WMS Central
transmitter is expanded to include a WMS Wall-
mounted transmitter basic
Step 1:
Add the WMS Wall-mounted transmitter basic to the
existing network with a WMS Central transmitter
 Wake up the WMS Wall-mounted transmitter basic
 Select the "Learn in/out hand-held transmitter/
central control unit" menu item on your WMS Central
transmitter under:
Main menu
 System
 Commissioning (logged in as specialist partner)
 Learn in/out hand-held transmitter/central transmitter
 Confirm the selected menu item with 
The control function LED and transmission LED
light up on the WMS Wall-mounted transmitter basic
(red and green).
The WMS Wall-mounted transmitter basic was added
to the network.

5
2018114_b•en•2019-10-01 We reserve the right to carry out improvements.
Step 2:
Copy a channel from a WMS Central transmitter to a
WMS Wall-mounted transmitter basic
 Select the "Allocate channel to another control panel"
menu item on your WMS Central transmitter under:
Main menu
 Products
 Product type
 Context menu
 Allocate
 Allocate channel to another channel
 Briefly press the learn button on the WMS Wall-
mounted transmitter basic.
The transmission LED on the WMS Wall-mounted
transmitter basic flashes green.
The channel was copied.
The exact description of these procedures can be found
in the instructions of the WMS Central transmitter (art. no.
890405).
Example 3:
An existing system with a WMS Wall-mounted
transmitter basic is expanded to include another
WMS Wall-mounted transmitter basic
Step 1:
Add the WMS Wall-mounted transmitter basic (2) to the
existing network with a WMS Wall-mounted transmitter
basic (1)
Button/
display Action/result
 Wake up the WMS Wall-mounted transmitter
basic (1) with the STOP button .
 Wake up the WMS Wall-mounted transmitter
basic (2) with the STOP button .
 Press the learn button on the WMS Wall-
mounted transmitter basic (1) for approx.
5 seconds.
+ lights up green; the transmission LED
flashes. For several seconds, the WMS
Wall-mounted transmitter basic (1) scans
the range for devices.
The WMS Wall-mounted transmitter basic (1)
does not find any device during scanning:
The transmission LED lights up.
ORANGE: No receiver found.
If the WMS Wall-mounted transmitter basic (1)
finds a receiver, transmitter or sensor that has
not yet been learned in, scanning is stopped.
It is indicated as follows:
The transmission LED lights up.
RED: New receiver
 When you press the control button ,
you can check WHICH target device was
just found.
The product then waves and the control
function LED flashes.
RED: The target device (transmitter
or sensor) can be added to the
network.
 Press the STOP button .
The found target device (transmitter or
sensor) is added to the network.
The target device waves in confirmation.
 Briefly press the learn button to leave
the learn mode.
Step 2:
Copy channel from one WMS Wall-mounted transmitter
basic (1) to another WMS Wall-mounted transmitter
basic (2)
Button/
display Action/result
 Briefly press the learn button on the WMS
Wall-mounted transmitter basic (1).
The L LED lights up green.
 Briefly press the learn button on the TARGET
TRANSMITTER (WMS Wall-mounted
transmitter basic 2).
The L LED lights up green.
The transmission LED on the WMS
Wall-mounted transmitter basic (1) flashes
GREEN During the transmission of data
from the WMS Wall-mounted
transmitter (1) to the WMS Wall-
mounted transmitter (2); this
ends with
GREEN Lights up continuously for
2 seconds,
transmission successful
RED Light up continuously for
2 seconds,
error during transmission
The L LED on the WMS Wall-mounted
transmitter basic (1) and (2) goes out.
Example 4:
The existing system with a WMS Wall-mounted
transmitter basic is expanded to include a WMS
Hand-held transmitter comfort
Step 1:
Add the WMS Hand-held transmitter comfort to the
existing network with a WMS Wall-mounted transmitter
basic
Button/
display Action/result
 Wake up the WMS Wall-mounted
transmitter basic with the STOP button .
 Wake up the WMS Hand-held transmitter
comfort with any product button.
 Press the learn button on the WMS Wall-
mounted transmitter basic for approx. 5
seconds.
+ lights up green; the transmission LED
flashes. For several seconds, the WMS
Wall-mounted transmitter basic scans the
range for devices.
The WMS Wall-mounted transmitter basic
does not find any device during scanning:
The transmission LED lights up.
ORANGE: No receiver found.
If the WMS Wall-mounted transmitter basic
finds a receiver, transmitter or sensor that has
not yet been learned in, scanning is stopped.
It is indicated as follows:
The transmission LED lights up.
RED: New device

2018114_b•en•2019-10-01We reserve the right to carry out improvements.
6
Button/
display Action/result
 When you press the control button ,
you can check WHICH target device was
just found.
The product then waves and the control
function LED flashes.
RED: The target device (transmitter
or sensor) can be added to the
network.
 Press the STOP button .
The found target device (transmitter or
sensor) is added to the network.
The target device waves in confirmation.
 Briefly press the learn button to leave
the learn mode.
You can now add additional scanned products in the
same manner.
 Briefly press the learn button to leave the
learn mode.
OTICEN If the large WMS Hand-held transmitter comfort
is still in its factory state (no products have
been learned in yet), the lights up in red after
the transmitter wakes up.
Step 2:
Copy channel from a WMS Wall-mounted transmitter
basic to a WMS Hand-held transmitter
Button/
display Action/result
 Press the learn button briefly.
The L LED lights up green.
 Wake up the large WMS Hand-held
transmitter comfort with any product
button.
 Select the desired channel on the target
transmitter by pressing and holding the
button of the desired product.
 Briefly press the learn button on the TARGET
TRANSMITTER.
The L LED lights up green.
The transmission LED on the WMS
Wall-mounted transmitter basic flashes.
GREEN During the transmission of data
from the WMS Wall-mounted
transmitter to the target
transmitter; this ends with
GREEN Lights up continuously for
2 seconds,
transmission successful
RED Light up continuously for
2 seconds,
error during transmission
The L LED on the WMS Wall-mounted
transmitter basic goes out.
Example 5:
Learn the WMS Wall-mounted transmitter basic
into a new receiver (plug receiver, actuator, etc.)
OTICEN The system can be comfortably commissioned
using our PC software WMS studio pro, a WMS
Central transmitter or the WMS Hand-held
transmitter comfort.
OTICEN Devices that do not belong to a network yet,
and are not intended to be learned in, must be
de-energised.
Button/
display Action/result
 Press the learn button on the WMS Wall-
mounted transmitter basic for approx. 5
seconds.
+ The L LED lights up green; the
transmission LED flashes. For
several seconds, the WMS Wall-mounted
transmitter basic scans the range for
receivers.
 By pressing the learn button again, the
process can be aborted.
The L LED goes out.
If, while scanning, the WMS Wall-mounted
transmitter basic finds a target device
(receiver, transmitter, sensor) that has already
been learned in:
The transmission LED lights up.
GREEN: Lights up continuously for 2
seconds
Then scanning continues.
The WMS Wall-mounted transmitter basic
does not find any device during scanning:
The transmission LED lights up.
ORANGE: No receiver found.
If the WMS Wall-mounted transmitter basic
finds a receiver, transmitter or sensor that has
not yet been learned in, scanning is stopped.
It is indicated as follows:
The transmission LED lights up.
RED: New receiver
 When you press the control button ,
you can check WHICH target device was
just found.
The product then waves and the control
function LED flashes.
GREEN: The target device is a receiver
for which the product type can
be adjusted.
By pressing the UP and DOWN arrow buttons,
you can select the desired receiver/product
type:
 Press UP
Flashing increases by one
 Press DOWN
Flashing decreases by one

7
2018114_b•en•2019-10-01 We reserve the right to carry out improvements.
Button/
display Action/result
Depending on the frequency with which
the control function LED flashes, the
corresponding product type is displayed:
1 x GREEN: Awning
2 x GREEN: Roller shutter
3 x GREEN: External venetian blind
4 x GREEN: Light
5 x GREEN: Window
 To check which product type was set,
press the control button .
The flashing of the control function LED
indicates which product type was
selected.
OTICEN If the desired receiver is not
waving after the button has
been pressed, a brief press of
the button switches to the next
receiver found during the scan.
 Press the STOP button .
The appropriate product type is now
assigned to the receiver.
The transmission LED lights up for 2
seconds.
GREEN This confirms the assignment.
OTICEN The first receiver that is learned into the WMS
Wall-mounted transmitter basic defines the
channel type. If an external venetian blind is
learned in as the receiver first, the channel
type is defined as an external venetian blind
channel and only external venetian blinds can
be learned in.
The transmission LED flashes
GREEN: The scan process is now
repeated automatically until
no more new devices are
found.
The transmission LED lights up.
ORANGE: The scan is ended.
 Briefly press the learn button to leave the
learn mode.
Example 6:
Delete learned-in products from the WMS Wall-
mounted transmitter basic and the network
You can remove the learned-in products completely from
the WMS Wall-mounted transmitter basic and the network.
First, scanning is repeated (see example 5 on page 6)
to identify the learned-in devices.
OTICEN Devices that do not need to be deleted must be
de-energised.
As soon as the transmission LED lights up orange, you
can start the deletion process.
Button/
display Action/result
 Press the learn button on the WMS Wall-
mounted transmitter basic for approx.
5 seconds.
+
The L LED lights up green; the
transmission LED flashes. For several
seconds, the WMS Wall-mounted transmitter
basic scans the range for receivers.
Button/
display Action/result
 By pressing the learn button again, the
process can be aborted.
The L LED goes out.
If, while scanning, the WMS Wall-mounted
transmitter basic finds a target device
(receiver, transmitter, sensor) that has already
been learned in:
The transmission LED lights up.
GREEN: Lights up continuously for
2 seconds
Then scanning continues.
The transmission LED lights up for
2 seconds.
ORANGE Scanning stops.
+  Press the STOP button and
simultaneously.
The delete command is sent to all learned-
in receivers.
Those receivers that are still learned-in wave
when they are deleted from the WMS Wall-
mounted transmitter basic and the network.
The transmission LED indicates the result
of the deletion process:
The transmission LED flashes
GREEN: The devices are deleted.
The transmission LED flashes
RED: Not all target devices have
been deleted.
 Press the STOP button .
The deletion command is sent repeatedly
to find receivers that were not within
the radio range during the first deletion
command and to delete them as well.
 Briefly press the learn button to leave the
learn mode.
OTICEN When you delete a receiver from the network,
it can no longer be operated via other
transmitters. It must be relearned into a
network.
OTICEN It only makes sense to delete products via
the WMS Wall-mounted transmitter basic in
smaller networks (two to three awnings or roller
shutters). In more complex networks and when
routing tables are used, a WMS hand-held
transmitter comfort or a central control unit
should be used for deletion.

2018114_b•en•2019-10-01We reserve the right to carry out improvements.
8
Maintenance
Dismantling
 To remove the wall-mounted transmitter (for example
to change the battery), carefully pull the clipped wall-
mounted transmitter off of the frame.
 Hold onto the central frame/plate as it comes loose
automatically when the wall-mounted transmitter is
removed.
Replacing the batteries
Replace the battery if the transmission LED lights up
orange after the WMS Wall-mounted transmitter basic is
activated. If the battery is fully depleted, the WMS Wall-
mounted transmitter basic can no longer be activated.
 When inserting the new battery (coin cell CR2032),
watch for the correct polarity: The positive terminal (+)
of the battery faces up (visible), the minus terminal (-)
of the battery faces down (see Fig. 4).
 Only touch the battery on its edge.
 When inserting the battery, make sure that it is pushed
to one side under the contacts.
 Use a high-quality battery – inexpensive batteries may
leak and damage the device. If the device will not
be used for an extended period, please remove the
battery.
Liability
Failure to comply with the product information in
these instructions and use of the unit in a manner that
contravenes its intended use and purpose may result in
the manufacturer refusing to honour warranty claims for
product damage. In this case, liability for secondary harm
to persons or damage to property will also be excluded.
Follow the instructions in the operating instructions of your
sun shading system. Liability is also excluded for damage
to the sun shading system resulting from operation under
icy conditions.
Disposal
After use, the device and the battery must be disposed
of according to legal regulations or brought to your local
recycling centre.
Technical data
WMS Wall-mounted
transmitter basic Min. Typ. Max. Unit
Supply
Battery type 1 x coin cell CR 2032
Operating voltage 1.8 3.0 3.2 V DC
RF transceiver
Transmission frequency 2.40 2.48 GHz
Transmission power 0 dBm
Reception sensitivity -101 dBm
Range
(environment without
interference)
30 m
Housing
WMS Wall-mounted transmitter
basic (L×W×H in mm)
50 × 50 × 10.5
Mounting frame (L×W×H in mm) 70 × 70 × 5
Degree of protection IP30
Safety class III
Miscellaneous
Conformity
Available at www.warema.de/ce
This device meets the EMC directives for use in
residential and commercial areas.
WAREMA Renkhoff SE declares herewith that this
radio system type [WMS Wall-mounted transmitter basic] is in
compliance with the current guidelines.
Ambient conditions
Operating temperature 0 50 °C
Storage temperature 0 70 °C
Rel. humidity
(non-condensing)
10 40 85 %RH
Degree of soiling 2
Article numbers
Scope of delivery
WMS Wall-mounted transmitter
basic anthracite
1002 964
WMS Wall-mounted transmitter
basic white
1002 881
WMS Wall-mounted transmitter
basic silver
2003 494
Optional accessories
WMS Wall-mounted transmitter
frame, anthracite
(consisting of a central frame/
plate and switch program
frame)
2004 343
WMS Wall-mounted transmitter
frame, white
(consisting of a central frame/
plate and switch program
frame)
2004 341
WMS Wall-mounted transmitter
frame, silver
(consisting of a central frame/
plate and switch program
frame)
2004 342
WAREMA Renkhoff SE
Hans-Wilhelm-Renkhoff Strasse 2
97828 Marktheidenfeld
Germany