Warmset WHT 1000 User manual

Page1
Advanced settings
To enter the advanced settings, you need to press button to turn o the thermostat. Then press and hold for about 5 seconds until menu 01
is shown on screen. Press to select menu number, and press or to adjust the settings for each menu. Below are examples and menu list.
Auto / Manual mode
Press to select between Auto and Manual mode. In manual mode, the thermostat maintains a constant set temperature manually set by the user. In Auto
mode, the thermostat follows the programmed schedule.
Installation Manual
Sensor Selection
A = Air sensing using built in sensor
F = Floor sensing using remote oor temperature
AF = Air sensing for setpoint, oor sensing for safety cut o
Menu #
Menu 01
01
Programming Option - 2 options for time/temperature settings
5_2 = 5 days (Mon - Fri) with same time/temperature settings and 2 days (Sat - Sun) with
same time/temperature settings
7_0 = 7 days allow for individual day settings or whole week settings
Floor Temperature Limit - Provides oor temperature protection when using AF function
12/24 Hour clock
Select backlight function
Thermostat Calibration (FLOOR) - By adjusting this gure any discrepancy between
displayed oor temperature and measured oor temperature can be compensated for
Switching dierential - The number of degrees dierence between switching o at the
set temperature and on again to reach the set temperature i.e. A 1°C setting will switch
the thermostat on 0.5 °C below the setpoint and switch it o 0.5 °C above the setpoint
30 seconds 10,20,30......60 ,ON
12 / 24
Thermostat Calibration (AIR) - By adjusting this gure any discrepancy between
displayed air temperature and measured air room temperature can be compensated for
02
03
04
05
06
07
08
09
10
11
Feature Description Factory Default
Options
0 °C
5_2 5_2 / 7_0
40 °C
20°C ~ 90 °C
24
OFF OFF / ON
A / F / AF
A / F / AF
A
A
Press or to select
Frost protection - Set to ON to maintain a room temperature above 5°C in the event of
severe low temperatures
1°C 1°C ~ 5°C
-5°C ~ +5°C
0°C -5°C ~ +5°C
Power Up/Down
Day of the week
Periods
key lock
AUTO
Anti-frozen
FLOOR
Clock setting
WHT 1000 Thermostat
Explanation of Symbols
Manual Mode
Auto Mode Heating On
Room Temperature
Floor Temperature
Time
Menu
WiFi symbol
If menu 01 is set to AF. Use menu 05 to choose to show air temperature, oor temperature
This allows users to select between °C or °F. °C °C / °F
or to show both oor & air in interval.
option
thermostat is
turned off
Menu 02
option

Page2
WHT 1000 Thermostat
Setting the Programme Schedules
Installation Manual
Period
1
2
4
Period Icon Default Start Time Default Set Temp
7:00
P1
P2
P3
P4
8:30
16:30
22:30
22℃
16℃
22℃
16℃ 3
Press for about 5 seconds , the day display will ash. (if your thermostat is in 5+2 day programmable mode, the programming will skip to step 3).
Press , the LCD will show period 1( P1 ) with the time ashing.
Press or to adjust the time you wish period 1 to start for the selected day(s);
Press , the temperature will start ashing
Press or to adjust the temperature for period 1( P1 );
Finally , press to conrm and exit.
Finally , press to conrm and exit.
Press ,the LCD will show period 2 ( P2 ) with the time ashing.
Repeat Steps 4-7 until all 4 periods are set.
1.
2.
3.
4.
5.
6.
7.
Press or to select the day you want to program. Press and hold or to select whole week and to cancel, repeat the press and hold.
Setting the clock and day of the week
Lock the keypad
Temporary Temperature Override
Press to select hour, minute and day of the week. Press or to adjust.
To lock the keypad, press and hold for about 3 seconds, you will see the lock symbol , to unlock repeat the steps above.
To temporary override the current temperature in Auto mode, simply press or to adjust the set point, press to confirm the change.
O/RIDE will appear above the temperature display. The override setpoint will remain until the next scheduled period. To cancel override, simply press .
Installation and Wiring
Wiring Diagram Error Message
Carefully separate the front half of the thermostat fromthe back plate by placing a
small at head terminal driver into the slots on the bottom face of the thermostat.
Carefully unplug the the front half of the thermostat.
Place the thermostat front half somewhere safe. Terminate the thermostat as shown
in the diagrams below.
Screw the thermostat back plate on to the ush box. Plug the front half of the
thermostat into the back plate and clip the two halves together.
E0 = The internal sensor has developed a fault. You should
contact your thermostat retailer for assistance.
E1 = The remote floor sensor has not been connected, has
been wired incorrectly or the probe is faulty.
LO = The room or floor temperature is below 0
°C
HI = The room or floor temperature is above 50
°C
123456
AC230V
L
~
N
~
MAX LOAD：16A
50/60Hz
IP 21
L1 N1
FLOOR SENEOR
POWER