Warmset WTR8200 User manual

WTR8200 Thermostat User Manual
LCD Symbols
Configuration Menu
Setting the clock and day of the week
Select the required operating mode
This thermostat is fitted with a real time clock. It is essential that the clock time and day are set accurately if you require your programmed events to start on time. Follow below steps,
1) Touch time display .
Auto - Automatic mode, the thermostat executes the preprogrammed schedules. To adjust these schedules, see page 2 the program section.
In addition to Automatic mode, this thermostat has 3 extra manual modes, i.e , each of these manual modes maintains a constant set temperature set by the user.
- Comfort temperature mode, the highest temperature you want to achieve, this is the temperature that will be required when the room is in use. Default is 22 °C.
- Economy temperature mode, the lowest temperature, the temperature you want to go no lower than when the room is not in use. Default is 16 °C.
-Vacation temperature mode, this is set to stop your floor from going below the set temperature. Default is 10 °C.
To change the set temperatures, touch temperature display. Use or to adjust to the required temperature. Touch to store and exit.
See overleaf for further setting up information
2) Touch day display .
Use or to change the time. Press and hold
Use or to change the day. Touch to store and exit.
or to change the time faster. Touch to store and exit.
The buttons are locked
Turning on/off the thermostat
Heating is turned on
Automatic mode, executes the programmed schedules
The sensor is not being read by the thermostat
Err
Temporary temperature override
Frost protection activated
Room temperature
RT
AUTO
Floor temperature
FT
O / RIDE
Symbols
The program number
Day of the week. Day 1= Monday, Day 2= Tuesday... etc.
Reminding the user to connect the floor sensor (AF and F model only)
Touch to view floor temperature for 5 seconds (AF model only)
Touch to switch among Auto
Touch to start programming of your thermostat
Comfort temperature mode
Economy temperature mode
Day
Program 1,2,3,4
Vacation temperature mode
Symbols Description
Description
This thermostat is a combination model allowing you to choose among 3 models.
A model: air only , with built in sensor
AF model: air & floor, with both built in and remote sensor
F model: floor only , with remote sensor
Menu #
01 Model selection
Switching differential02
Features description Features Explanation
A, AF, F
Touch or to adjust
Backlight turning-on time06 10, 20,30,40,50,60 seconds. 30 seconds by default
To set the backlight turning-on time when the screen is pressed.
Temperature format07 C / FThis allows users to select between °C or °F.
Clock format 24H / 12H 24 hour clock by default08 12 Hour or 24 Hour clock format selection
03 0 °C by default, -5°C ~ +5°CCalibrate the room temperature
To compensate for any difference between the displayed room temperature and a thermometer
04 0 °C by default, -5°C ~ +5°C To compensate for any difference between the displayed floor temperature and a thermometer Calibrate the floor temperature
ON = sound audible; OFF = sound off11 Key click sound Choose whether or not a key click sound is audible when you press the LCD screen
ON = activated; OFF = deactivated09 Frost protection This is to avoid room temperature goes below 5°C
For review only12 Software version This is to view the current software version
Set
Schedule
Heating
Mode
Done
Done
Done
Then you will see menu 01. Touch or to select the menu number. Use or adjust the settings. Touch to accept and store.
Previous Done
Next
The numbers of degree difference before switching. The default is 1°C which means
the thermostat will switch the heating on 0.5°C below the set temperature and will
turn it off 0.5°C above the set temperature.With a 2°C differential, the heating will
switch on 1°C below the set temperature and switch off 1°C above the set temperature.
1 °C, 2 °C, ...10°C, 1 °C by default
Maximum floor temperature05 40 °C by default, setting range 20°C ~ 40°CThis is to protect the floor surface by limit the floor temp. ( AF model only)
10 5+2 /7 Day program mode This allows you to program either 5 days at once, then the 2 days of the weekend 5 2 = 5+2 day programmable
separately, or a full 7 days at the same time or 7 days separately 7 = 7 day programmable (by default)
touch to turn thermostat off, and now touch
Set Menu
To enter into menu settings,

Save money by setting program schedules
This thermostat can be individual 7-day programmable. For each day of the week you are able to have 4 timed set temperature schedules.
Above are default program schedules, to make changes, follow easy steps as below.
Set to the time you would like to wake to and the temperature you want during the morning, until you left for the day.
Set to the time you leave home and the temperature you wish your home to maintain while you are away at work perhaps.
Set to the time you return home at end of the day and the temperature you want during evening until bed time.
Set to the time you sleep and the temperature you want overnight(usually a comfortable and energy saving temperature).
07:001
2
3
4
22 °C
16:30 22 °C
09:30 16 °C
22:30 16 °C
WAKE
Program Start Time Setpoint Explanation
LEAVE
RETURN
SLEEP
This product should be
installedby a qualified
Carefully separate the front half of the thermostat
from the back plate by placing a small flat head
terminal driver into the slots on the bottom face of
the thermostat
1
Carefully unplug the ribbon connector
which is plugged in to the front half of
the thermostat
2
Place the thermostat front half somewhere
safe. Terminate the thermostat as shown
in the diagrams below
3
Screw the thermostat back
plate on to the back box
4
Re-connect the thermostat ribbon cable
and clip the two halves together
5
Installation and Wiring
Press , you will see day display flashing.
Use or adjust the day to the day you wish to start programming
Press , the LCD will show program 1 with the time display flashing.
Use or adjust the time you wish the program 1 event to commence
Press , the LCD will show a temperature value flashing.
Use or set the desired heating temperature to be maintained for
Press , now the LCD will show program 2 with the time display
Repeat step 4,5,6 to set remaining programs. Press to store and exit.
Note: During setting programs, press (if visible) will clear a program entry
1.
2.
3.
4.
5.
5.
6.
6.
7.
8.
WTR8200 Thermostat User Manual
(Press to select all days of the week, to cancel selecting all days of
DONE
DONE
All Days
All Days
Set
Schedule
Temporary Temperature Override
Touch the temperature display, and it will start to flash. Use
or
to adjust. Press to accept, and you will see “O/RIDE” on LCD. Thermostat will maintain the
new set temperature until the next programmed event(comfort level). To cancel the override setting, press
Lock the Keypad
To lock the keypad, press and hold the bottom left corner of display for 5 seconds, you will see a lock symbol .
Reset to Factory Settings
With thermostat turned off, press and hold the up left corner of display for 5 seconds until you can see RESET on LCD.
To unlock, repeat the steps above.
DONE
Run
Schedule
Next
Next
Next
Next
Next
Next
Delete
until the beginning of the next program.
Note: It is faster to program the same schedule for the entire week and then to
adjust the exceptional days.
Set time and temperature for the next time period(Leave). Repeat steps 2 and 3
for each time period of the weekday.
In 7 day program mode In 5+2 day program mode
flashing, signifying the second daily event is now being programmed.
the program 1 event.
for the currently selected day or days.
the week, press again.)
or to the day you wish to edit an existin
g event or program.
Press , you will see the time flashing.
Press to move to the weekend(sat-sun) time periods settings.
Use or to set your weekday Wake time(Mon-Fri), then press
1.
2.
3.
4.
Use or to set the temperature for this time period, then press
Set
Schedule
Press to save and exit.
Day 1 - 5, refers to the weekday( Monday to Friday)
Day 6 - 7, refers to the weekend( Saturday and Sunday)
and thermostat will maintain the temperature setpoint of the last executed program
electrician.