WARRIOR Soccer Table User manual

Updated: 3/6/2014 WWW.WARRIORTABLESOCCER.COM
SOCCER TABLE
Assembly Instructions

www.warriorcustomgolf.com 2 | P a g e
Table of Contents
Parts Identifier .......................................... 1
Hardware Identifier…………………………. 2
Table Assembly Instructions ..................... 3
Table Assembly Pictures ………..….…….. 4
Installation of Light Brackets………...…… 5
Light Bracket Installation Pictures..……… 6

www.warriorcustomgolf.com 3 | P a g e
Parts Identifier
Box A
A1. Side panels (2)
A2. Assembled rods with bearings (8), Rod guards (8)
A3. Light post (2), Bolts (4), Washers (8), Plastic plug (4)
Note: This light post works best with Utilitech 48-in Fluorescent Shop Light. Item #: 420866
Model #: MXL-102
Box B
B1. Leg panels (2)
B2. Goal boxes (2)
B3. Top Cap (2)
Box C
C1. Table top (1)
C2. Leg levelers (4)
C3. Ball Catch (1)
C4. Score beads (2)
C5. Corner insert (4)
C6. Ball Return Hose (2)
C7. Bolts & washers (all nuts pre-installed in cabinet)
C8. Allen wrench with Phillips head.

www.warriorcustomgolf.com 4 | P a g e
Hardware Identifier
Description Qty Purpose
H1. 5/16” x 1 ¾” 12 (8) Step 2 side panels, (4) Step 7 corner blocks
H2. 5/16” x 1 3/8” 6 Step 7 Playfield/Table Top
H3. 1/4" x 1 ½” 2 Step 5 Ball Catch
H4. 1/4" x 1 ¾” 4 Step 9 Top Plate
H5. 3/16” x 1 ½” 4 Step 10 Score Beads
H6. 1/4" x 1 ¼” 4 Step 3 Goal Boxes
H7. 1/4" x 1 ¾” 4 Page 5 Installation of Light Brackets

www.warriorcustomgolf.com 5 | P a g e
Table Assembly Instructions
Note: No additional tools required for assembly, all nuts are pre-installed in the table. It is recommended to get
all bolts “Started” only. Once all bolts have been started check alignment of “top plates”, “leg panels” & “side
panels” before tightening bolts completely.
1. Install leg levelers (4) onto leg post by twisting in clockwise direction then stand
both legs in upright position.
2. Position both side panels (2) on each side of the leg panels (make sure the
predrilled holes are on the top side), using (8) 5/16” x 1 ½” bolts attach side
panels to leg panels. (Heads Up-you may find some or all of these bolts 1 ¾” in length
from factory. OK to use.)
3. Attach goal boxes (2), using (4) 1/4” x 1 1/2” bolts and washers.
4. Insert metal plate into precut slots in goal box.
5. Attach ball catch (1) using (2) 1/4” x 1 ½” bolts with washers.
6. Install ball return runners (2)
a. First hold the end of the “ball return runner” in one hand and with your other hand
press down firmly on the top edge with your index finger to create a “V” on the top
edge of the hose (see runner installation pics r1 & r2, page 6)
b. With the goal box mounted, insert hose into the hole at the base of the goal box
until bottom edge of hose touches the mdf just inside the hole (this puts the hose
flush with the inside of the hole at the base of the goal box. (see runner installation
pics r3, page 6)
c. Using your index finger, reach inside the hose and press up firmly removing the
“V” making the hose round again. This hose will stay in place and the ball will
drain perfectly to the “ball catch” every time. (see runner installation pics r4, page
6)
d. Use this method to inserting hose into the “ball catch” as well.
7. Place table top onto cabinet and secure using (6) 5/16” x 1 3/4” bolts with
washers.
8. Attach corners blocks (4) to side of table using (4) 5/16” x 1 1/4” bolts with
washers.
9. Attach top plate (2) using (4) 1/4” x 1 3/4” bolts.
10. Attach score beads (2) on to top plate using (4) #10 x 1 1/2” bolts.
11. Place rods onto table top starting on any side.
Note: In the event the bearings are super tight or won’t easily go in it may be necessary to
prepare the hole with some emery cloth or a 1/2 round file to smooth out the inside diameter of
the hole and knock the burr off.
a. –1 man rods with 10“rod guard
b. –2 man rod with 15“rod guard

www.warriorcustomgolf.com 6 | P a g e
c. –3 man rod (opponent) with 10“rod guard
d. –5 man rod with 5“rod guard
e. –5 man rod (opponent) with 5“rod guard
f. –3 man rod with 10“rod guard
g. –2 man rod (opponent) with 15“rod guard
h. –1 man rod (opponent) with 10“rod guard
Put a couple drops of silicone on the rods and you’re ready to go!
Installation of Ball Return Hose
R1 –create “V” on return hose edge
R2 –“V” in return hose edge
R3 - insert return hose into base of goal box
R4 –remove “V”

www.warriorcustomgolf.com 7 | P a g e
Assembly Pictures
1. Leg Levelers
2. Leg Panels w/ 1 Side Panel
3. Goal Box
4. Metal Plate
5. Ball Catch
6. Table Top

www.warriorcustomgolf.com 8 | P a g e
Installation of Light Brackets and Fixture
Note: Instructions below are detailed for use with our recommended light fixture, with any other
fixture instructions may not be exact but will probably be similar. If you decide against installing
light bracket at this time, use the (4) black caps found in the hardware kit to cover the holes.
1. Attach Light Brackets (2) using (4) 1/4” X 1 3/4” bolts and washers to the base of
either end of the table where you will find 2 holes (one above the other) with t-
nuts installed.
2. Loosen screws a & b (photo L2) enough to insert light bracket (see photo L2)

www.warriorcustomgolf.com 9 | P a g e
Light Bracket Installation Pictures
L1
Utilitech 48-in Fluorescent Shop Light. Item #:
420866 Model #: MXL-102 $14.98
Lowe’s Hardware
L2
L3
T-nuts in place to accept 1/4 x 1-3/4” bolts for
securing light brackets
L4
Screw A
Screw B

www.warriorcustomgolf.com 10 | P a g e
Notes: