WARRIOR W0700R User manual

INSTRUCTION MANUAL
Heavy-DutyCabinet Table Saw
30" Rip Capacity Model 50" Rip Capacity Model

Contents
1. Machine Description .................................................................................................................2
1.1 Technical Parameters.............................................................................................................2
1.2 Feature Identification .............................................................................................................. 3
1.3 Intended Use ...........................................................................................................................3
2. Safety Regulations ....................................................................................................................4
2.1. General Safety Instructions...................................................................................................4
2.2. Table Saw Safety Instructions ..............................................................................................4
2.3. Residual Risks........................................................................................................................5
2.4. Safety Eequipment.................................................................................................................5
3. Installation of the Machine.......................................................................................................6
3.1 Transportation of Machines....................................................................................................6
3.2 Unpacking................................................................................................................................6
3.3 Contents...................................................................................................................................7
3.4 Installation............................................................................................................................... 9
4. Adjustment............................................................................................................................... 15
4.1 Adjusting the Rip Fence .......................................................................................................15
4.2 Aligning the Table T-slot Parallel with the Blade................................................................15
4.3 Adjusting the 45°and 90°Positive Stops .............................................................................15
4.4 Aligning Riving Knife with the Blade....................................................................................16
4.5 Calibrating the Saw Blade Angle DRO ......................................................................... 16
5. Operations................................................................................................................................ 17
5.1 Electrical Operation...............................................................................................................17
5.2 Blade Elevation and Tilting Adjustment ..............................................................................17
6. Maintenance..................................................................................................................................17
7. Trouble Shooting.........................................................................................................................18
8. Exploded View and Parts List....................................................................................................19

2
1. Machine Description
1.1 Technical Parameters

3
1.2 Feature Identification
50" Model Refer to Fig. 1.
Fig. 1
1 Left Extension Wing
2 Blade Guard
3 Main Table
4 Right Extension Wing
5 Fence Assembly
6 Extension Table
7 Rail Assembly
8 Support Leg
9 Motor Cover
10 Cabinet
11 Blade Elevation Hand Wheel
1.3 Intended Use
This table saw and the workpiece guide equipment
supplied with it are intended to be used exclusively
for the following purposes:
●Laminated and unlaminated board materials (e.g.
chipboard, coreboard, MDF board, ...)
●Solid wood
●Gypsum plasterboard, Cardboard, Veneer with a
suitable clamping device
●Dimensionally stable plastics (thermoset plastics,
thermoplastics).
Tools:
●The chosen saw blade must be suitable both for the
specific work cycle and for the specific material.
●Only circular blades which are solid chrome
vanadium (CV) or tungsten carbide tipped (TCT) and
have a diameter of 305mm (12”), arbor size of
15.875 mm (5/8”) or 30mm, as well as a maximum
mounting width of 20.3 mm are allowed for the main
saw.
Site of installation / use:
●The machine is not suitable for use outdoors, or in
rooms that are subject to moisture or the risk of
explosions.
12 Blade Tilt Hand Wheel
13 Miter Gauge
14 Fence Arm Rest
15 OverArmDustCollection(system)
16 Magnitic Starter
17 Service Door
NOTE:
Fig.1 is only for illustration, and the actual
object shall prevail.
●The intended use of the machine involves
connection to a suitably dimensioned dust extraction
system .
●Intended use also involves compliance with our
specified operating, maintenance and repair
conditions and the safety information contained in
the operating instructions.
●The table saw may only be used, set up and
maintained by persons who are familiar with the
machine and aware of the dangers.
●The pertinent accident prevention regulations as
well as any other generally recognized technical
safety and industrial health rules must be observed.
●Repair work must be carried out by our own
customer service or by an authorized repair center.
Only original spare parts are allowed to be used on
this machine. We will assume no warranty for any
damage that is caused by using non-original spare
parts.

4
2. Safety Regulations
2.1 General Safety Instructions
1. KNOW YOUR MACHINE.
Read and understand the owner’s manual and
labels affixed to the machine. Learn its application
and limitations as well as its specific potential
hazards;
2. GROUND THE MACHINE.
In the event of an electrical short, grounding
reduces the risk of electrical short;
3. KEEP THE BLADE GUARDS IN PLACE.
Keep in good working order, properly adjusted and
aligned;
4. REMOVE THE ADJUSTING TOOLS
Form a habit of checking that the key and adjusting
wrenches are removed from the machine before
turning it on;
5. KEEP THE WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
Make sure the floor is clean and not slippery due to
wax and sawdust build-up;
6. AVOID A DANGEROUS ENVIRONMENT.
Don’t use machines in damp or wet locations or
expose them to rain. Keep the work area well lit
and provide adequate surrounding work space;
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from
work area;
8. MAKE WORKSHOP CHILD-PROOF.
With padlocks, master switches or by removing
starter keys;
9. USE THE PROPER SPEED.
A machine will do a better and safer job when
operated at the proper speed;
10. USE THE RIGHT MACHINE.
Don’t force the machine or the attachment to do a
job for which it was not designed;
11. WEAR THE PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or
jewelry (rings, watch) because they could get
caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the
elbows;
12. MAINTAIN PROPER FOOTING.
Keep proper footing and balance at all time. Do
not over-reach to perform an operation;
13. MAINTAIN THE MACHINE WITH CARE.
Keep tools sharp and clean for the best and safest
performance;
14. DISCONNECT MACHINES.
Before servicing, when changing accessories or
attachments;
15. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the “OFF” position
before plugging in;
16. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories.
Follow the instructions that accompany the
accessories. The use of improper accessories may
cause hazards;
17. NEVER STAND ON THE MACHINE.
Serious injury could occur if the machine tips over.
Do not store materials such that it is necessary to
stand on the machine to reach them;
18. CHECK FOR DAMAGED PARTS.
Before further use of the machine, a guard or other
parts that are damaged should be carefully
checked to ensure that they will operate properly
and perform their intended function. Check for
alignment of moving parts, breakage of parts,
mounting, and any other conditions that may affect
its operation. A guard or other parts that are
damaged should be properly repaired or replaced;
19. NEVER LEAVE THE MACHINE RUNNING
UNATTENDED.
Turn the power to "off". Do not walk away from the
machine until it comes to a complete stop;
20. ADEQUATE LIGHT
Ensure that adequate general or localized lighting
is provided in work area;
2.2 Table Saw Safety Instructions
1. ALWAYS USE A GUARD.
Always use a guard, splitter on all “thru-sawing”
operations. Thru-sawing operations are those
when the blade cuts completely through the work
piece as in ripping or crosscutting;
2. ALWAYS HOLD THE WORK.
Always hold the work firmly against the miter
gauge or fence;
3. ALWAYS USE A PUSHSTICK OR PUSH
BLOCKS.
Push blocks or push sticks shall be used when
cutting small workpieces and in circumstances
where it is necessary to push the workpiece
against the fence;
4. NEVER PERFORM UNSAFE OPERATIONS.
Never perform any operations “free-hand” which
means using your hands to support or guide the
work piece. Always use either the fence or the
miter gauge to position and guide the work piece;

5
5. STAND TO THE SIDE WHEN FEEDING
MATERIAL.
Never stand or have any part of your body in line
with the path of the saw blade;
6. USE CAUTION WHEN REACHING FOR
OBJECTS.
Never reach behind or over the cutting tool with
either hand for any reason;
7. SAFE CROSSCUTTING OPERATIONS.
Move the rip fence out of the way when
crosscutting;
8. ENSURE CORRECT FEEDING OF MATERIAL.
Feed the work into the blade against the direction
of rotation;
9. CORRECT USAGE WITH THE FENCE.
Never use the fence as a cut-off gauge when you
are cross-cutting;
10. ALWAYS TURN THE POWER TO THE "OFF"
POSITION.
When attempting to free a stalled saw blade,
always turn the saw to the "off" position;
11. PROVIDE ADEQUATE SUPPORT.
To the rear and sides of the table saw for wide or
long work pieces;
12. AVOID KICKBACKS.
Avoid kickbacks (work thrown back towards you)
by keeping the blade sharp, by keeping the rip
fence parallel to the saw blade, by keeping the
splitter and guard in place and operating, by not
releasing work before it is pushed all the way past
the saw blade, and by not ripping work that is
twisted or warped or does not have a straight edge
to guide along the fence;
13. AVOID AWKWARD OPERATIONS.
Avoid awkward operations and hand positions
where a sudden slip could cause your hand to
move into the spinning blade;
14. CORRECT SAW BLADE USAGE.
No saw blade shall be used where the maximum
marked speed is lower than the maximum
rotational speed of the saw spindle;
15. CHIP AND DUST.
The machine shall be connected to an external
chip and dust extraction system;
The dust extraction equipment is to be switched on
before commencing machining;
16. CHECK
Periodically check stop time of blade to make sure
the completed stop time of the saw blade is less
than 10 seconds.
2.3 Residual Risks
1. Take precautions to reduce the hazard of
inhalation of harmful dust (e.g. wearing a dust
mask);
2. Wear ear protection to prevent hearing loss;
3. Always wear safety glasses. Also, use a face
or dusk mask if the cutting operation is dusty;
4. Protect against the hazard of being cut when
handling saw blades in the machine or while
performing maintenance on the machine;
5. Do NOT try to remove chips while the saw is
running or the saw blade is moving;
6. Do NOT use the machine unless all of the
guards and other safety devices necessary for
the particular operation are in good working
order and in place.
2.4 Safety Equipment
When cutting narrow workpieces, a Push Block
must be used. Push the work piece against the
fence if necessary. A push block can be easily
made by the operator as shown in Fig. 2.
If the workpieces is less then 4-3/4” (120 mm), you
must use the push stick, as shown in Fig.3, to
prevent your hands from getting too close to the
saw blade.
Fig. 2
Fig. 3

6
3. Installation of the Machine
3.1 Transportation of Machines
5.1.1 Transportation and store
This machine has been well packaged and rust
preventive measures have been taken at the
factory. Care should still be taken to insure that no
damage comes from rough handling while moving.
Ambient temperatures of -10 to 130 ℉ (-25 to
55 ℃) can be endured by this machine.
Be careful not to expose this machine to rain or
other severe weather.
While transporting or handling the machine, be
careful and let the activity be done by qualified
personnel especially trained for this kind of
activity!
While the machine is being loaded or unloaded,
make sure all persons are out of the way so
that no person is crushed by the machine.
Select the proper transportation device
according to the weight of the machine. Make
sure the lifting capacity of the transportation
device is sufficient for the weight of the
machine.
3.1.2 Transportation before unpacking
This machine is packed in a robust cardboard box.
Fig. 4 shows the device which can be used to
transport the packed crate.
Fig. 4
3.2 Unpacking
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover that the machine is damaged, please
immediately call Customer Service for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
Note: If you can't find an item on this list, check
the mounting location on the machine or
examine the packaging materials carefully.
Occasionally we pre-install certain components
for shipping purposes, or in other packing.

7
J I
N
M1 KM2
O1
O2
3.3 Contents
Main machine box contents:
(Fig. 5-1 ----Fig. 5-5)
A. Main table saw unit ................................1
B. Motor cover.............................................1
C. Left extension wing ................................1
D. Right extension wing .............................1
E. Extension table.......................................1
(for 50" Rip Capacity model only)
F. Support legs… ........................................ 2
H1. Inner dust port.....................................1
H2. Outer dust port....................................1
J1. Wrench open-ends 8-10 mm................ 1
J2. Wrench open-end 13-16 mm...............1
J3. Arbor wrench..........................................1
K. Push stick................................................1
L. Hex wrench set (four pieces) ............. 1
M1. Dado table insert ....................................1
M2. Zero Clearance insert............................1
N. Handwheel handle .................................2
O1. Blade guard assembly ...........................1
O2. Riving knife.......................................... 1
P. Fence holder........................................ 1
R. Miter gauge ............................................1
Fig. 5-2
Fig. 5-3
Fig. 5-4
Fig. 5-1
Fig. 5-5

8
Fence box contents: (Fig. 5-6)
A. Fence body ...............................................1
B. Fence ..........................................1
Fig. 5-6
Rail box contents: (Fig. 5-7)
A. Rear rail.....................................................1
B. Front rail....................................................1
C. Front rail rectangular tube......................1
D. Front rail tape scale ................................1
Note ：
The assembly contains the corresponding
hardware which is not shown in the figure, and
can be checked with the exploded view.
Fig. 5-7
Note ：
There are two types of the guide rails, please
have a check according to the name plate of the
machine:
1. 30 guide rail is for SWDS-2305-30-F.
2. 52”guide rail is for SWDS-2305-50-F.
Over arm box contents: (Fig. 5-8)
A. Over arm ...................................................1
B. Flexible hose (length 0.6 m) ...................1
C. Flexible hose(length 1 m)........................1
D. Bracket ......................................................2
Note ：
The assembly contains the corresponding
hardware which is not shown in the figure, and
can be checked with the exploded view.
Fig. 5-8

9
3.4 Installation
Before beginning assembly, take note of the
following precautions and suggestions:
FLOOR: This tool distributes a large amount of
weight over a small area. Make certain that the
floor is capable of supporting both the weight of the
machine and the operator. The floor should also be
a level surface. If the unit wobbles or rocks once in
place, be sure to eliminate the wobble by using
shims.
WORKING CLEARANCES: It is important to
maintain a free area of 31-1/2” (0.8 m) around the
machine, which is required for the working area. If
any long material is to be cut, it is necessary to
have sufficient room both in front of the machine as
well as behind it for material infeed and outfeed.
OUTLET PLACEMENT: Outlets should be located
close enough to the machine so that the power
cord or extension cord is not in an area where it
would cause a tripping hazard.
DO NOT assemble the machine until you are
certain that the machine is not plugged in and
the power switch is in the OFF position.
DO NOT connect the machine to the power
source until you read and understand the entire
User Manual.
3.4.1 Remove the pallet
The machine is fixed on the pallet by M8 hex bolts.
Before installing, please take off the accessories
on the pallet and in the cabinet. Then move the
machine out after removing the set bolts under the
pallet, as shown in Fig. 6. Locate the machine at
appropriate place.
Fig. 6
3.4.2 Hand-wheel handle installation
Install the handle into the Blade Tilt hand-wheel as
shown in Fig. 7.
Fig. 7
3.4.3 Extension wings installation（Fig.8）
The machine is equipped with a cast iron extension
wing on each side of the main table. The mounting
bolts of extension wings are pre-mounted in the
threaded holes on the main table sides. Install the
extension wings as follows:
1. Remove the screws from the sides of the main
table;
2. Inspect the extension wings and main table
mating surfaces for burrs or foreign materials that
may inhibit assembly; the mating edges of the
tables must be clean and flat, use a wire brush or
sand paper if necessary to clean up the edges;
3. Attach the wings to the main table by using the
screws removed in step 1;
4. Use a straightedge to check whether that the
main table is coplanar with the extension wing. If
not, use a strip of masking tape to shim the
extension wing up or down, as directed by the
arrow in Fig. 8 .
Fig. 8

10
A
3.4.4 Install the rail & extension table
1. Install the rail and extension table as breakdown
shows.
Before tightening the rear rail, check to make sure
the top edge of the rear rail is lower than the T-slot ，
as shown in Fig. 9.
Ensure that the extension table is coplanar with the
main table.
Fig. 9
2. Install the fence on the rail on the right hand side
of the blade as shown in Fig. 10.
If you need to use the fence on the left side of
the blade, remove the knobs (A), as shown in
Fig.10, and move the fence plate and locking
bar to the right side of the fence body, secure
them on the left side of the fence body.
Fig. 10
3. Check the fence parallelism and
perpendicularity （Fig.11）
As shown in Fig.11, after securing the fence,
ensure that the fence is parallel to the miter slot,
which is parallel to blade at any locations. And
make sure that the distance L1 >L2, L1-L2<1/64",
which creates a slightly larger opening between the
fence and the blade, at the rear of the blade, to
reduce the risk of workpiece binding or burning as
it is fed through the cut.
Fig. 11
4. Adjust the parallelism and perpendicularity of
the fence (Fig.12)
If the fence or blade is not parallel to the T-slot, or
the fence is not perpendicular to the table, you can
adjust as following content:
a. Align the the parallelism between the blade
and T-slot.
Before aligning perpendicularity or parallelism of
the fence, you must align the parallelism between
the blade and T-slot, refer to chapter 6.2 Aligning
the Table T-slot Parallel with the Blade.
b. Align the the parallelism between the fence
and T-slot or blade.
By adjusting the set screw (A), you can adjust the
parallelism between fence and blade, also you can
adjust the locking strength. By adjusting the bolt
marked in a circle as shown in Fig. 12, you can
adjust the the perpendicularity between the fence
and table. By adjusting the set screw (B), you can
adjust the sliding smoothness of the fence.
Fig. 12
By adjusting the support screw (not shown) at
the underneath of the fence, you can raise or
lower the fence to ensure that the underneath
of the fence is parallel to the table.
L1
L2

11
3.4.5. Post the tape scale use the pointer
window (Fig.13)
The machine features a Hi-Low fence with two
pointer windows. As shown in Fig.13. The pointer
window (A) is for the lower fence while pointer
window (B) is for the high fence. You can micro-
adjust the position of pointer window by loosening
the screws (C) and (D).
Post the Tape Scale
Place the fence as a high fence, slide the fence
against the saw blade, and lock it in place; Place
the front rail tape scale on the fence tube, make
sure it is parallel with the tube, and the “0” end is
directly under the red line on the pointer window
（B）, lightly mark the “0” location on the tube with
a pencil, then remove the fence; peel the tape and
carefully align the “0” mark on the scale with the
pencil mark you made.
Calibrate the Pointer Window
Place the fence as a high fence, as shown in
Fig.13. Slide the fence against the blade, check
that if the “0” mark is directly under the red line on
the pointer window (B), if any deviation occurs,
loosen the screws (C&D), micro-adjust the
window, so that the red line on the window is
over the “0” mark on the tape, then secure the screws
(C&D).
Place the fence as a lower fence. Slide the fence
against the blade, check that if the “0” mark is
directly under the red line on the pointer window
(A), if any deviation occurs, loosen thescrews,
(C&D), micro-adjust the pointer window, so that the
red line on the window is over the “0” mark on the
tape, then secure thescrews (C&D).
Fig. 13
3.4.6 Install the switch（Fig.14）
The switch is mounted on the lower right side of the
guide tube by using two sets of bolts which are pre-
installed on the guide tube.
Fig. 14
3.4.7 Install the blade
1. Remove the table insert;
2. Rise the arbor all the way up and set the blade
angle at 0º;
3. Remove the arbor nut and arbor flange from the
arbor, slide the saw blade onto the arbor, making
sure the teeth face the front of the saw, then install
the arbor flange and arbor nut onto the blade;
4. Press the arbor lock pin,and use the included
wrench to tighten the arbor nut referto Fig. 15.
Fig. 15

12
3.4.8 Install the blade guard
1. Remove the table insert;
2. Unlockthe handle. Fig. 16
3.4.9 Extraction system
A dust collection device should be used by the
customer ， the dust extraction equipment must
be switched on before commencing machining.
1. Installation of the Dust Outlet (Fig.18)
The dust outlet is pre-connected with the flex pipe
and placed in the cabinet. Disconnect the flex pipe
with the dust outlet and pass the pipe through the
cabinet. Then reconnect the flex pipe with the dust
outlet and secure the dust outlet on the cabinet.
Note: The mounting hardware of the dust outlet is
pre-mounted on the cabinet.
Fig. 16
3. Slide the blade guard spreader all the way down
into the block, then lock the handle.
Fig. 16
4. Slide the blade guard onto the spreader, tighten
the lock knob. Fig. 17
Fig. 17
5. Re-lock the handle.
Check if the saw blade is tightened before
operating the machine.
Give the spreader an upward tug to verify if it is
locked in place.
Fig. 18
2. Installation of the over arm(Fig.19):
a. Fit the bracket (A) to the rear rail with screw (B).
b. Fit the over arm to the bracket (A) with clip (C).
(Total 2 sets of clasps)
c. Connect the pipe (1.5”) provided by us to the
dust outlet as Fig. 22 shows..
Note ： All the hardware here is pre-mounted on the
over arm assembly.
Fig. 19
Requirements for the dust collector:
1. Required air flow: 470 CFM (800 m³/h).
2. Ensure pressure drop of each dust collector
outlet carrying air current speed: 1100Pa
3. Dry chips: 3937 FPM (20 m/s).
4. Wet chips: 5511 FPM (28 m/s). (water content
is equal to 18%)

13
3.4.10 Motor cover installation
Install the motor cover by inserting the door pins
into the hinge sockets on the cabinet as shown in
Fig. 20.
Fig. 20
3.4.11 Electrical installation
Wiring should only be done by professional
electricians.
Always make sure the machine is properly
grounded. All exposed conductive parts should
be connected to the protective ground circuit.
An over-voltage protection device should be
provided by end user.
The circuit breaker shall be installed to supply
electric power to this machine, in order to
protect people against electrical shock due to
incidental contact.
Check that the voltage and frequency required by
the machine, which is shown on the machine’s
name plate, correspond to the electric power
supply voltage and frequency.
Ensure IP54 protection class for the incoming
cable when the finished installation is in place.
Checking:
After finishing wiring in place, at minimum, check
the following items:
1. Check the direction of motor and change the
wiring if necessary.
2. Check the components for defects, such as
damaged cable or plug.
3. Check the function of the “OFF” button.

14
ELECTRICAL DIAGRAM
3HP/230V/50Hz/1PH
Remark:
1. The colour of single core may differ with the illustration above in different areas.
2. Single-phase power supply range: 200-240 V.

15
4. Adjustment
Before operation, Please make adjustments as
followings:
4.1 Adjusting the Rip Fence
Before using the rip fence, the parallelism and
perpendicularity must be aligned correctly. Please
refer to chapter 5.4.4 Install the rail & fence.
4.2 Aligning the Table T-slot Parallel with
the Blade
1. The table T-slot must be aligned parallel with the
blade. Using a combination square measure the
distance from the back edge of the blade to the
table T-slot. Pivot blade forward 180º and re-
measure the distance using the exact same point
on the blade. The difference between both
measurements must be less than 0.2mm. Refer to
Fig. 21.
Fig. 21
2. If an adjustment is necessary, loosen the
screws identified in Fig. 22 which mount the table
to the cabinet. Make the needed adjustment until
both measurements are equal or less than 0.2 mm.
and re-tighten the screws.
Fig. 22
4.3 Adjusting the 45° and 90° Positive
Stops
The tilt mechanism has adjustable stops for 45° and
90°. The machine comes factory-set but should any
positioning deviation of the blade occur, you can re-
adjust the stops. Refer to Fig. 23.
Fig. 23
To adjust the 90° Positive Stop: open the motor cover
on the right side of the machine. Then loosen the
locking nut (A) and adjust the limit screw (B) until it
contacts with the positive stop. Tighten the locking
nut(A).
To adjust the 45° Positive Stop: loosen the screws of
the repair panel on the left side of the machine and
take off the repair panel. Then loosen the locking
nut(C) and adjust the limit screw (D) until it contacts
with the positive stop. Tighten the locking nut(C).

16
4.4 Aligning the Riving Knife with Blade
The riving knife must be aligned with the blade. If
not properly aligned, the riving knife will force the
workpiece sideways during the cut, increasing the
risk of kickback. Place a straightedge against the
blade and the riving knife and check if the riving
knife is in the "alignment zone," refer to Fig. 24.
Fig. 24
If it is not aligned properly, please adjust as
following (Fig. 25):
1. Disconnect the saw from the power source.
2. Remove the table insert.
3. Adjust the set screws (A) in or out until the
alignment is perfectly parallel.
4. Re-install the table insert.
Fig. 25
1. Riving knives shall have a thickness less than
the width of a cut (kerf) and at least 0.2mm
greater than the saw blade plate. As shown in Fig. 26.
Fig. 26
Key:
eriving knife thickness
bsaw blade base
Bkerf (width of saw blade cut)
2.
The distance of the riving knife from the gear rim
must be between 3 mm and 8 mm measured
radially through the center of the saw spindle. As
shown in Fig. 27.
Fig. 27
3.
The highest point of the riving knife must be set
beneath the topmost teeth.
4.5 Calibrating the Saw Blade Angle DRO
(Optional)
1.
Useing the square to adjust the saw blade to 90°.
2.
Press the ZERO button for few second, untill the
number on screen showing 0.
3.
Useing the square to adjust the saw blade to 45°.
4.
Press the END button for few second, untill the
number on screen showing 45.
Fig. 28

17
5. Operations
5.1 Electrical Operation
Two types of the switches are alternative for
your machine, the actual object shall prevail.
Refer to Fig. 28 & Fig.29
“ON” Button: Start the machine.
“OFF” Button: Stop the machine.
Hole for Safety Lock: While not using the
machine, insert the safety pin to prevent
accidental start up.
Fig. 29
5.2 Blade Elevation andTiltingAdjustment
To adjust the blade elevation : Loosen the lock
knob (C) as shown in Fig. 30 and turn the elevation
hand wheel (D). When the desired height is
obtained, re-tighten the knob (C). The blade should
be raised 1/8” to 1/4” above the top surface of the
material being cut.
To adjust the blade tilting : Loosen the lock
knob (B) and turn the hand wheel (A). When the
desired angle is obtained, re-tighten the knob (B).
Refer to Fig. 30.
Fig. 30
6. Maintenance
This table saw has TEFC motor and sealed
lubricated bearings, which requires very little
maintenance other than minor lubrication and
cleaning. Please do the maintenance as following
contents.
LUBRICATION
Clean off the wood chips on the worm gears and
trunnions and apply the grease to keep them
lubricated.
Lubricate once a month.
CLEANING
Clean the wood chips on the table surface and in
the cabinet.
Clean once a day.
CHANGING BELT
Make sure the power cord is disconnected from
the power source!
1. Lower the blade completely, then open the
motor cover (right side), remove the repair panel
(left side), refer to Fig. 31.
2. Loosen the hex bolt that secures the motor and
raise the motor fully to remove tension on the V-
Ribbed belt. Roll the V-Ribbed belt off.
3. Raise the motor and install a new V-Ribbed belt
onto the pulleys, lower the motor to tension the V-
Ribbed belt, then tighten the cap screws.
4. Close the motor cover and repair panel.
Fig. 31

18
7. Trouble Shooting
PROBLEM
SOLUTION
SAW WILL NOT START
1. Saw not plugged in.
2. Fuse blown or circuit breaker tripped.
3. Cord damaged.
1. Plug in saw.
2. Replace fuse or reset circuit breaker.
3. Have cord replaced by a certified electrician.
OVERLOAD KICKS OUT FREQUENTLY
1. Extension cord too long or gauge size too small.
2. Feeding stock too fast.
3. Blade in poor condition (dull, warped, gummed).
4. Blade binding due to misaligned rip fence.
5. Blade binding due to warped wood.
6. Low house current.
1. Replace with adequate size cord
2. Feed stock more slowly.
3. Clean or replace blade.
4. Check and adjust the rip fence. Refer to rip fence
instructions.
5. Select another piece of wood.
6. Contact your electrical company.
DOES NOT MAKE ACCURATE 45 AND 90 RIP CUTS
1. Positive stop(s) not adjusted properly.
2. Tilt angle pointer not set properly.
1. Check blade with square and adjust positive stop.
2. Check blade with square and adjust pointer to zero.
MATERIAL PINCHES BLADE WHEN RIPPING
1. Rip fence not aligned with blade.
2. Warped wood.
1. Check and adjust rip fence.
2. Select another piece of wood.
MATERIAL BINDS ON SPLITTER
1. Splitter not aligned correctly with blade.
1. Check and align splitter with blade.
SAW MAKES UNSATISFACTORY CUTS
1. Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
4. Incorrect blade for work being done.
5. Gum or pitch on table causing erratic feed.
1. Replace blade.
2.Turn blade around.
3. Remove blade and clean with terpentine and steel wool.
4. Change the blade.
5. Clean the table with turpentine and steel wool.
BLADE DOES NOT COME UP TO SPEED
1. Extension cord too light or too long.
2. Low house current.
3. Motor not wired for correct voltage.
1. Replace with adequate size extension cord.
2. Contact your electric company.
3. Refer to motor and /or nameplate.
MACHINE VIBRATES EXCESSIVELY
1. Table not mounted securely to cabinet stand.
2. Stand is on uneven floor.
3. Damaged saw blade.
4. Bad V-Ribbed belt.
5. V-Ribbed belt is not tensioned properly.
6. Improper motor mounting.
7. Loose hardware.
1. Tighten all mounting hardware.
2. Reposition on flat level surface.
3. Replace blade.
4. Replace V-Ribbed belt.
5. Adjust V-Ribbed belt tension.
6. Check and adjust motor mounting.
7. Tighten all nuts, bolts and set screws.

Table Diagram and Part List
213
237
238
239
201
241
240
202
203
207
204
205
206
236
208
235
234
242
209
233
232
210
231
211
230
212
229
221
222
214
219
220
225
224
223
228
227
226
215
216
218
217