Waste king 2000 User manual

INSTALLATION OF CONE SINK INTO DISH OR WORKTABLE

1. (See Figures 1 and 2.) Locate hole center as shown on Figure 2. Cut a “C” (Figure 2) diameter hole in dish or work table, a minimum of 2”

from the inside front edge (operator’s side). Hole can be cut with a “nibbler” after a knockout hole 11/2” diameter has been punched.

2. Lift cone to underside of table with cone flange overlapping all around (Figures 1 and 3).

3. Check alignment of cone spray fittings to be sure they are in the proper position. For 15” and 18” cones, position such that holes are located

to right and left side of operator. (See Figure 7 for location.)

4. Tack weld, spot weld, bolt, or rivet flange of cone sink to underside of dish or work table. If bolted or riveted, smooth top surface and wash-

solder around bolt or rivet heads and sand smooth.

5. Bead weld or solder and wash-solder all around where the table joins flange of cone sink for a clean, watertight, sanitary installation.

6. The cone sink has been designed with the step, as shown in Figure 3. In the welding or soldering operation required to assemble the cone

sink to the dish or work table, every attempt should be made to keep the recessed, flat portion of the cone free of the weld or solder materi-

al. This will minimize the clean-up time required and provide a smooth, flat surface for any cover.

7. Minimum installation criteria:

• Minimum clearance between left and right side of waste disposer and side wall: 18 inches.

• Minimum clearance to back wall: 10 inches.

• No front panel/door between waste disposer installation cavity under a sink/dish table and room.

SPRAY-RINSE INSTALLATION

1. Locate center (Figures 1 and 2).

2. Drill 7/16” diameter hole through center.

3. Assemble 7/8” punch and tighten bolt head, as illustrated,

until the die pierces the stainless steel, leaving a clean

opening of 7/8”.

4. Place body valve and base in position, assemble washer

and locknut as shown in Figure 5.

5. Attach vol-temp assembly to the projecting nipple.

POSITIONING AND INSTALLATION

OF COMMERCIAL DISPOSER

1. Subassemble plumbing for swirl sprays as shown in detail in Figure 6,

and as shown assembled on final unit in Figure 7.

2. Slide Hush Cushion®up over edge of flange on cone sink. The inner

edge of this Hush Cushion®is chamfered to facilitate this operation.

3. Slide one clamp ring over Hush Cushion®, place between two upper beads

and tighten, this firmly attaches the Hush Cushion®to the cone sinks.

NOTE: On the six inch opening only to make certain that the Hush Cushion®

is not mounted upside down, look down into the cone sink from above the

work table and check that the wording is readable on the center plug on the

Hush Cushion®. This reads, “Remove before using”.

COMMERCIAL

DISPOSER MODELS

2000, 3000, 5000

AND 10000

INSTALLATION

INSTRUCTIONS

BEFORE INSTALLING, READ ENTIRE INSTRUCTIONS CAREFULLY.

RISK OF INJURY TO PERSONS FROM HAZARDOUS MOVING PARTS. SERIOUS INJURY POSSIBLE IF

NOT PROPERLY INSTALLED WITH A HOPPER OR A CONE SPECIFIED IN THE INSTRUCTION MANUAL.

IF YOU ARE REPLACING AN OLD DISPOSER GO TO

POSITIONING AND

INSTALLATION OF COMMERCIAL DISPOSER

MODEL 6T

2216 2215 2211

12” CONE 15” CONE 18” CONE

A101/4”11

3/4”13

1/4”

B31/2”3

1/2”3

1/2”

C131/2”16

1/2”19

1/2”

MODEL 9T

2216 2215 2211

12” CONE 15” CONE 18” CONE

A127/8”12

7/8”12

7/8”

B61/8”4

5/8”3

1/8”

C131/2”16

1/2”19

1/2”

FIG. 1 FIG. 2

FIG. 4 FIG. 5

FIG. 3

FIG. 6

BODY

VALVE

7/8” PUNCH

BASE

WASHER

DISH TABLE

CONE SINK

APPROX.

30”

APPROX. 14”

9” MIN. 6” MIN.

2” TO 4”

6”

6-5/8”

No. 9T

SPRAY

RINSE

No. 6T

SINK

HOLE

C DIA.

SPRAY

RINSE

HOLE

LOCKNUT

FLAT PORTION

OF CONE SINK

GLOBE VALVE 1/2”

1/2” COPPER

TUBING

1/2” COPPER

TUBING 1/2” TUBE

FITTING

1/2” TUBE

FITTING

1/2” CLOSE

NIPPLE

NIPPLE 1/2” X 6”

1/2” X 4” NIPPLE

1/2” “T”

1/2” CLOSE NIPPLE

SPRAY RINSE

4. Slide second clamp ring loosely over Hush Cushion®and up to previously tightened clamp ring. Do not tighten.

5. Unscrew legs until there is a space of approximately 1/4” between the top of the upper housing and the Hush Cushion®. Raise disposer until

the upper housing slides into the Hush Cushion®.

Slide the loose clamp ring between the two lower beads on the Hush Cushion®and tighten.

6. Assemble swirl spray or swirl sprays as shown in Figure 8. The method of assembly of the swirl sprays is typical. Other combinations of con-

vertible and fixed swirl sprays are available. The outlet hole of fixed spray head should be horizontal to promote swirling action in cone sink.

(convertible spray see Figure 9.)

7. Connect copper tube or tubes to swirl sprays and bend in gradual curve to connect to fittings in valves. See Figure 7.

8. Thread special nipple into drain outlet, slide hush connector over pipe and assemble and tighten clamp ring in two grooves.

NOTE: ALL PLUMBING AND ELECTRICAL CONNECTIONS SHOULD BE MADE ACCORDING TO LOCAL CODES.

INSTALLATION DIMENSIONS AND DRAINLINE CONNECTIONS

FIG. 7

NOTE:

A globe valve used for metering flow to prevent solenoid

hammering must be installed between solenoid valve and

disposer. See Fig. 7. Any valve ahead of the solenoid valve

must be opened and cause no restrictions.

IMPORTANT! Do not test or run disposer without mini-

mum water flow (see Plumbing Installation) as this will

damage the seal and void the warranty.

NOTE:

Disposer assembly includes disposer, outlet, nipple, Hush

Cushion®, clamps and supporting legs. Other items must be

purchased separately. Items shown in gray in Figure 7 are

available in equipment groups ordered separately.

#9T SPRAY RINSE

(Dotted Outline Illustates 9T Rinse)

MAGNETIC SWITCH

AND REMOTE

PUSH BUTTON

STATION

SYPHON

BREAKER

(Check Local

Code)

1" MIN.

ABOVE

TABLE RIM

1/2" GLOBE

VALVE FOR

METERING*

POWER

SUPPLY

SOLENOID VALVE

1/2" GLOBE VALVE

GATE VALVE

WASTE LINE

3/4" COLD WATER

GATE VALVE

1/2" HOT WATER

SEE FIG. 11

1/2" GLOVE

VALVE

TUBE

CLAMP

RING

MANUAL

SWITCH

ELBOW

TUBE FITTING

HUSH CUSHION¤

APPROX. 40"

HOT WATER

FIG. 8 FIG. 9 CONVERTIBLE SPRAY

AERATOR SPRAY

SPRAY GASKETS

STEEL WASHER

CONICAL –

BRASS WASHERS

NUT

LOCK

NUT

CONICAL

WASHER

TUBING

LOCK

NUT

TUBING

NUT

STEEL WASHERSPRAY HEAD

BRASS

WASHERS

SPRAY HEAD

GASKET

The convertible spray

should be located

opposite the direction

of travel of dishes in

scrapping operation.

FIG. 10 FIG. 11

DIMENSIONS

2000-1 2000-3 3000-3 5000-3 5000-38 10000-3

323/8 - 351/8323/8 - 351/8323/8 - 351/832 7/8 - 353/83261/64 - 3529/64 3261/64 - 3529/64

B215/16 209/16 2215/32 221/22237/64 2337/64

C65/865/865/865/865/865/8

D6666 8 8

E161/4161/417 15/16 17 19/64 17 3/817 3/8

F16 16 161/8165/816 23/32 16 23/32

253/4 - 281/2253/4 - 281/2253/4 - 281/2261/4 - 283/42621/64 - 2853/64 2621/64 - 2853/64

H51/851/867/887/16 87/16 87/16

J53/453/487/888 8

K25/825/833/843/443/443/4

L67/16 67/16 713/16 1013/16 1013/16 10 13/16

TRAP

WALL

DISPOSER

If space between dis-

poser and wall is

insufficient to allow

for installation of trap,

waste line may have

to be at an angle to

the wall as shown.

G* B

G minus B

Water

Inlet

Drain

Slope =

1/4”Per

Foot

Sink

Flange

Legs are adjustable beyond the minimum shown in the screw adjustment. 2”clearance must be maintained beneath unit for proper ventillation.

PLUMBING INSTALLATION

NOTE: Refer to FIgure 10 for installation dimensions and drainline connections.

1. Plumb unit using valves and fittings as shown typically in Figure 7.

NOTE: Syphon breaker, available as option item, is approved in most areas. Check local code to be sure it conforms in your area.

2. When overhead spray rinse is used, split the incoming 3/4”cold water into two 1/2”lines and connect one to the 1/2”“T”at the bottom of the

unit and the other to the globe valve on the cold water side of the spray rinse. Connect one 1/2”hot water line to the globe valve on the hot

water side of the spray rinse.

3. On models 3000, 5000, and 10000 connect 3”drain to the hush connector. Drain line must have a minimum of bends. The unit is

equipped with a drain outlet designed for a connection to a conventional 3”trap. For model 2000 drain line and trap will be 2”.

IMPORTANT! Before installing the Waste King®disposer, the connecting waste line must be cleaned out all the way to the connecting sewer

main. DO NOT CONNECT INTO GREASY TRAP.

The trap may be connected to a 3”branch waste line running directly into the stack. For model 2000, branch waste line can be 2”. A mini-

mum slope of 1/4”per foot of run of waste line is recommended. Limit the horizontal drain line to a 15 foot run free of turns; then, using a

long 45°“Y”, connect to a 3”or 4”horizontal line or stack. Recessed thread fittings must be used throughout and all pipe ends should be

carefully reamed. A minimum number of elbows, tees, etc., reduce the possibility of plumbing stoppages. Water is injected to underside of

table chamber through a control that allows approximately 4 gallons per minute flow. Do not restrict or alter this control as it is necessary to

properly clean the inside of the unit.

IMPORTANT: If unusual sewer conditions exist (too many bends or too long to main), if the water pressure is low for application resulting in low

water flow rate, or if high percentage of leafy and/or paper material is included in food waste, serious consideration should be given to the use of

a time delay and water injector into the sewer to overcome stoppages. Under such conditions a larger size cold water line should be used along

with larger solenoid valves and syphon breakers. (Parts and data available from factory.)

*Minimum Water Flow RATE Used with Model: 2000 and 3000 –10 gallons per minute. 5000 and 10000 –14 gallons per minute.

TESTING

IMPORTANT! Do not test or run disposer without minimum water flow (see Plumbing Installation) as this

will damage the seal and void the warranty.

1. Test assembly for leaks: a. Where cone sink joins table

b. Where disposer joins cone sink

c. At all piping connections

d. Where swirl spray fittings connect

2. After plumbing and electrical connections are made, turn on disposer to be sure all parts are in working order and that the disposer turntable

rotates clockwise when viewed from above. Open valve in vacuum breaker line and, using globe valves in plumbing assembly (Refer to

Figure 6), adjust so that water swirls around just below the rim of the cone sink. Leave valves open in these positions.

NOTE: When the convertible swirl spray is used to remove food waste from dishes, adjust the flow to provide a convenient combination of

anti-splash and high flow volume characteristics (top of flume approximately 3”above cone sink). These combinations provide a flow of

approximately 8 gallons of water per minute.

3. Replace cover, retest for leaks and turn unit off.

4. Unit is now ready for operation.

OPERATING INSTRUCTIONS

IMPORTANT! Do not test or run disposer without minimum water flow (see Plumbing Installation) as this

will damage the seal and void the warranty.

1. Push “start”button. Be sure unit is running and water is flowing before any waste is fed into the disposer. Do not pack food waste into unit.

Do not dump garbage can loads directly into unit. Feed waste in gradually.

2. DO NOT ALLOW GLASS, METAL OR CROCKERY TO ENTER. IF THIS OCCURS, STOP THE UNIT AND REMOVE SUCH MATERIAL.

3. IF THE MOTOR STOPS, push stop button. Remove any waste material which caused stoppage. Check the turntable to see that it will turn

freely. Wait three minutes, push red reset button firmly (LOCATED ON JUNCTION BOX OF MOTOR). Then push “start”button.

4. If the motor hums and the turntable does not rotate freely, there is usually a jamming obstruction, such as metal. STOP UNIT. With a suitable

bar or stick, pry against one of the impellers and rotate the turntable in a counterclockwise direction. When the turntable is free, REMOVE

THE BAR AND THE OBSTRUCTION MATERIAL BEFORE RESTARTING UNIT. CAUTION –LOSS OF ONE PHASE IN THREE PHASE

UNITS (if one fuse blows while running) WILL CAUSE MOTOR TO LABOR AND HEAT. PROLONGED OPERATION WILL DAMAGE THE

MOTOR.

5. If the motor remains silent after resetting the overload protector (as instructed in item 3 above) and the turntable rotates freely, check the

electric fuses and complete electrical circuit.

6. ALWAYS ALLOW THE DISPOSER AND THE WATER TO RUN FOR THREE MINUTES AFTER EACH OPERATION to keep the unit clean

and to flush all food waste out of the drain lines. THIS IS IMPORTANT!

CAUTION: ALWAYS TURN THE DISPOSER OFF AND LET IT COME TO A STANDSTILL BEFORE PUTTING YOUR HAND INTO THE HOP-

PER OR NEAR THE GRINDING CHAMBER. DO NOT LOOK FOR CAUSE UNTIL STARTING CONTROL IS TURNED OFF.

ELECTRICAL INSTALLATION

1. Use waterproof conduit and make all electrical connections according to local codes.

2. Wire three phase units using manual switches as shown in wiring diagram, Figure 12.

560P333P02 REV B

4240 E. La Palma Avenue, Anaheim, CA 92807 •(800) 454-4423 •fax (800) 246-3245 •www.wasteking.com

MANUAL SWITCH

MODEL VOLTS WK PART NO.

2000 208-240 2420

2 HP 460 2420

3000 208-240 2421

3 HP 460 2421

5000 208-240 2421

5 HP 460 2421

MAGNETIC SWITCH

MODEL VOLTS WK PART NO.

2000 208-240 2416

2 HP 460 2417

3000 208-240 2416

3 HP 460 2417

5000 208-240 2416

5 HP 460 2417

10000 208-240 2416

10 HP 460 2417

FIG. 12 WIRING FOR THREE PHASE UNITS WITH MANUAL SWITCH

FIG. 13 WIRING FOR THREE PHASE UNITS WITH MAGNETIC SWITCH

NOTES:

1. Motor wired at Factory for 208-240 volts.

For 460 volts, connect motor wires as

shown inside of motor junction box cover.

2. Interchange T1 and T3 to reverse rotation.

3. Magnetic and manual starters, supplied

by Waste King do not require heaters to

complete the circuit. Disposers have

built-in overload protection.

NOTES:

1. Motor wired at Factory for 220-240

volts. For 110-120 volts, connect motor

wires as shown inside of motor junction

box cover.

2. Magnetic and manual starters, supplied

by Waste King do not require heaters to

complete the circuit. Disposers have

built-in overload protection.

NOTES:

1. Motor wired at Factory for 208-240 volts.

For 460 volts, connect motor wires as

shown inside of motor junction box cover.

2. Interchange T1 and T3 to reverse rota-

tion.

3. Magnetic and manual starters, supplied

by Waste King do not require heaters to

complete the circuit. Disposers have

built-in overload protection.

MANUAL SWITCH

MODEL VOLTS WK PART NO.

2000 110-120 2420

2 HP 220-240

L-1 L-2

T-1 T-2

L-3

T-3

T-3 L-3

T-2 L-2

T-1 L-1

THESE TERMINALS MAY BE

LABELED T4 OR L4

POWER SUPPLY -

FUSE PER

LOCAL CODE

SOLENOID RATED VOLTAGE

TO MATCH LINE VOLTAGE

MOTOR JUNCTION BOX

L1 L2 L3

T1 T2 T3

SWITCH START - STOP

(MOUNT NEAR UNIT)

COIL RATED

VOLTAGE TO

MATCH LINE

VOLTAGE

POWER SUPPLY -

FUSE PER LOCAL CODE.

MOTOR: CONSULT CHART FOR COR-

RECT MAGNETIC SWITCH

SOLENOID-RATED

VOLTAGE TO MATCH

LINE VOLTAGE

SWITCH BOX ON

FRONT OF UNIT

START

STOP

CLOCKWISE

ROTATION

TURNTABLE ROTATION

AS VIEWED FROM THE TOP

FIG. 14 WIRING FOR SINGLE PHASE UNITS WITH MANUAL SWITCH

L-1 L-2

T-1 T-2

POWER SUPPLY -

FUSE PER

LOCAL CODE

SOLENOID RATED VOLTAGE

TO MATCH LINE VOLTAGE

MOTOR JUNCTION BOX

L1 L2

T1 T2

CLOCKWISE

ROTATION

TURNTABLE

ROTATION

AS VIEWED

FROM THE TOP

SEE CHART FOR

APPROPRIATE SWITCH

CLOCKWISE

ROTATION

TURNTABLE

ROTATION

AS VIEWED

FROM THE TOP

COMMERCIAL

by Anaheim Manufacturing

560P315P01 REV A

4240 E. La Palma Avenue, Anaheim, CA 92807 • (800) 454-4423 • Fax (800) 246-3245 • www.wasteking.com

IMPORTANT

OPERATING INSTRUCTIONS

NOTICE: These operating instructions should

be permanently mounted in an easy-to-read

location. Proper operation can greatly improve

the life and efficiency of your equipment.

1. THE WASTE KING COMMERCIAL DISPOSER OPERATES EFFICIENTLY ONLY WHEN SUFFICIENT WATER FLOWS INTO IT.

IMPORTANT - Do not test or run disposer dry as this will damage the seal and void the warranty.Open globe valves

so that water swirls around cone just below rim. Leave globe valves in this position. (Check water flow in cone with cover off.)

2. Push “START” button or SWITCH and be sure unit is running before any waste is fed into it. Feed food waste in gradually.

Do not pack food waste into unit. Do not dump garbage can loads directly into unit.

3. DO NOT ALLOW GLASS, METAL, WOOD, TABLEWARE, CROCKERY OR ANY OTHER NON-FOOD WASTE MATERIAL TO

ENTER. If this occurs, STOP THE UNIT AND REMOVE SUCH MATERIAL.

4. IF MOTOR STOPS, PUSH “STOP” BUTTON OR SWITCH. Remove any waste material which caused stoppage. Check the

turntable to see that it will turn freely. Wait fifteen minutes, push “RED RESET BUTTON” firmly (located on the top of junction

box). Motor will start when “START” button or Switch is pushed.

5. If the motor hums and the turntable does not revolve freely, there is usually an obstruction. PUSH “STOP” BUTTON

or Switch. With a suitable bar or stick, pry against one of the impellers and rotate the turntable in a counterclockwise

direction. When turntable is free, REMOVE THE BAR AND OBSTRUCTING MATERIAL BEFORE PUSHING “START”

BUTTON OR SWITCH.

6. If motor remains silent after resetting the red reset button (“overload protector” as instructed in Item 4 above) and the

turntable rotates freely, check the electric fuse and the complete electrical circuit.

7. ALWAYS ALLOW THE DISPOSER AND THE WATER TO RUN FOR 3 MINUTES after each disposer operation to keep the

unit clean and to flush all food waste out of the drain lines. THIS IS IMPORTANT. A Time Delay Kit to automatically continue

water flow for a given period of time after the unit is turned off is available through authorized Waste King Service Agencies.

8. ALWAYS DISCONNECT POWER BEFORE PUTTING YOUR HAND INTO THE GRINDING CHAMBER.

9. DO NOT HOSE DOWN DISPOSER.

If you should require service call your authorized WASTE KING service agency.

LOCAL SERVICE AGENCY

PROPER USE OF ALL PURPOSE ASSEMBLIES

For those who prefer a scrap block type

of operation.

Soiled Dishes

Silver Guard

Scrap Ring

Prerinse Dishes

Scrap Ring only

Minimum Silver Guard

protection.

NOTE:

Rotation of turntable viewed

from sink.

READ ALL INSTRUCTIONS CAREFULLY BEFORE OPERATING

INSTALLATION

INSTRUCTIONS

560P402P01 REV A

BEFORE INSTALLING, READ ENTIRE INSTRUCTIONS CAREFULLY

4240 E. La Palma Avenue, Anaheim, CA 92807 • (800) 454-4423

(PER U.L. 430)

FOR UNREINFORCED FLAT SURFACES:

CAST METAL: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .NOT LESS THAN 1/8” (3.2 mm) THICK

MALLEABLE IRON: . . . . . . . . . . . . . . . . . . . . . . . . .NOT LESS THAN 3/32” (2.4 mm) THICK

DIE-CAST METAL: . . . . . . . . . . . . . . . . . . . . . . . . . .NOT LESS THAN 5/64” (2.0 mm) THICK

Metal of lesser thickness but not less than 3/32 inch (2.4mm), 1/16 inch (1.6mm) and 3/64 inch

(1.2mm) respectively, may be acceptable provided that the surface under consideration is: curved,

ribbed, or otherwise reinforced to provide mechanical strength or of a size or shape that provides

mechanical strength equivalent to that required.

Metal of lesser thickness may be acceptable when the following factors are taken into account:

A. MECHANICAL STRENGTH

B. RESISTANCE TO IMPACT

C. MOISTURE-ABSORPTION PROPERTIES

D. COMBUSTIBILITY

E. RESISTANCE TO CORROSION, AND

F. RESISTANCE TO DISTORTION AT TEMPERATURES TO WHICH THE

ENCLOSURE MAY BE SUBJECTED UNDER CONDITIONS OF

NORMAL OR ABNORMAL USE.

FOR A NON-METALLIC ENCLOSURE, ALL OF THESE FACTORS ARE TO BE

CONSIDERED WITH RESPECT TO THERMAL AGING.

SHEET METAL:

In addition to the above factors an enclosure of sheet metal shall be determined with respect to size

and shape, thickness of metal, and acceptability for the application, considering the intended use of the

disposer.

Generally, the use of sheet steel, having a thickness less than 0.0026 inch (0.66mm) if uncoated or

0.029 inch (0.74mm) if galvanized, or of nonferrous sheet metal having a thickness less than 0.036

inch (0.91mm) is not acceptable other than for the relatively small areas or for surfaces that are curved

or otherwise reinforced.

Sheet metal to which a wiring system is to be connected in the field shall have a thickness not less

than 0.032 inches (0.81mm) if uncoated steel, not less than 0.034 inches (0.86mm) if galvanized steel,

and not less than 0.045 inches (1.14mm) if nonferrous.

GUIDELINES FOR

FIELD CONSTRUCTED

ENCLOSURES

Waste King disposers are shipped with the legs fully adjusted (minimum “G” dimension in the

chart below). Please follow adjustment procedure to increase unit height. For installations where the

disposer is too tall, disposer legs may be modified with no loss of range.

Note: minimum of 2” (51mm) clearance beneath the motor must be allowed for proper motor

ventilation.

ADJUSTMENT PROCEDURE

1. Unscrew toe to achieve the desired unit height (3” (76mm)screw adjustment max).

MODELS:

2000-1, 2000-3

and 3000-3

DISPOSER LEG

ADJUSTMENT AND

MODIFICATION

INSTRUCTIONS

560P304P01 REV A

3.0" (76mm) ADJUSTMENT MAX.

TOE UPPER LEGGLIDE

1.0" (25mm)

BEFORE INSTALLING, READ ENTIRE INSTRUCTIONS CAREFULLY

4240 E. La Palma Avenue, Anaheim, CA 92807 • (800) 454-4423

MODIFICATION PROCEDURE

1. Remove the plastic glide from the toe section.

2. Measure the desired cut-off distance from open

end and mark the toe.

3. Using a pipe cutter or hacksaw make a square

cut-off at the mark.

4. Deburr the cut and reinstall the plastic glide.

“G” Inches(mm) Maximum Cut-off

Inches(mm)

Unmodified Modified

25.7 (653) 25.2 (640)

to to 0.5 (13)

28.7 (729) 28.2 (716)

SINK FLANGE

2.0" (51mm) MIN

“G”

Waste King disposers are shipped with the legs fully adjusted (minimum “G” dimension in the

chart below). Please follow adjustment procedure to increase unit height. For installations where the

disposer is too tall, disposer legs may be modified with no loss of range.

Note: minimum of 2” (51mm) clearance beneath the motor must be allowed for proper motor

ventilation.

ADJUSTMENT PROCEDURE

1. Unscrew toe to achieve the desired unit height (2.5” (64mm)screw adjustment max).

MODELS:

5000-3, 5000-38

and 10000-3

DISPOSER LEG

ADJUSTMENT AND

MODIFICATION

INSTRUCTIONS

560P304P02 REV A

BEFORE INSTALLING, READ ENTIRE INSTRUCTIONS CAREFULLY

4240 E. La Palma Avenue, Anaheim, CA 92807 • (800) 454-4423

MODIFICATION PROCEDURE

1. Remove the plastic glide from the toe section.

2. Measure the desired cut-off distance from open end and mark the toe.

3. Using a pipe cutter or hacksaw make a square cut-off at the mark.

4. Deburr the cut and reinstall the plastic glide.

“G” Inches(mm) Maximum Cut-off

Inches(mm)

Model Unmodified Modified

26.25 (667) 24.75 (628)

5000-3 to to 1.5 (38)

28.75 (730) 27.25 (692)

26.38 (670) 24.88 (632)

5000-38 to to 1.5 (38)

28.88 (733) 27.38 (695)

26.38 (670) 25.88 (657)

10000-3 to to 0.5 (13)

28.88 (733) 28.38 (721)

SINK FLANGE

2.0" (51mm) MIN

“G”

TOE UPPER LEGGLIDE

2.5"

(64mm)

ADJUSTMENT

3.0”

(76mm)

WITHIN THE U.S.A. AND CANADA OUTSIDE THE U.S.A. AND CANADA

WASTE KING COMMERCIAL

FOOD WASTE DISPOSERS

Models 500, 750, 1000, 1250, 1500, 2000, 3000, 5000, 10000

ONE YEAR WARRANTY

This appliance is warranted to be free of manufacturing defects in

workmanship and material for one full year beginning from the date of original

purchase. Any part found to be defective will be replaced free of charge.

Service labor is included. Parts wear is not considered a defect.

This warranty is for products purchased and retained in the 50 states of the

United States of America and Canada. This warranty is VOID if the appliance

is moved after the original installation. Should the appliance be sold by the

original purchaser during the warranty period, the new owner continues to be

protected with the appliance in the same location only, until the expiration

date of the original purchaser’s warranty period.

This warranty shall not apply if service is provided by anyone other than a

Factory Authorized Service Agency. Nor will the warranty apply to damage

resulting from accident, abuse, failure to follow operating instructions,

alteration, or if the installation does not comply with our installation instructions

or local building codes.

HOW TO OBTAIN SERVICE

For service, contact the factory at 800-454-4423 for a referral to the nearest

factory authorized service agency.

We want you to remain a satisfied customer. If a problem does come up that

cannot be resolved to your satisfaction, please let us know. Write: National

Service Manager, at the address shown below or phone. Please be sure to

include the model number, serial number and date of original purchase.

WASTE KING COMMERCIAL

WARRANTY DEPARTMENT

4240 E. LA PALMA AVENUE

ANAHEIM, CALIFORNIA 92807

800-454-4423

www.wasteking.com

WASTE KING COMMERCIAL

FOOD WASTE DISPOSERS

Models 500, 750, 1000, 1250, 1500, 2000, 3000, 5000, 10000

ONE YEAR WARRANTY

This appliance is warranted to be free of manufacturing defects in

workmanship and material for one full year beginning from the date of original

purchase. Any part found to be defective will be replaced free of charge.

Labor is not included. Parts wear is not considered a defect.

This warranty shall not apply to damage resulting from accident, abuse,

failure to follow operating instructions, alteration, or if the installation does not

comply with our installation instructions or local building codes.

This warranty is for products purchased and retained outside of the United

States of America, the District of Columbia and Canada.

HOW TO OBTAIN SERVICE

For warranty consideration, contact the dealer from whom you purchased the

appliance or write to us at the address shown below.

We want you to remain a satisfied customer. If a problem does come up that

cannot be resolved to your satisfaction, please let us know. Write: National

Service Manager, at the address shown below or phone. Please be sure to

include the model number, serial number and date of original purchase.

WASTE KING COMMERCIAL

WARRANTY DEPARTMENT

4240 E. LA PALMA AVENUE

ANAHEIM, CALIFORNIA 92807

U.S.A.

PHONE 01-01-714-524-7770

FAX 01-01-714-996-7073

www.wasteking.com

560P303P01

REV 12/97