Watco Innovator CableFlex 928 Instruction Manual

13
14
15
19
14
16
16
WATCO MANUFACTURING COMPANY
Instructions for Installing Watco Innovator®Cable Bath Wastes
Models: Watco CableFlex™: 928, 938, 948 – Watco Cable: 970, 980, 990 – Half Kits: 971, 981, 991
© 2011 Watco Manufacturing Company Page 1 970INST Rev. 4/11
3
Figure 2
Figure 3
Figure 4
19
20
21
22
24 25
26
21
22
Figure 1
Figure 6
Figure 5 Continued next page.
13
12
11
Step 1: Cut the 1½” Schedule 40 (or Flexible PVC) overow pipe and drain pipe (Items 14 and 16) to the
desired lengths to t the tub.
Step 2: Using standard solvent cement procedures, assemble the bath drain pipe and ttings (Items 13-16, and 19).
DO NOT LET SOLVENT CEMENT FLOW INSIDE THE OVERFLOW OR DRAIN ELBOWS PAST THE
SOCKET! Any excess glue will prevent the bath waste from operating.
Step 3: Place the thick foam gasket (Item 12) onto the overow elbow (Item 13).
The testing membrane will still be attached. Thick-walled tubs will require the
thin gasket (Item 11).
Step 4: Insert the overow elbow and
foam gasket assembly through the tub
overow hole from the back of the tub
(Figure 1).
Step 5: Screw on the overow elbow (OE) nut (Item 3)
from inside of the tub (Figure 2). HAND TIGHTEN
ONLY until the nut is snug and the gasket is only slightly
compressed against the back of the tub. You must get a
minimum of 1½ turns when installing the nut. If there are
not enough threads sticking through the tub to get the nut
installed, remove the thick gasket (Item 12) and replace it
with the thin gasket (Item 11).
Step 6: Secure the drain elbow (Item 19) and drain
ange gasket (Item 20) under the tub by screwing
in the strainer body (Item 21) through the tub
drain hole from inside the tub (Figures 3 and 4).
If desired, a putty or sealant may be used between
the ange of the strainer body and the tub.
CAUTION: Do not use linseed oil based putty
products. Use only thread compounds specically
intended either for ABS or PVC assembly.
If the bath waste will not be pressure tested, skip to step 8.
Step 7: Screw the strainer test plug (Item 26) into the strainer
body Item 21) and test the system (Figure 5).
Step 8: After the pressure testing is complete, remove
the test plug (Item 26). Cut away and discard the orange
test membrane from the overow elbow (Figure 6). Use
caution not to damage internal parts on the inside of the
overow elbow.

1
2
4
7
6
3
5
8
13
Watco Innovator®Cable Bath Wastes
Installation Instructions Continued
© 2011 Watco Manufacturing Company Page 2 970INST Rev. 4/11
Figure 7
Figure 8
Figure 9
Figure 12
Figure 11
WATCO MANUFACTURING COMPANY
1220 South Powell Road
Independence, MO 64057-2724
Phone: [phone] • 800-821-8576
Fax: [phone] • 800-399-2826
www.watcomfg.com
Figure 10
19
20
21
22
24 25
Step 1: Remove
stopper seal.
Step 2: Slide Theft-
Resistant device into
stopper slot.
Step 3: Replace
stopper seal.
Step 4: Insert stopper shaft into strainer body, pushing it in until the hook
on the Theft-Resistant device snaps into place under the strainer body.
If installing the Theft-Resistant Option:
Step 9: Select the faceplate adapter (Item 5, 6, or 7) that leaves
the desired gap between the tub wall and the edge of the faceplate
(Item 2). (See included adapter selection instruction sheet.)
Place adapter onto the drive shaft (Item 8) (Figure 7). If you have
selected an adapter that is too short, the spacer tabs on the inside of
the faceplate will rub on the OE nut (Item 3), and the adapter screw
hole will not line up with the faceplate screw hole.
Once the desired faceplate adapter is determined, secure the
faceplate adapter to the drive shaft using the screw provided (Item 4)
(Figure 8).
Secure the faceplate (Item 2) to the faceplate adapter
(Figure 9) using either the faceplate screw (Item 1)
(Figure 10). (Leave the plastic sleeve on threads to help
align the screw.)
or the optional ADA handle.
Tighten the faceplate screw until it is ush with the faceplate and snug
(or if using the handle, until it is snug). DO NOT OVERTIGHTEN.
Step 10: Rotate the faceplate CLOCKWISE to the fully-closed position. Install the core
guide (Item 22) into the strainer body using a screwdriver or 7/16” socket (Figure 11).
(See core guide instruction card included with kit.) The core guide should be screwed in
until it is snug against the bottom of the drain elbow. Insert the stopper (Item 24) into the
core guide (Item 22) (Figure 12).
Step 11: Test the cable unit for proper operation. In the fully-closed position, with the
faceplate (Item 2) rotated clockwise, the stopper (Item 25) should rest and seal on the
strainer body ange. In the fully-open position, with the faceplate (Item 2) rotated
counterclockwise past the click, the stopper should open to a height of ½” - ¾” above the strainer body ange. The plastic
cable core should move freely inside the core guide (Item 22) when the faceplate is turned. Adjustments to the open height
can be made using the stopper adjustment screw (Item 24).