Water Depot Platinum WD SP35BFJCT User manual

wd-2

wd-4

wd-5

wd-6

wd-7

wd-8

wd-9

wd-10

wd-11

wd-12

wd-13

wd-14
Part # Tank Size (DxH) Media Volume (ft3) Service Flow Rate (GPM)
WD SP35BFJCT 10”x44” 1.0 6.0
WD SP46BFJCT 10”x54” 1.5 9.0
WD SP56BFJCT 10”x54” 2.0 12.0
WD SP66BFJCT 12”x52” 2.5 15.0
Table below contains a summary of specifications for the control valve and bypass valve.
QUICK REFERENCE SPECIFICATIONS
CLASSIFICATION: Demand initiated regeneration (metered)
OPERATING PRESSURE: 20-100 psi (1.4 - 7.0 kg/cm2)
OPERATING TEMPERATURE: 35 - 100 F0 (1-370C)
VALVE SIZE: 1”
BYPASS VALVE: 3/4” OR 1” NPT
BRINE TANK DIMENSIONS: 14” X 14”
REGENERATION: Downflow
ELECTRICAL SPECIFICATIONS
Controller Operating Voltage: 12 VAC
Input Supply Frequency: 60hz
Motor Input Voltage: 12 VAC
Electronic Operating Voltage: 3.5 VAC
Transformer Output Voltage: 12 VAC - 400ma
Transformer Input: 115 VAC

wd-15
Service flow rate 1” 27 gpm (102.2 lpm) @ 15 psig (103 kPa) drop
Backwash flow rate 1” (includes bypass) 27 gpm (102.2 lpm) @ 25 psig (172) kPa) drop
Service Flow Rate 1.25” (includes meter) 34 gpm (128.7 lpm) @15 psig (103 kPa) drop
Service Flow Rate 1.25” (includes meter & bypass) 32 gpm (121.1lpm) @ 15 psig (103 kPa) drop
Backwash flow rate 1.25” 32 gpm (121.1 lpm) @25 psig (172 kPa) drop
Backwash flow rate 1.25” (includes bypass) 30 gpm 9113.5 lpm) @ 25 psig 9172 kPa) drop
Minimum/Maximum Operating Pressures 20 psi (138 kPa) - 125 psi (862 kPa)
Minimum/Maximum Operating Temperatures 40°F (4°C) - 110°F (43°C)
AC Adapter:
Supply Voltage
Supply Frequency
Output Voltage
Output Current
U.S. INTERNATIONAL
120 V AC 230 V AC
60 Hz 50 Hz
12 V AC 12 V AC
500 mA 500 mA
Regenerant Refill Rate 0.5 gpm (1.9 lpm)
Injectors See Injector Graphs
Drain Line Flow Controls See Table 7
Inlet/outlet Fitting Options (a) 1” NPT elbow which has a unique drill out
feature to allow a 1/4” NPT connection to the
inlet and/or outlet
(b) 3/4” &1” PVC solvent weld fitting
(c) 1” straight brass sweat fitting
(d) 3/4” straight brass sweat fitting
(e) 1” plastic male NPT fitting
(f) 1 1/4” plastic male NPT fitting
(g) 1” plastic make BSPT fitting
(h) 1 1/4” plastic make BSPT fitting
Distributor Tube Opening WS1HR&HS Valve 1.05” outside diameter (3/4” NPS)
Distributor Tube Opening WS1.25HR&HS Valve 1.32” outside diameter (3/4” NPS)
32 mm outside diameter
Tank Thread 2 1/2” - 8 NPSM
Control Valve Weight 4.5 lbs. 2.0 kg
PC Board Memory Nonvolatile EEPROM
(electrically erasable programmable ready only
memory)
Compatible with regenerants/chemicals Sodium chloride, potassium chloride, potassium
permanganate, sodium bisulfite, chlorine and
chloramines.

wd-16
1. Timer does not display time of day a. AC adapter unplugged a. Connect Power
b. No electric power at
outlet
b. Repair outlet or use working
outlet
c. Defective AC adapter c. Replace AC adapter
d. Defective PC board d. Replace PC board
2. Timer does not display correct a. Switched outlet a. Use uninterrupted outlet
b. Power outage b. Reset time of day
c. Defective PC board c. Replace PC board
3. No softening/filtering display when
water is flowing
a. Bypass valve in bypass
position
a. Put bypass valve in service
position
b. Meter connection
disconnected
b. Connect meter to PC board
c. Restricted/stalled meter
turbine
c. Remove meter and check for
rotation or foreign material
d. Defective meter d. Replace meter
e. Defective PC board e. Replace PC board
4. Control valve regenerates at
wrong time of day
a. Power outages a. Reset control valve to correct
time of day
b. Time of day not set
correctly
b. Reset to correct time of day
c. Time of regeneration c. Reset regeneration time
d. Control valve set at
“on 0” (immediate
regeneration)
d. Check control valve set-up
procedure regeneration time
option
e. Control valve set at
NORMAL + on 0
e. Check control valve set-up
procedure regeneration time
option
5. ERROR followed by code number
ERROR code: 1001 - Unable to
recognize start of
regeneration
ERROR code: 1002 - Unexpected
Stall
ERROR code: 1003 - Motor ran too
long, timed out trying
to reach next cycle
position
a. Control valve has just
been serviced
a. Press NEXT and REGEN for 3
seconds or unplug power source
jack (black wire) and plug back
in to reset control valve
b. Foreign mater is lodged
in control valve
b. Check piston and spacer stack
assembly for foreign matter.
c. High drive forces on
piston
c. Replace piston (s) and spacer
stack assembly
d. Control valve piston not
in home position
d. Press NEXT and REGEN for 3
seconds or unplug power source
jack (black wire) and plug back
in to reset control valve

wd-17
ERROR code: 1004 - Motor ran to long,
timed out trying to reach
home position
If other ERROR codes display contact the
factory.
e. Motor not inserted fully to
engage piston, motor wires
broken or disconnected
motor failure
e. Check motor and wiring. Replace
motor if necessary.
f. Drive gear label dirty or
damaged, missing or
broken gear
f. Replace or clean drive gear
g. Drive bracket incorrectly
aligned to back plate
g. Reset drive bracket property
h. PC board is damaged or
defective
h. Replace PC board
i. PC board incorrectly
aligned to drive bracket
i. Ensure PC board is correctly
snapped on to drive bracket
6. Control valve stalled in regeneration a. Motor not operating a. Replace motor
b. No electric power at outlet b. Repair outlet or use working outlet
c. Defective AC adapter c. Replace AC adapter
d. Defective PC board d. Replace PC board
e. Broken drive gear or drive
cap assembly
e. Replace drive gear or drive cap
assembly
f. Broken piston retainer f. Replace drive cap assembly
g. Broken main regenerant g. Replace main regenerant piston
7. Control valve does not regenerate
automatically when REGEN button is
depressed and held
a. AC Adapter unplugged a. Connect AC adapter
b. No electric power at outlet b. Repair outlet or use working outlet
c. Broken drive gear or drive
cap assembly
c. Replace drive gear or drive cap
assembly
d. Defective PC board d. Replace PC board
8. Control valve does not regenerate
automatically but does when REGEN
button is depressed
a. Bypass valve in bypass
position
a. Put bypass valve in normal
operating position
b. Meter connection
disconnected
b. Connect meter to PC board
c. Restricted/Installed meter
turbine
c. Remove meter and check for
rotation or foreign matter
d. Defective meter d. Replace meter
e. Defective PC board e. Replace meter
9. Time of day flashes on and off a. Power has been more than
two hours, the AC adapter
was unplugged and then
plugged back into the wall
outlet, the AC adapter
plug was unplugged and
then plugged back into
the board or the NEXT
and REGEN buttons were
pressed to reset the valve.
a. Reset the time of day

wd-18

wd-19

wd-20