Waylens Secure 4K User manual

Connect your Secure 4K
using this WiFi SSID and password,
making sure to keep them in a safe
place for future reference.
© 2020 Waylens, Inc. All rights reserved.
4K

Placement
Guide
Power Cord
Installation
Guide
What’s included with the Secure4K
Secure4K
Camera & Dock
Secure4K
Mount Plate
& Adhesive
Please ensure the Secure4K and any necessary power components are secured and out of reach of
passengers, especially young children and pets.
4K
1 2
Option A
OBD-II Power Cord
Option B
Direct Wire Power Cord
DMS Module
(Optional)
Power Cord
Locker
Tamper
Tape

Status LED mode
Camera Mount Screw
microSD Card Slot
Remote Camera
Cable Holder
Reset Button
USB Type-C Power
Waylens Button
Cabin Lumination
Remote Camera
Cable Socket
SIM Card Slot
Status LED
Remote Camera
Cable Holder
Solid Green
Solid Blue
Solid red
Blinks Blue
Blinks Blue and Red
Power On
Idle
Recording
Firmware Updating
Error
Secure4K Overview
Click x1
Click x3
Press for 2s
Press for 4s
Flip on WiFi On/Off
Flip on WiFi Direct Mode
Flip on Recording
Restart the camera
Using the Waylens Fleet App
The Waylens Fleet App is the primary interface for the Secure4K, providing
the fleet an easy way to install and maintain
the camera.
Access the Secure4K through the App:
Installation Guide of Secure4K
Preview the video of Secure4K
Network Test
Power Cord Test
Secure4K Maintenance
Do not use mobile devices to access the Secure4K while operating the vehicle. Park your
vehicle in a safe location before accessing the App .
34
Logo LED
Waylens Button Function
The product contains a LTE Module
FCC ID: SRQ-ME3630

Installing your Secure4K
(two options - Direct Wire or OBD-II Power Cord)
1. Locate the OBD-II socket in your vehicle, the upper figure shows some popular places.
2. Insert the OBD-II plug into the OBD-II socket firmly.
NOTE: The OBD-II connector fits only one way into the vehicle’s OBD-II socket, do not force the fit; observe
correct orientation before applying force.
3. Route the wire with USB Type-C plug of the OBD-II Power Cord to the expected camera
mounting location on the windshield.
NOTE: Leave an extra few inches of cord length near the camera to insert the Type-C plug into the Secure4K
Dock, and also to make mounting and dismounting the camera easier.
4. Secure any excess wire after the camera is mounted.
Park the car in a safe and convenient place for the installation
The OBD-II socket
Option A OBD-II Power Cord
Option B Direct Wire Power Cord
1. Install power in the vehicle
1. Turn off the engine and the accessory power.
2. Find the location and layout of your fuse box as well as the appropriate fuse type from the
vehicle’s user manual.
NOTE:
a. Professional installation assistance at a qualified dealer is recommended, if you are not familiar with
identifying fuses in a vehicle and installing power system related items.
b. Please contact [email protected]om for assistance with finding an approved dealer in your area if
you are unsure of where to locate one yourself.
3. Connect the red ACC wire to a switched fuse:
a. A switched fuse is used to monitor the accessory power such as
cigarette lighter, car radio, etc. They will be switched off after you
turn off the car. Identify them by referring to the vehicle user manual
or consulting a qualified professional.
b. Verify the fuse is a switched fuse by using a multimeter to track
voltage within the circuit across ignitions ON and OFF positions.
c. If confirmed as a switched power fuse, remove the identified
switched fuse from the fuse panel. Use the fuse puller tool if available.
d. Remove the sleeve from the end of the red ACC wire, and wrap the
wire around one of the blades of the switched fuse.
e. Reinsert the fuse back into the fuse panel carefully and firmly to ensure the wire remains
secured to the fuse blade.
4. Connect the yellow BATT+ wire to a constant power fuse
a. The constant power fuses are used to monitor constant power within a vehicle. They will
not be switched off after you turn off the car. Identify them by referring to the vehicle manual
or consulting a professional.
5 6

b. Verify the fuse is a constant fuse by a multimeter to track voltage within the circuit across
ignitions ON and OFF positions.
c. If confirmed as a constant power fuse, remove the identified constant fuse from the fuse panel.
Use the fuse puller tool if available.
d. Remove the sleeve from the end of the yellow BATT+ wire and wrap the wire around one of the
blades of the Constant Power fuse.
e. Reinsert the fuse back into the fuse panel carefully and firmly to ensure the wire remains
secured to the fuse blade.
5. Connect the black GND wire to a chassis ground point, such as a bolt, that is directly touching
a bare metal surface of the vehicle’s framework.
6. Route the wire with USB Type-C plug of the Direct Wire Power Cord to the expected camera
mounting location on the windshield.
NOTE: Leave an extra few inches of cord length near the camera to insert the Type-C plug into the Secure4K
Dock, and also to make mounting and dismounting the camera easier.
7. Secure any excess wire after the camera is mounted.
1. Put the Type-C Power Cord into the Power Cord
Locker. Remove the Locker’s gasket if necessary.
2. Remove the Locker’s tape paper.
3. Insert the Type-C plug into the camera Type-C
socket. Push the Locker to ensure glued together
with the camera dock.
4. Seal with Tamp Tape.
5. Turn on the engine, the status LED will illuminate
blue and then turn red if a SD card is inserted.
For optimal performance, please ensure the power cord is firmly and securely fitted into the USB
Type-C Power Connection.
1. Open the Waylens Fleet App and follow the prompts to connect to the Secure4K camera.
2. If can’t find the Secure4K WiFi network, normally is a network with name as Waylens-xxxxx
(DIRECT-Waylens-xxxxx if WiFi Direct is enabled), press Waylens Button to wake up the WiFi.
3. Locate the diagnostic feature in the profile page(Skip Login) or Maintenance(Maintainer Login).
4. After the diagnostic, view the live preview of the camera to assist the placement on the
windshield.
Waylens Fleet App has the diagnostic feature to ensure the power cord connection is right.
3. Diagnostic with Waylens Fleet App
2. Connect power to the Secure4K Dock
7 8

4. Install the Mount Plate on the Windshield 5. Attach the Camera and Dock to the Mount Plate
SAFETY WARNING: Do not place the Secure4K in an area on the windshield where the product
interferes with the driver’s field of vision or other in-vehicle sensors. The Secure4K should be
mounted at the center top of the front windshield, optimizing visibility inside and outside the
vehicle.
NOTE: Do not place camera mount too low on windshield where visibility may be blocked by the vehicle itself,
such as wiper blades or raised hood structures.
1. Without removing the Mount Plate
adhesive cover plastic, position the
Mount with Placement Guide against
the top center of your windshield and
dashboard.
3. Firmly press the Mount Plate to the
windshield glass and hold for 10 seconds.
4. Remove the Placement Guide, leaving
the Mount Plate affixed to the windshield.
2. Verify placement on windshield, then
fold placement guide back away from
glass to remove the plastic cover for the
adhesive
Please be aware that certain films on the windshield glass can affect the night vision quality.
Please ensure the Secure4K is installed properly and firmly attached to the windshield prior to
operating the vehicle. Be sure to make any adjustments to the angle or position of the
Secure4K prior to operating the vehicle.
1. With the Mount Plate attached to the
windshield and the power cord connect-
ed to the Secure4K, position the
Secure4K on the left side of the Mount
Plate. Next, ensure the Mount Plate
locking tabs are aligned with their fittings
on the camera Dock.
2. Slide the camera right to secure it
firmly onto the Mount Plate.
9 10

6. Adjust Secure4K angle 7. Install and Calibrate the DMS camera
2. For optimal vision in and around your
vehicle, adjust the cameras position to
parallel with the road.
1. Use a coin to loosen the Dock hinge by
turning the adjustment slot
counter-clockwise.
3. Tighten the Dock into place by turning
the adjustment slot clockwise with a
coin.
11 12
DMS camera calibration process is to calibrate the DMS camera so that the DMS camera can detect
the driver's face and sight line so that the DMS camera can better detect and upload DMS events.
To calibrate the DMS camera, Waylens Fleet App should be used.
1. Install the DMS camera in the recommended
position as the picture shows.
2. Make sure that the DMS camera is upright.
1
2 3
3. Input the information of the vehicle where the
camera was installed.

8. Insert and format the microSD card
To prolong the usage, the new microSD card will be automatically formatted when the first time it
was inserted to Secure4K.
Do not remove the microSD card while the Secure4K is recording (the status LED illuninates red).
13 14
To install DMS module, first loose the Camera
Mount Screw, make the Remote Camera Cable
Socket appear.
Insert the DMS cable plug into the Socket, ensure
the direction is right.
Put the cable into the Cable Holder to release the
stress to the Cable socket/plug.
4/5
4 Adjust the camera position. There is a mask on
the view of the DMS camera. The installer should
keep adjusting the camera position to make the
driver image fit in the mask. When the mask turned
into green, the position of the DMS camera can be
regarded as correct.
5 Let the driver maintain the driving position and
look forward, tap "Calib and Look Forward". Wait
for 3 seconds until "Calibration is done" is heard
from the camera.
6. Install and calibrate the DMS module
Waylens recommends using a high endurance microSD card (class 10 or higher MLC microSD card
32-256GB) designed for continuous recording situations. While other cards will work with the
Secure4K, they are much more prone to card errors and failures.
Some Secure4K dock has a SD card cover to prevent the unauthorized access to the microSD card.
In that case please first loose the screw and the camera body.
You’re all set!

Removing the Secure4K Secure4K SIM Card
1. Stop the Secure4K if it’s recording by pressing the Waylens Button on the Dock or turning
monitoring off by fleet managers via API.
2. Slide the Secure4K Dock to the left and carefully pull the camera away from the Mount Plate
once you feel it release from the locking tabs.
Secure4K has pre-installed SIM card. Please do not remove the pre-installed SIM card.
3. Remove the power connection from the rear of the camera.
15 16
If finding that the SIM card is not activated, please contact the fleet manager to activate
the SIM card.

Making Intelligent Video Security
Easy for Fleets
FCC Caution: Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This transmitter must not operate in conjunction with any other antenna or
transmitter.
waylens.com
[email protected] 4K