Weed Eater 530163993 User manual

2500 Series
2600 Series
RTrademark
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
ENGLISH ESPAÑOL FRANÇAIS
530163993 1/23/04
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
FOR HOUSEHOLD USE ONLY
PARA USO CASERO SOLAMENTE
POUR UTILISATION À DES FINS
DOMESTIQUES SEULEMENT
Electrolux Home Products, Inc.
104 Warren Road
Augusta, GA 30907
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
Copyright E2004 Electrolux Home Products, Inc.

2
SAFETY RULES
IMPORTANT WARNINGS AND
SAFETY INSTRUCTIONS
WARNING:
When using electric gardening appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and serious injury. The warnings and
safety instructions in this manual must be followed to reduce the risk of fire, electric
shock, or injury, and to provide reasonable safety and efficiency in using this unit. The
operatoris responsible forfollowing the warningsand instructions in this manual andon
the unit. Read theentire instruction manual beforeassembling and using the unit! Re-
strict the use of this unit topersons whoread,understand,and follow the warningsand
instructions in this manual and on the unit. Never allow children to use this unit. Close
attention is necessary when used near children.
OPERATOR SAFETY
DAlways wearsafetyglassesor similareye
protection when operating, servicing, or
performing maintenance on your unit.
Wearing eye protection can help to pre-
vent rocks or debris from being blown or
ricocheting into eyes and face which can
result in blindness or serious injury.
DAlways wear a respirator or face mask
when working with the unit in dusty envi-
ronments.
DDress safely in long pants. Do not go
barefoot or wear short pants or sandals.
DDo not operate the unit when you are
tired,ill,upset,orifyouareundertheinflu-
ence of alcohol, drugs, or medication.
DSecurehairsoitisaboveshoulderlength.
Keep loose hair, loose clothing, fingers,
and all other parts of the body away from
openings and moving parts. Hair,jewelry,
loose clothing, or clothing with loosely
hanging straps, ties, tassels, etc., can be
caught in moving parts.
ELECTRICALSAFETY
WARNING: Avoida dangerous en-
vironment. To reduce the risk of electrical
shock, do not use in rain, in damp or wet
locations, or around swimming pools, hot
tubs, etc. Do not expose to snow, rain, or
water to avoid the possibility of electrical
shock. Do not handle extension cord plug
or unit with wet hands.
DUse only a voltage supply as shown on the
nameplate of the unit.
DAvoiddangeroussituations.Donot use in
presenceofflammableliquids orgases to
avoid creating a fire or explosion and/or
causing damage to unit.
DAvoid dangerous environments. Do not
useinunventilatedareasorwheredustor
explosive vapors can build up.
DTo reduce therisk of electrical shock, use
extension cords specifically marked as
suitable for outdoor appliances. The
electrical rating ofthe cord must be higher
than the rating of the unit. The cord must
be marked with the suffix “W-A” (inCana-
da, “W”). Make sure your extension cord
is in good condition. Inspect extension
cord before use and replace if damaged.
An undersized extension cord will cause
a drop in line voltage resulting in loss of
power and overheating. If in doubt, use
the next heavier gauge. The smaller the
gauge number, the heavier the cord.
(NOTE: The correct size to be used de-
pending on the cord length is shown in
this manual).
DInspect the insulation and connectors on
the unit and extension cord before each
use. If there is any damage, do not use
until damage is repaired by your autho-
rized service dealer. Do not pull or carry
by cord; do not use cord as a handle,
close a door on cord, or pull cord around
sharp edges or corners. Keep cord away
from heated surfaces. Do not unplug by
pullingoncord.Tounplug,grasptheplug,
not the cord.
DTie cord to cord retainer and connect to
recessed plug as shown in this manual to
prevent damage to unit and/or extension
cord and to reduce the possibility of the
extension cord disconnecting from the
unit during operation.
DDon’t use the unit if the switch does not
turn the unit onand off properly. Havethe
unit repaired by an authorized service
dealer.
DKeep extension cord clear of operator
and obstacles at all times. Do notexpose
cords to heat, oil, water, or sharp edges.
DAvoid any body contact with any
grounded conductor, such as metal

3
fences, or pipes, to avoid the possibility of
electric shock. Don’t handle plug or unit
with wet hands.
DDo not use with damaged cord or plug. If
unit is not working as it should, has been
dropped, damaged, left outdoors, or
dropped into water, return it to an autho-
rized service dealer for repair.
DGround Fault Circuit Interrupter (GFCI)
protection should be provided on the cir-
cuit or outlet to be used for this unit. Re-
ceptacles are available having built-in
GFCIprotection and may be used for this
measure of safety.
DKeep others including children, animals,
bystanders, andhelpers a minimum of 30
feet (10 meters) away. Stop the motor im-
mediately if you are approached. Do not
allow the unit to be used as a toy.
DOUBLE INSULATION CONSTRUC-
TION
Your unit is double insulated to help pro-
tectagainstelectricshock.Doubleinsula-
tion construction consists oftwoseparate
“layers” of electrical insulation instead of
grounding. Tools and appliances built
withadouble insulation systemarenotin-
tended to be grounded. No grounding
meansis providedonthis unit,norshould
a means for grounding be added to this
unit. As a result, the extension cord used
with your unit can be plugged into any
standard 120 volt electrical outlet.
Safetyprecautionsmustbeobservedwhen
operating any electrical tool.The double in-
sulation system only provides added pro-
tectionagainstinjuryresultingfromaninter-
nal electrical insulation failure.
WARNING: Allelectricalrepairsto
thisunit,including housing,switch,motor,
etc., must be diagnosed and repaired by
an authorized service dealer. Replace-
ment parts for a double insulated
appliance must be identical to the parts
they replace. A double insulated
appliance is marked with the words
“DOUBLE INSULATION” or “DOUBLE INSU-
LATED.” The symbol (square within a
square) mayalsobe markedontheap-
pliance. Failure to have the unit repaired
by an authorized service dealer can
cause the double insulation construction
to become ineffective and result in seri-
ous injury.
UNIT/MAINTENANCESAFETY
DTurnoff all controlsandallowthemotorto
stop before disconnecting the unit from
the power source.
DDisconnect the unit from the power
source when not in use. Do not leave the
unit when it is plugged into an outlet.
DDo not set the unit on any surfaceexcept
a clean, hard area while the unit is run-
ning. Debris such as gravel, sand, dust,
grass, etc., could be picked up by the air
intake and thrown out through the dis-
charge opening, damaging the unit, prop-
erty, or causing serious injury to bystand-
ers or operator.
DDo not overreach or use from unstable
surfaces such as ladders, trees, steep
slopes, rooftops, etc. Use extra care
when cleaning on stairways. Keep firm
footing and balance at all times. Keeps
hands out of tubes.
DInspect the entire unit before each use for
worn, loose, missing, or damaged parts.
Do not use until the unit is in proper work-
ing order.
DDisconnect unit from power source be-
fore servicing, cleaning, performingmain-
tenance, or storing.
DThis unit is double insulated. See the
DOUBLE INSULATION CONSTRUCTION
section. Have all internal service per-
formedby qualified service repair person-
nel to avoid creating a hazard or voiding
your warranty.
DHave all maintenance other than the rec-
ommended procedures described in the
instruction manual performed by an au-
thorized service dealer.
DAlways see an authorized service dealer
to replace a damaged impeller. Partsthat
are chipped, cracked, broken, or dam-
aged in any other way can fly apart and
cause serious injury. Replace damaged
parts before using the unit.
DNever place any object in the air intake
opening as this could restrict proper air
flow and cause damage to the unit.
DNever douse the unit with water or other
liquids or squirt with a water hose. Clean
with a damp sponge and mild soap. See
STORAGE.
DCheck air intake openings and tubes fre-
quently, always with the unit stopped and
power source disconnected. Keep vents
and tubes free from debris which can ac-
cumulate and restrict proper air flow.
DDo not burn,incinerate, or expose this
unit to extreme heat.
DStore the unit unplugged in a high, cool,
dry, indoor area out of the reach of chil-
dren.
DUse only recommended attachments
and replacementparts to avoid creatinga
hazard and/or voiding your warranty.
DMaintain the unit according to recom-
mended procedures.
DUse only for jobs explained in this man-
ual.

4
BLOWER SAFETY
DUse only in daylight or in good artificial
light.
DInspect the area before using the unit.
Remove all debris and hard objects such
as rocks, glass, wire, etc., that can rico-
chet, bethrown, orotherwise cause injury
or damage during operation.
DAvoid accidental starting. Be sure the
switch is in the OFF position and keep
your hand and fingers away from the
switch while connecting the unit to the
power source or when carrying a unit
connected to the power source.
DNever run the unit without the proper
equipment attached. When used as a
blower, always install a blower tube. Use
only recommended attachments. Do not
use with any opening blocked, Keep free
from dust, lint, hair and anything that may
reduce air flow.
DToavoid spreadingfire,do not useblower
near leaf or brush fires, fireplaces, barbe-
cue pits, ashtrays, etc.
DNever place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and
solid objects such as trees, automobiles,
walls,etc.Theforceofaircancause
rocks,dirt,orstickstobethrownortorico-
chet which can hurt people or animals,
break glass, or cause other damage.
DNever use for spreading chemicals,fertil-
izers, orany other substances which may
contain toxic materials.
VACUUM SAFETY (If applicable)
DStop the motor and disconnect the power
source before opening the airinlet door or
attempting to insert or remove the vacu-
um tubes. The motor must be stopped
and the impeller blades no longer turning
to avoid serious injury from the rotating
blades.
DHard objects can be thrown through the
collection bag or the housing and be-
come dangerous missiles which can
cause serious injury tooperatoror others.
DWhen using the vacuum attachment, the
unit is designed to pick up dry material
such as leaves, grass, small twigs, and
bits of paper. Do not vacuum stones,
gravel, metal, broken glass, etc., to avoid
severe damage to the impeller. To avoid
the possibility of electrical shock, do not
attempt to vacuum water or other liquids.
DNever run the unit without the proper
equipment attached. When used as a
vacuum, always install vacuum tubes
and collection bag assembly. Make
sure the collection bag assembly is
completely zipped when unit is running
to avoid flying debris. Use only recom-
mended attachments.
DAvoid situations which could set the col-
lection bag on fire. Do not vacuum dis-
carded matches, cigars, cigarettes, or
ash from fireplaces, barbecue pits, brush
piles, etc. To avoid spreading fire, do not
use blower near leaf or brush fires, fire-
places, barbecue pits, ashtrays, etc.
DAlways use collection bag shoulder strap
when vacuuming to avoid loss of control.
DCheck air intake openings, elbow tube,
and vacuum tubes frequently, always
with the unit stopped and the power
source disconnected. Keep vents and
tubes free of debris which can accumu-
late and restrict proper air flow. Do not
use with any opening blocked. Keep free
ofdust, lint, hair and anything thatmay re-
duce air flow.
STANDARDS
This product is listed by Underwriter’s Lab-
oratories, Inc., in accordance with UL Stan-
dard 1017.
If situations occur which are not covered in
this manual, use careand good judgement.
If you need assistance, contact your autho-
rizedservicedealeror call 1-800-554-6723.
Failure to follow all Safety Rules and Pre-
cautions can result in serious injury.
SAVE THESE INSTRUCTIONS
ASSEMBLY
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover or attempting to in-
sert or remove the inlet restrictor, blower
tube, nozzle, or vacuum tubes. The motor
mustbestoppedandtheimpellerbladesno
longer turning to avoid serious injury from
the rotating blades.
WARNING: If you receive your
unit assembled, check each step to in-
sure your unit is properly assembled and
all fasteners are secure. Follow all safety
information in the manual and on unit.
SA standard screwdriver is required for
assembly.

5
BLOWER ASSEMBLY
NOTE: Assembly intructions for using
your unit as a vacuum follow this section.
ATTACHINGTHEBLOWERTUBEAND
NOZZLE
1. Insert the blower tube into the blower
outlet.
2. Twist the blower tube clockwise until it
is firmly seated in the blower outlet.
3. Twist the nozzle into the end of the
blower tube until it is firmly seated.
Make sure the nozzle points upward.
Blower Tube Nozzle
Blower outlet
For Model 2695 only, the blower exten-
sion tube and nozzle are combined into
one component.
Blower Tube/Nozzle
VACUUM ASSEMBLY
(Some models)
NOTE: Assembly instructions for using
your unit as a blower are explained in the
previous section.
If you have already assembled your unit
for use as a blower, remove the blower
tube and nozzle.
REMOVE THE INLET RESTRICTOR
An inlet restrictor is used when using your
unit as a blower. This restrictor is not used
during vacuum use and must be removed
during assembly for vacuum use.
NOTE:Be sure to keep the inlet restrictor
for using your unit as a blower.
1. Ensure unit is stopped and extension
cord is unplugged.
2. Open the inlet cover by inserting the
tip of a screwdriver into the latch area
on the vacuum inlet cover. Gently tilt
handle of screwdriver toward thefront
oftheunitwhilepulling uponthevacu-
um inlet cover with your other hand.
Impeller
Latch Area
Vacuum Inlet Cover
3. Turn the inlet restrictor counterclock-
wise and remove it from the unit. Do not
close the inlet door. You will next attach
the vacuum tubes.
Inlet
Restrictor
Vacuum
Inlet Cover
ATTACHING THE VACUUM TUBES
There are 2 vacuum tubes, an upper and
lowertube.Theuppertubeiscut straighton
both ends and attaches to the blower unit.
The lower tube attaches to the upper tube,
and has an angled end that you point to-
ward the ground during vacuum use.
1. Ensure unit is stopped and extension
cord is unplugged.
2. Locate the arrowson the upper vacu-
um tube and on the vacuum inlet area
of the unit.
Upper Vacuum Tube
3. While holding the inlet cover open,
align the arrows and insert the vacu-
um tube into the opening. Twist the
tube clockwise until it is seated. A se-
cond arrow on the vacuum tube will
align with the arrow on the unit once
the tube is twisted completely into
place.
Align arrows on tube and unit
4. Toattachthelowervacuumtubetothe
upper vacuum tube, first align the ar-
rowsonthetwotubes.Then,pressthe
two tubestogether until the lower tube
is securely seated in the upper tube
(about 3 inches).
Upper Tube
Lower Tube
ATTACH THE COLLECTION BAG
Slide the opening of the collection bag
over the blower outlet. Pull the velcro
strap tightly through the buckle and se-
cure to the velcro tabs.

6
NOTE: Make sure the velcro strap is lo-
cated on the blower outlet as shown be-
low. Also, make sure the zipper on the
bag is completely closed.
Velcro Strap
Collection
Bag Blower Outlet
ADJUSTING THE SHOULDER STRAP
ON THE COLLECTION BAG
1. Carefully loop the shoulder strap
through the buckle as shown in the il-
lustration below.
First In
Last In
2. Position the unit on your right-hand
side, blower outlet and bag pointing
towardthe rear. Hold the unit in anup-
right position with the lower vacuum
tube on the ground to support it.
3. Place the shoulder strap over your
head and onto your left shoulder.
4. Adjust the strap to allow a free flow of
air from the blower. If the collection
bag is kinked, the unit will not operate
properly.
NOTE: The strap is designed to position
the collection bag on your shoulder without
kinks. The strap is not intended to support
the weight of the unit.
Shoulder strap
on left shoulder
No kinks in bag
allows free air flow
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Stop unit and unplug the extension
cord.
2. Remove the vacuum tubes and
collection bag.
3. Install the inlet restrictor that was re-
moved when assembling for vacuum
use.
NOTE:Ifyouareunable tolocate theinlet
restrictor,theunit will stilloperate.Thisre-
strictor improves the blower function.
4. Close the inlet cover and make sureit
is latched closed.
5. Re-install the blower tubes. Refer to
the section ATTACHING THE BLOWER
TUBE AND NOZZLE for instructions on
how to attach these items.
SELECT AN EXTENSION CORD
Use only a 120 A.C. voltage supply as
shown on the nameplate of the unit.
STo reduce the risk of electrical shock, this
equipment has a polarized plug (one
blade is wider than the other) and will re-
quire the use of a polarized extension
cord. The appliance plug will fitinto a po-
larized extension cord only one way. If
the plug does not fit fully into the exten-
sion cord, reverse the plug. If the plug still
does not fit,obtain acorrectpolarized ex-
tension cord. A polarized extension cord
will require the use ofa polarized wall out-
let. This plug will fit into the polarized wall
outlet only oneway. If plug does not fitful-
ly into the wall outlet, reverse the plug. Ifit
still does not fit, contact a qualified electri-
cian to install the proper wall outlet. Do
not change the equipment plug, exten-
sion cord receptacle, or extension cord
plug in any way.
The extension cord used toreach thepow-
er source must be:
DSpecifically marked as suitable for out-
door use. The cord must be marked with
the suffix “W-A” (in Canada “W”).
DHeavy enough to carry full current from
the power source to the unit. Otherwise,
loss of power and overheating can occur
causing damage to unit. Refer to table for
minimum wire gauge recommendations.
The cord must be marked with the proper
wire gauge. (Appropriate extension cords
are available.) Do not use multiple cords.
DIn good condition. Cord insulation must
be intact with no cracks or deterioration.
Plug connectors must be undamaged.
DO NOT use multiple cords.
Volts
25 ft.
120 18
50 ft.
16
Amp Rating
120 16 1610
MINIMUM A.W.G. WIRE GAUGE
RECOMMENDATIONS
6
More
Than A.W.G. A.W.G.
10
12
Not More
Than

7
Volts
100 ft.
120 14
150 ft.
12
Amp Rating
120 14 1210
A.W.G. = American Wire Gauge
MINIMUM A.W.G. WIRE GAUGE
RECOMMENDATIONS
6
More
Than A.W.G. A.W.G.
10
12
Not More
Than
SECURE EXTENSION CORD TO UNIT
CAUTION: Failure to use cord retainer
could result in damage to the unit, exten-
sion cord, or both.
1. Loop extension cord through cord re-
tainer.
2. Insert cord receptacle through loop.
3. Hold the cord receptacle in one hand.
Use the other hand to gently pull on
the extension cord to remove slack.
NOTE: Only remove enough slack
fromthe extension cord tosecure it to
the cord retainer. Pulling too hard
could damage the extension cord.
4. Insert the cord receptacle into the re-
cessed plug.
MODELS 2510 & 2525
12
34
ALL OTHER MODELS
12
34
USING YOUR UNIT
WARNING: You MUST make sure
the tubes are secure before using the unit.
WARNING: Do not use the unit
without the tubes or collection bag prop-
erly attached toavoid flying debris and/or
impeller contact whichcan cause serious
injury. Alwaysweareyeprotectiontopre-
vent rocks or debris from being blown or
ricocheting into the eyes and face which
can result in blindness or serious injury.
OPERATING POSITION
Eye Protection
Blower
Eye Protection
Vacuum
USING YOUR UNIT AS A BLOWER
WARNING: Inspect the area be-
foreusingtheunit. Removeall debrisand
hard objects such as rocks, glass, wire,
etc.,thatcanricochet,bethrown,orother-
wise cause injury or damage during op-
eration.
Use your unit as a blower for:
DSweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
DBlowing grass clippings, straw, or leaves
into piles, or removing debris from cor-
ners, around joints, or between bricks.
Direct air flow by directing the blower tube/
nozzle down or to one side. Always work
away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and
moving outward. This will help prevent an
accumulation of debris which could fly into
your face.
Be careful when working near plants. The
force ofthe air could damage tender plants.
USING YOUR UNIT AS A VACUUM
WARNING: Donotvacuumstones,
gravel, metal, broken glass, etc., to avoid
severe damage to the impeller. To avoid
the possibility of electrical shock, do notat-
tempt to vacuum water or other liquids.
Use your unit as a vacuum to pick up dry
material such as leaves, grass, small
twigs, and bits of paper.
DForbestresultsduringvacuumuse,op-
erate your unit at high speed.

8
DMove slowly back and forth over the
material as you vacuum. Avoid forcing
the unit into a pile of debris as this can
clog the unit.
DKeep the vacuum tube about an inch
above the ground for best results.
WARNING: If the unit becomes
clogged, stop the unit and unplug the ex-
tension cord. Wait until the impeller has
completely stopped turning, then remove
the vacuum tubes. Carefully reach into
the vacuum opening and clear out the
clogged debris.
MAINTENANCE
WARNING: Disconnect power
source before performing maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
items that have been subjected to operator
abuse or negligence. To receive full value
from the warranty, the operator must main-
tain unit as instructed in this manual. Vari-
ous adjustments will need to be made peri-
odically to properly maintain your unit.
BEFORE EACH USE
CHECK FOR LOOSE FASTENERS
AND PARTS
SInlet Cover
SBlower Tube
SVacuum Tubes
SCollection Bag
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for
replacement of damaged or worn parts.
SON/OFF Switch -- Ensure switch functions
properly by moving the switch to the OFF
position. Make sure motor stops; then re-
start motor and continue.
SInlet Cover -- Discontinue use of unit if in-
let cover fails to latch properly or if it is
damaged in any way.
AFTER EACH USE
INSPECT AND CLEAN UNIT & LABELS
Stop unit and unplug extension cord.
SAfter each use, inspect complete unit for
loose or damaged parts. Clean the unit
using a damp cloth with a mild detergent.
SWipe off unit with a clean dry cloth.
CLEAN COLLECTION BAG
IMPORTANT: THE COLLECTION BAG
MUST BE PROPERLY EMPTIED.
DYou must properly empty and maintain
the collection bag to avoid deterioration
and obstruction of air flow.
DRemove the collection bag from the unit
and empty after each use. Do not store
bag without emptying the bag of all con-
tents (grass, leaves, etc.).
DWash the bag once a year. Remove the
bag from the blower and turn the bag in-
side out. Wash thebag with a waterhose.
Allow the bag to hang and dry completely
before you reuse the bag.
SERVICE
HOW TO REMOVE AN OBJECT
FROM THE AIR INTAKE
WARNING: Stop the unit and dis-
connect from the power source before
opening the inlet cover. The motor must
be stopped and the impeller blades no
longer turningto avoid serious injury from
the rotating blades.
SWhile holding the inlet cover open, re-
move the vacuum tubes. The inlet cov-
er must be held open through all re-
maining steps.
SCarefully reach into the vacuum open-
ing and clear out the air intake area.
Clear all debris from impeller.
SInspect the impeller for cracks. If
cracked or damaged, do not use the
unit. Have parts replaced by your au-
thorized service dealer. Do not attempt
to replace them yourself.
STORAGE
WARNING: Perform the following
steps after each use:
SStop unit and disconnect from the power
source.
SAllow motor to cool before storing or
transporting.
SStore unit with all guards in place. Posi-
tion unit so that any sharp object cannot
accidentally cause injury.
SStore unit unplugged, well out of the
reach of children.
SEASONALSTORAGE
Prepare unit for storage at the end ofthe
season or if itwill not be used for 30days
ormore.Ifyourblower is tobestored fora
period of time:
SStop unit and disconnect from the power
source.
SClean the entire unit before lengthy stor-
age.
SOpen inlet cover and clean any dirt,
grass, or debris that has collected. In-
spect the blower and all tubes. Close and
make sure the cover is latched.

9
SClean air vents and air inlet of debris.
SStore your unit and extension cord in a
well ventilated areaand covered,if pos-
sible,topreventdustanddirtaccumula-
tion. Do not cover with plastic. Plastic
cannot breathe and may cause con-
densation and eventual rust or corro-
sion.
SCheck entire unit for loose screws. Re-
place any damaged, worn, or broken
parts.
NEED ASSISTANCE?
Need Accessories or Assistance?
Call: 1-800-554-6723.
Need Service Parts?
Contact your dealer.
ACCESSORIESAVAILABLE
Safety Goggles Stock #952701506
TROUBLESHOOTINGTABLE
SYMPTOM CAUSE REMEDY
Unit fails to
operate. 1. Switch in the OFF position. 2. Extension cord discon--
nected.
3. Circuit breaker tripped, or
fuse blown.
4. Mechanical failure
1. Move switch to ON position.
2. Reconnect extension cord.
3. Reset circuit breaker or
fuse.
4. Contact your authorized
service dealer.
Unit
vibrates
abnormally.
1. Mechanical failure 1. Contact your authorized
service dealer.
Impeller will
not turn free-
ly.
1. Debris in air intake area.
2. Mechanical failure. 1. Clean unit. Remove any
debris.
2. Contact your authorized
service dealer.
WARNING: Alwaysstopunitanddisconnectfromthepowersourcebefore
performingalloftherecommendedremediesbelow exceptremediesthatre-
quire unit to be operating.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS,
INC., warrants to the original purchaser
that each new Weed Eater brand electric
orcordless product is freefromdefectsin
material and workmanshipand agrees to
repair or replace under this warrantyany
defective Weed Eater brand electric or
cordlessproductwithintwo(2)yearsfrom
the original date of purchase.
IfyourWeedEater brandelectric or cord-
less product should fail within the limited
warranty period, return it, complete, pre-
paid, with proofof purchase,to thedealer
from whom it was purchased for repair or
replacement at the option of ELECTRO-
LUX HOME PRODUCTS, INC.
This warranty is not transferable and
does notcover damageorliability caused
by improper handling, improper mainte-
nanceortheuseofaccessoriesand/orat-
tachmentsnot specifically recommended
by ELECTROLUX HOME PRODUCTS,
INC., for this tool. Additionally, this war-
ranty does not cover parts that will wear
and require replacementwith reasonable
use during the warrantyperiod. This war-
ranty does not cover predelivery setup or
normal adjustments explained in the in-
struction manual.
THIS WARRANTY GIVES YOU SPE-
CIFIC LEGAL RIGHTS, AND YOU MAY
HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMI-
TATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLU-
SION OR LIMITATIONS OF INCIDEN-
TAL OR CONSEQUENTIALDAMAGES,
SO THE ABOVE LIMITATIONS OR EX-
CLUSIONMAY NOT APPLY TO YOU.
The policy of ELECTROLUX HOME
PRODUCTS,INC.,is to continuously im-
prove its products. Therefore, ELEC-
TROLUX HOME PRODUCTS, INC., re-
serves the right to change, modify, or
discontinue models, designs, specifica-
tions, and accessories of all products at
any time without notice or obligation to
any purchaser.