Weed Eater WELRVBA30 User manual

03.04.11 CL/TH Printed in the U.S.A.
This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all
mechanical products, some adjustments or part replacement may be necessary during the life of your unit.
For Parts and service, contact our authorized distributor: call 1-800-849-1297
• For replacement parts, have available the following information:
a. Model Number/Manufacturer's I.D. Number
b. Description of part.
For Technical Assistance: call 1-800-829-5886
For a Parts Manual, go to our website: www.weedeater.com
NOTE: HOP provides parts and service through its authorized distributors and dealers; therefore,
all requests for parts and service should be directed to your local dealer(s). The philosophy
of HOP is to continually improve all of its products. If the operating characteristics or the
appearance of your product differs from those described in this Manual, please contact
your local dealer for updated information and assistance.
PARTS AND SERVICE
Owner's Manual
532 44 19-83 Rev. 4
30" RIDING MOWER
SIDE DISCHARGE
ELECTRIC START
IMPORTANT:
Read and follow all Safety
Rules and Instructions before
operating this equipment.
Catalog No.
WELRVBA30
Patents Pending
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The
use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.

40
1 532 44 18-21 DECAL, STEERING WHEEL
2 532 44 14-97 DECAL, V-BELT SCH 30"
3 532 42 51-12 DECAL, WARN. DEFLECT/CTFGR
4 532 44 07-80 DECAL, DECK/DEFLECTOR
5 532 40 88-06 DECAL, ENGINE
- - 532 44 19-83 MANUAL OWNER'S ENGLISH
- - 532 44 19-84 MANUAL OWNER'S SPANISH
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1
4
4
5
3
2
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
DECALS PRODUCT NUMBER 960 26 00-01
5
• Never fill containers inside a vehicle or
on a truck or trailer bed with plastic liner.
Always place containers on the ground
away from your vehicle when filling.
• Remove gas-powered equipment from the
truck or trailer and refuel it on the ground.
If this is not possible, then refuel such
equipment with a portable container, rather
than from a gasoline dispenser nozzle.
• Keep the nozzle in contact with the rim
of the fuel tank or container opening at
all times until fueling is complete. Do not
use a nozzle lock-open device.
• If fuel is spilled on clothing, change clothing
immediately.
• Never overfill fuel tank. Replace gas cap
and tighten securely.
GENERAL SERVICE
• Never operate machine in a closed area.
• Keep all nuts and bolts tight to be sure the
equipment is in safe working condition.
• Never tamper with safety devices. Check
their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel spill-
age and remove any fuel-soaked debris.
Allow machine to cool before storing.
• If you strike a foreign object, stop and
inspect the machine. Repair, if necessary,
before restarting.
• Never make any adjustments or repairs
with the engine running.
• Check grass catcher components and the
discharge chute frequently and replace
with manufacturer’s rec ommended parts,
when necessary.
• Mower blade is sharp. Wrap the blade or
wear gloves, and use extra caution when
servicing them.
• Check brake operation frequently. Adjust
and service as required.
• Maintain or replace safety and instruction
labels, as necessary.
• Be sure the area is clear of bystanders
before operating. Stop machine if anyone
enters the area.
• Never carry passengers.
• Do not mow in reverse unless absolutely
necessary. Always look down and behind
before and while backing.
SAFETY RULES

6
Steering Wheel
Insert
Steering Wheel
Steering
Boot
Seat
Steering
Shaft Cover
Steering Shaft
Extension (1) Large Flat
Washer
(1) Lockwasher
(1) 5/16-18 x 4
Hex Bolt
Slope Sheet
(2) Key
Steering Wheel
Adapter
PRODUCT SPECIFICATIONS
UNASSEMBLED PARTS
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintain-
ing, caring for and using your tractor.
• Follow the instructions under “Customer
Responsibilities” and “Storage” sections
of this owner’s manual.
WARNING: This riding mower is
equipped with an internal combustion en-
gine and should not be used on or near any
unimproved forest-covered, brush-covered
or grass-covered land unless the engine’s
exhaust system is equipped with a spark
arrester meeting applicable local or state
laws (if any). If a spark arrester is used, it
should be maintained in effective working
order by the operator.
A spark arrester for the muffler is available
through your nearest authorized service
center/department.
In the state of California the above is required
by law (Section 4442 of the California Public
Resources Code). Other states may have
similar laws. Federal laws apply on federal
lands.
PRODUCT SPECIFICATIONS
Gasoline Capacity 1.5 Quarts
and Type: Unleaded Regular
Oil Type SAE 30 (above 32°F)
(API-SG-SL): SAE 5W30 (below 32°F)
Oil Capacity: 48 oz.
Spark Plug: Champion RC12YC
(Gap: .030")
Ground Speed Forward: 0 - 4
(Mph): Reverse: 0 - 2
Charging System: 3 Amps Battery
5 Amps Headlights
Blade Bolt Torque: 45-55 Ft. Lbs.
39
1 532 43 68-48 DECK
2 532 19 28-70 MANDREL ASM
3 532 43 68-56 KEEPER, BELT
4 532 43 68-55 PULLEY, MANDREL
5 532 44 15-97 BELT
6 532 43 68-63 COVER, MANDREL
7 532 43 71-44 LIFT ASM, DECK
10 532 43 96-38 DEFLECTOR
12 532 43 66-47 PIN, HINGE
13 532 43 74-62 SPRING, TORSION
14 532 19 51-85 ARM, MOWER SUPPORT
17 819 19 19-12 WASHER
18 532 19 42-09 PIN
19 532 19 65-39 BOLT, SHOULDER
20 532 19 42-08 PIN COTTER 5/16 BOW TIE LOCK
22 532 44 15-98 LINK ASM DECK
25 532 12 47-88 RETAINER SPRING 1"
26 532 18 76-90 SPACER, MANDREL
27 532 17 39-84 BOLT, MANDREL
28 532 40 02-34 NUT FLANGE LOCK TOP
29 532 41 92-73 BLADE
30 532 19 30-03 BOLT, BLADE
31 532 19 31-97 PULLEY, IDLER
32 532 14 10-43 GUARD, IDLER TUV
34 872 11 06-12 BOLT, 3/8-16 X 1 1/2
35 532 19 94-70 ARM, BRAKE
36 532 13 77-29 SCREW THD ROLL 1/4-20 X 5/8
37 873 90 06-00 NUT, 3/8-16 FLANGE
40 819 17 16-16 WASHER, 16 GA.
48 532 43 68-57 ARM CLUTCHING
49 532 19 90-92 SPACER RETAINER
50 817 00 06-16 SCREW 3/8-16 X 1
52 817 60 04-06 SCREW 1/4-20 X 3/8
53 532 40 18-72 SPRING RETURN DECK
55 532 43 79-88 E-RING 5/16
56 532 43 68-62 ROD ANTI-SWAY
57 819 13 13-12 WASHER 13/32 X 13/16 X 12 GA
59 532 43 68-58 GUARD TUV IDLER
61 532 43 79-47 MULCH COVER ASM
62 532 17 62-05 TRUNION SUSPENSION ARM
63 532 17 59-94 NUT LIFT LINK 7/16-20
64 817 67 06-08 SCREW THDROL 3/8-16 X 1/2
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
MOWER DECK PRODUCT NUMBER 960 26 00-01

38
6
36
18
18
5
4
3
26
2
1
27
27
13
55
12
19
19
17
14
17
29
30
63
63 62
22
64
28
10
61
25
31 37
50
49
48
59
34
34
52
35
53
32
37
7
19
19
40
40
37
57
20
56
57
20
LRV-B_Deck_4_r1
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
MOWER DECK PRODUCT NUMBER 960 26 00-01
7
Your new riding mower has been assembled at the factory with the exception of those parts
left unassembled for shipping purposes. To ensure safe and proper operation of your riding
mower all parts and hardware you assemble must be tightened securely. Use the correct
tools as necessary to ensure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly
easier. Standard wrench sizes you need
are listed below.
(1) 1/2" wrench (1) Utility knife
(1) Tire pressure gauge
When right or left hand is mentioned in
this manual, it means when you are in the
operating position (seated behind the steer-
ing wheel).
TO REMOVE RIDING MOWER FROM
CARTON
UNPACK CARTON
1. Remove all accessible loose parts and
parts boxes from carton.
2. Cut along dotted lines on all four panels
of carton. Remove end panels and lay
side panels flat.
3. Remove packing materials from riding
mower.
4. Check for any additional loose parts or
cartons and remove.
NOTE: Only cut carton with a short blade
utility knife, a long blade or saw can puncture
tires on unit.
ASSEMBLY/PRE-OPERATION
TO INSTALL STEERING WHEEL
1. Slide extension shaft onto steering shaft.
2. Slide steering shaft protective foam cover
over steering shaft.
3. Place steering boot over steering shaft
and push down to secure.
4. Position front wheels of the riding mower
so they are pointing straight forward.
5. Remove steering wheel adapter from
steering wheel and slide adapter onto
steering shaft.
7. Press steering wheel into position on
shaft, install large washer, lock washer,
bolt and tighten securely.
8. Snap steering wheel insert into center of
steering wheel securely.
Foam Cover
Adapter
Steering Wheel
Insert
Washer
Lock Washer
Bolt
Steering Shaft
Steering Boot
Extension
Shaft

8
NOTE: You may now roll your riding
mower off the skid. Follow the appropriate
instruction below to remove the riding mower
from the skid.
WARNING: Before starting, read, un-
derstand and follow all instructions in the
Operation section of this manual. Be sure
riding mower is in a well-ventilated area.
Be sure the area in front of riding mower is
clear of other people and objects.
TO ROLL RIDING MOWER OFF
SKID (See Operation section for
location and function of controls)
1. Raise deck lift lever to its highest position.
2. Release parking brake by depressing
clutch/brake pedal.
3. Shift unit to neutral.
4. Roll riding mower forward off skid.
HOW TO SET UP YOUR RIDING
MOWER
CHECK BATTERY
Ensure battery is securely fastened, and that
all wires are securely connected.
• Battery is located under the seat.
• Battery has been fully charged from the
factory, before installation.
Seat Battery
Adjustment Lever
Lumbar
Adjustment Knob
TO ADJUST SEAT
FRONT AND BACK -
• Sit in seat.
• Lift up adjustment lever and slide seat
until a comfortable position is reached
which allows you to press clutch/brake
pedal all the way down.
• Release lever to lock seat in position.
INSTALL SEAT
1. Remove bolt and flat washer securing
seat to cardboard packing and set aside
for assembly of seat to riding mower.
Remove the cardboard packing and
discard.
2. Place seat on seat pan so all three (3)
bottom pads are positioned over large
slotted holes in pan.
3. Push down on seat to engage pads in
slots and pull seat towards rear of riding
mower.
4. Raise seat and tighten bolt and large flat
washer securely.
5. Remove tape and discard.
6. Lower seat into operating position and
sit on seat. Press clutch/brake pedal all
the way down. If operating position is not
comfortable, adjust seat.
Adjustment
handle
Bolt
Flat
washer
Seat
pan
Pad
Tape
Slot
Ta b
LUMBAR SUPPORT -
• Loosen lumbar adjustment knob.
• Slide seat back up or down to most com-
fortable position for lower back support.
• Tighten lumbar adjustment knob.
37
1 532 44 21-39 WHEEL TUBE
2 812 00 00-01 E-CLIP
3 532 18 89-67 WASHER, HARDENED
4 532 12 17-49 WASHER, 1/4 X 3/4
5 532 43 61-81 SPINDLE, RH
6 532 12 49-31 WASHER, HARDENED THRUST
7 532 12 49-37 BUSHING, STEERING COLUMN
9 819 13 14-14 WASHER
10 532 42 80-57 WELDMENT, LWR STRG SHAFT
11 532 44 21-39 LINK, STRNG LH
12 532 43 61-84 LINK, STRNG RH
13 874 78 05-24 BOLT, 5/16-18 X 1 1/2
14 819 11 12-16 WASHER 11/32 X 3/4 X 16 GA
15 873 80 05-00 NUT, 5/16-18
16 532 43 62-82 BUSHING SNAP
17 532 43 61-78 SUPPORT, UPPER STEERING
19 817 00 05-12 BOLT, 5/16-18 X 3/4
20 532 42 80-45 CLIP, RETAINER SPRING
23 532 43 77-47 ADAPTER, STEERING WHEEL
26 532 44 21-40 WHEEL, STEERING
27 532 44 21-41 CAP, STEERING WHEEL
28 532 19 98-49 CLIP, RETAINER SPRING
29 532 43 61-80 SPINDLE, LH
30 532 43 64-99 CAP, HUB, AXLE
31 819 34 32-10 WASHER 1-1/16 X 2 X 10GA.
32 817 58 05-20 SCREW HEXWSH THD 5/16-18 X 1-3/4
34 532 43 61-82 SHAFT STEERING UPPER
35 532 44 20-66 BOOT LOWER STEERING WHEEL
36 532 19 60-75 SHAFT EXTENSION STEERING SPLINE
37 874 78 05-80 BOLT FIN HEX 5/16-18 UNC X 5 GR5
38 810 04 05-00 WASHER LOCK HVY HLCL SPR 5/16
39 819 11 38-12 WASHER 11/32 ID X 2 3/8 OD X 12 GA.
41 532 43 65-90 FOAM SHAFT STEERING
42 532 42 10-76 PIN, 5/64 X 3/4 COTTER
43 873 54 05-00 CROWNLOCK NUT 5/16-24 UNF
44 532 42 80-44 BUSHING
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
STEERING PRODUCT NUMBER 960 26 00-01

36
41
16
27
37
38
39
26
23
36
35
34
17
19
19
15
13
9
11
20
10
2
6
7
7
29
6
2
6
7
7
6
5
1
3
2
30
28
4
42
1
3
2
30
43
14
14
32
43
44
31
12
38
38
4
LRV-B_Steering_3
32
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
STEERING PRODUCT NUMBER 960 26 00-01
9
CHECK TIRE PRESSURE
The tires on your riding mower were overin-
flated at the factory for shipping purposes.
Correct tire pressure is important for best
cutting performance.
CHECK DECK LEVELNESS
For best cutting results, mower housing
should be properly leveled. See “TO LEVEL
MOWER HOUSING” in the Service and
Adjustments section of this manual.
CHECK FOR PROPER POSITON OF
MOWER DRIVE BELT
See the figure that is shown for replacing the
mower drive belt in the service and adjust-
ment section of this manual. Verify that the
belt is routed correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your riding
mower, check to see that the brake is oper-
ating properly.
✓CHECKLIST
Before you operate your new riding mower,
we wish to assure that you receive the best
performance and satisfaction from this Qual-
ity Product.
Please review the following checklist:
✓ All assembly instructions have been
completed.
✓ No remaining loose parts in carton.
✓ Battery is properly connected.
✓ Seat is adjusted comfortably and tight-
ened securely.
✓ All tires are properly inflated. (For ship-
ping purposes, the tires were overinflated
at the factory).
✓ Be sure mower deck is properly leveled
side-to-side/front-to-rear for best cutting
results. (Tires must be properly inflated
for leveling).
✓ Check mower belt. Be sure it is routed
properly around pulleys and inside all belt
keepers.
✓ Check wiring. See that all connections
are still secure and wires are properly
clamped.
While learning how to use your riding mower,
pay extra attention to the following important
items:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular
unleaded gasoline.
✓ Become familiar with all controls, their
location and function. Operate them
before you start the engine.
✓ Be sure brake system is in safe operating
condition.
✓ Be sure Operator Presence System and
Reverse Operation System (ROS) are
working properly (See the Operation and
Maintenance sections in this manual).

10
OPERATION
These symbols may appear on your riding mower or in literature supplied with the product.
Learn and understand their meaning.
DANGER, KEEP HANDS
AND FEET AWAY
KEEP AREA CLEAR SLOPE HAZARDS
15
15
(SEE SAFETY RULES SECTION)
BATTERY REVERSE FORWARD
FAST SLOW
ENGINE ON
ENGINE OFF
OIL PRESSURE
FUEL
CHOKE
MOWER HEIGHT
PARKING BRAKE
LOCKED
PARKING BRAKE
UNLOCKED
REVERSE NEUTRAL HIGH LOW
ATTACHMENT
CLUTCH ENGAGED
PARKING BRAKE
ATTACHMENT
CLUTCH DISENGAGED
P
ENGINE START
MOWER LIFT
Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety inform-
ation about hazards which can
result in death, serious injury
and/or property damage.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.
HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
BRAKE/CLUTCH
PEDAL
REVERSE
OPERATION
SYSTEM (ROS)
IGNITION SWITCH
35
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 532 44 21-38 WHEEL ASM (REAR)
2 532 12 17-48 WASHER, 16 GA.
3 812 00 00-01 E-CLIP
6 532 15 69-72 SPACER AXLE
7 874 78 04-28 HCS 1/4-20 X 1-3/4 GR 5 ZD
8 532 44 18-51 WELMENT SUPPORT AXLE RH
9 532 44 19-36 SUBASM FINAL DRIVE
10 817 00 05-12 SCREW 5/16 - 18 X 3/4
11 532 43 67-41 BRACKET.SUPPORT.RH
12 532 43 61-48 CASE CHAIN RH
13 532 43 72-80 BEARING BALL 6207-SRS
14 532 43 71-76 SPROCKET DRIVEN 37 TOOTH
15 532 44 25-51 TUBE INPUT HEX
16 532 43 61-53 CHAIN PRIMARY DRIVE
17 532 43 72-82 BEARING BALL 6204-3-2RS
18 532 43 61-49 CASE CHAIN LH
19 818 05 10-10 SCREW 10 - 24 X 5/8 PAN HEAD
TORX
20 532 12 49-31 WASHER THRUST .75 X 1.230
22 532 43 66-96 WELMENT SUPPORT AXLE LH
23 818 10 10-08 SCREW TORX #10 - 14 X 1/2
32 532 43 61-51 BLOCK TENSION CHAIN
33 532 43 61-50 SPRING ADJUSTER TENSION
34 877 10 10-40 PIN CLEVIS 5/16 X 2-1/2
36 532 43 57-22 SHAFT INPUT CLUTCH
37 532 43 61-52 SPROCKETSPLINED14TOOTH
39 532 43 04-70 BEARING BALL
40 532 43 69-39 ARM BRAKE
41 532 10 95-53 SWITCH INTLK CL MWR GRY
4 TERM
43 873 80 05-00 NUT LOCK HEX W/INSERT
5/16 - 18 UNC
44 532 43 66-52 COVER END HEX
45 532 43 61-54 SPRING DRIVE
47 532 43 69-49 BRACKET MOUNT CABLE LRV
B
48 817 54 10-16 SCREW.HEX.HEAD WASH.10-
24X1.00
51 532 43 67-39 BRACKET SUPPORT LH
53 873 90 06-00 LOCK NUT, FLANGED
54 532 43 57-26 BEARING BALL
55 532 43 77-77 COVER WHEEL CLUTCH
57 532 43 65-59 WHEEL FRICTION
59 532 44 10-97 PLATE.CLUTCH.DRIVE
60 532 43 77-87 PLATE PRESSURE DRIVE
62 532 43 77-86 PLATE CLUTCH BRAKE
63 532 43 77-85 PLATE PRESSURE BRAKE
65 532 43 57-23 PLATE PRESSURE MASTER
66 532 43 57-24 BEARING THRUST 20MM
67 532 43 57-25 PLATE THROWOUT
68 532 43 57-28 BEARING BALL LOOSE
69 532 43 57-27 COVER CLUTCH
70 532 41 15-55 GRIP LEVER
71 532 43 68-65 TUBE SHIFT LRV
72 872 11 04-06 BOLT CARR.
73 873 68 04-00 NUTCROWNLOCK1/4- 20UNC
75 532 43 67-58 BRACKET MOUNT SHIFT
76 532 18 39-00 HUB SHIFT
78 532 42 90-55 SPACER NYLON .866 X 1.25 X
.250
79 874 78 04-12 BOLT.FIN.HEX.1/4-20 UNC X .75
80 810 04 04-00 WASHER LOCK HVY HLCL
SPRING
81 819 09 12-10 WASHER 9/32 X 3/4 X 10 GA.
84 819 11 16-10 WASHER 11/32 X 1.00 X 10 GA.
85 532 43 69-14 SPRING FRICTION PACK
86 532 43 73-04 BUSHING PACK FRICTION FD2
87 532 43 69-48 WASHER PLASTIC
88 532 43 67-01 STUD PACK FRICTION
89 532 43 72-99 SPACER PACK FRICTION FD2
90 819 11 14-16 WASHER.11/32 X 7/8 X 16 GA.
91 532 43 69-24 SUBASM.LINK.SHIFT
94 532 43 69-18 WELDMENT.SHIFT.FD2
95 532 43 68-66 PLATE.SHIFT
96 532 43 77-67 DRUM CLUTCH MULTI DISC
97 532 43 69-25 SUBASM LINK SHIFT PRIMARY
98 532 15 03-60 NUT LOCK CENTER 1/4 - 28
FNTHD
101 817 06 06-24 SCREW.3/8-16X1-1/2. SMGML.
TAP/R
102 532 08 67-77 THREAD.CUTTER
103 532 10 98-69 SWITCH.SEAT.
104 532 43 77-81 HUB CENTER
105 532 43 61-42 SPRING WAVE C125-H5
106 532 19 43-21 SPACER RETAINER
107 532 12 47-88 PIN COTTER
108 532 43 67-84 BUSHING.5/16IDX7/16ODX1/2
109 532 43 64-99 CAP.HUB.AXLE.1.50 X 1.00.
MS613
110 532 42 84-61 BRACKET SHIFTER FLEX
111 532 12 35-83 KEY.SQUARE.2.0 X .1845/.1865
112 818 10 10-12 SCREW TORX #10-14 X .750
113 873 90 05-00 NUT LOCK HEX FLANGE 5/16-
18
114 532 43 62-82 FLANGED BEARING
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
DRIVE PRODUCT NUMBER 960 26 00-01

34
10
10
11
109
2
3
1
2
2
6
7
7
9
8
12
13 14
15 16
13 18
19
19
19
19
19
19
20 17
23
23
1
2
3109
262
32 33
34
54 36
37 54
39 40
41
39 43 112
112
112
45
47 48
48
53 54 55
54 57
23
23
23
59 60
59 62
63
62
65
66 67
68
68
69
70
71
72
73
73 75
76
72 78
79
80 81
43 84
85 86
87
88
89
113
91
98
94
95
97
98
98
101 102
103
44
96
114
114
104
105
106
98
110
90
108 90
107
22
51 10
111
10 111
LRV-B_Drive_1_r2
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
DRIVE PRODUCT NUMBER 960 26 00-01
11
KNOW YOUR RIDING MOWER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING
YOUR RIDING MOWER
Compare the illustrations with your riding mower to familiarize yourself with the locations
of various controls and adjustments. Save this manual for future reference.
Our riding mowers conform to the applicable safety standards of the
American National Standards Institute.
DECK CLUTCH LEVER - Used to engage
the mower blade.
BRAKE PEDAL - Used for braking the riding
mower and starting the engine.
HEIGHT ADJUSTMENT LEVER - Used to
adjust mower cutting height.
IGNITION SWITCH - Used for starting and
stopping the engine.
LIFT LEVER PLUNGER - Used to release
height adjustment lever when changing its
position.
PARKING BRAKE LEVER - Locks parking
brake into brake position.
MOTION CONTROL LEVER - Selects the
speed and direction of the riding mower.
ROS “ON” POSITION - Allows operation of
mower deck or other powered attachment
while in reverse.
THROTTLE/CHOKE CONTROL – Used for
starting and controlling engine speed.
Ignition
Switch
ROS
"ON"
Motion Control
Lever
Throttle/Choke
Control
Lift Lever
Plunger
Height
Adjustment
Lever
Deck Clutch
Lever
Brake Pedal
Parking
Brake Lever

12
The operation of any riding mower can result in foreign objects thrown
into the eyes, which can result in severe eye damage. Always wear
safety glasses or eye shields while operating your riding mower or
performing any adjustments or repairs. We recommend a wide vision
safety mask over spectacles or standard safety glasses.
00155
HOW TO USE YOUR RIDING
MOWER
TO SET PARKING BRAKE
Your riding mower is equipped with an opera-
tor presence sensing switch. When engine
is running, any attempt by the operator to
leave the seat without first setting the parking
brake will shut off the engine.
1. Depress brake pedal all the way down
and hold.
2. Pull parking brake lever up and hold,
release pressure from brake pedal, then
release parking brake lever. Pedal should
remain in brake position. Ensure parking
brake will hold mower secure.
STOPPING
MOWER BLADE -
• To stop mower blade, move deck clutch
lever to disengaged position.
GROUND DRIVE -
• To stop ground drive, depress brake pedal
all the way down.
• Move motion control lever to neutral posi-
tion.
() Deck Clutch
Control
“Disengaged”
( ) Deck Clutch
Control
“Engaged”
ENGINE -
• Move throttle control between half and full
speed (fast) position.
NOTE: Failure to move throttle control be-
tween half and full speed (fast) position, be-
fore stopping, may cause engine to “backfire”.
• Turn ignition key to “STOP” position and
remove key. Always remove key when
leaving riding mower to prevent unauthor-
ized use.
IMPORTANT: Leaving the ignition switch in
any position other than "STOP" will cause
the battery to discharge and go dead.
NOTE: Under certain conditions when riding
mower is standing idle with the engine run-
ning, hot engine exhaust gases may cause
“browning” of grass. To eliminate this pos-
sibility, always stop engine when stopping
riding mower on grass areas.
CAUTION: Always stop riding mower
completely, as described above, before
leaving the operator's position.
Throttle
Motion Control Lever
33
1 532 43 61-76 WELDMENT, CHASSIS
2 532 18 01-66 BRACKET, SEAT
7 532 43 61-77 PLATE, ENGINE
8 532 43 68-60 BRACKET, CHASSIS FRONT
10 532 44 18-05 PAN, SEAT
11 532 19 93-70 BRACKET,SWITCHMOUNTING
13 532 43 65-95 COVER, FOOT REST
14 532 43 65-92 STRUCTURE, FOOT REST
15 532 44 20-69 SUPPORT, FOOT REST
16 532 43 93-94 PANEL ASM, CONTROL
18 532 43 92-73 ENGINE, (NON-CALIFORNIA)
215807-1529-G1
19 532 43 68-61 KEEPER, BELT
22 532 44 21-30 DECK CLUTCH ASM
23 532 14 98-46 KNOB
25 872 14 04-24 BOLT
26 873 51 04-00 NUT, 1/4-20
29 532 43 89-21 BOLT, 7/16-20 X 1.00
32 817 06 06-20 SCREW 3/8-16 X 1-1/4
33 532 12 41-81 SPRING, SEAT
34 532 12 37-40 SPRING
35 872 05 04-12 BOLT, 1/4-20 X 1 1/2
39 532 13 43-00 SPACER
40 532 12 12-48 BUSHING, NYLON SNAP
41 532 12 39-76 NUT, LOCK
42 532 17 18-52 BOLT, 5/16-18 SHOULDER
43 873 80 05-00 NUT, 5/16-18
44 532 43 66-12 SEAT
45 817 00 05-12 BOLT, 5/16-18 X 3/4
51 532 42 88-56 BRACKET
52 532 14 50-06 CLIP PUSH-IN HINGED
53 532 43 85-62 SCREW
54 532 43 64-73 DISC FRICTION
55 532 43 58-08 TORSION BODY UPPER
56 532 44 19-25 TORQUE ASM CONTROL
LOWER
57 532 43 64-79 SPRING HELIX
59 819 18 24-11 WASHER 9/16ID X1 1/2OD 11G
ZIN
60 532 43 78-56 FUEL TANK ASM
62 532 40 04-14 FUEL LINE
63 532 41 41-19 PURGE LINE
64 532 12 34-87 CLAMP HOSE
65 532 43 85-96 FUEL CAP
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
66 532 43 66-06 FUEL TANK SUPPORT BRKT
67 532 42 17-56 SCREW #10 X 0.500
68 532 43 98-51 SHIELD HEAT
69 532 43 74-27 BRACKET MOUNT CABLE
70 532 44 20-68 CONSOLE CENTER
CUPHOLDER
71 532 43 78-57 THROTTLE ASM
72 532 19 51-61 STUD FASTNER
73 873 90 05-00 NUT LOCK HEX FLANGE 5/16-
18
76 877 10 08-12 PIN CLEVIS
77 876 02 02-08 PIN COTTER 1/16 X 1/2
78 532 43 70-56 BRACKET SUPPORT ROD
79 532 43 70-57 BRAKE WELDMENT
80 532 42 96-93 BRAKE PEDAL COVER
81 532 43 73-74 WELDMENTLINKCONNECTING
82 532 16 94-84 RETAINER CLIP
83 532 43 93-68 STEERING BOOT REAR
84 532 43 92-91 STEERING BOOT FRONT
85 532 43 76-60 PARKING BRAKE HANDLE
86 532 43 87-62 ACTUATOR PARKING BRAKE
87 532 16 54-92 SHOULDER BOLT
88 532 42 81-10 CROSS BRACE
91 532 43 74-01 TRACK CLUTCH BRKT
94 874 49 05-48 BOLT
95 532 43 67-02 BRACKET
97 532 43 64-72 PULLEY ENGINE
98 817 49 04-08 SCREW 1/4-20 X 1/2
104 818 10 10-08 SCREW #10-14 X 1/2
105 532 44 21-34 ENGINE COVER
106 532 43 68-34 STRAP BATTERY
108 532 43 71-68 COVER REAR TRANSAXLE
109 532 43 90-08 RETAINER BRAKE
110 532 42 21-45 CONTROL HINGE PIN
111 532 43 81-71 SHIELD, BRAKE CABLE
112 817 72 04-08 SCREW THD CUT
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
CHASSIS PRODUCT NUMBER 960 26 00-01

32
74
73
57
105
18
97
26
5353
55
56
59
29
54
53
53
45
32
32
45
45
45
112
111
112
7
70
23
22
67
67
88
108
15
77 76
45
45
14
72
72
94
73
45
45
51
45
825
45
78
82
81
87
19
1
80
79
45
45
104
91 95
13
84
85
83
82
86
71
16
60
65
110
110
66
62
63
64
64
68
67
45
67
67
109
67
45
45
69
LRV-B_Chassis_10
33
44
10
101
100
42
52
52
42
43
35
39
39
40
41
34
103
102
11
106
40
41
34
2
45
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
CHASSIS PRODUCT NUMBER 960 26 00-01
13
Motion Control Lever
TO MOVE FORWARD AND BACKWARD
The direction and speed of movement is
controlled by the motion control lever.
1. Ensure the parking brake is applied.
2. Start riding mower with motion control
lever in neutral (N) position.
3. Release parking brake.
4. Slowly move motion control lever to
desired position.
TO ADJUST MOWER CUTTING HEIGHT
The position of the mower height deck lift
lever determines the cutting height.
• Grasp lift lever.
• Press lift lever plunger with thumb and
move lever to desired position.
The cutting height range is approximately
1-1/2 to 4". The heights are measured from
the ground to the blade tip with the engine
not running. These heights are approximate
and may vary depending upon soil condi-
tions, height of grass and types of grass
being mowed.
TO OPERATE MOWER
Your riding mower is equipped with an
operator presence sensing switch. Any
attempt by the operator to leave the seat
with the engine running and the deck clutch
engaged will shut off the engine. You must
remain fully and centrally positioned in the
seat to prevent the engine from hesitating or
cutting off when operating your equipment
on rough, rolling terrain or hills.
1. Select desired height of cut.
2. Start mower blade by engaging deck
clutch lever.
TO STOP MOWER BLADE -
Disengage deck clutch lever.
Mower Height
Adjustment High
Position
Mower
Height Adjustment
Low Position
Deck Clutch Lever
"Disengaged" Position
Deck Clutch Lever
"Engaged" Position
TO USE THROTTLE CONTROL
Always operate engine at full speed (fast).
• Operating engine at less than full speed
(fast)reducesengine'soperatingefficiency.
• Full speed (fast) offers the best mower
performance.
Throttle
• The average lawn should be cut to ap-
proximately 2-1/2" during the cool season
and to over 3" during hot months. For
healthier and better looking lawns, mow
often and after moderate growth.
• For best cutting performance, grass over
6" in height should be mowed twice. Make
the first cut relatively high; the second to
desired height.
CAUTION: Do not operate the mower
without either the entire grass catcher, on
mowers so equipped, mulch cover, or the
deflector shield in place.
Mulch CoverDeflector Shield

14
TO ATTACH DEFLECTOR
1. Unhook the 2 bungees from deck to the
mulch cover.
REVERSE OPERATION SYSTEM (ROS)
Your riding mower is equipped with a Reverse
Operation System (ROS). Any attempt by
the operator to travel in the reverse direc-
tion with the deck clutch engaged will shut
off the engine unless ignition key is placed
in the ROS "ON" position.
WARNING: Backing up with the deck
clutch engaged while mowing is strongly
discouraged. Turning the ROS "ON", to al-
low reverse operation with the deck clutch
engaged, should only be done when the
operator decides it is necessary to reposition
the machine with the attachment engaged.
Do not mow in reverse unless absolutely
necessary.
USING THE REVERSE OPERATION
SYSTEM -
Only use if you are certain no children or
other bystanders will enter the mowing
area.
1. Move motion control lever to neutral (N)
position.
2. With engine running, turn ignition key
counterclockwise to ROS "ON" position.
3. Look down and behind before and while
backing.
4. Slowly move motion control lever to
reverse (R) position to start movement.
5. When use of the ROS is no longer
needed, turn the ignition key clockwise
to engine "ON" position.
ROS "ON" Position Engine "ON" Position
(Normal Operating)
Mulch Cover
Bungee
Bungee
Mulch CoverDeflector Shield
2. Lift the mulch cover.
3. Attach the deflector to the hinge bracket.
4. Rest the mulch cover on the deflector.
5. Attach the 1 bungee from the deflector
to the deck.
Deflector
Shield
Hinge Bracket
TO TRANSPORT
When pushing or towing your riding mower,
be sure to disengage transmission by placing
shifter in neutral.
• Raise mower height adjustment to its high-
est position with mower height adjustment
lever.
• To reengage transmission, press brake
and shift out of neutral.
TO OPERATE ON HILLS
WARNING: Do not drive up or down
hills with slopes greater than 15° and do not
drive across any slope. Use the slope guide
at the back of this manual.
• Choose the slowest speed before starting
up or down hills.
• Avoid stopping or changing speed on
hills.
• If stopping is absolutely necessary, push
clutch/brake pedal quickly to brake posi-
tion and engage parking brake.
• Move motion control lever to neutral (N)
position.
• To restart movement, slowly release
parking brake and clutch/brake pedal.
• Make all turns slowly.
31
1 532 43 65-51 BATTERY
3 532 19 33-50 SWITCH, IGN, DLTA, P-IN, ROS
4 532 41 19-33 KEY/CHAIN
9 532 10 95-53 SWITCH, INTLK,CL, MWR, GRY
10 532 17 61-38 SWITCH, INTERLOCK, NONC,GRAY
12 532 19 27-49 SWITCH, SEAT, DP, ROS
13 532 43 72-28 HARNESS, IGN, ELECTSTART, LRV
15 532 19 25-07 SOLENOID
16 817 72 04-08 SCREW THD CUT 1/4-20 X 1/2 TY23
17 873 51 04-00 NUT KEPS HEX 1/4-20 UNC
18 532 41 66-94 CABLE BATTERY
19 532 42 12-99 CABLE STARTER
20 532 42 12-98 CABLE GROUND
21 817 06 05-12 SCREW 5/16-18 X 3/4
22 874 35 05-09 SCREW HEX M5X0.8.9MM
23 532 43 81-22 NUT M5
24 818 10 10-12 SCREW TORX #10-14 X .750
25 532 44 16-22 FUSE, 10
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
ELECTRICAL PRODUCT NUMBER 960 26 00-01

30
LRV2
10
9
12
1
34
25
23
22
24
13
15
17
16
20
21
19
18
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
ELECTRICAL PRODUCT NUMBER 960 26 00-01
15
ADD GASOLINE
• Fill fuel tank to bottom of filler neck. Do
not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil with
gasoline. Purchase fuel in quantities that
can be used within 30 days to assure fuel
freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline near
an open flame.
CAUTION: Alcoholblended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation
and formation of acids during storage. Acidic
gas can damage the fuel system of an engine
while in storage. To avoid engine problems,
the fuel system should be emptied before
storage of 30 days or longer. Drain the gas
tank, start the engine and let it run until the
fuel lines and carburetor are empty. Use
fresh fuel next season. See Storage Instruc-
tions for additional information. Never use
engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your riding mower has been
shipped, from the factory, already filled with
summer weight oil.
1. Check engine oil with riding mower on
level ground.
2. Remove oil fill cap/dipstick and wipe
clean, reinsert the dipstick and screw cap
tight, wait for a few seconds, remove and
read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do
not overfill.
• For cold weather operation you should
change oil for easier starting (See the oil
viscosity chart in the Maintenance section
of this manual).
• To change engine oil, see the Mainte-
nance section in this manual.
Fuel Cap
TO START ENGINE
When starting the engine for the first time or
if the engine has run out of fuel, it will take
extra cranking time to move fuel from the
tank to the engine.
• Sit on seat in operating position, depress
clutch/brake pedal and set parking brake.
• Place motion control lever in neutral
position.
• Move deck clutch lever to “DISEN-
GAGED” position.
• Move throttle control to choke position.
NOTE: Before starting, read the warm and
cold starting procedures below.
• Insert key into ignition and turn key clock-
wise to “START” position and release
key as soon as engine starts. Do not run
starter continuously for more than fifteen
seconds per minute. If the engine does
not start after several attempts, move
throttle control to fast position, wait a
few minutes and try again. If engine still
does not start, move the throttle control
back to the choke position and retry.
WARM WEATHER STARTING
(50°F/10°C AND ABOVE)
• When engine starts, move the throttle
control to the fast position.
• The ground drive can now be used. If the
engine does not accept the load, restart
the engine and allow it to warm up for
one minute using the choke as described
above.
COLD WEATHER STARTING
(50°F/10°C AND BELOW)
• When engine starts, allow engine to run
with the throttle control in the choke posi-
tion until the engine runs roughly, then
move throttle control to fast position. This
may require an engine warm-up period
from several seconds to several minutes,
depending on the temperature.

16
MOWING TIPS
• Mower should be properly leveled for best
mowing performance. See “TO LEVEL
MOWER HOUSING” in the Service and
Adjustments section of this manual.
• The left hand side of mower should be
used for trimming.
• Drive so that clippings are discharged
onto the area that has already been cut.
Have the cut area to the right of the riding
mower. This will result in a more even
distribution of clippings and more uniform
cutting.
• When mowing large areas, start by turning
to the right so that clippings will discharge
away from shrubs, fences, driveways,
etc. After one or two rounds, mow in the
opposite direction making left hand turns
until finished.
• If grass is extremely tall, it should be
mowed twice to reduce load and possible
fire hazard from dried clippings. Make
first cut relatively high; the second to the
desired height.
• Do not mow grass when it is wet. Wet
grass will plug mower and leave undesir-
able clumps. Allow grass to dry before
mowing.
• Regulate ground speed by selecting a low
enough gear to give the mower cutting
performance as well as the quality of cut
desired.
• When operating attachments, select a
ground speed that will suit the terrain and
give best performance of the attachment
being used.
29
BATTERY
FUSE
DER
RED
RED
WHITE
BLACK
BLUE
BLACK
BLACK
BLACK/WHITE
BLUE
BLACK
BLACK
GRAY
GRAY
BLACK
SOLENOID
M
STARTER
CLUTCH / BRAKE
(PEDAL UP)
SEAT SWITCH
(NOT OCCUPIED)
IGNITION
UNIT
FUEL SHUT-OFF
SOLENOID
SM
B
GA1
A2
L
REVERSE SWITCH
SPARK PLUGS
GAP
(2 PLUGS
ON TWIN CYL. ENGINES)
NOT IN REVERSE SHORTING CONNECTOR
ATTACHMENT CLUTCH
(CLUTCH OFF)
REMOVABLE
CONNECTIONS
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED CLIPS
WERE REMOVED FOR SERVICING OF
UNIT, THEY SHOULD BE RE-INSTALLED
TO PROPERLY SECURE YOUR WIRING.
IGNITION SWITCH
CIRCUITPOSITION
OFF
B+A1
RUN/OVERRIDE
B+S+A1START
M+G+A1
B+A1RUN
“MAKE”
L+A2
NON-REMOVABLE
CONNECTIONS
STATOR
DIODE
28 VOLTS AC MIN. @ 3600 RPM
(CHARGING SYSTEM DISCONNECTED)
CHARGING SYSTEM OUTPUT
3 AMP DC @ 3600 RPM
(IF EQUIPPED)
SCH24
RIDING MOWER MODEL NUMBER WELRVBA (96026000100)
SCHEMATIC PRODUCT NUMBER 960 26 00-01