Weed Eater 530088774 User manual

ENGLISH FRANÇAIS
ESPAÑOL
BC2400
Operator’s Manual
Manual del Operador
Manuel de L’utilisateur
For Occasional Use Only
UL
R
Copyright E2000 WCI Outdoor Products, Inc.
DANGER:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
PELIGRO:
Lea el manual del operador y siga todas las advertencias e instruc-
ciones de seguridad. El no hacerlo puede resultar en lesiones graves.
DANGER:
Lire le manuel de l’utilisateur et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
530088774 11/21/00
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Augusta, GA 30907
RTrademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com

2
SAFETY RULES
WARNING: When using gardening
appliances, basic safety precautions should
always be followed to reduce the risk of fire
and serious injury. Read and follow all
instructions. Failure to do so can result in se-
rious injury.
DANGER: This power tool can be
dangerous! This unit can cause serious injury
including amputation or blindness to the op-
erator and others. The warnings and safety
instructions in this manual must be followed to
provide reasonable safety and efficiency in
using the unit. The operator is responsible for
following the warnings and instructions in this
manual and on the unit. Read the entire Op-
erator’s Manual before assembling and using
the unit! Restrict the use of this unit to persons
who read, understand, and follow the warn-
ings and instructions in this manual and on the
unit. Never allow children to operate this unit.
SAFETY INFORMATION
ON THE UNIT
OPERATORS
MANUAL
DANGER: Blade can thrust violently
away from material it does not cut. Blade
thrust can cause amputation of arms or legs.
Keep people and animals 50 feet (15 meters)
away.
WARNING: Trimmer line can throw
objects violently. You and others can be
blinded or injured. Wear safety glasses and
leg protection.
Leg Guards
Boots
Eye
Protection
ALWAYS WEAR:
Thrown
Objects
WARNING: Hazard zone for thrown
objects. Blade/Trimmer line can throw objects
violently. Others can be blinded or injured.
Keep people and animals 50 feet (15 meters)
away.
Hazard Zone
50 Feet
(15 Meters)
WARNING: Do not use trimmer head
as a fastening device for the blade.
WARNING: The blade continues to
spin after the throttle is released or, engine is
turned off. The coasting blade can throw objects
or seriously cut you if accidentally touched. Stop
the blade by contacting the left hand side of the
coasting blade with material already cut.
Stop coasting
blade by contact
with cut material
.
OPERATOR SAFETY
SDress properly. Always wear safety
glasses or similar eye protection when op-
erating, or performing maintenance on your
unit. (Safety glasses are available.) Eye
protection should meet the requirements of
ANSI Z87.1 and be marked Z87.
SAlways wear face or dust mask if operation
is dusty.
SAlways wear heavy, long pants, long
sleeves, boots, and gloves. Wearing safe-
ty leg guards is recommended.
SAlways wear foot protection. Do not go
barefoot or wear sandals.
SSecure hair above shoulder length. Secure or
remove loose clothing and jewelry or clothing
with loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
SBeing fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line/blade.
SStay Alert. Do not operate unit when you are
tired, ill, or under influence of alcohol, drugs,
or medication. Watch what you are doing; use
common sense.
SWear hearing protection.
SNever start or run the engine inside a
closed room or building. Breathing exhaust
fumes can kill.
SKeep handles free of oil and fuel.

3
SAlways use the handlebar and a properly
adjusted shoulder strap with a blade (see
ASSEMBLY).
UNIT/MAINTENANCE SAFETY
WARNING: Stop unit and disconnect
the spark plug before performing mainte-
nance (except carburetor adjustments).
SLook for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep unit in good
working condition.
SThrow away blades that are bent, warped,
cracked, broken, or damaged in any other
way. Replace trimmer head parts that are
cracked, chipped, broken, or damaged in
any other way before using the unit.
SMaintain unit according to recommended
procedures. Keep blade sharp. Keep cut-
ting line at the proper length.
SUse only 0.080” (2 mm) diameter Weed
EaterRbrand line. Never use wire, rope,
string, etc.
SInstall required shield properly before using
the unit. Use the metal shield for all metal
blade use. Use the plastic shield for all line
trimmer use.
SUse only specified blade or trimmer head;
make sure it is properly installed and se-
curely fastened.
SNever start engine with clutch shroud re-
moved. The clutch can fly off and cause se-
rious injury.
SBe sure blade or trimmer head stops turning
when engine idles.
SMake carburetor adjustments with the low-
er end supported to prevent blade or trim-
mer line from contacting any object. Hold
unit by hand; do not use the shoulder strap
for support.
SKeep others away when making carburetor
adjustments.
SUse only recommended Weed EaterRac-
cessories and replacement parts.
SHave all maintenance and service not ex-
plained in this manual performed by your Au-
thorized Service Dealer.
FUEL SAFETY
SMix and pour fuel outdoors.
SKeep away from sparks or flames.
SUse a container approved for fuel.
SDo not smoke or allow smoking near fuel or
the unit or while using the unit.
SAvoid spilling fuel or oil. Wipe up all fuel
spills before starting engine.
SMove at least 10 feet (3 meters) away from fu-
eling site before starting engine.
SStop engine and allow it to cool before re-
moving fuel cap.
SEmpty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
SStore unit and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
SAlways store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area to be
cut before each use. Remove objects (rocks,
broken glass, nails, wire, string, etc.) which
can be thrown or become entangled in the
blade or trimmer head.
SKeep others including children, animals,
bystanders, and helpers at least 50 feet (15
meters) away. Stop engine immediately if
you are approached.
SAlways keep engine on the right--hand side
of your body.
SHold the unit firmly with both hands.
SKeep firm footing and balance. Do not over-
reach.
SKeep blade or trimmer head below waist
level. Do not raise engine above your waist.
SKeep all parts of your body away from
blade, trimmer head, and muffler when en-
gine is running. A hot muffler can cause se-
rious burns.
SCut from your right to your left.
SUse only in daylight or good artificial light.
SUse only for jobs explained in this manual.
TRANSPORTING AND STORAGE
SStop the unit before carrying.
SKeep muffler away from your body.
SAllow the engine to cool and secure the unit
before storing or transporting it in a vehicle.
SEmpty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
SStore unit so the blade or line limiter blade
cannot accidentally cause injury. The unit
can be hung by the tube.
SStore unit out of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal

4
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by your Au-
thorized Service Dealer.
ASSEMBLY
CARTON CONTENTS
Check carton contents for the following:
Sbrushcutter
Shandlebar screws (2)
Sblade shield screws (4)
Scupped washer
Slarge nut for installing blade
Slong hex wrench
Sshort hex wrench
Sbracket cover
Smetal shield
Splastic shield
Sshoulder strap with warning
Sweed blade
Strimmer head (assembled on unit)
Shandlebar
Scontainer of oil
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the empty
fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing done
by the manufacturer.
ASSEMBLY
WARNING: Always stop unit and dis-
connect spark plug before performing any as-
sembly procedures.
WARNING: Make sure your unit is
properly assembled and all fasteners are se-
cure.
TOOLS REQUIRED
S2 Hex wrenches (provided)
SAdjustable wrench or large pliers
SPhillips screwdriver
ATTACHING THE HANDLEBAR
DANGER: During blade usage, the
barrier portion of the handlebar must be
installed as shown to provide a barrier be-
tween operator and the spinning blade.
SLocate the decal on the handlebar. This de-
cal includes two arrows. Position the han-
dlebar with the mounting bracket between
these arrows.
SPosition the bracket cover over the handle-
bar. Again make sure the handlebar is be-
tween the arrows.
SInsert screws and hand tighten only. Be
sure the handlebar is installed correctly;
then, tighten each screw securely with the
short hex wrench.
Bracket Cover
Screw
Mounting
Bracket
Handlebar
ASSEMBLY OF SHOULDER STRAP
WARNING: Proper shoulder strap
and handlebar adjustments before starting the
engine are required.
STry on shoulder strap and adjust for fit and
balance before starting the engine or begin-
ning a cutting operation.
SInsert your right arm and head through the
shoulder strap and allow it to rest on your
left shoulder. Make sure the danger sign is
on your back and the hook is to the right
side of your waist.
NOTE: A one-half twist is built in the shoul-
der strap to allow the strap to rest flat on the
shoulder.
SAdjust the strap, allowing the hook to be
about 6 inches below the waist.
SFasten the strap hook to the clamp located
between the trigger handle and the handle-
bar clamp base and lift the tool to the oper-
ating position.
CONFIGURING YOUR UNIT
You can configure your unit using a cutting
head for grass and light weeds, or a weed
blade for cutting grass, weeds, and brush up
to 1/2 inch in diameter. To assemble your unit,
go to the section for the desired configuration
and follow the instructions.
ASSEMBLY INFORMATION --
TRIMMER HEAD
TRIMMER
HEAD
NOTE: Remove the blade and metal shield
before attaching the plastic shield and trim-
mer head. To remove blade, push in locking
lever and hold. Rotate blade nut until the lock-
ing lever falls into one of the grooves in the
dust cup. Continue to hold the locking lever.
This will keep the shaft from turning while
loosening the blade nut. Remove blade nut
by turning clockwise. Release locking lever.
Remove both washers and blade. To remove
metal shield, loosen and remove the four
mounting screws. See ATTACHING THE
METAL SHIELD and INSTALLING THE
METAL BLADE for illustrations. Be sure to
store all parts and instructions for future use.

5
ATTACHING THE PLASTIC SHIELD
AND TRIMMER HEAD
WARNING: The shield must be prop-
erly installed. The shield provides partial
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line to
the proper length. The line limiter blade (on
underside of shield) is sharp and can cut you.
SRemove wing nut from shield.
SInsert bracket into slot on shield.
SPivot shield until bolt passes through hole in
bracket.
STighten the wing nut securely.
SIf your unit has a plastic cover over the
threads on the threaded shaft, remove the
covering to expose the threads.
SBefore installing the trimmer head, make
sure the dust cup and retaining washer are
positioned on the gearbox as shown below.
Wing Nut
Retaining Washer
Dust Cup
Bracket
Slot
Shield Gearbox
NOTE: Make sure all parts are properly
installed as shown in the illustration before
installing the trimmer head.
SPush in locking lever and hold.
SRotate dust cup until the locking lever falls
into one of the grooves.
Locking Lever
SContinue to hold in locking lever. This will
keep the shaft from turning while tightening
the trimmer head.
SThread trimmer head onto the shaft in the
direction shown on the decal. Tighten until
secure.
SRelease locking lever.
NOTE: The retaining washer must be posi-
tioned with the raised section toward the
gearbox.
ASSEMBLY INFORMATION -- WEED
BLADE
WEED
BLADE
NOTE: Remove the trimmer head and plastic
shield before attaching the metal shield and
installing the weed blade. To remove the trim-
mer head, push in locking lever and hold. Ro-
tate trimmer head until the locking lever falls into
one of the grooves in the dust cup. Continue to
hold in locking lever. This will keep the shaft
from turning while loosening the trimmer head.
Remove trimmer head by turning clockwise.
Release locking lever. To remove the plastic
shield, loosen and remove wing nut. Pivot
shield to release bracket from slot. See AT-
TACHING THE PLASTIC SHIELD AND TRIM-
ER HEAD for illustrations. Be sure to store all
parts and instructions for future use. Never use
the trimmer head with the metal blade installed.
ATTACHING THE METAL SHIELD
DANGER: The metal shield must be
properly installed on the tool anytime the tool
is used with the blade. The forward tip of the
metal shield helps to reduce the occurrence
of blade thrust which can cause serious injury
such as amputation to the operator or by-
standers. Failure to install the shield in the
position shown can result in serious injury to
the operator. The length of the shield must be
aligned with the length of the tube. The blade
is sharp and can cut you. Be sure to wear
gloves while working with blades.
SIf your unit has a plastic cover over the
threads on the shaft, remove the covering
to expose the threads.
SPlace the metal shield under the gearbox,
and align the screw holes.
Shield Gearbox
SInsert and thread the 4 mounting screws
through the holes of the gearbox and the
metal shield. Tighten evenly and securely
with the hex wrench provided.

6
INSTALLATION OF THE METAL
BLADE
WARNING: Do not use any blades, or
fastening hardware other than the washers and
nuts shown in the following illustrations. These
parts must be provided by Poulan/Weed Eater,
and installed as shown below. Failure to use
proper parts can cause the blade to fly off and
seriously hurt you or others.
NOTE: The dust cup and retaining washer are
located on the gearbox and not in the parts bag.
SRemove the retainer washer from the gear-
box, and leave the dust cup on the gearbox.
NOTE: It may be necessary to remove a
plastic protective covering from the
threaded shaft before removing the retain-
ing washer.
Retaining
Washer
Dust Cup
SInstall the blade over the threaded shaft ex-
tending from the gearbox between the dust
cup and the retaining washer. Make sure
the raised part of the retaining washer is
facing the gearbox, and the raised area fits
into the hole in the center of the blade.
SSlide the blade and retaining washer onto
the shaft of the gearbox.
SNow place the cupped washer onto the
shaft. Make sure the cupped side of the
washer is toward the blade.
SInstall the blade nut by threading onto the
shaft counterclockwise.
Shield
Blade
Retaining
Washer
Dust Cup
Cupped
Washer
Nut
Threaded Shaft
NOTE: Make sure all parts are in place as illus-
trated, and the blade is sandwiched between
the dust cup and the retaining washer. There
should be no space between the blade and the
dust cup or the retaining washer.
SPush in locking lever and hold.
SRotate blade nut until the locking lever falls
into one of the grooves in the dust cup.
Locking Lever
SContinue to hold in locking lever. This will
keep the shaft from turning while tightening
the blade nut.
STighten blade nut firmly with a wrench.
SRelease locking lever.
STurn blade by hand. If the blade binds
against the shield, or appears to be uneven,
the blade is not centered, and you must re-
install.
FUEL YOUR UNIT
This engine is certified to operate on unleaded
gasoline. Gasoline must be mixed with a good
quality 2-cycle air-cooled engine oil designed to
be mixed at a ratio of 40:1. Poulan/Weed Eater
brand oil is recommended. (A 40:1 ratio is ob-
tained by mixing 3.2 ounces of oil with 1 gallon of
unleaded gasoline). When mixing fuel follow the
instructions printed on the container. Always
read and follow the safety rules under FUEL
SAFETY.
STARTING
HOW TO STOP YOUR UNIT
To stop the engine, move the ON/OFF switch
to the OFF position.
HOW TO START YOUR UNIT
Starting Position
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
SRest engine and shield on ground, support-
ing trimmer head off ground.

7
Throttle Trigger
ON/OFF
Switch
Choke
Lever
Primer Bulb
Starter
Handle
Muffler
COLD ENGINE (or warm engine af-
ter running out of fuel)
SMove the ON/OFF switch to the ON posi-
tion.
SSlowly press the primer bulb 6 times.
SMove choke lever to FULL CHOKE posi-
tion.
SSqueeze the throttle trigger fully and hold
through all remaining steps.
SPull starter rope handle sharply 6 times.
SMove choke lever to HALF CHOKE posi-
tion.
SPull starter rope handle no more than 6
pulls, until engine runs.
SAllow engine to run 10 seconds, then move
choke lever to OFF CHOKE position.
STARTING A WARM ENGINE
SMove the ON/OFF switch to the ON posi-
tion.
SMove choke lever to OFF CHOKE position.
SPull starter rope handle until engine runs.
SIf engine does not start in 5 pulls, follow in-
structions in STARTING A COLD ENGINE.
USING YOUR UNIT
OPERATING POSITION
SExtend your left arm and hold handlebar
grip with your left hand.
SHold throttle grip with your right hand with
finger on throttle trigger.
SKeep unit below waist level.
SKeep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
SMaintain full weight of tool on your left
shoulder.
SWithout bending over, keep the blade or
trimmer head near and parallel to the
ground and not crowded into material being
cut.
OPERATING INSTRUCTIONS FOR
USE WITH TRIMMER HEAD
Before trimming, bring engine to a speed suffi-
cient to cut material to be trimmed.
Do not run engine at a higher speed than nec-
essary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise
and vibration. The cutting line will last longer
and will be less likely to “weld” onto the spool.
If trimmer head does not turn when the engine
is in operation, make sure the tube is properly
seated in engine shroud.
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
To stop engine:
SMove the ON/OFF switch to OFF.
SIf engine does not stop, move choke to
the FULL CHOKE position.
ADVANCING THE TRIMMER LINE
Advance line by tapping the bottom of the cut-
ting head lightly on the ground while engine is
running at full speed. The line limiter blade (on
underside of shield) will cut the line to the proper
length.
WARNING: Use only 0.080” (2 mm)
diameter line. Other sizes of line will not ad-
vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
OPERATING INSTRUCTIONS FOR
USE WITH WEED BLADE
SBlade Thrust is a reaction that only occurs
when using a bladed unit. This reaction can
cause serious injury such as amputation.
Carefully study this section. It is important that
you understand what causes blade thrust,
how you can reduce the chance of its occur-
ring, and how you can remain in control of unit
if blade thrust occurs.
SWHAT CAUSES BLADE THRUST -- Blade
Thrust can occur when the spinning blade
contacts an object that it does not cut. This
contact causes the blade to stop for an instant
and then suddenly move or “thrust” away
from the object that was hit. The “thrusting” re-
action can be violent enough to cause the op-
erator to be propelled in any direction and lose
control of the unit. The uncontrolled unit can
cause serious injury if the blade contacts the
operator or others.
SWHEN BLADE THRUST OCCURS --
Blade Thrust can occur without warning if
the blade snags, stalls, or binds. This is
more likely to occur in areas where it is diffi-

8
cult to see the material being cut. By using
the unit properly, the occurrence of blade
thrust will be reduced and the operator will
be less likely to lose control.
SCut only grass, weeds, and woody brush up
to 1/2 inch in diameter with the weed blade.
Do not let the blade contact material it can-
not cut such as stumps, rocks, fences,
metal, etc., or clusters of hard, woody brush
having a diameter greater than 1/2 inch.
SKeep the blade sharp. A dull blade is more
likely to snag and thrust.
SCut only at full throttle. The blade will have
maximum cutting power and is less likely to
bind or stall.
S“Feed” the blade deliberately and not too
rapidly. The blade can thrust away if it is fed
too rapidly.
SCut only from your right to your left. Swing-
ing the unit in the same direction as the
blade spins increases the cutting action.
SUse the shoulder strap and keep a firm grip
on the unit with both hands. A properly ad-
justed shoulder strap will support the
weight of the unit, freeing your arms and
hands to control and guide the cutting mo-
tion.
SKeep feet comfortably spread apart and
braced for a possible sudden, rapid thrust of
unit. Do not overreach. Keep firm footing and
balance.
SKeep blade below waist level; it will be eas-
ier to maintain control of unit.
SDo not raise the engine above your waist as
the blade can come dangerously close to
your body.
SDo not swing unit with such force that you
are in danger of losing your balance.
Bring the engine to cutting speed before en-
tering the material to be cut.
If the blade does not turn when you squeeze
the throttle trigger, make sure tube is fully in-
serted into the engine.
Always release the throttle trigger and allow
engine to return to idle speed when not cut-
ting. The blade should not turn while the en-
gine is running at idle. If the blade turns at idle,
do not use your unit. Refer to the Carburetor
adjustment section or contact your Autho-
rized Service Dealer.
SMaintain good firm footing while using the
unit. Do this by planting feet firmly in a com-
fortable apart position.
SCut while swinging the upper part of your
body from right to left.
SAs you move forward to the next area to cut,
be sure to maintain your balance and foot-
ing.
Cut using the 8 o’clock
to 10 o’clock position of
the blade
10 o’clock
8 o’clock
WARNING: The operator or others
must not try to clear away cut material with the
engine running or the blade turning to avoid
serious injury. Stop engine and blade before
removing materials wrapped around blade or
tube.
REPLACING THE LINE
SMove the ON/OFF switch to the OFF posi-
tion and ensure trimmer head has fully
stopped.
SRemove the spool by firmly pulling on the
tap button.
SClean entire surface of hub and spool.
SReplace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080” (2 mm) di-
ameter Weed EaterRbrand line. Never use
wire, rope, string, etc., which can break off
and become a dangerous missile.
SInsert ends of line about 1/2 inch (1 cm) into
the small holes on the inside of the spool.
Small
Holes
Spool
Hub
Line in Notch
Line in Notch
Line exit holes
SWind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
SPush the lines into the notches, leaving 3 to
5 inches (7 -- 12 cm) unwound.
SInsert the lines into the the exit holes in the
hub as shown in the illustration.
SAlign notches with the line exit holes.
SPush the spool into the hub until it snaps
into place.
SPull the lines extending outside of the hub to
release the lines from the notches.

9
SERVICE
We recommend all service and adjustments
not listed in this manual be performed by an
Authorized Service Dealer.
CARBURETOR ADJUSTMENT
Your carburetor is equipped with limiter caps.
Damage will occur if you turn the needles be-
yond the limiter caps. Adjusting the carburetor is
a complicated task. We recommend that you
take your unit to an Authorized Service Dealer.
SPARK PLUG
Replace spark plug yearly with a Champion
RCJ-8Y plug. Spark plug gap is 0.025 inches.
IGNITION TIMING
Ignition timing is fixed, non-adjustable.
NEED ASSISTANCE?
NEED ASSISTANCE?
Call 1-800-554-6723.
NEED SERVICE PART?
Contact your dealer.
TROUBLE CAUSE REMEDY
Engine will not
start.
SEngine flooded.
SFuel tank empty.
SSpark plug not firing.
SFuel not reaching carburetor.
SCarburetor requires adjustment.
SSee “Starting.”
SFill tank with correct fuel mixture.
SInstall new spark plug.
SCheck for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
SSee “Carburetor Adjustments.”
Engine will not
idle properly.
SCarburetor requires adjustment.
SThrottle trigger screw too
tight.
SSee “Carburetor Adjustments.”
SLoosen screw.
SAir filter dirty.
SSpark plug fouled.
SCarburetor requires adjustment.
Engine will not
accelerate,
lacks power,
or dies under
a load.
SClean or replace air filter.
SClean or replace spark plug; re-gap.
SSee “Carburetor Adjustments.”
Engine
smokes
excessively.
SFuel mixture incorrect.
SAir filter dirty.
SCarburetor requires adjustment.
SEmpty fuel tank and refill with
correct fuel mixture.
SClean or replace air filter.
SSee “Carburetor Adjustments.”
Line does not
advance or
breaks while
cutting.
SLine improperly routed in head.
SLine improperly wound on
spool.
SLine size incorrect.
SCheck line routing.
SRewind line tightly and evenly.
SUse only 0.080” (2 mm) dia. line.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of th
e
recommended remedies below other than remedies that require operation of the unit.
Line welds
onto spool.
Line pulls
back into
head.
SLine size incorrect.
SIncorrect spool.
SLine is being crowded against
material being cut.
SUse only 0.080” (2 mm) dia. line.
SReplace with correct spool.
SCut with tip of line fully extended.
SToo little line outside of head.
SLine size incorrect.
SRemove spool and pull 4 inches
(10 cm) of line outside of head.
SUse only 0.080” (2 mm) dia. line.

10
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS
NORTH AMERICA, Division of WCI Out-
door Products, Inc., warrants to the original
purchaser that each new Weed Eater!
!!
!
brand gasoline tool or attachment is free from
defects in material and workmanship and
agrees to repair or replace under this war-
ranty any defective gasoline product or at-
tachment as follows from the original date of
purchase.
2 YEARS-- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income produc-
ing purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use
of accessories and/or attachments not spe-
cifically recommended by ELECTROLUX
HOME PRODUCTS NORTH AMERICA for
this tool. Additionally , this warranty does not
cover tune-ups, spark plugs, filters, starter
ropes, starter springs, cutting line, or rotating
head parts that will wear and require replace-
ment with reasonable use during the warranty
period. This warranty does not cover prede-
livery setup or normal adjustments explained
in the operator ’s manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
ELECTROLUX HOME PRODUCTS
NORTH AMERICA’S policy is to continu-
ously improve its products. Therefore, ELEC-
TROLUX HOME PRODUCTS NORTH
AMERICA reserves the right to change, mod-
ify, or discontinue models, designs, specifica-
tions, and accessories of all products at any
time without notice or obligation to any pur-
chaser.
U.S. EPA
EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental
Protection Agency and POULAN/WEED
EATER, DIVISION OF WCI OUTDOOR
PRODUCTS are pleased to explain the
emissions control system warranty on your
lawn and garden equipment engine. All new
utility and lawn and garden equipment en-
gines must be designed, built, and equipped
to meet the stringent anti--smog standards.
POULAN/WEED EATER must warrant the
emission control system on your lawn and
garden equipment engine for the periods of
time listed below provided there has been no
abuse, neglect, or improper maintenance of
your lawn and garden equipment engine.
Your emission control system includes parts
such as the carburetor and the ignition sys-
tem. Where a warrantable condition exits,
POULAN/WEED EATER will repair your
lawn and garden equipment engine at no
cost to you. Expenses covered under war-
ranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions related part on
your engine (as listed under Emissions Con-
trol Warranty Parts List) is defective or a de-
fect in the materials or workmanship of the
engine causes the failure of such an emis-
sion related part, the part will be repaired or
replaced by POULAN/WEED EATER.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the lawn and garden equipment en-
gine owner, you are responsible for the per-
formance of the required maintenance listed
in your Owner’s Manual. POULAN/WEED
EATER recommends that you retain all re-
ceipts covering maintenance on your lawn
and garden equipment engine, but POULAN/
WEED EATER cannot deny warranty solely
for the lack of receipts or for your failure to
ensure the performance of all scheduled
maintenance. As the lawn and garden
equipment engine owner, you should be
aware that POULAN/WEED EATER may
deny you warranty coverage if your lawn and
garden equipment engine or a part of it has
failed due to abuse, neglect, improper main-
tenance, unapproved modifications, or the
use of parts not made or approved by the
original equipment manufacturer. You are
responsible for presenting your lawn and
garden equipment engine to a POULAN/
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount
of time, not to exceed 30 days. If you have
any questions regarding your warranty rights
and responsibilities, you should contact your
nearest authorized service center or call
POULAN/WEED EATER at
1--800--554--6723. WARRANTY COM-

11
MENCEMENT DATE: The warranty period
begins on the date the lawn and garden
equipment engine is purchased. LENGTH
OF COVERAGE: This warranty shall be for
a period of two years from the initial date of
purchase. WHAT IS COVERED: REPAIR
OR REPLACEMENT OF PARTS. Repair or
replacement of any warranted part will be
performed at no charge to the owner at an
approved POULAN/WEED EATER servic-
ing center. If you have any questions regard-
ing your warranty rights and responsibilities,
you should contact your nearest authorized
service center or call POULAN/WEED EAT-
ER at 1--800--554--6723 WARRANTY PE-
RIOD: Any warranted part which is not
scheduled for replacement as required
maintenance, or which is scheduled only for
regular inspection to the effect of “repair or
replace as necessary” shall be warranted for
2 years. Any warranted part which is sched-
uled for replacement as required mainte-
nance shall be warranted for the period of
time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved POULAN/
WEED EATER servicing center. CONSE-
QUENTIAL DAMAGES: POULAN/WEED
EATER may be liable for damages to other
engine components caused by the failure of
a warranted part still under warranty. WHAT
IS NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance
are not covered. ADD--ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. POULAN/WEED EATER is not liable
to cover failures of warranted parts caused
by the use of add--on or modified parts.
HOW TO FILE A CLAIM: If you have any
questions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized service center or call
POULAN/WEED EATER at
1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all POULAN/
WEED EATER service centers. call:
1--800--554--6723 MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any POULAN/WEED
EATER approved replacement part used in
the performance of any warranty mainte-
nance or repair on emission related parts will
be provided without charge to the owner if
the part is under warranty. EMISSION CON-
TROL WARRANTY PARTS LIST: Carbure-
tor, Ignition System: Spark Plug (covered up
to maintenance schedule), Ignition Module.
MAINTENANCE STATEMENT: The owner
is responsible for the performance of all re-
quired maintenance as defined in the own-
er’s manual.