Weed Eater Featherlite SST25 User manual

_) Tradema[k
&
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner I'outil au detaillant.
•1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d'lnstructions
SST25 !
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENClA:
Lea el manuaI de instrucciones y siga todas Ias advertencias e
instrucciones de seguridad. Et no hacerlo puede resultar en Iesiones
graves.
AVERTISSEMENT:
Lire le manuel d'instructions et bien respecter tous Ies avertisse-
ments et toutes Ies instructions de securit& Tout defaut de tefaire
pourrait entraTner des blessures graves.
WEED EATER WEED EATER
1030 Stevens Creek Road 6150 McLaughlin Road
Augusta, GA 30907 Mississauga, Ontario L5R4C2
545186735 Rev. 1 4/15/08 BRW

dabWARNING: When using gardening
appliances, basic safety precautions must al-
ways be folfewed to reduce the risk of fire and
serious injury. Read and folfew all instruc-
tions.
This power unit can be dangerous! Operator is
responsible for following instructions and warn-
ings on unit and in manual Read entire instruc-
tion manual before using unit! Be thoroughly fa-
miliar with the controls and the proper use of the
unit. Restrict the use of this unitto persons who
have read, understand, and will folfew the
instructions and warnings on the unit and in the
manual Never allow children to operate this
unit.
INSTRUCTION SAFETY INFORMATION
MANUAL ON THE UNIT
_ll DANGER: Never use blades or flailing
devices This unit is designed for line trimmer
use only. Use of any other accessories or at-
tachments witl increase the risk of injury.
Q©O
_1_WARNING: Trimmer line throws ob-
jects wefently You and others can be blioded/in-
jured Wear eye and leg protection. Keep body
parts cfear of rotating _ine
_Boots (x _._,_,
Keep children, bystanders, and animals 50 feet
(f5 meters) awa_ If approached stop unit im-
mediately.
If situations occur which are not covered in
this manual, use care and good judgment, if
you need assistance, contact your authorized
service deaIer or ca_l 1-800-554-8723.
OPERATOR SAFETY
• Dress proberty. Always wear safety gtasses
or similar eye protection when operating, or
performing maintenance, on your unit (safety
glasses are available). Eye protection should
be marked Z87.
• Always wear face or dust mask if operation is
dusty.
• Always wear heavy, long pants, long sleeves,
boots, and gloves Wearing safety leg guards
is recommended
• Always wear foot protection. Do not go bare-
foot or wear sandals Stay clear of spinning
line.
• SecurehairabovesbeuIderlength. Secureor
remove loose clothing or clothing with loosely
hanging ties, str_, tassefs, etc. They can
be caught in moving parts.
• Being folly covered also helps protect you
from debris and pieces of toxic plants thrown
by spinning line.
• Stay Alert Do not operate this unfl when you
are tired, ilI, upset or under the influence of al-
cbeef, drugs, or medication. Watch what you
are doing; use common sense.
• Wear hearing protection.
• Never start or run inside a cfesed room or
building. Breathing exhaust fumes can kifL
• Keep handles free of oil and fuel
UNIT /MAINTENANCE SAFETY
• Disconnect the spark plug before performing
maintenance except carburetor adjustments.
• Look for and replace damaged or loose parts
before each use. Look for and repair fuel
leaks before use Keep in good working
cood_ion.
• Replace trimmer head parts that are chipped,
cracked, broken, or damaged in any other
way before using the unit.
• Maintain unit according to recommended pro-
cedures. Keep cutting line at proper length.
• Use only 0.080" (2 ram) diameter WEED
EATER brand line. Never use wire, rope,
string, etc.
•InstalI required shield properly before using
the unfl. Use only specked trimmer head;
make sure itis proberly installed and securely
fastened.
• Make sure unit is assembled correcfly as
shown in this manual
• Make carburetor adjustments with lower end
supported to prevent line from contacting any
object.
• Keep others away when making carburetor
adjustments.
• Use only recommended WEED EATER ac-
cessories and replacement parts
• Have efl maintenance and service not ex-
plained in this manual performed by an autho-
rized service dea_er.
FUEL SAFETY
• Mix and pour fuel outdoors.
• Keep away from sparks or flames.
• Use a container approved for fuel.
• Do not smoke or allow smoking near fuef or
the unit.
• Avoid spilling fuel or oil W_be up all fuel spills.
• Move at least 10 feet (3 meters) away from
fueling site before starting engine.
• Stop engine and allow to cool before remov-
ing fuel cap.
• Always store gasoline in a container ap-
proved for flammable liquids.

CUTTINGSAFETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
• Use only for+rimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming
• Keep firm footing and balance. Do not over-
reach.
• Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level A hot muffler can cause serious burns.
• Cut from your left to your right. Cutting on
right side of the shield will throw debris away
from the operato£
• Use only in daylight or good art_cial light
• Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
• Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
• Empty the fuel tank before storing or trans-
porting the unit. Use up fuef Ieft in the carbure-
tor by sta_ng the engine and letting it run urr_l
it stops.
• Store unit and fuel in area where fuel vapors
cannot reach sparks or open 1lames from wa-
ter heaters, electric motors or switches, fur-
naces, ets
• Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the
shaft
• Store unrt out of reach of children.
_IIWARNING: The engine exhaust
from this product contains chemicals known
to the State of California to cause cancer, birth
defects or other reproductive harm.
SAFETY NOTICE: Exposure to vibrabons
through prolonged use of gasoline powered
hand tools could cause blood vesse} or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swefIings Prolonged use in cold
weather has been linked to blood vessef dam-
age in otherwise healthy people. Ifsymptoms
Occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ica_ attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. AIi
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen, tfyou
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violabon of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service After
50 hours of use, we recommend that your
muffler be serviced or replaced by your autho-
rized service dealer.
_1_WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and al_fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ADJUSTING THE HANDLE
,d_ WARNING: When adjusting the assist
handle, be sure itremains above the safety label
and below the mark or arrow on the shaft.
1 Loosen wing nut on handle.
2. Rotata the handfe on the shaff to an updght
position; retighten wing nut.
ATTACHING SHIELD
_,WARNING: Theshiefdmustbeprop-
erlyinstalled. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess Iine to the proper
length. The line Iimiter blade (on underside of
shield) is sharp and can cut you.
For proper orientation of sNefd, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
1. Remove wing nut from shield.
2. Insert bracket into sIot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
4- Securely tighten wing nut onto bolt

Bracket
S_ot WingNut
PIVOT Shield
KNOW YOUR TRIMMER
READTHISiNSTRUCTIONMANUALANDSAFETYRULESBEFOREOPERATINGYOURUNIT
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Muffler
Trimmer Shaft
Head
-&Pi,, 1
_'_,_._hieid
Line Limiter
Blade
Primer
Spark Plug k_ Bulb Trigger
STOP
Fuel Mix FiII Cap
Starter Handle
STOP SWITCH
The STOP sw_tch is used to stop the engine. To
stop the engine, push and bald the sw_tch in the
STOP position unti_the engine stops.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This aflows you to start the engine with fewer
pulis on the starter rope Activate the primer
bu}b by pressing it and alIowing it to return to
its edgina_ form.
CHOKE
The CHOKE helps to suppty fuel to the engine
to aid in cold sta_ng. Activate the choke by
moving the choke lever to the PULL CHOKE
position After the engine attempts to start, move
the choke tever to the HALF CHOKE pos_on.
Once engine has started, move the choke lever
to the RUN position
BEFORE STARTING ENGINE
_ WARNING: Be sureto reed the fuel
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fue_your unit. CalI
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certifiedto operate on unleaded
gasefine. Before operation, gasoline must be
mixed w_th a good quality synthetic 2-cycle
air-cooled engineoildesigned to be mixedat a
ratio of 40:1. Poulan/WEED EATER brand
syntheticoil isrecommended.Mixgasolineand
4

oil at a ratio of 40:f A 40:1 ratio is obtained by
mixing 32 ounces (95 mI) of oil with 1 gatlon (4
liters) of unleaded gasoline. DO NOT USE
automotive oil or marine oil These oils will
cause engine damage. When mixing fuel, follow
instructions printed on container Once oil is
added to gasoline, shake container momentadIy
to assure that the fuel is thorougNy mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids du ring stor-
age Acidic gas can damage the fuet system
of an engine while in storage To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor clean-
er products in the fuel tank or permanent dam-
age may occur. See the STO RAG E section for
additional information.
HOW TO STOP YOUR UNIT
• Tostopthe engine, push and hold the STOP
switch in the STOP position until the engine
stops.
• If engine does not stop, move choke to the
FULL CHOKE position.
HOW TO START YOUR UNIT
_ilLWARNING: The trimmer head wilI
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
STARTING ACOLD ENGINE (or a
warm engine after running out of
fuel)
Starting Position
1 Set unit on a flat surface.
2. Stowly pre_s the primer bulb 6times.
3 Move choke lever to the FULL CHOKE
position.
4- Squeeze the throttte trigger fully and hold
through all remaining steps.
Choke
Starter Handle
5 Pull starter rope handle sharply until engine
sounds as ff it is trying to start, but do not
pull rope more than 6 #rues.
6. As soon as engine sounds as ifit is trying to
start, move choke lever to HALF CHOKE
pesition.
7 Pull starter rope sharply until engine runs,
but no more than 6 pulls.
NOTE: if the engine doesn't start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls, if the engine still doesn't
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
8 Once the engine starts, allow itto run 10 se-
conds, then move the choke lever to the
RUN pos_on. Allow the unit to run for 30
more seconds at RUN before releasing the
throttle trigger.
NOTE: If engine dies with the choke Ie-
vet in the RUN position, move the choke
Iever to the HALF CHOKE position and
pull the rope until engine runs, but no
more than 6 pulls.
STARTING A WARM ENGINE
1. Move the choke lever to the HALF CHOKE
position.
2. Squeeze and hold the throttte trigger Keep
throttle trigger fully squeezed until the en-
gine runs smoothly.
3. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
g A_low engine to run 15 seconds, then move
the choke lever to RUN.
NOTE: If engine has not started, pull starter
rope 5 more pulls If engine still does not run, it
is probably flooded.

STARTINGA FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position; then, pu_lthe
rope to clear the engine of excess f_el. This
could require puIling the starter handle many
times depending on how badly the unit is
flooded. If the unit stiil doesnt start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
ALWAYS WEAR: _,_ Eye protection
Longp
Heavy shoes
Cut from your left to your right.
_ WARNING: Alwaysweareye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury
Do not run the engine at a higher speed than
necessary. The cutting line will cut eflielenfly
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line w_lllast bnger and witl
be less likely to "weld" onto the spoel.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
• Release the throttle trigger.
• Push and hold the STOP switch in the
STOP position until the engine stops.
TRIMMER LINE ADVANCE
The trimmer line wil_advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at fu_l throttle.
The most efficient line length is the maximum
length alIowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
To advance Iine:
• Operate the engine at full throttle.
• Hold the trimmer head paraltelto and above
the grassy area.
• Tap the bottom of the trimmer head Iighfly
on the ground one time. Approximately 2
inches (5 cm) of line will be advanced with
each tap.
Always tap the trimmer head on a grassy
area. Tapping oR surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient Iine length.
_WARNING: Use oniy O.O8O" (2mm)
diameter Iine. Other sizes of line will not ad-
vance properly and will result in improper cut-
ting head function or can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous miselle that
can cause serious injury.
CUTTING METHODS
,_fl,WARNING: Use minimumspeed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the Iine, or be thrown causing a
sebous hazard.
• The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Tip of line does Line crowded into
the cutting.
Right W}ong
• The line wi}l easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4-5 inches (10-13 cm) and
use at less than fult throttle
• For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
• During light duty cutting.
• Near objects around which the line can
wrap such as small posts, trees or fence
wire.
• For mowing or sweeping, use full throttle for
a good clean job.
TRtMMING- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle Allow only the tip of the line to
make contact. Do not force trimmer _ine into
work area.

para}le_tothegroundAvoidpressingthe
Trimming headintothegroundasthiscanscalpthe
groundanddamagethetool.
Mowing
3 inches
above ground
SCALPING - The scalping technique re-
moves unwanted vegetationdown to the
ground. Hold the bottom of the trimmer head
about 3 inches (8 cm) above the ground and
at an angle. Allow the tip ofthe line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
Scalping
SWEEPING - The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line para{lel to and above
the surfaces being swept and move the tool
from side to side.
Sweeping
MOWING - Your trimmer is ideaJ for mowing
ill places conventional Iawn mowers cannot
reach. In the mowing position, keep the line
III WAHI_III_ILi: Disconnect the spark
pIug before performing maintenance except
for carburetor adjustments.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Spark Pk_gBoot
• Air Filter
• Housing Screws
• Assist Handle Screws
• Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts
• STOP Switch - Ensure STOP switch func-
tions propedy by pushing and holding the
switch in the STOP position. Make sure en-
gine stops. Restart engine and continue
• Pue} Tank - Discontinue use of unit if fue_
tank shows signs of damage or leaks
• Debris Shietd - Discontinue use of unit if
debris shield is damaged
INSPECT AND CLEAN UNIT AND
LABELS
• After each use, inspect complete unit for
loose or damaged parts. Clean the un_ and
labels using a damp cloth with a mi_d deter-
gent.
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consul_ption and
harmful emissions. Always clean after every
5 hours of operation.
1. CIean the air filter cover and the area
around it to keep dirt from falling into the
carburetor chamber when the cover is
opened.
2 Open air filter cover by pushing button
(see ilIustraben). Remove air filter.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean fi{ter in gasoline or other flammable
solvent.
3 Wash the filter in soap and water.
g. AlIow fiIter to dry.
5. Replace air filter and close cover.
7

Button
Air FiIter
\
Air FiRer Cover
MUFFLER AND SPARK ARREST-
ING SCREEN
,_WARNING: The muffler on this prod-
uct contains chemicals known to the State of
CalTIornia to cause cancel
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen.
For normal homeowner use, however, the
muffler and spark arresting screen will not re-
quire any service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your authorized service dealer
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch (06 mm) Igni-
tion timing is fixed and nonadjustabIe.
1. Twist, then pull off spark plug boot.
2 Remove spark plug from cylinder and dis-
card.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(f9 ram) socket wrench.
g Reinstall the spark plug boot.
LINE REPLACEMENT
1 Remove spool by firmly pulling on tap
button.
2. Clean entire surface of hub and spool
3. Replace with a pre-wound spool or cut two
lengths of 12-1/2 feet of 0.080" (2 ram) di-
ameter WEED EATER brand line
_iWARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
g. Insert ends of the lines about 1/2 inch (f
cm) into the small holes on the inside of
spool
spoo,i/ o'es
Line exit holes Line in Notch
\
Une in Notch
5. Wind the line evenly and tightly onto the
spool Wind in the direction of the arrows
found on the spook
6. Push the lines into the notches, leaving 3
to 5 inches (7 - 12 cm) unwound
7. Insert the lines into the the exit holes in
the hub as shown in the illustration
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into
place.
10. Pullthe lines extending outside of the hub
to release the lines from the notches
REPLACING THE CUTTING HEAD
1. Align hole in the dust cup with the hote in the
side of the gearbox by rotating the dust cup.
2 Insert a small screwdriver into aligned
holes This will keep the shaft from turning
while removing and installing trimmer head.
3 While holding the screwdriver in position,
remove trimmer head by turning clockwise.
g Thread replacement trimmer head onto the
shaft by turning counterclockwise Tighten
until secure.
5 Remove the screwdriver.
CARBURETOR ADJUSTMENT
_IWARNING: Keepothersawaywhen
making idle speed adjustments The trimmer
head wilI be spinning during this procedure.
Wear your protective equipment and observe
nil safety precautions.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
• Engine will not idle when the throttle is re-
leased
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object Hoid
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler

Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs w_thout stal_ing (idle speed too slow).
• Turn idle speed screw clockwise to in-
crease engine speed if engine stalls or dies.
• Turn idle speed screw counterclockwise to
decrease engine speed.
If you require further assistance or are unsure
about performing this procedure, conta_ an
authorized serwce dealer or calI
1-800-554-8723.
Air Filter Cover
_WAHNIN_: Perform the following
steps after each use:
• Allow engine to cool, and secure the ueft
before storing or transporting.
• Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
• Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause iniury.
• Store unit and fuel weft out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more
If your unit is to be stored for aperiod of time:
• Clean the entire unit before lengthy storage.
• Store in a clean dry area.
• Lightly oil external metal surfaces
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TiON section of this manual, see message ]a-
be}ed IMPORTANT regarding the use of ga-
sohol in your engine
Fuel stabilizer is an acceptable alternative in
minimtzlng the formation of fuel gum deposits
during storage. Add stabilizer to the gasefine
in the fuel tank or fuel storage container. Fef-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer
ENGINE
• Remove spark p_ugand pour 1teaspoon of
40:1,2-cycle engine oil (air coefed) through
the spark pIug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
• Replace spark plug with new one of recom-
mended type and heat range.
• Clean air filter
• Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worrl parts.
• At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oi_ratio.
OTHER
• Do not store gasoline from one season to
another.
• Replace your gasefine can ifit starts to rust.

TROUBLESHOOTING TABLE
,,_k WARNING: Always stop unit anddisconnect spark plug before performing al_ofthe
recommended remedies betow except remedies that require operation of the unit.
TROUBLE CAUSE REMEDY
Engine will not 1. Engine flooded 1. See "Starting a Flooded Engine in
start. Operation Section.
2. Fuel tank empty 2. Fill tank with correct fuel mixture.
3. Spark plug not firing. 3. InstalI new spark plug
4. Fuel not reaching 4. Check for dirty fuel filter; replace.
carburetor Check for kinked or split fuel line;
repair or replace.
5 Carburetor requires 5. Contact an authorized service dealer
adjustment.
Engine will 1. Carburetor requires f See "Carburetor Adjustment" in
not idle adjustment. Service and Adjustments Section.
proper_y. 2. Crankshaft seals worn. 2 Contact an authorized service dealer.
3. Compression low. 3 Contact an authorized service dealer.
Engine witl not 1. Air filter dirty t. Clean or replace air filter
accelerate, 2 Spark plug fouled 2 Clean or replace plug
lacks power, and regap.
or dies under 3. Carburetor requires 3 Contact an authorized service dealer.
a load adjustment.
4. Carbon build-up on 4- Contact an authorized service dealer.
muffler outlet screen.
5. Compression low. 5 Contact an authorized service dealer.
Engine 1. Choke partially on 1. Adjust choke.
smokes 2 Fuel mixture incorrect 2. Empty fuel tank and refill with
excessively, correct fuel mixture.
3. Air filter dirty. 3. Clean or replaceair filter.
4-. Carburetor requires 4-. Contact an authorized service dealer
adjustment.
Engine runs f. Fuel mixture incorrect. 1. See "Fueling Engine" in Operation
hot section
2. Spark plug incorrect. 2. Replace with correct spark plug.
3. Carburetor requires 3. Contact an authorized service dealer
adjustment
4-.Carbon build-up on 4. Contact an authorized service dealer
muffler outlet screen
10