Weed Eater XT 200 User manual

XT 200/XT 25
FeatherLitetSeries
Wild ThingtWT21
ENGLISH ESPAÑOL FRANÇAIS
RTrademark
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual del operador y siga todas las advertencias e instruc-
ciones de seguridad. El no hacerlo puede resultar en lesiones graves.
AVERTISSEMENT:
Lire le manuel de l’utilisateur et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Operator’s Manual
Manual del Operador
Manuel de L’utilisateur
530088825 10/30/00
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
UL
R
For Occasional Use Only
Copyright E2000 WCI Outdoor Products, Inc.
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Augusta, GA 30907
Electrolux Home Products
North America
Div. of WCI Outdoor Products, Inc.
Mississauga, Ontario l5T 1K6
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com

2
SAFETY RULES
WARNING: When using gardening
appliances, basic safety precautions should
always be followed to reduce the risk of fire
and serious injury. Read and follow all
instructions.
This power unit can be dangerous! Operator
is responsible for following unit and manual
instructions and warnings. Read entire
Operator’s Manual before using unit! Be
thoroughly familiar with the controls and the
proper use of the unit. Restrict the use of this
unit to persons who read, understand, and
follow unit and manual instructions and
warnings. Never allow children to operate
this unit.
SAFETY INFORMATION
ON THE UNIT
OPERATORS
MANUAL
DANGER: Never use blade, wire or
flailing devices. This unit is designed for line
trimmer use only. Use of any other
accessories or attachments will increase the
risk of injury.
WARNING: Trimmer line throws
objects violently. You and others can be
blinded/injured. Wear safety glasses and leg
protection. Keep body parts clear of rotating
line.
Hazard Zone
Safety glasses or similar eye protection
Boots
50 ft.
(15 m)
Keep children, bystanders, and animals 50
feet (15 meters) away. If approached, stop
unit immediately.
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, contact your
Authorized Service Dealer or call
1--800--554--6723.
OPERATOR SAFETY
SDress properly. Always wear safety
glasses or similar eye protection when
operating, or performing maintenance, on
your unit (safety glasses are available).
Eye protection should meet the
requirements of ANSI Z87.1.
SAlways wear face or dust mask if operation
is dusty.
SAlways wear heavy, long pants, long
sleeves, boots, and gloves. Wearing safety
leg guards is recommended.
SAlways wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
SSecure hair above shoulder length. Secure
or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
SBeing fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
SStay Alert. Do not operate this unit when
you are tired, ill, or under the influence of
alcohol, drugs, or medication. Watch what
you are doing; use common sense.
SWear hearing protection.
SNever start or run inside a closed room or
building. Breathing exhaust fumes can kill.
SKeep handles free of oil and fuel.
UNIT/MAINTENANCE SAFETY
SDisconnect the spark plug before
performing maintenance (except
carburetor adjustments).
SLook for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keep in good
working condition.
SReplace trimmer head parts that are
chipped, cracked, broken, or damaged in
any other way before using the unit.
SMaintain unit according to recommended
procedures. Keep cutting line at proper
length.
SUse only 0.065” (1.6 mm) diameter Weed
Eater!brand line. Never use wire, rope,
string, etc.
SInstall required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and
securely fastened.
SMake sure unit is assembled correctly as
shown in this manual.
SMake carburetor adjustments with lower
end supported to prevent line from
contacting any object.
SKeep others away when making carburetor
adjustments.
SUse only recommended Weed Eater!
accessories and replacement parts.
SHave all maintenance and service not
explained in this manual performed by an
authorized service dealer.
FUEL SAFETY
SMix and pour fuel outdoors.
SKeep away from sparks or flames.
SUse a container approved for fuel.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com

3
SDo not smoke or allow smoking near fuel or
the unit.
SAvoid spilling fuel or oil. Wipe up all fuel
spills.
SMove at least 10 feet (3 meters) away from
fueling site before starting engine.
SStop engine and allow to cool before
removing fuel cap.
SAlways store gasoline in a container
approved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage trimmer head and be thrown
causing serious injury.
SUse only for trimming, mowing, and
sweeping. Do not use for edging, pruning,
or hedge trimming.
SKeep firm footing and balance. Do not
overreach.
SKeep all parts of your body away from
spinning line and muffler. Keep engine
below waist level. A hot muffler can cause
serious burns.
SCutting with the line on left side of the shield
will throw debris away from the operator.
SUse only in daylight or good artificial light.
TRANSPORTING AND STORAGE
SAllow the engine to cool; secure unit before
storing or transporting in vehicle.
SEmpty the fuel tank before storing or
transporting the unit. Use up fuel left in the
carburetor by starting the engine and letting
it run until it stops.
SStore unit and fuel in an area where fuel
vapors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
SStore unit so line limiter blade cannot
accidentally cause injury. Unit can be hung
by the tube.
SStore the unit out of the reach of children.
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, call 1--800--554--6723.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength, change in skin color or
texture, or loss of feeling in the fingers, hands,
or joints, discontinue the use of this tool and
seek medical attention. An anti--vibration
system does not guarantee the avoidance of
these problems. Users who operate power
tools on a continual and regular basis must
monitor closely their physical condition and
the condition of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations
exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your Authorized Service Dealer.
ASSEMBLY
WARNING: Make sure your unit is
properly assembled and all fasteners are
secure.
ADJUST THE HANDLE
SLoosen wing nut on handle.
SRotate handle to upright position and
tighten in a comfortable position between
the trigger and the safety label on the tube.
Tighten handle securely.
ATTACH THE SHIELD
WARNING: The shield must be
properly installed. The shield provides partial
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line.
The line limiter blade (on underside of shield)
is sharp and can cut you.
Assemble your shield (Style A or Style B) as
shown.
STYLE A
SInsert bracket into slot in shield. Tighten
wing nut securely.
Bracket
Shield
Slot
Wing
Nut
STYLE B
SAssemble parts as shown; Tighten wing nut
securely.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com

4
Shield
NOTE: Remove
and use washer and
wing nut from this
bolt for assembling
shield.
Wing Nut
Washer
Line Limiter
Blade
FUEL YOUR UNIT
This engine is certified to operate on
unleaded gasoline. Gasoline must be mixed
with a good quality 2--cycle air--cooled engine
oil designed to be mixed at a ratio of 40:1.
Poulan/Weed Eater brand oil is
recommended. (A 40:1 ratio is obtained by
mixing 3.2 ounces of oil with 1 gallon of
unleaded gasoline). When mixing fuel follow
the instructions printed on the container.
Always read and follow the safety rules under
FUEL SAFETY.
STARTING
HOW TO STOP YOUR UNIT
To stop the engine, push and release the
engine STOP switch. The switch will
automatically return to the ON position. Wait
5 seconds before attempting to restart unit to
allow switch to reset.
HOW TO START YOUR UNIT
Starting Position
Choke lever
Primer Bulb
Trigger
Muffler
WARNING: The trimmer head will
turn while starting the engine. Avoid any
contact with the muffler. A hot muffler can
cause serious burns.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
SSet unit on a flat surface.
SSlowly press the primer bulb 6 times.
SMove choke lever to FULL CHOKE position.
SSqueeze the throttle trigger fully and hold
through all remaining steps.
SPull starter rope handle sharply 6 times.
SMove choke lever to HALF CHOKE position.
SPull starter rope handle no more than 6
pulls, until engine runs.
SAllow engine to run 10 seconds, then move
choke lever to OFF CHOKE position.
STARTING A WARM ENGINE
SMove choke lever to OFF CHOKE position.
SPull starter rope handle until engine runs.
SIf engine does not start in 5 pulls, follow
instructions in STARTING A COLD ENGINE.
USING YOUR UNIT
OPERATING POSITION
Eye
Protection
Long Pants
Heavy Shoes
ALWAYS WEAR:
Cut from your right to your left.
ADVANCING THE CUTTING LINE
Advance line by tapping the bottom of the
cutting head lightly on the ground while
engine is running at full speed. A metal blade
attached to the shield will cut the line to the
proper length.
REPLACING THE LINE
SRemove spool by firmly pulling on tap
button.
SClean entire surface of hub and spool.
SReplace with pre--wound spool, or cut a
length of 18 feet of .065” (1.6 mm) diameter
Weed Eater!brand line. Never use wire,
rope, string, etc., which can break off and
become a dangerous missile.
SInsert one end of line about 1/2 inch (1 cm)
into the small hole on the inside of the spool.
SWind line evenly and tightly onto spool.
Wind in the direction of the arrow on the
spool.
SPush the line into the notch, leaving 3 to 5
inches ( 7 -- 12 cm) unwound.
SInsert the line into the exit hole in the hub as
shown in the illustration.
SAlign the notch with the line exit hole.
SPush spool into hub until it snaps into place.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com

5
SPull the line extending outside of the hub to
release it from the notch.
Small
Hole Spool
Hub
Line exit hole
Line in Notch
SERVICE
We recommend all service and adjustments
not listed in this manual be performed by an
Authorized Service Dealer.
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter caps.
Adjusting the carburetor is a complicated
task. We recommend that you take your unit
to an Authorized Service Dealer. Damage will
occur if you turn the needles beyond the
limiter stops.
IGNITION TIMING
The ignition timing is fixed, non--adjustable.
SPARK PLUG
Replace the spark plug yearly using a
Champion RCJ--8Y plug. Spark plug gap is
0.025 inches.
TROUBLE CAUSE REMEDY
Engine will not
start.
SEngine flooded.
SFuel tank empty.
SSpark plug not firing.
SFuel not reaching carburetor.
SCarburetor requires adjustment.
SSee “Starting.”
SFill tank with correct fuel mixture.
SInstall new spark plug.
SCheck for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
SSee “Carburetor Adjustments.”
Engine will not
idle properly.
SCarburetor requires adjustment.
SThrottle trigger screw too
tight.
SSee “Carburetor Adjustments.”
SLoosen screw.
SAir filter dirty.
SSpark plug fouled.
SCarburetor requires adjustment.
Engine will not
accelerate,
lacks power,
or dies under
a load.
SClean or replace air filter.
SClean or replace spark plug; re-gap.
SSee “Carburetor Adjustments.”
Engine
smokes
excessively.
SFuel mixture incorrect.
SAir filter dirty.
SCarburetor requires adjustment.
SEmpty fuel tank and refill with
correct fuel mixture.
SClean or replace air filter.
SSee “Carburetor Adjustments.”
Line does not
advance or
breaks while
cutting.
SLine improperly routed in head.
SLine improperly wound on
spool.
SLine size incorrect.
SCheck line routing.
SRewind line tightly and evenly.
SUse only 0.065” (1.65 mm) dia. line.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of th
e
recommended remedies below other than remedies that require operation of the unit.
Line welds
onto spool.
Line pulls
back into
head.
SLine size incorrect.
SIncorrect spool.
SLine is being crowded against
material being cut.
SUse only 0.065” (1.65 mm) dia. line.
SReplace with correct spool.
SCut with tip of line fully extended.
SToo little line outside of head.
SLine size incorrect.
SRemove spool and pull 4 inches
(10 cm) of line outside of head.
SUse only 0.065” (1.65 mm) dia. line.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com

6
NEED ASSISTANCE?
Need Assistance?
Call 1--800--554--6723
Need Service Part?
Contact your dealer.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS NORTH
AMERICA, Division of WCI Outdoor
Products, Inc., warrants to the original
purchaser that each new Weed Eater brand
gasoline tool or attachment is free from defects
in material and workmanship and agrees to
repair or replace under this warranty any
defective gasoline product or attachment as
follows from the original date of purchase
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use
of accessories and/or attachments not
specifically recommended by
ELECTROLUX HOME PRODUCTS
NORTH AMERICA for this tool. Additionally ,
this warranty does not cover tune--ups, spark
plugs, filters, starter ropes, starter springs,
cutting line, or rotating head parts that will
wear and require replacement with
reasonable use during the warranty period.
This warranty does not cover predelivery
setup or normal adjustments explained in the
operator ’s manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE
EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION
OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAYNOTAPPLYTOYOU.
ELECTROLUX HOME PRODUCTS
NORTH AMERICA’S policy is to
continuously improve its products.
Therefore, ELECTROLUX HOME
PRODUCTS NORTH AMERICA reserves
the right to change, modify, or discontinue
models, designs, specifications, and
accessories of all products at any time
without notice or obligation to any purchaser.
U.S. EPA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND
OBLIGATIONS: The U. S. Environmental
Protection Agency/Environment Canada and
POULAN/WEED EATER, DIVISION OF WCI
OUTDOOR PRODUCTS are pleased to
explain the emissions control system warranty
on your lawn and garden equipment engine. All
new utility and lawn and garden equipment
engines must be designed, built, and equipped
to meet the stringent anti--smog standards.
POULAN/WEED EATER must warrant the
emission control system on your lawn and
garden equipment engine for the periods of time
listed below provided there has been no abuse,
neglect, or improper maintenance of your lawn
and garden equipment engine. Your emission
control system includes parts such as the
carburetor and the ignition system. Where a
warrantable condition exits, POULAN/WEED
EATER will repair your lawn and garden
equipment engine at no cost to you. Expenses
covered under warranty include diagnosis,
parts and labor. MANUFACTURER’S
WARRANTY COVERAGE: If any emissions
related part on your engine (as listed under
Emissions Control Warranty Parts List) is
defective or a defect in the materials or
workmanship of the engine causes the failure of
such an emission related part, the part will be
repaired or replaced by POULAN/WEED
EATER. OWNER’S WARRANTY
RESPONSIBILITIES: As the lawn and garden
equipment engine owner, you are responsible
for the performance of the required
maintenance listed in your Owner’s Manual.
POULAN/WEED EATER recommends that
you retain all receipts covering maintenance on
your lawn and garden equipment engine, but
POULAN/WEED EATER cannot deny
warranty solely for the lack of receipts or for
your failure to ensure the performance of all
scheduled maintenance. As the lawn and
garden equipment engine owner, you should be
aware that POULAN/WEED EATER may deny
you warranty coverage if your lawn and garden
equipment engine or a part of it has failed due to
abuse, neglect, improper maintenance,
unapproved modifications, or the use of parts
not made or approved by the original equipment
manufacturer. You are responsible for
presenting your lawn and garden equipment
engine to a POULAN/WEED EATER
authorized repair center as soon as a problem
exists. Warranty repairs should be completed in
a reasonable amount of time, not to exceed 30
days. If you have any questions regarding your
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com

7
warranty rights and responsibilities, you should
contact your nearest authorized service center
or call POULAN/WEED EATER at
1--800--554--6723. WARRANTY
COMMENCEMENT DATE: The warranty
period begins on the date the lawn and garden
equipment engine is purchased. LENGTH OF
COVERAGE: This warranty shall be for a
period of two years from the initial date of
purchase. WHAT IS COVERED: REPAIR OR
REPLACEMENT OF PARTS. Repair or
replacement of any warranted part will be
performed at no charge to the owner at an
approved POULAN/WEED EATER servicing
center. If you have any questions regarding your
warranty rights and responsibilities, you should
contact your nearest authorized service center
or call POULAN/WEED EATER at
1--800--554--6723 WARRANTY PERIOD: Any
warranted part which is not scheduled for
replacement as required maintenance, or which
is scheduled only for regular inspection to the
effect of “repair or replace as necessary” shall
be warranted for 2 years. Any warranted part
which is scheduled for replacement as required
maintenance shall be warranted for the period of
time up to the first scheduled replacement point
for that part. DIAGNOSIS: The owner shall not
be charged for diagnostic labor which leads to
the determination that a warranted part is
defective if the diagnostic work is performed at
an approved POULAN/WEED EATER
servicing center. CONSEQUENTIAL
DAMAGES: POULAN/WEED EATER may be
liable for damages to other engine components
caused by the failure of a warranted part still
under warranty. WHAT IS NOT COVERED:All
failures caused by abuse, neglect, or improper
maintenance are not covered. ADD--ON OR
MODIFIED PARTS: The use of add--on or
modified parts can be grounds for disallowing a
warranty claim. POULAN/WEED EATER is not
liable to cover failures of warranted parts
caused by the use of add--on or modified parts.
HOW TO FILE A CLAIM: If you have any
questions regarding your warranty rights and
responsibilities, you should contact your
nearest authorized service center or call
POULAN/WEED EATER at 1--800--554--6723.
WHERE TO GET WARRANTY SERVICE:
Warranty services or repairs shall be provided
at all POULAN/WEED EATER service centers.
call: 1--800--554--6723 MAINTENANCE,
REPLACEMENT AND REPAIR OF
EMISSION RELATED PARTS:Any
POULAN/WEED EATER approved
replacement part used in the performance of
any warranty maintenance or repair on
emission related parts will be provided without
charge to the owner if the part is under warranty.
EMISSION CONTROL WARRANTY PARTS
LIST: Carburetor, Ignition System: Spark Plug
(covered up to maintenance schedule), Ignition
Module. MAINTENANCE STATEMENT: The
owner is responsible for the performance of all
required maintenance as defined in the owner’s
manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
For Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com