WEI-YA HI-09UCS User manual

Parameter Specifications
Input DC 10~15V, 300mAmax standby 50mA.Power Consumption 5.0 Watts max standby 0.6 watts.
Impulse Output Multi pulse (normal “High” level)
Inhibit Input High enable( +3v~+15v)
Signals
Out1~6 Output 1 pulse/coin
Con2 Input/output 4 pin male Extend connect port
Con3 Input/output 09FCS 5 pin male General I/O port
Connector
Con5 Input/output 09UCS 6 pin male General I/O port
User controls 5-ch
dip-switch Sw1, sw2, sw3 for channel or impulse ratio select. Sw4, sw5 for mode and other function select.
Overall Dimension
(HXWXD) HI-09UCS: 102x99x55 mm HI-09FCS: 124.5x120.5x64.5 mm
Speed of acceptable Max. 3 coins/second.
Diameter 18mm~30mm
Position 1.8 2.2 2.6 3
Coin size
(mm) Thickness
Adjust Thickness Range 1.2~2.0 1.2~2.4 1.2~2.8 1.2~3.0
Working temperature 5° ~50°
Weight HI-09UCS: 240g
HI-09FCS: 300g
HI-09UCS / HI-09FCS
NEW
(Drop inserting type) (Front inserting type)
Feature
*Support 8channels (coins)self-programming withoutPC.
*With aninhibit wirefor gameboard.
*With 6ch. Parallel outputfor each channel(coin) control.
*Support onecoin thenmulti pulseoutput (impulseout ratio).
*With narrowor wideimpulse widthselect (100msand 50ms).
*Adjustable 4 kindsof coin thickness.
Specifications:
Operation mode:Before switching onthe dc power,
Set DIP4,DIP 5to the "OFF"position.
Impulse and channelratio table (500)
Record mode:Before switching onthe dc
power, setDIP 4,DIP 5to the "ON"
position.
HUAI I ELECTRONICS CO.,LTD
1
3
5
7
9
2
4
6
8
10
1. GND
2. +12V
3. Output ch5
4. Output ch6
5. Impulse output
6. Inhibit control
7. Output ch1
8. Output ch2
9. Output ch3
10. Output ch4
Accessory
HI-09UCS or HI-09FCS X1
Control board (pcb-09-2) X1
10p Signal cable X1
User manual X1
Screw bag (HI-09FCSonly) X1
5P (09F)or 6P(09U) Signal wire X 1
Installation
Case 1:
Using 10p signalcable connect HI-09UCS/HI-09FCS
to control board(pcb-09-2). Andneed 4 wiresconnect
control board (pcb-09-2)to game board.
The 4 wiresdefine as below:
1. +12V: for dcpower (12 volt).
2. GND: fordc power (ground).
3. IMPULSE: forcredit signal (outputsignal).
4. INHIBIT:control by gameboard for enable
or disable coinselector (input).
Case 2:
Using 5Por 6Psignal wire connectto HI-09UCS/HI-09FCS
another end connectto game boardand meter.
+12V
GND
Impulse
Inhibit
DIP SW"X" means off, "O" meanson
Please make suredirection
The 5Pwire defineas below(HI-09FCS only)
1. +12V
2. Counter (Meter)
3. GND
4. Impulse (Credit)
5. Inhibit
The 6Pwire defineas below(HI-09UCS only)
1. GND
2. +12V
3. +12V
4. Counter (Meter)
5. Impulse (Credit)
6. Inhibit
1
2
3
4
5
6
1
2
3
4
5
Multi coin mode Out
DIP3, DIP2, DIP1 XXX XXO XOX XOO OXX OXO OOX OOO
Impulse out Ratio Impulse out Ratio (bonus)Ratio
Channel 12345678
1 XXX 1/2 1/4 111/2 1/2 1/2 1/4 1
2 XXO 11/2 111111/2 2
3 XOX 50C 11/2 221321+1/2 3
4 XOO 1$ 214225+1 4+1 2+1 4
5 OXX 2$ 42844+1 10+2 5+1 4+2 5
6 OXO 5284NA NA 8+2 5+2 6
7 OOX 8410 10 NA NA 10+2 NA 6
8 OOO 10 510 10 NA NA NA NA 6
(Coin)
DIP SW Function Select Action
XRecord 50ms impulse
DIP Sw4 Coin signal width
(impulse) ORecord 100ms impulse
ONormalDIP Sw5
Blank O->X->O Makes channel data Blank
V2.9 (500)
MULTI-COIN SELECTOR
FOR EURO COIN

HI-09UCS / HI-09FCS TECHNICAL BOOKLET
2.6
2.23
1.8
THICKNESS ADJUSTMENT
If you needto adjust thethickness of coinsto be accepted,
just use asmall slotted screwdriver, plug intothe slot and
rotate to fitthe thickness youwant.
RECORD MODE
If you wantto enter therecord mode, setDIP4, DIP5 ofthe DIP
SWITCH to "ON"positions. Thenturn on thepower.
SELECT OUTPUTPULSE WIDTH
If you wantto appoint thepulse width (50msor 100ms, defaultsetting is 100ms),
you must enterthe "RECORD MODE"first. Thenset DIP4 tothe following position.
1.50ms: DIP4to "OFF"
2.100ms DIP4to "ON"
After appointing thepulse width. Enterthe "MEMORIZE COINS"item to begin
memorizing the coins.
CLEAR RECORD FOR SINGLE CHANNEL
The multi coinselector has 8channels to record. Its8 channels represent itcan
record 8kinds of coinsseparately. Ifyou want toclear achannel, please proceed
as follows:
Turnoff the powerfor thenext operationas soon as stepsA,B,C,D iscomplete.
3.Insert onecoin of thefirst kind, thevalue "1/2" willbe memorized inthe set.Then insert one
coin of thefirst kind again,the new value"1/2" will beadded to theprevious "1/2", hencethe
set outputs "1"pulse. To this analogizes.Insert one coinof the 8thkind, the setoutputs "10" pulses.
4.The pulsesgenerated above-mentioned outputvia "IMPULSE" fromthe control board(pcb-09-2).
Besides, one coinbeing inserted willoutputs "one" pulsevia "output ch"corresponded
to its coinchannel(see Impulse andchannel ratio table).For example: Under"channel 5" with
"ratio list 3".Insert one coinwill result inoutputting 8 pulsesvia "IMPULSE" fromthe control
board, and outputting1 pulse via"output ch5" simultaneously.
If the ratiotable can't meetcustomer requirements, pleasecontact the originalfactory.
MEMORIZE COINS
1.You must enterthe "RECORD MODE"first. Then makesure which channelyou
want to saveby setting DIP1,DIP2, DIP3 tothe appropriate positions.Then insert
10 coins ofthe same currencyand makings. Thecoin selector magnetwill operate
three times toindicate a correctoperation. Then besure to turnthe power offfor
the next operation.
2.If anotherdifferent coins isnecessary to memorize,please repeat theoperation
above- mentioned again.
3.If somechannels of theset were memorizedsome time ago,please clear therecords
for all channelsfirst. HUAI I ELECTRONICS CO.,LTD
RATIOLIST CHOICES
1.Under "OPERATION MODE", theswitch DIP3, DIP2,DIP1 positions areassigned to 8ratio lists.
2.Under "RECORDMODE", the switchDIP3, DIP2, DIP1positions are assignedto 8 coinchannels.
OPERATIONMODE
1.Set DIP4,DIP5 to the"OFF" position whenthe power isoff.
2.Turnon the power, and setthe DIP3, DIP2,DIP1 positions to
correspond the ratiolist you need.
3.Now youcan start usingthe multi coinselector.
THREE OUTPUTINTERFACE
(1) 10p signalcable + controlboard for HI-09FCS/HI-09UCS
(2) 5p signalwire use forHI-09FCS connecting togame board andmeter.
(3) 6p signalwire use forHI-09UCS connecting togame board andmeter.
Steps Channel 1
(Coin 1) Channel 2 (Coin 2) Channel 3 (Coin 3) Channel 4 (Coin 4) Channel 5 (Coin 5) Channel 6 (Coin 6) Channel 7 (Coin 7) Channel 8 (Coin 8)
A 00011 10011 01011 11011 00111 10111 01111 11111
BSwitch on Switch on Switch on Switch on Switch on Switch on Switch on Switch on
C 00010 10010 01010 11010 00110 10110 01110 11110
D00011 10011 01011 11011 00111 10111 01111 11111
OK OK OK OK OK OK OK OK
List 1 List 2 List 3 List 4 List 5 List 6 List 7 List 8
00000 10000 01000 11000 00100 10100 01100 11100
Other
Output
TerminalOperation
Mode Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count Pulse
Output
Count 1 Pulse
Output
Coin 1 1/2 1/4 111/2 1/2 1/2 1/4 Output ch1
Coin 2 11/2 111111/2 Output ch2
Coin 3 11/2 221322/3 Output ch3
Coin 4 21422653Output ch4
Coin 5 4284512 66Output ch5
Coin 6 5284NA NA 10 7Output ch6
Coin 7 8410 10 NA NA 12 NA Output ch6
8kindsofcoins
simultaneously
Coin 8 10 510 10 NA NA NA NA Output ch6
Steps Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8
A00011 10011 01011 11011 00111 10111 01111 11111
BCoin 1
Insert 10 coins Coin 2 Insert 10 coins Coin 3 Insert 10 coins Coin 4 Insert 10 coins Coin 5 Insert 10 coins Coin 6 Insert 10 coins Coin 7 Insert 10 coins Coin 8 Insert 10 coins
C3 clicks 3 clicks 3 clicks 3 clicks 3 clicks 3 clicks 3 clicks 3 clicks
DSwitch off Switch off Switch off Switch off Switch off Switch off Switch off Switch off
(ON) 1
(OFF) 0
1. +12V
2. Counter (Meter)
3. GND
4. Impulse (Credit)
5. Inhibit (Enable)
1
2
3
4
5
1. GND
2. +12V
3. +12V
4. Counter (Meter)
5. Impulse (Credit)
6. Inhibit (Enable)
1
2
3
4
5
6
(1)
(2)
(3)
+12V
GND
Impulse
Inhibit