Well Vision User manual

Installation and Operating Manual
Head Up Display
Model: Vision
Thank you for choosing WELL. Please read carefully the following instructions and keep them within reach.
Preorder NO.: HUD-5-VISION-WL

Functions
1.Alarm Icon: High water temperature / Low voltage
alarm / shift reminder / over speed alarm / Fatigue driving
Engine Error
2.Multi-functions display: RPM / Voltage / driving distance /clock / water temperature / fuel consumption
3.Light sensor:HUD can automatically adjust the brightness according to the environment
4.Mileage unit:TRIP means the driving distance from engine start to off
5.Fuel consumption unit: unit of Average fuel consumption per hundred kilometers / instantaneous fuel
consumption =AVG
6.Speed:digital display the vehicle driving speed
7.Speed unit :KM/H=kilometer/hour, MPH=Mile/hour
3 steps for installation
steps as below

1.find out the OBD interface in vehicle
2.put the HUD on the dashboard
3.hide the OBD cable according to the seam
HUD recommendation place
Entering the menu setting mode
Note:When the HUD datas is different with dashboard datas,please adjust the HUD menu.

1.Please confirm that the HUD has been connected to the car OBD2 interface well and HUD is normally working.
2.Find out the HUD setting wave button
3.Long press in the button to enter into the setting mode, and do it again to save & exit
When in the setting mode, HUD display below
Explanation:There are 14 menu options,once entering into the menu mode,short pressing in the button will enter
into next menu,up or down the button to increase or decrease the default parameter.
Quick Setup

When start the engine, HUD will display, then the user can use the quick setup way to adjust the HUD
Switch the multi functions
Short Push up the button, will only display speed.
Short Push in the button can switch the functions

Quick to do factory reset
When HUD is off, long push in the setting button, and at the same time, plug the USB port to the HUD device
Turn on / off buzzer:
when HUD in normal display, push down the button for 5 seconds to turn off the buzzer, do it again to turn on
buzzer
Menu setting Mode Explanation
How to enter into the menu mode?
When HUD is working,long press in the setting button,Then HUD will show as below:
Menu Parameter table
Menu No.
Functions
Screen display
Explanation
Speed
If HUD display speed value is different
from dashboard, up or down the wave
button to adjust, adjust range(50-150)
RPM
If HUD display RPM value is different
from dashboard, up or down the wave
button to adjust, adjust range(50-150)
Fuel
consumption
If the HUD fuel is different as dashboard,
up or down the wave button to adjust,
adjust range(50-150)
RPM Alarm
When RPM over 5000, HUD will give
alarm, up or down the wave button to
adjust, adjust range(1000-7500)

Shift
reminder
When RPM over 5000, HUD will give
alarm, up or down the wave button to
adjust, adjust range(1000-7500)
Four-stage
speed alarm
0=turn off the four-stage alarm
1 =turn on the four-stage alarm
(60KM/H,80KM/H,100KM/H,120KM/H),s
peed alarm shows up when it reaches to
above four speed
Single-stage
Speed alarm
The default over speed alarm is 150
KM/H, adjust range (30-250)
Display
mode
0=automatic mode: when speed below
80km/h, hud show all information,and
when speed over 80km/h,hud only
display speed)
1= always display all information
2=only display speed
Brightness
adjustment
0=automatic adjustment,
1-11 the brightness will be increased as
the No. added
Speed unit
0=KM/H
1=MPH
Water
temperature
0=water temperature,
1= ℃
2 = ℉
Driving
distance unit
0=KM
1=Mile
Starting
voltage
If this HUD cannot automatically turn
off, adjust it to 13.2, then HUD will auto
off after 3 minutes adjust range (0.0-
15.0)
Factory reset
Set to 1,vertically press the setting
button for 5s, then return to the display
interface

Troubleshooting
1.The screen without any display,and no power
Start the car engine;check if the OBD cable line is tight;please pull down the OBD cables more times to ensure;check
if product power switch turns on. If still no display ,please change another car to test, analyze whether the car OBD
diagnostic interface is good, if it is not good,please repair it and try again.
2.Only shows voltage and be automatic power off after 60 second when the device is with power
this product just available for cars with OBD2 agreement and EU-OBD agreement(European region: after 03 years,
Other region:after 07 years)
This Products donnot support JOBD and OBDI and recommended test for another car.
3.See not clearly when HUD under the sunlight
When HUD is power on,vertical press in the wave button 5 seconds to enter into menu option,short press 8 times to
menu 8, adjust the default from 0 to 11 (11 is the brightest) ,and vertical press 5 seconds to save.
4.Wrong operation lead to crashes or inaccurate datas
Do a reset setting.
When HUD is power on,vertical press in the button for 5 seconds to enter into the menu option,short press several
times to the menu 13,adjust the parameter to 1,vertical press in 5 seconds to save.
5.Inaccurate Speed
a.First check the speed unit is correct or not, the speed unit including KM/H and MPH, menu 9 can adjust the speed
unit
b.When HUD is power on,vertical press the wave button 5 seconds to enter into the menu options, and find menu
0,parameter shows 107,up or down the wave button to increase or decrease the value according to the difference
until it shows correct one.After adjustment, vertical press in 5 seconds to save it.
6.Inaccurate RPM
When HUD is power on,vertical press the wave button 5 seconds to enter into the menu 1, parameter shows 100,up
or down the wave button to increase or decrease the value. After adjustment, vertical press in 5 seconds to save it.
7.Inaccurate fuel consumption
The unit for fuel consumption is L/100KM, HUD display is the single driving fuel consumption, while car display is
Integrated average driving fuel consumption, so it is normal if there are difference.

HUD display three kinds of fuel consumption
a.Idle mode: HUD display Instantaneous fuel consumption per hour (L/H), it means HUD can figure out how much
oil the car will consumed when start engine after one hour
b. Driving mode: HUD display Instantaneous fuel consumption of 100KM
c. Finish driving: HUD display is average fuel consumption of 100KM, when turn off the car, HUD will auto turn off in
10s
When HUD is power on,vertical press the wave button 5 seconds to enter into menu option, find menu 2 ,the
parameter shows 100,up or down to adjust.
8.HUD cannot be automatically power off in cars with Start Stop function or when turn off the car, HUD speed
and RPM is not 0
1. If the car is with Start Stop function, find menu 12, adjust the parameter to 13.2 (when car voltage is less than
13.2V, HUD will turn off automatically in 3 minutes)
2. If HUD turn off during driving, find menu 12, adjust the parameter to 12.6 or 12.8
3. If HUD restart after turn off, find menu 12, adjust the parameter to 13.6
9. How to adjust the clock?
When HUD is in the normal display mode, short press in to find clock, long push up the
button the clock will flash, short push up to adjust the minutes, short press in can adjust the hours, after finish
adjust the clock, long press in 5s to save and exit.

Technical Parameters
1.Environment temperature: - 40 0C—+80 0C
Barometric press: 86-106KPa
Relative humidity:10%-95%
Environment voice:<=60dB
2.Work voltage:11V~18Vdc(12Vdc/200mA)
3.Sleep current:<=30mA
4.Product size: fold 135X68X30 mm, full size:135x68x56mm
5.Projector image size:90x20mm
6.Display way: projector
7.Display channel :LED Display
8.Reflector transmittance: 96%
9. Virtual image distance: 55 mm
10: Left and right angle view: 60°
11. downwards angle view: 15°
Waste electrical and electronic equipment are a special waste category, collection,
storage, transport, treatment and recycling are important because they can avoid
environmental pollution and are harmful to health. Submitting waste electrical and
electronic equipment to special collection centers makes the waste to be recycled
properly and protecting the environment. Do not forget! Each electric appliance
that arrives at the landfill, the field, pollutes the environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
[e-mail], www.vitacom.ro