Wen Power 7000E User manual

MODEL 7000E
390 cc Generator
Item # 56682
Owner’s Manual
Manual del Propietario
Questions? Problems?
Please call our customer help line:
[phone] M-F 8-5 CST
FEATURES
x7000 Surge Watt Output
x5500 Rated Watt Output
xPowerful Enough to Run Essential Appliances During Power Outages
x120 and 240 Volt AC Outputs
xLow Oil Automatic Shutoff
xCircuit Breaker for Overload Protection
x6.5 Gallon Fuel Tank Capacity
xDigital Engine Hour Counter
xElectric Starter
xCigarette Lighter Style 12V DC Outlet
xSpark Arrester
xMeets EPA Emission Standards

i
GENERATOR IDENTIFICATION
For information and questions, please contact the Customer Service Help Line by calling 800-232-
1195. Certain information will be requested by the Customer Service Representative and to facilitate
that, please fill in the information below.
Refer to the illustration below for the location of Serial Number. Record generator information in the
spaces provided below.
DATE OF PURCHASE: ______________________________________________
PURCHASED FROM: ______________________________________________
GENERATOR MODEL NUMBER: ____________________________________
ENGINE SERIAL NUMBER: _________________________________________
ENGINE SERIAL NUMBER
SERVICE RECORD
Record Service Dates:
Date Date Date Date Date Date
Oil Change
Change spark plug
Clean Fuel Tank
Clean Filter Cup
Clean Air Cleaner

ii
TABLE OF CONTENTS
GENERATOR IDENTIFICATION ................................................................................................i
SERVICE RECORD .........................................................................................................................i
INTRODUCTION ............................................................................................................................1
SAFETY INFORMATION..............................................................................................................2
GENERAL SAFETY PROCEDURES...........................................................................................3
IMPORTANT SAFETY INSTRUCTIONS...................................................................................5
PACKAGE CONTENTS .................................................................................................................6
GENERATOR COMPONENTS.....................................................................................................7
ASSEMBLY ......................................................................................................................................8
GENERATOR PREPARATION ..................................................................................................11
Using the Generator for the First Time ........................................................................................11
Step 1 - Fill Oil.........................................................................................................................11
Step 2- Add Gasoline................................................................................................................12
Step 3- Ground the Generator...................................................................................................13
Step 4- Connect the Battery…………………………………………………………………. 14
STARTING THE GENERATOR .................................................................................................15
SUBSEQUENT STARTING OF THE GENERATOR...............................................................17
Step 1- Check the Oil ...............................................................................................................17
Step 2 – Check the Gas Level...................................................................................................17
Step 3- Ground the Generator...................................................................................................18
USING THE GENERATOR .........................................................................................................19
AC Usage......................................................................................................................................19
DC Usage......................................................................................................................................22
STOPPING THE GENERATOR .................................................................................................23
MAINTENANCE / CARE .............................................................................................................24
Cleaning the Generator.................................................................................................................24
Checking the Oil...........................................................................................................................24
Changing/ Adding Oil ..................................................................................................................25
Air Cleaner Maintenance..............................................................................................................26
Fuel Filter Cup Cleaning ..............................................................................................................26
Spark Plug Maintenance...............................................................................................................27
Draining the Fuel Tank.................................................................................................................27
STORAGE / TRANSPORT PROCEDURES ..............................................................................28
SPECIFICATIONS ........................................................................................................................29
TROUBLESHOOTING.................................................................................................................30
EXPLODED VIEW AND PARTS LIST......................................................................................31
WIRING DIAGRAM .....................................................................................................................35
WARRANTY STATEMENT........................................................................................................37

1
INTRODUCTION
Thank You for Purchasing a WEN PowerTM Product.
This manual provides information regarding the safe operation and maintenance of this product.
Every effort has been made to ensure the accuracy of the information in this manual.
WEN Power TM reserves the right to change this product and specifications at any time without
prior notice.
Please keep this manual available to all users during the entire life of the generator.
Special Messages
This manual contains special messages to bring attention to potential safety concerns, generator
damage as well as helpful operating and servicing information. Please read all the information
carefully to avoid injury and machine damage.
Questions? Problems?
In order to answer questions and solve problems in the most efficient and speedy manner,
contact Customer Service at:
[phone] M-F 8-5 CST
NOTICE REGARDING EMISSIONS
Engines that are certified to comply with U.S. EPA emission regulations for SORE (Small Off
Road Equipment), are certified to operate on regular unleaded gasoline, and may include the
following emission control systems: (EM) Engine Modifications and (TWC) Three-Way Catalyst
(if so equipped).

2
SAFETY INFORMATION
Before operating this generator read and observe all warnings, cautions, and instructions on
this sheet, on the generator, and in the Owner’s Manual.
NOTE: The following safety information is not meant to cover all possible conditions and
situations that may occur. Read the entire Owner’s Manual for safety and operating
instructions. Failure to follow instructions and safety information could result in serious
injury or death.
This safety alert symbol is used to identify safety information about hazards that can result in
personal injury.
A signal word (DANGER,WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the potential severity of injury.
In addition, a hazard symbol may be used to represent the type of hazard.
DANGER indicates a hazard, which, if not avoided, will result in death or serious
injury.
WARNING indicates a hazard, which, if not avoided, could result in death or
serious injury.
CAUTION indicates a hazard, which, if not avoided, might result in minor or
moderate injury.
CAUTION, when used without the alert symbol, indicates a situation that could
result in damage to the engine or generator.
SAFETY SYMBOLS AND MEANINGS

3
GENERAL SAFETY PROCEDURES
For any questions regarding the hazard and safety notices listed in this manual or on the
product, please call [phone] M-F 8-5 CST before using the generator.
DANGER: CARBON MONOXIDE. Using a generator indoors CAN KILL
YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison gas you
cannot see or smell. If you can smell the generator exhaust, you are breathing CO.
But even if you cannot smell the exhaust, you could be breathing CO.
xNEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed
areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or
opening windows and doors does NOT supply enough fresh air.
xONLY use a generator outside and far away from windows, doors, and vents. These
openings can pull in generator exhaust.
Even if you use a generator correctly, CO may leak into the home. ALWAYS use a battery-
powered or battery-backup CO alarm in the home.
If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh
air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.
WARNING: The exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects, or other reproductive harm.
WARNING: This generator may emit highly
flammable and explosive gasoline vapors, which can
cause severe burns or even death, if ignited. A nearby open flame can lead to
explosion even if not directly in contact with gasoline.
xDo not operate near open flame.
xDo not smoke near generator.
xAlways operate on a firm, level surface.
xAlways turn generator off before refueling. Allow generator to cool for at least 2
minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.
xDo not overfill fuel tank. Gasoline may expand during operation. Do not fill to the
top of the tank. Allow for expansion.
xAlways check for spilled fuel before operating.
xEmpty fuel tank before storing or transporting the generator.
xBefore transporting, turn fuel valve to off and disconnect spark plug cap.

4
WARNING: This generator produces powerful voltage, which can
result in electrocution.
xALWAYS ground the generator before using it (see the “Ground the Generator”
portion of the “GENERATOR PREPARATION” section).
xGenerator should only be plugged into electrical devices, either directly or with an
extension cord. NEVER connect to a building electrical system without a qualified
electrician. Such connections must comply with local electrical laws and codes.
Failure to comply can create a back-feed, which may result in serious injury or death
to utility workers.
xUse a ground fault circuit interrupter (GFCI) in highly conductive areas such as
metal decking or steel work. GFCIs are available in-line with some extension cords.
xDo not use in rainy conditions.
xDo not touch bare wires or receptacles (outlets).
xDo not allow children or non-qualified persons to operate.
WARNING: This generator produces heat when running. Temperatures
near exhaust can exceed 150º F (65º C).
xDo not touch hot surfaces. Pay attention to warning labels on the generator identifying
hot parts of the machine.
xAllow generator to cool down after use before touching engine or areas of the generator
that become hot during use.
CAUTION: Misuse of this generator can damage it or shorten its life.
xUse generator only for its intended purposes.
xOperate only on dry, level surfaces.
xAllow generator to run for several minutes before connecting electrical devices.
xShut off and disconnect any malfunctioning devices from generator.
xDo not exceed the wattage capacity of the generator by plugging in more electrical devices
than the unit can handle.
xDo not turn on electrical devices until after they are connected to the generator.
xTurn off all connected electrical devices before stopping the generator.
xTurn engine switch to “off” position when the engine is not running.

5
IMPORTANT SAFETY INSTRUCTIONS
xSAVE THESE INSTRUCTIONS – This manual contains important instructions for WEN
Power 7000E generator that should be followed during installation and maintenance of the
generator.
xGenerators vibrate in normal use. During and after the use of the generator, inspect the
generator as well as extension and power supply cords connected to it for damage resulting
from vibration. Have damaged items repaired or replaced as necessary. Do not use plugs or
cords that show signs of damage such as broken or cracked insulation or damaged blades.
xFor power outages, permanently installed stationary generators are better suited for
providing backup power to the home. Even a properly connected portable generator can
become overloaded. This may result in overheating or stressing the generator components,
possibly leading to a generator failure.
xWARNING: When this generator is used to supply a building wiring system:
Generator must be installed by a qualified electrician and connected to a transfer switch as
a separately derived system in accordance with the National Electrical Code, NFPA 70.
The generator shall be connected to a transfer switch that switches all conductors other than
the equipment grounding conductor. The frame of the generator shall be connected to an
approved grounding electrode.
In addition to the previous safety notices, please become familiar with the safety and hazard
markings on the generator.

6
PACKAGE CONTENTS
Your generator comes with the items listed below. Please check to see that all of the following
items are included with your generator.
If there are any damaged or missing items, please call [phone] M-F 8-5 CST for
customer service.
Generator
L14-30 Plug for Connecting 240Volt Electrical Devices
Spark Plug Wrench
Wrenches
Mobility Kit

7
GENERATOR COMPONENTS
Please familiarize yourself with the locations and functions of the various components and controls
of your generator.
.
(1) Fuel Cap- Access to the fuel tank for adding
fuel.
(2) Fuel Gauge- Indicates the amount of fuel in the
tank.
(3) Power Indicator-Green lights that turn on to
indicate the output of power to each receptacle.
(4) Digital Engine hour counter
(5) 240/120 Volt AC Receptacle- To connect
electrical devices that run 120 and/or 240 Volt,
60 Hz, single phase, AC current.
(6) 12V Cigarette lighter Style DC Receptacle
(7) Circuit Reset Buttons- Reset buttons that
protect the generator from electrical overload.
(8) 12V Battery
(9) 10" Never Flat Wheels- For easy transport.
(10) 120 Volt AC Duplex Receptacle- To connect
electrical devices that run 120 Volt, 60 Hz,
single phase, AC current.
(11) Oil Fill and Dipstick- Location for checking and
filling engine oil.
(12) Engine Switch- Used to start/stop engine.
(13) Handles- For easy transport.
(14) Recoil Starter- Pull-cord for starting engine.
(15) Fuel Valve- Allows fuel to enter engine.
(16) Air Cleaner- a removable, cleanable, sponge-like
element that limits the amount of dirt pulled into the
engine.

8
ASSEMBLY
In order to best protect the generator while in the package, this product comes with some
components disassembled. Please complete the following assembly steps before proceeding to use
the generator. For ease of assembly, we recommend attaching the components in the order listed in
this manual.
If after reading this section, you are unsure about how to perform any of the steps, please call
[phone] M-F 8-5 CST for customer service.
WARNING: This generator is heavy. Some assembly procedures may require
lifting equipment or two people.
Attach Feet
To attach the feet to the generator, perform the following steps:
1. Stack the two generator wheels on top of each other. Lift the end of the generator that has
the recoil starter onto the stack of wheels (see figure 1). Be careful not to obstruct any
holes on the generator frame.
2. Place one leg onto the frame as shown in figure 2. Line up the holes on the generator
frame with the holes on the bracket portion of the leg. Tighten using two M6x40 bolts, two
M6 nuts, and the included wrench.
3. Repeat step 2 for the other generator leg.
Figure 1- Stacking the wheels
a b
Figure 2- foot assembly

9
Attach Handles
The handles attach to the generator frame on the same side as the recoil starter (Left side when
facing control panel). To attach the handles to the generator frame, perform the following steps:
1. Take one handle and line up the holes in the handle bracket with the holes on the
generator frame.
2. Slide a bolt through the holes in the handle and generator frame to hold the handle onto
the frame.
3. Secure the bolt in place with a nut.
4. Repeat steps 1-3 for the other handle.
At this point, gently remove the two wheels from underneath the generator.
Figure 3- handle assembly
Attach Wheels
To attach the wheels to the generator, perform the following steps:
1. Find a wood block or similar item that is 3 inches thick or greater and rest the exhaust end
of the generator on the block as shown in figure 4.
2. Take one wheel shaft, and one M12 nut as shown. Slide the wheel shaft, with the threaded
part facing inward, through the frame. Secure using an M12 nut and the included wrench as
shown in figure 5.
3. Slide the wheel onto the axle and secure in place using a large cotter pin as shown in figure
6. Spread the pin legs apart slightly to help secure the pin in place.
4. Repeat steps 2 and 3 for the other wheel.
At this point, the generator assembly is complete. Gently remove the generator from the wood
block.

10
Figure 4- supporting the generator Figure 5- axle assembly
a b
c
CAUTION: Only this side toward AXLE.
Figure 6- wheel installation
a b

11
GENERATOR PREPARATION
Using the Generator for the First Time
The following section describes steps necessary to prepare the generator for use. If after
reading this section, you are unsure about how to perform any of the steps please call (800)
232-1195 M-F 8-5 CST for customer service. Failure to perform these steps properly can
damage the generator or shorten its life.
Step 1 - Fill Oil
The generator is shipped without oil. User must add the proper amount of oil before operating the
generator for the first time. The oil capacity of the engine crankcase is 37 fluid oz.
Select good quality detergent oil bearing the American Petroleum Institute (API) service
classifications SJ, SL, or SM. (Synthetic oils may be used.) Use the SAE viscosity grade
of oil from the following chart that matches the starting temperature anticipated before
the next oil changes.
Figure 7- Engine oil recommendations
To fill oil to the crankcase, follow these steps:
1. Make sure the generator is on a level surface. Tilting the generator to assist in filling will
cause oil to flow into engine areas and will cause damage. Keep generator level!
2. Remove the oil filler/dipstick cap from the engine as shown in figure 8.
3. Using a funnel, add the appropriate type and amount of oil into the crankcase. The
crankcase is full when the oil level has reached the second thread from the lip of the
opening (see figure 9).
4. Check for oil leaks. Reinstall oil filler cap before starting engine.
Figure 8- Unscrewing the oil cap Figure 9- filling oil

12
Step 2- Add Gasoline
WARNING: This generator may emit highly
flammable and explosive gasoline vapors, which can
cause severe burns or even death if ignited. A nearby
open flame can lead to explosion even if not directly in contact with gasoline.
xDo not operate near open flame.
xDo not smoke near generator.
xAlways operate on a firm, level surface.
xAlways turn generator off before refueling. Allow generator to cool for at least 2
minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.
xDo not overfill fuel tank. Gasoline may expand during operation. Do not fill to the
top of the tank. Allow for expansion.
xAlways check for spilled fuel before operating. Clean up any spilled fuel before
starting.
xEmpty fuel tank before storing or transporting the generator.
xBefore transporting, turn fuel valve to off position and disconnect spark plug cap.
Use fresh (within 30 days from purchase), unleaded gasoline with a minimum 87 octane rating. Do
not use gasoline which contains Methanol. Do not mix oil with gasoline.
To add gasoline, follow these steps:
1. Make sure the generator is on a level surface.
2. Unscrew gas cap and set aside (NOTE: the gas cap may be tight and hard to unscrew).
3. Slowly add unleaded gasoline to the fuel tank. Be careful not to overfill. Please refer to the
chart in figure 10 to find the gas capacity of your generator model. The fuel gauge on the
top of the generator indicates how much gasoline is in the generator gas tank. NOTE: Do
not fill the fuel tank to the very top. Gasoline will expand and spill over during use even
with the fuel cap in place.
4. Reinstall fuel cap and wipe off any spilled gasoline with a dry cloth.
IMPORTANT:
xNever use an oil/gasoline mixture.
xNever use old gas.
xAvoid letting dirt or water into the fuel tank.
xGas can age in the tank and make it hard to start up the generator in the future. Never store
generator for extended periods of time with fuel in the tank.
Model number 7000E
Gas tank
capacity
25L (6.5 gallons)
Figure 10- Gas Tank Capacity

13
Step 3- Ground the Generator
WARNING: Failure to properly ground the generator can result in
electrocution.
Ground the generator by tightening the grounding nut against grounding wire (see figure 11). A
generally acceptable grounding wire is a No. 12 AWG (American Wire Gauge) stranded copper
wire. This grounding wire should be connected at the other end to a copper or brass grounding rod
that is driven into the earth. Wire and grounding rod are not included in generator contents.
Grounding codes can vary by location. Please contact a local electrician to check the grounding
regulations for your area.
Figure 11- Grounding nut location

14
Step 4 – Connect the Battery
WARNING:Battery gives off explosive hydrogen gas.
xKeep battery away from spark, flame, or cigarette.
xDo not connect or disconnect battery while generator is running.
xService or use battery only in well ventilated areas.
WARNING:Battery contains sulfuric acid. Battery acid is poisonous. Tilting the
generator with the battery installed can cause battery acid to spill.
xWear protective clothing and eyewear when servicing battery.
xKeep out of reach of children.
xDo not tilt generator with battery installed.
xIf battery acid gets on your skin, wash with water immediately.
xIf battery acid gets in your eyes, flush with water for at least 15 minutes and call a
doctor immediately.
If battery acid is swallowed, drink a large amount of water or milk. Then drink milk of
magnesia or vegetable oil. Call a doctor immediately.
The generator comes with the battery disconnected for safety. To use the electric start, the battery
needs to be connected. To connect the battery:
1. Remove the protective covering from the free end of the negative battery cable. This cable
is connected to the generator on the other end and is located in the vicinity of the battery.
2. Attach the free end of the negative cable to the battery and secure the connection.
NOTE: If you do not plan to use the generator for a long period of time, it is a good idea to
disconnect the negative battery cable from the battery for storage. After disconnecting the cable,
cover the free end with an insulator such as electrical tape.
NOTE: After completing the 4-step Generator Preparation, the generator is ready to be
started.

15
STARTING THE GENERATOR
Before starting the generator, make sure you have read and performed the steps in the
“Generator Preparation” section of this manual. If you are unsure about how to perform any
of the steps in this manual please call [phone] M-F 8-5 CST for customer service.
DANGER: CARBON MONOXIDE. Using a generator indoors CAN KILL
YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison gas you
cannot see or smell. If you can smell the generator exhaust, you are breathing CO.
But even if you cannot smell the exhaust, you could be breathing CO.
xNEVER use a generator inside homes, garages, crawlspaces, or other partly enclosed
areas. Deadly levels of carbon monoxide can build up in these areas. Using a fan or
opening windows and doors does NOT supply enough fresh air.
xONLY use a generator outside and far away from windows, doors, and vents. These
openings can pull in generator exhaust.
Even if you use a generator correctly, CO may leak into the home. ALWAYS use a battery-
powered or battery-backup CO alarm in the home.
If you start to feel sick, dizzy, or weak after the generator has been running, move to fresh
air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.
WARNING: This generator produces powerful voltage, which can result in
electrocution.
xALWAYS ground the generator before using it (see the “Ground the Generator”
portion of the “GENERATOR PREPARATION” section).
xGenerator should only be plugged into electrical devices, either directly or with an
extension cord. NEVER connect to a building electrical system without a qualified
electrician. Such connections must comply with local electrical laws and codes.
Failure to comply can create a back-feed, which may result in serious injury or death
to utility workers.
xUse a ground fault circuit interrupter (GFCI) in highly conductive areas such as
metal decking or steel work. GFCIs are available in-line with some extension cords.
xDo not use in rainy or wet conditions.
xDo not touch bare wires or receptacles (outlets).
xDo not allow children or non-qualified persons to operate.
CAUTION: Disconnect all electrical loads from the generator before
attempting to start.

16
Electric Start
To start the generator using the electric start function, perform the following steps:
1. Make sure no electrical devices are connected to the generator. Such devices can make it
difficult for the engine to start.
2. Check that the generator is properly grounded (see Figure11, “Ground the Generator”).
3. Check the oil and gas levels.
4. Turn the fuel valve to the “ON” position (see figure 12).
5. Move the choke lever to the “Start” position (see figure 13).
6. Set the engine switch to the “ON” position.
7. Press the engine switch to the “START” position for 2-3 seconds or until the engine starts.
NOTE: If the engine does not start after 2-3 seconds, release the switch from the start position.
Keeping the switch in the START position too long can damage the starter.
8. If engine fails to start, wait 10 seconds, then repeat step 7. NOTE: After repeated attempts to
start the engine, please consult the troubleshooting guide before attempting again. If problems
persist please call [phone] M-F 8-5 CST.
9. Once the engine has started. Slowly move the choke lever all the way to the “Run” position.
Allow the generator to run for several minutes before attempting to connect any electrical devices.
Manual Start
To start your generator using the manual start function, perform the following steps:
1. No electrical devices should be connected to the generator during starting. Devices can
make it difficult for the engine to start.
2. Check that the generator is properly grounded (see Figure 11 “Ground the Generator”).
3. Check the oil and fuel levels.
4. Turn the fuel valve to the “ON” position (see figure 12).
5. Move the choke lever to the “START” position (see figure 13).
6. Set the engine switch to the “ON” position.
7. Pull on the recoil starter handle slowly until a slight resistance is felt (see figure 14). Then
pull quickly to start the engine. Return cord gently into the machine. Never allow the cord
to snap back.
8. If engine fails to start, repeat step 7. NOTE: After repeated failed attempts to start the
engine, please consult the troubleshooting guide before attempting again. If problems
persist please call [phone] M-F 8-5 CST.
9. Once the engine has started, slowly return the choke lever all the way to the “RUN”
position.
Allow the generator to run for several minutes before attempting to connect any electrical
devices. This allows the generator to stabilize its speed and temperature.

17
Figure 12- Fuel Valve in the “on” position
Figure 14- Pulling the start cord
Figure 13- Pull choke out for closed position.
Push in for open position.
SUBSEQUENT STARTING OF THE GENERATOR
If this is not the first time using the generator, user should take the following steps to prepare it for
operation.
IMPORTANT: At this point the user should be familiar with the procedures described in the
section titled “Using the Generator for the First Time.” If the user has not yet read this
section, go back and read it now.
Step 1- Check the Oil
Oil consumption is normal during generator usage. The generator is equipped with a low-oil
shutoff to protect it from damage. The oil level in the engine should be checked before each use to
ensure that the engine crankcase contains sufficient lubricant.
To check or add oil, follow these steps:
1. Make sure the generator is on a level surface. Clean around oil fill.
2. Remove the oil filler/dipstick cap and check oil level.
3. If oil level is below the second thread from the lip of the oil fill opening, slowly add oil
until the engine crankcase is filled.
4. Reinstall and tighten oil filler cap before starting the engine. .
Step 2 – Check the Gas Level