Westinghouse WGen12000 User manual

USER MANUAL
WGen12000
Portable Generator
12,000 Running Watts | 15,000 Peak Watts

2 | Westinghouse Outdoor Power Equipment
DISCLAIMERS:
All information, illustrations and specications in this manual are based on the latest information available at the time of
publishing. The illustrations used in this manual are intended as representative reference views only. Moreover, because
of our continuous product improvement policy, we may modify information, illustrations and/or specications to explain
and/or exemplify a product, service or maintenance improvement. We reserve the right to make any change at any time
without notice. Some images may vary depending upon which model is shown.
ALL RIGHTS RESERVED:
No part of this publication may be reproduced or used in any form by any means – graphic, electronic or
mechanical, including photocopying, recording, taping or information storage and retrieval systems – without the
written permission of MWE Investments LLC.
DANGER
This manual contains important instructions for operating this generator. For your safety
and the safety of others, be sure to read this manual thoroughly before operating the
generator. Failure to properly follow all instructions and precautions can cause you and
others to be seriously hurt or killed.
Model
Number
Running
Watts
Peak
Watts
Fuel Tank Size
(L/G)
Rated
Speed
(RPM)
Ignition
Type
Spark
plug
Engine
Disp (cc)
Stroke X
Bore
Oil
Capacity
(L) Oil Type THD
WGen12000 12000 15000 40 L
10.5 G
3600 TCI Bosch
F7TC
713cc 71X80 1.6 L 10W30 <5%
NOTICE
This generator is not equipped with altitude carburetor modication. Even with a carburetor modication, engine horsepower will decrease
about 3.5% for each 300 meter (1,000 foot) increase in altitude. The eect of altitude on horsepower will be greater if no carburetor
modication is made. A decrease in engine horsepower will decrease the power output of the generator. Contact our service team to order
altitude kits.
WGen TECHNICAL SPECIFICATIONS
HAVE QUESTIONS?
Email us at [e-mail]
or call 1-855-944-3571
Operating, servicing and maintaining this equipment can expose you to chemicals including engine exhaust,
carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth
defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your equipment in a well-ventilated area and wear gloves or wash your hands
frequently when servicing your equipment. For more information go to www.P65Warnings.ca.gov.
WARNING

Westinghouse Outdoor Power Equipment | 3
FOR YOUR RECORDS:
Date of Purchase:
Generator Model Number:
Purchased from Store/Dealer:
Generator Serial Number:
IMPORTANT: KEEP YOUR PURCHASE RECEIPT TO ENSURE TROUBLE-FREE WARRANTY
COVERAGE.
PRODUCT REGISTRATION
To ensure trouble-free warranty coverage, it is important you register your Westinghouse generator.
You can register your generator by either:
1. Filling in the product registration form below and mailing to:
Product Registration
MWE Investments LLC
777 Manor Park Drive
Columbus, Ohio 43228
2. Registering your product Online at www.westinghouseportablepower.com/register
To register your generator you will need to locate the following information:
WESTINGHOUSE PRODUCT REGISTRATION FORM
PERSONAL INFORMATION GENERATOR INFORMATION
First Name: _______________________________________ Model Number: _____________________________________
Last Name: _______________________________________ Serial Number:______________________________________
Street Address: ___________________________________ Date Purchased: ____________________________________
Street Address: ___________________________________ Purchased From:____________________________________
City, State, ZIP:____________________________________
Country: __________________________________________
Phone Number: ___________________________________
E-Mail: ___________________________________________
Model info decal located on back side
above muer
Serial Number which is located on
right side of model info decal
SERIAL NUMBER

4 | Westinghouse Outdoor Power Equipment
TABLE OF CONTENTS
WGEN TECHNICAL SPECIFICATIONS ............2
PRODUCT REGISTRATION .....................3
For Your Records: ..........................3
Product Registration .......................3
Product Registration Form ...................3
SAFETY .....................................5
Safety Denitions ..........................5
Safety Symbol Denitions ...................5
General Safety Rules ........................6
UNPACKING .................................7
What Comes in the Box ......................7
ASSEMBLY .................................8
Installing Wheels and Feet ....................8
Installing Lift Bracket ........................8
Installing the Battery ........................9
FEATURES .................................10
Generator Features .........................10
Control Panel Features .....................11
OPERATION .................................12
Before Starting the Generator .................12
High Altitude Operation ......................13
How to Ground Generator ....................13
Connecting the Generator to Building Electrical ...13
System
How to Float the Neutral .....................13
Power Cords .............................14
How to use Lifting Bracket ...................14
Engine Fluids and Fuel .......................15
Adding Gasoline to the Fuel Tank .............15
Power Output and Demand ...................16
Starting the Generator ......................18
Electric Start ..............................18
Remote Start ..............................18
Stopping the Generator ......................19
Normal Operation .........................19
During an Emergency ......................19
MAINTENANCE ..............................20
Maintenance Schedule ......................20
Engine Oil Maintenance .....................21
Engine Oil Specication .....................21
Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 21
Adding Engine Oil .........................21
Changing Engine Oil .......................22
Air Filter Maintenance .......................22
Cleaning the Air Filter .......................22
Spark Plug Maintenance .....................23
VFT Maintenance Reminders ..................23
Checking and Adjusting Valve Lash ..............24
Battery Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Battery Replacement .......................24
Cleaning the Generator ......................25
Cleaning Spark Arrestor ......................25
Storage ..................................25
TROUBLE SHOOTING .........................26
EXPLODED AND ENGINE VIEWS ................28
WGen12000 Exploded View ..................28
WGen12000 Exploded View Part Numbers .......29
WGen12000 Engine View ....................30
WGen12000 Engine View Part Numbers .........31
WGen12000 Schematic ......................33

Westinghouse Outdoor Power Equipment | 5
SAFETY DEFINITIONS
The words DANGER, WARNING, CAUTION and
NOTICE are used throughout this manual to highlight
important information. Be certain that the meanings of
these alerts are known to all who work on or near the
equipment.
This safety alert symbol appears
with most safety statements. It
means attention, become alert, your
safety is involved! Please read and
abide by the message that follows
the safety alerts symbol.
DANGER
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which can cause damage
to the generator, personal property and/or the
environment, or cause the equipment to operate
improperly.
NOTE: Indicates a procedure, practice or condition
that should be followed in order for the
generator to function in the manner
intended.
SAFETY
SAFETY SYMBOL DEFINITIONS
Explosion Hazard
Fire Hazard
Electrical Shock Hazard
Lifting Hazard
Pinch-Point Hazard
Read Manufacturer’s Instructions
Read Safety Messages
Before Proceeding
Wear Personal Protective
Equipment (PPE)
Safety Alert Symbol
Asphyxiation Hazard
Burn Hazard
Burst/Pressure Hazard
Don’t leave tools in the area
Symbol Description

6 | Westinghouse Outdoor Power Equipment
DANGER
Never use the generator in a location that is wet or damp. Never expose the generator to rain, snow, water
spray or standing water while in use. Protect the generator from all hazardous weather conditions. Moisture
or ice can cause a short circuit or other malfunction in the electrical circuit.
Never operate the generator in an enclosed area. Engine exhaust contains carbon monoxide. Only operate
the generator outside and away from windows, doors and vents.
WARNING
Voltage produced by the generator could result in death or serious injury.
• Never operate the generator in rain or a ood plain unless proper precautions are taken to avoid
being subject to rain or a ood.
• Never use worn or damaged extension cords.
• Always have a licensed electrician connect the generator to the utility circuit.
• Never touch an operating generator if the generator is wet or if you have wet hands.
• Never operate the generator in highly conductive areas such as around metal decking or steel works.
• Always use grounded extension cords. Always use three-wire or double-insulated power tools.
• Never touch live terminals or bare wires while the generator is operating.
• Be sure the generator is properly grounded before operating.
WARNING
Gasoline and gasoline vapors are extremely ammable and explosive under certain conditions.
• Always refuel the generator outdoors, in a well-ventilated area.
• Never remove the fuel cap with the engine running.
• Never refuel the generator while the engine is running. Always turn engine o and allow the generator
to cool before refueling.
• Only ll fuel tank with gasoline.
• Keep sparks, open ames or other form of ignition (such as match, cigarette, static electric source)
away when refueling.
• Never overll the fuel tank. Leave room for fuel to expand. Overlling the fuel tank can result in a
sudden overow of gasoline and result in spilled gasoline coming in contact with HOT surfaces.
Spilled fuel can ignite. If fuel is spilled on the generator, wipe up any spills immediately. Dispose of
rag properly. Allow area of spilled fuel to dry before operating the generator.
• Wear eye protection while refueling.
• Never use gasoline as a cleaning agent.
• Store any containers containing gasoline in a well-ventilated area, away from any combustibles or
source of ignition.
• Check for fuel leaks after refueling. Never operate the engine if a fuel leak is discovered.
WARNING
Never operate the generator if powered items overheat, electrical
output drops, there is sparking, ames or smoke coming from the
generator, or if the receptacles are damaged.
Never use the generator to power medical support equipment.
Always remove any tools or other service equipment used during
maintenance from the generator before operating.
NOTICE
Never modify the generator.
Never operate the generator if it
vibrates at high levels, if engine
speed changes greatly or if the
engine misres often.
Always disconnect tools or
appliances from the
generator before starting.
GENERAL SAFETY RULES
SAFETY

Westinghouse Outdoor Power Equipment | 7
CAUTION
Always have assistance when lifting
the generator. The generator is heavy;
lifting it could cause bodily harm.
Avoid cutting on or near staples
to prevent personal injury.
WHAT COMES IN THE BOX (WGEN12000)
Owners Manual
Quick Start Guide/Maintenance Schedule
Wireless Remote Starter (1)
1.6 Liter Bottle of SAE 10W30 Oil (1)
Spark Plug Socket Wrench (1)
Battery Charger
Wheel Kit Accessories Box
Lift bracket with bolts
Pins for handles
Oil funnel (1)
UNPACKING

8 | Westinghouse Outdoor Power Equipment
INSTALLING WHEELS AND FEET
BEFORE ASSEMBLING THE
GENERATOR, REVIEW THE SAFETY
SECTION STARTING ON PAGE 5.
CAUTION
Never lift the generator without
assistance. The generator is heavy
and lifting without assistance could
result in personal injury.
Never use the handles as a lifting point
to support the entire weight of the
generator. Only use the handles to move
the generator by lifting the handles and
using the wheels to move the generator.
Use caution when collapsing the
handles. Hands and ngers could get
caught and pinched.
NOTICE
Assembling the generator will require lifting the unit
on one side. Make sure all engine oil and fuel are
drained from the unit prior to assembling. Once
assembled, the wheel kit is not intended for on-
road use. The wheel kit is designed for use on this
generator only.
INSTALLING WHEELS TO FRAME
1. Insert axle bolt through washer and wheel and slide
hairpin cotter into top of the axle bolt to prevent it
from sliding o the wheel.
Figure 1 - Install Wheels
2. Install the axle bolt and wheel through another
washer and then through the axle bracket on the
frame.
3. Install the hairpin cotter through the end of the axle
bolt to lock it in place.
4. Repeat previous steps on other wheel.
INSTALLING LIFT BRACKET
1. Align the lifting bar with the mounting brackets on the
top of the fuel tank and secure with the 4 M8 ange
bolts provided.
Figure 2 - Install Lift Bracket
ASSEMBLY

Westinghouse Outdoor Power Equipment | 9
1
2
Figure 4 - Connect battery
1 - Positive (+) Battery Cable (Red)
2- Negative (-) Battery Cable (Black)
NOTE: The electric start generator is equipped
with a battery charging feature. Once the engine is
running, a small charge is supplied to the battery
via the battery cables and will slowly recharge the
battery.
INSTALLING THE BATTERY
WARNING
To avoid electrics hock:
• ALWAYS connect the positive (+)
battery cable (red boot) rst when
connecting battery cables.
• ALWAYS disconnect the negative (-)
battery cable (black boot) rst when
disconnecting battery cables.
• NEVER connect the negative (-)
battery cable (black boot) to the
positive (+) post on the battery.
• NEVER connect the positive (+)
battery cable (red boot) to the
negative (-) post on the battery.
• NEVER touch both battery posts
simultaneously.
• NEVER place a metal tool across
both battery posts.
• ALWAYS use insulated or
nonconducting tools when installing
the battery.
1. Remove the two bolts holding on the battery plate.
Tilt the battery forward and remove.
Figure 3 - Remove Battery
2. Connect the positive (+) battery cable (red boot) to
the positive (+) battery post. Make sure boot is over
battery post.
3. Locate negative (-) cable (black boot) and connect
to the negative (-) battery post. Make sure the boot
is over the battery post.
ASSEMBLY

10 | Westinghouse Outdoor Power Equipment
Push Button Electric Start: Starts and stops
the engine.
Fuel Cap: Close until clicking sound is heard.
Control Panel: Contains the circuit breakers
and outlets.
Battery: Included for electric start models.
Oil Fill Plug: Must be removed to add oil.
Oil Drain Plug: Must be removed to drain
engine oil
Oil Dipstick: Used to check correct oil levels.
Never Flat Wheels: For easy portability
Fuel Shut o Valve: Controls the ow of fuel
to the engine.
Lifting Bracket: Bracket to lift generator at
using a crane.
Fuel Gauge: Indicates fuel level.
Spark Plug Boot (Wire): Must be removed
when servicing the engine or the spark plug.
FEATURES
Remote Start Pairing Button: Initiates the remote
key fob pairing function.
Alternator Cover: Gain access to alternator wiring.
CARB Canister: Required for models sold into and
used in California.
Muer and Spark Arrester: Avoid contact until
engine is cooled down. Spark arrestor prevents
sparks from exiting the muer. It must be removed
for servicing.
1
5
6
7
8
10
11
12
13
14
15
9
2
3
4
13
4
6
7
5
11
8
2
10
12
13 15
14
9

Westinghouse Outdoor Power Equipment | 11
ON
OFF
120/240-Volt, 30-Amp Twist Lock Outlet
(NEMA L14-30R): Outlet can supply either
120V or 240V up to 30 amps.
120/240-Volt, 50-Amp Outlet (NEMA 14-50R):
Outlet can supply either 120V or 240V up
to 50 amps.
30-Amp Circuit Breaker: Circuit breaker limits
the current that can be delivered through the 120-
volt duplex outlets to 30amps.
30-Amp Circuit Breaker: Circuit breaker limits
the current that can be delivered through the
120/240-volt duplex outlets to 30amps.
Ground Terminal: The ground terminal is used to
ground the generator.
VFT Data Center: Press and release the mode
button to toggle between Voltage, Frequency,
Total Hour Meter and Run/Maintenance Timer.
Frequency in hertz
Lifetime run hours
Run/Maintenance
Voltage
The Run/Maintenance Timer displays the time
in hours and minutes each time the generator
is ran. The run timer resets to 00:00 when the
generator is shut o. Built into this run timer is a
maintenance reminder. When the new generator
is ran for 25 hours, the meter will display P25.
This is to remind you to change the oil after the
initial 25 hours of run time. When it displays P50,
it is time to clean the air lter. When it displays
P100 it is time change/clean the fuel lter, clean
the air lter, and change the oil.
Push Button Electric Start:
• Push for 1 second to automatically start the
engine.
• Push again to stop the engine.
Engine Control Switch/Battery Disconnect:
Switch to “Stop” to stop the engine. When in
“Stop” position it prevents the unit from drawing
power from the battery. Switch to “Run” before
starting engine.
Battery Charging Port: Charge the battery when
the unit is o with charger provided.
Smart Switch Outlet: Connects the Westinghouse
ST Switch (sold separately) to the control panel.
USB Duplex: Two 5V DC USB ports.
Main Circuit Breaker: The main circuit breaker
controls total output of all outlets to protect the
generator.
120-Volt, 20-Amp Duplex Outlets
(NEMA 5-20R): Each outlet is capable of carrying
a maximum of 20 amps on a single receptacle or a
combination of both receptacles.
20-Amp Circuit Breakers: Each circuit breaker
limits the current that can be delivered through the
120-volt duplex outlets to 20amps.
120-Volt, 30-Amp Twist Lock Outlet
(NEMA L5-30R): Outlet can supply
120V up to 30 amps.
CONTROL PANEL FEATURES
1
8
9
9
8
15
15
10
10
11
12
12
13
13
11
2
2
3
3
4
4
5
6
5
14
14
7
7
FEATURES
16

12 | Westinghouse Outdoor Power Equipment
Weather – Never operate your generator outdoors during
rain, snow or any combination of weather conditions that
could lead to moisture collecting on, in or around the
generator.
Dry Surface – Always operate the generator on a dry
surface free of any moisture.
No Connected Loads – Make sure the generator has no
connected loads before starting it. To ensure there are no
connected loads, unplug any electrical extension cords that
are plugged into the control panel receptacles.
NOTICE
Starting the generator with loads already applied
to it could result in damage to any appliance being
powered o the generator during the brief start-up
period.
Grounding the Generator – The National Electric Code
(NEC), as well as many local electrical codes, may require
the generator to be connected to earth ground before
operating. The most common application that requires
a ground rod is when you are using the generator as a
separately derived system to provide back up power to
your house. Typically this is when a transfer switch has a
switched neutral.
As the generator application has many variables that
cannot be determined by the manufacturer of the
generator, a licensed electrician will need to determine if a
grounding rod is needed.
If a licensed electrician has determine the application
requires a ground rod, make sure it is connected to earth
ground by connecting the ground terminal on the control
panel to earth ground using copper wire (minimum 10
AWG). Consult a qualied electrician for local grounding
requirements.
Neutral Bonded: There is a permanent conduct or between
the generator (stator winding) and the frame.
WARNING
Be sure the generator is properly
connected to earth ground before
operating. The generator must be
grounded to prevent electrical shock
due to faulty appliances.
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR,
REVIEW SAFETY SECTION STARTING
ON PAGE 5.
Location Selection – Before starting the generator,
avoid exhaust and location hazards by verifying:
• You have selected a location to operate the generator
that is outdoors and well ventilated.
• You have selected a location with a level and solid
surface on which to place the generator.
• You have selected a location that is at least 15 feet
(4.5 m) away from any building, other equipment or
combustible material.
• If the generator is located close to a building, make
sure it is not located near any windows, doors and/or
vents.
WARNING
Always operate the generator on a
level surface. Placing the generator
on non level surfaces can cause the
generator to tip over, causing fuel
and oil to spill. Spilled fuel can ignite
if it comes in contact with an ignition
source such as a very hot surface.
NOTICE
Only operate the generator on a solid, level surface.
Operating the generator on a surface with loose
material such as sand or grass clippings can cause
debris to be ingested by the generator that could:
• Block cooling vents
• Block air intake system
OPERATION

Westinghouse Outdoor Power Equipment | 13
HIGH ALTITUDE OPERATION
Engine power is reduced the higher you operate above
sea level. Output will be reduced approximately 3.5% for
every 1000ft of increased altitude from sea level. This is
a natural occurrence and cannot be adjusted by engine.
Increased exhaust emissions can also result due to
increased fuel mixture. Other issues include hard starting,
increased fuel consumption and spark plug fouling.
Contact our service team 1-855-944-3571 for altitude part
kits. High Altitude Carburetor Kit Part Number: 140574
HOW TO GROUND THE GENERATOR
NOTICE
Grounding codes can vary by location. Please
contact a local electrician to check the grounding
regulations for your area.
1. Attach grounding wire to the ground on the control
panel and secure. A generally acceptable grounding
wire is a No. 12 AWG (American Wire Gauge)
stranded copper wire.
2. Connect the other end to a copper or brass
grounding rod that’s driven into the earth.
WARNING
Failure to properly ground the
generator can result in electrocution.
OPERATION
CONNECTING THE GENERATOR TO A
BUILDING ELECTRICAL SYSTEM
It is recommended to use a manual transfer switch when
connecting directly to a buildings electrical system.
Connecting a portable generator to a buildings electrical
system must be made in strict compliance with all national
and local electrical codes and laws, and be completed by a
qualied electrician.
HOW TO FLOAT THE NEUTRAL
The Westinghouse generator is wired with the neutral
bonded to ground. If you are connecting your generator
to a panel board transfer switch, a licensed electrician will
need to consider removing the bonded neutral to ensure
proper operation of household GFCI circuits.
Begin by removing the alternator cover. Once the cover
is o, remove the (white) bonded ground jumper wire
by removing the two nuts that hold it in place. Once the
wire is removed, make sure to reattach the nuts without
removing any other wires that are underneath the jumper
wire. See picture below:
NOTICE
Make sure to keep the white ground jumper wire in case
you need to bond the neutral.
If the bonded neutral is removed the generator must be
relabeled as oating neutral on the control panel.
If your generator is equipped with GFCI receptacles,
removing the bonded neutral may not allow proper
operation of the GFCI receptacles.

14 | Westinghouse Outdoor Power Equipment
LIFTING BRACKET
1. Before lifting the generator, inspect the
bracket and make sure it is securely fastened
to the generator. Do not lift the generator
unless the lifting bracket is securely fastened.
2. Hook a chain or strap through the eye on the
lifting bracket and make sure it is securely
fastened.
3. Connect a suitable lifting device to the chain
or strap. Inspect chain and hook for any
damaged links or any defects that could
cause failure. It is recommended to use hooks
with safety latches installed.
4. Lift the generator slightly to ensure it is
lifting straight and level. Adjust the bracket if
required to allow it to lift correctly.
OPERATION
Do not lift anywhere
else than the eye on
the lifting bracket.
Improper lifting could
damage unit.
POWER CORDS
Using Extension Cords
Westinghouse Portable Power assumes no responsibility for the content within this table. The use of this table is the
responsibility of the user only. This table is intended for reference only. The results produced by using this table are
not guaranteed to be correct or applicable in all situations as the type and construction of cords are highly variable.
Always check with local regulations and a licensed electrician prior to installing or connecting an electrical appliance.

Westinghouse Outdoor Power Equipment | 15
ADDING / CHECKING ENGINE
FLUIDS AND FUEL
BEFORE ADDING/CHECKING ENGINE
FLUIDS AND FUEL, REVIEW SAFETY
SECTION STARTING ON PAGE 5.
DANGER
Filling the fuel tank with gasoline while
the generator is running can cause
gasoline to leak and come in contact
with hot surfaces that can ignite the
gasoline.
Before starting the generator, always check the level of:
• Engine oil
• Gasoline in the fuel tank
Once the generator is started and the engine gets warm,
it is not safe to add gasoline to the fuel tank or engine oil
to the engine while the engine is running or the engine
and muer are hot.
CHECKING AND / OR ADDING ENGINE OIL
WARNING
Internal pressure can build in the engine
crankcase while the engine is running.
Removing the oil ll plug/ dipstick while
the engine is hot can cause extremely
hot oil to spray out of the crankcase and
can severely burn skin. Allow engine
oil to cool for several minutes before
removing the oil ll plug/dipstick.
The unit as shipped does not contain oil in the engine.
You must add engine oil before starting the generator
for the rst time. See Checking Engine Oil and Adding
Engine Oil for instructions on checking engine oil level
and the procedure for adding engine oil.
NOTICE
The engine does not contain engine oil as shipped.
Attempting to start the engine can damage engine
components. The owner of the generator is responsible
to ensure the proper oil level is maintained during the
operation of the generator. Failure to maintain the
proper oil level can result in engine damage.
OPERATION
ADDING GASOLINE TO THE FUEL TANK
WARNING
Never refuel the generator while the
engine is running.
Always turn the engine o and allow
the generator to cool before refueling.
Required Gasoline – Only use gasoline that meets the
following requirements:
• Unleaded gasoline only
• Gasoline with maximum 10% ethanol added
• Gasoline with an 87 octane rating or higher
Filling the Fuel Tank – Follow the steps below to ll the
fuel tank:
1. Shut o the generator.
2. Allow the generator to cool down so all surface areas
of the muer and engine are cool to the touch.
3. Move the generator to a at surface.
4. Clean area around the fuel cap.
5. Remove the fuel cap by rotating counterclockwise.
6. Slowly add gasoline into the fuel tank. Be very careful
not to overll the tank. The gasoline level should NOT
be higher than the ller neck (see Figure 5).
7. Install the fuel cap by rotating clockwise until
you hear a click, indicating the cap is completely
installed.
Figure 5 - Maximum Gasoline Fill Level
CAUTION
Avoid prolonged skin contact with
gasoline. Avoid prolonged breathing of
gasoline vapors.

16 | Westinghouse Outdoor Power Equipment
OPERATION
POWER OUTPUT AND DEMAND
120/240-Volt AC devices have two dierent electric power demands that must be taken
into consideration, namely the running power and the starting/peak power. Both are
measured in Watts (typically abbreviated as “W”).
The steady state continuous load is the running power demand and this is often marked
on the device near its model number or serial number. Sometimes the device might only
be marked with its voltage (i.e. 120 V) and current draw (e.g. 6 Amp or 6 A), in which
case the running power demand in Watts can be obtained by multiplying the voltage
times the current, e.g. 120 V × 6 A = 720 W.
Simple resistive 120-Volt AC devices such as incandescent bulbs, toasters, heaters, etc.
have no extra power demand when starting, and so their starting power demands are
the same as their running power demands.
More complex 120/240-Volt AC devices containing inductive or capacitive elements
such as electric motors have a momentary extra power demand when starting, which
can be up to seven times the running power demand or more. Manufacturers of such
devices rarely publish this starting power demand and so it’s often necessary to
estimate it. A rule of thumb for devices tted with an electric motor is to apply a starting
power multiplier of 1.2 for small hand-held or portable devices and a value of 3.5 for
larger stationary devices. For example, a 900 W angle grinder can be assumed to have a
starting power demand of at least 1.2 × 900 W, which equals 1,080 W. Similarly, a 1,650
W air compressor can be assumed to have a starting power demand of at least 3.5 ×
1,650 W, which equals 5,775 W.
To prevent overloading of the generator’s 120-Volt AC system:
1. Add up the running power demand of all the 120/240-Volt AC devices that will be
connected to the generator at one time. This total must not be greater than the
generator’s specied running power output.
2. Add up the running power demand again, but for the largest motor-driven device
use the value of its starting power demand instead of its running power demand.
This total must not be greater than the generator’s specied starting power output.
3. The total running power demand of all the devices that will be connected to any one
of the generator’s outlets must not exceed the generator’s specied running power
output.

Westinghouse Outdoor Power Equipment | 17
OPERATION
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR,
REVIEW SAFETY SECTION STARTING ON
PAGE 5.
Before attempting to start the generator,
verify the following:
• The engine is lled with engine oil. See Checking
Engine Oil.
• The generator is situated in a proper location. See
Location Selection.
• The generator is on a dry surface. See Weather and
Dry Surface.
• All loads are disconnected from the generator. See No
Connected Loads.
• The generator is properly grounded the Generator. See
Grounding the Generator.
DANGER
Never use the generator in a location
that is wet or damp. Never expose the
generator to rain, snow, water spray or
standing water while in use. Protect
the generator from all hazardous
weather conditions. Moisture or ice
can cause a short circuit or other
malfunction in the electrical circuit.
Never operate the generator in an
enclosed area. Engine exhaust
contains carbon monoxide. Only
operate the generator outside and
away from windows, doors and vents.
NOTICE
The engine is equipped with a low oil shutdown switch.
If the oil level becomes low, the engine may shut down
and not start until the oil is lled to the proper level. Poor
oil quality may interfere with the operation of the low oil
shutdown switch.
The owner of the generator is responsible to ensure the
proper oil level is maintained during the operation of the
generator. Failure to maintain the proper oil level can
result in engine damage.
This generator is equipped with an automatic choke for
starting. This system is always on and cannot be turned
o. Do not attempt to make adjustments to the automatic
choke or any other carburetor adjustments. Tampering
with the automatic choke system may void your warranty.
See an authorized Westinghouse service center for more
information.

18 | Westinghouse Outdoor Power Equipment
STARTING THE GENERATOR
Be sure to check oil levels before starting. If it is the rst
time starting make sure to add oil (see Adding Engine
Oil).
1. Make sure nothing is plugged into power outlets.
2. Verify the battery is properly installed and both
battery cables are attached (see Connecting the
Battery).
3. Make sure the circuit breakers are properly set (see
Figure 6 below).
Figure 6 - Breakers
1
2
3
4
240/120VMain Circuit Breaker Operating Position
240/120V Main Circuit Breaker Tripped Position
120V Circuit Breaker Operating Position
120V Circuit Breaker Tripped Position
4. Move the fuel shut o valve to the ON position (see
Figure 7 below).
Figure 7 - Fuel Shut O - ON
5. Push the engine control switch into the RUN position
(see Figure 8).
Figure 8 - Engine Control Switch - RUN
6. Push and hold the push button start for 1 second,
then release. If using remote start then hold down
START on the remote key fob until the generator
starts, then release (see Figure 9).
ON
OFF
Figure 9 - Push Button Start/Remote Start
• The engine will automatically set the choke and
begin the start sequence.
• If the engine has started successfully the light
indicator on the engine start button will turn green.
• If the engine fails to start, the generator controls
will attempt to start the engine two more times for
a total of three attempts.
• If the third attempt fails, the light on the engine
start button will turn red.
• If the engine has failed to start after three attempts
the push button start can be pushed again to begin
the automatic start sequence.
• The engine control switch can be switched at any
time during the automatic start sequence to abort
the engine start attempt.
NOTE: If the cranking speed drops after each
unsuccessful attempt, then the battery may not
be adequately charged. You can use the charger
provided to charge the battery by plugging it into
the battery charging port on the control panel.
7. Plug in electric devices.
OPERATION

Westinghouse Outdoor Power Equipment | 19
STOPPING THE GENERATOR
Normal Operation
During normal operation, use the following steps to
stop your generator:
1. Remove any connected loads from the control
panel receptacles.
2. Allow the generator to run at “no load” to reduce
and stabilize engine and alternator temperatures.
3. Position the engine control switch to STOP (see
gure 10).
NOTE If you plan to store the generator after
use, turn the fuel shuto valve to the OFF
position and allow the fuel to be consumed from
the carburetor.
4. To stop generator remotely hold the OFF button on
the wireless control (see gure 11). The generator
may run for an additional 5 seconds as it goes
through a cool down cycle before shutting o.
5. Turn the fuel shuto valve to the OFF position.
During an Emergency
If there is an emergency and the generator must be
stopped quickly, position the engine control switch to
the STOP position immediately.
WARNING
Internal pressure can build in the
engine crankcase while the engine
is running. Removing the oil ll plug/
dipstick while the engine is hot can
cause extremely hot oil to spray out
of the crankcase and can severely
burn skin. Allow engine oil to cool for
several minutes before removing the
oil ll plug/dipstick.
Always perform maintenance in a well-
ventilated area. Gasoline fuel and fuel
vapors are extremely ammable and
can ignite under certain conditions.
WARNING
Avoid accidentally starting the
generator during maintenance by
removing the spark plug boot from
the spark plug. For electric start
generators, also disconnect the
battery cables from the battery
(disconnect the black negative (-)
cable rst) and place the cables away
from the battery posts to avoid arcing.
Allow hot components to cool to
the touch prior to performing any
maintenance procedure.
OPERATION
MAINTENANCE
Figure 10 - Engine Control Switch to - STOP
Figure 11 - Remote Stop - Hold Stop Button
BEFORE PERFORMING MAINTENANCE ON THE GENERATOR, REVIEW THE SAFETY SECTION
STARTING ON PAGE 5, AS WELL AS THE FOLLOWING SAFETY MESSAGES.
ON
OFF

20 | Westinghouse Outdoor Power Equipment
MAINTENANCE SCHEDULE
WARNING
Failure to perform periodic maintenance
or not following maintenance
procedures can cause the generator to
malfunction and could result in death or
serious injury.
NOTICE
Periodic maintenance intervals vary depending
on generator operating conditions. Operating the
generator under severe conditions, such as sustained
high-load, high-temperature, or unusually wet or dusty
environments, will require more frequent periodic
maintenance. The intervals listed in the maintenance
schedule should be treated only as a general guideline.
MAINTENANCE
TABLE 1: MAINTENANCE SCHEDULE - OWNER PERFORMED
Maintenance Item
Before Every
Use
After First 20
Hours or First
Month of Use
After 50 Hours
of Use or Every
6 Months
After 100 Hour
of Use or Every
6 Months
After 300 Hours of
Use or Every Year
Engine Oil Check Level Change Change - -
Cooling Features Check/Clean - - - -
Air Filter Check - Clean* - Replace
Spark Arrestor - - - Check/Clean -
Spark Plug - - - Check/Clean Replace
*Service more frequently if operating in dry and dusty conditions
TABLE 2: MAINTENANCE SCHEDULE - AUTHORIZED WESTINGHOUSE
SERVICE DEALER PERFORMED
Maintenance Item
Before Every
Use
After First 20
Hours or First
Month of Use
After 50 Hours
of Use or Every
6 Months
After 100 Hour
of Use or Every
6 Months
After 300 Hours of
Use or Every Year
Valve Clearance - - - - Check/Adjust
Fuel Filter - - - Check/Clean -
Idle Speed - - - - Check/Adjust
CAUTION
Avoid skin contact with engine
oil or gasoline. Prolonged
skin contact with engine oil
or gasoline can be harmful.
Frequent and prolonged contact
with engine oil may cause
skin cancer. Take protective
measures and wear protective
clothing and equipment. Wash
all exposed skin with soap and
water.
Following the maintenance schedule is important
to keep the generator in good operating condition.
The following is a summary of maintenance items by
periodic maintenance intervals.