Westinghouse WH10000DF User manual

USER MANUAL
WH10000DF
Portable Generator
8000 Running Watts | 10000 Peak Watts
7200 Running Watts | 9000 Peak Watts

2 | Westinghouse Outdoor Power Equipment
DISCLAIMERS:
All information, illustrations and specications in this manual are based on the latest information available at
the time of publishing. The illustrations used in this manual are intended as representative reference views only.
Moreover, because of our continuous product improvement policy, we may modify information, illustrations and/or
specications to explain and/or exemplify a product, service or maintenance improvement. We reserve the right
to make any change at any time without notice. Some images may vary depending upon which model is shown.
ALL RIGHTS RESERVED:
No part of this publication may be reproduced or used in any form by any means – graphic, electronic or mechanical,
including photocopying, recording, taping or information storage and retrieval systems – without the written permission
of Westinghouse Outdoor Power Equipment.
DANGER
This manual contains important instructions for operating this generator. For your safety
and the safety of others, be sure to read this manual thoroughly before operating the
generator. Failure to properly follow all instructions and precautions can cause you and
others to be seriously hurt or killed.
NOTICE
Even with a carburetor modication, engine horsepower will decrease about 3.5% for each 300 meter (1,000 foot) increase in altitude. The
eect of altitude on horsepower will be greater if no carburetor modication is made. A decrease in engine horsepower will decrease the
power output of the generator. Weather will aect engine oil performance. Change the type of engine oil used based on weather conditions
to suit the engine needs.
TECHNICAL SPECIFICATIONS
HAVE QUESTIONS?
Email us at [e-mail]
or call 1-855-944-3571
SAVE THESE INSTRUCTIONS
Important safety instructions are included in this manual.
Operating, servicing and maintaining this equipment can expose you to chemicals including engine exhaust,
carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth
defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your equipment in a well-ventilated area and wear gloves or wash your hands
frequently when servicing your equipment. For more information go to www.P65Warnings.ca.gov.
WARNING
Model
Number
Número de modelo
Running
Watts
Vatios de
potencia
nominal
Peak
Watts
Vatios de
potencia pico
Fuel Tank Size
(G/L)
Capacidad del depósito
de combustible (L/G)
Rated Speed
(RPM)
Velocidad nominal
(RPM)
Ignition
Type
Tipo de
encendido
Spark
plug
Bujía
Engine Disp
(cc)
Tamaño del motor (cc)
Stroke
X Bore
Diámetro y
carrera
Oil Capacity
(L)
Capacidad de aceite (L)
Oil
Type
Tipo de
aceite
WH10000DF 8000 Gas
7200 LPG
10000 Gas
9000 LPG
6.6G/25L 3600 TCI F7TC 420 66X90 1.10 10W30

Westinghouse Outdoor Power Equipment | 3
FOR YOUR RECORDS:
Date of Purchase:
Generator Model Number:
Purchased from Store/Dealer:
Generator Serial Number:
IMPORTANT: KEEP YOUR PURCHASE RECEIPT TO ENSURE TROUBLE-FREE WARRANTY
COVERAGE.
PRODUCT REGISTRATION
To ensure trouble-free warranty coverage, it is important you register your Westinghouse generator.
You can register your generator by either:
1. Filling in the product registration form below and mailing to:
Product Registration
Westinghouse Outdoor Power Equipment
777 Manor Park Drive
Columbus, Ohio 43228
2. Registering your product Online at www.westinghouseportablepower.com/register-your-product/
To register your generator you will need to locate the following information:
WESTINGHOUSE PRODUCT REGISTRATION FORM
PERSONAL INFORMATION GENERATOR INFORMATION
First Name: _______________________________________ Model Number: _____________________________________
Last Name: _______________________________________ Serial Number:______________________________________
Street Address: ___________________________________ Date Purchased: ____________________________________
Street Address: ___________________________________ Purchased From:____________________________________
City, State, ZIP:____________________________________
Country: __________________________________________
Phone Number: ___________________________________
E-Mail: ___________________________________________
Made in China/ Fabriqu é en Chine
MWE Investments LLC
Columbus Ohio 43228 USA
Con u à columbus , Ohio,tats-Unis
MWE Investments LLC
Columbus Ohio 43228 Etats-Unis
Par t N 0.
Numéro de
pièc e
Designed in Columbus , Ohio USA
WHERE IS MY SERIAL NUMBER?

4 | Westinghouse Outdoor Power Equipment
TABLE OF CONTENTS
TECHNICAL SPECIFICATIONS ..................2
PRODUCT REGISTRATION .....................3
For Your Records: ..........................3
Product Registration .......................3
Product Registration Form ...................3
SAFETY .....................................5
Safety Denitions ..........................5
Safety Symbol Denitions ...................5
General Safety Rules ........................6
Safety Labels and Decals ....................7
Fuel Safety ................................9
UNPACKING .................................10
What Comes in the Box ......................10
Wheel Kit Accessories Box ...................10
ASSEMBLY .................................11
Installing Wheels and Feet ....................11
Installing the Battery ........................11
FEATURES .................................12
Generator Features .........................12
Control Panel Features .....................14
OPERATION .................................15
Before Starting the Generator .................15
Altitude Kit Part Number .....................15
Power Cord ..............................16
Using Extension Cords ...................16
Using Westinghouse Power Cord ...........16
Transfer Switch Connections ..................17
Engine Fluids and Fuel .......................17
Adding Gasoline to the Fuel Tank ...........18
Connecting to Standard LPG/Propane Tank. . . . 18
Connecting to Large LPG/Propane Tank ......19
Before Starting the Generator .................19
Power Output and Demand ...................20
Starting the Generator on Gas .................21
Starting the Generator on Propane .............22
Stopping the Generator ......................23
Normal Operation .......................23
During an Emergency ....................23
MAINTENANCE ..............................24
Maintenance Schedule ......................21
Maintenance Reminders on VFT Meter ..........25
Cleaning the Spark Arrestor ...................25
Draining the Carburetor Float Bowl .............25
Engine Oil Maintenance .....................26
Engine Oil Specication ...................26
Checking Engine Oil .....................26
Adding Engine Oil .......................26
Changing Engine Oil .....................27
Air Filter Maintenance .......................27
Cleaning the Air Filter ....................27
Spark Plug Maintenance .....................28
Checking and Adjusting Valve Lash. . . . . . . . . . . . . 29
Testing GFCI Outlets ........................29
Battery Replacement .......................29
Cleaning the Generator ......................30
STORAGE ...................................30
TROUBLE SHOOTING .........................31
EXPLODED AND ENGINE VIEWS ................32
WH10000DF Exploded View ..................32
WH10000DF Engine View ....................34
SCHEMATICS ................................36
WH10000DF Schematic .....................36

Westinghouse Outdoor Power Equipment | 5
SAFETY
SAFETY DEFINITIONS
The words DANGER, WARNING, CAUTION and
NOTICE are used throughout this manual to highlight
important information. Be certain that the meanings of
these alerts are known to all who work on or near the
equipment.
This safety alert symbol appears
with most safety statements. It
means attention, become alert, your
safety is involved! Please read and
abide by the message that follows
the safety alerts symbol.
DANGER
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which can cause damage
to the generator, personal property and/or the
environment, or cause the equipment to operate
improperly.
NOTE: Indicates a procedure, practice or condition
that should be followed in order for the
generator to function in the manner
intended.
SAFETY SYMBOL DEFINITIONS
Explosion Hazard
Fire Hazard
Electrical Shock Hazard
Lifting Hazard
Pinch-Point Hazard
Read Manufacturer’s Instructions
Read Safety Messages
Before Proceeding
Wear Personal Protective
Equipment (PPE)
Safety Alert Symbol
Asphyxiation Hazard
Burn Hazard
Burst/Pressure Hazard
Don’t leave tools in the area
Symbol Description

6 | Westinghouse Outdoor Power Equipment
DANGER
Never use the generator in a location that is wet or damp. Never expose the generator to rain,
snow, water spray or standing water while in use. Protect the generator from all hazardous weather
conditions. Moisture or ice can cause a short circuit or other malfunction in the electrical circuit.
Never operate the generator in an enclosed area. Engine exhaust contains carbon monoxide. Only
operate the generator outside and away from windows, doors and vents.
WARNING
Voltage produced by the generator could result in death or serious injury.
• Never operate the generator in rain or a ood plain unless proper precautions are taken to avoid
being subject to rain or a ood.
• Never use worn or damaged extension cords.
• Always have a licensed electrician connect the generator to the utility circuit.
• Never touch an operating generator if the generator is wet or if you have wet hands.
• Never operate the generator in highly conductive areas such as around metal decking or steel
works.
• Always use grounded extension cords. Always use three-wire or double-insulated power tools.
• Never touch live terminals or bare wires while the generator is operating.
• Be sure the generator is properly grounded before operating.
WARNING
Gasoline and gasoline vapors are extremely ammable and explosive under certain conditions.
• Always refuel the generator outdoors, in a well-ventilated area.
• Never remove the fuel cap with the engine running.
• Never refuel the generator while the engine is running. Always turn engine o and allow the
generator to cool before refueling.
• Only ll fuel tank with gasoline.
• Keep sparks, open ames or any other forms of ignition (such as match, cigarette, static electric
source)away when refueling.
• Never overll the fuel tank. Leave room for fuel to expand. Overlling the fuel tank can result in a
sudden overow of gasoline and result in spilled gasoline coming in contact with HOT surfaces.
Spilled fuel can ignite. If fuel is spilled on the generator, wipe up any spills immediately. Dispose
of rag properly. Allow area of spilled fuel to dry before operating the generator.
• Wear eye protection while refueling.
• Never use gasoline as a cleaning agent.
• Store any containers containing gasoline in a well-ventilated area, away from any combustibles or
source of ignition.
• Check for fuel leaks after refueling. Never operate the engine if a fuel leak is discovered.
WARNING
Never operate the generator if powered items overheat,
electrical output drops, there is sparking, ames or smoke
coming from the generator, or if the receptacles are
damaged.
Never use the generator to power medical support
equipment.
Always remove any tools or other service equipment used
during maintenance from the generator before operating.
NOTICE
Never modify the generator.
Never operate the generator if it
vibrates at high levels, if engine
speed changes greatly or if the
engine misres often.
Always disconnect tools or
appliances from the generator
before starting.
GENERAL SAFETY RULES
SAFETY

Westinghouse Outdoor Power Equipment | 7
Made in China/ Fabriqu é en Chine
CSAMaster Contract
Number :
Numéro de contrat
principa l de CSA
MWEInvestments LLC
Columbus Ohio43228 USA
Con u à columbus , Oh io,tats-Unis
MWEInvestments LLC
ColumbusOhio 43228 Etats-Unis
Part N0.
Numéro de
pièce
Designed in Columbus , Ohio USA
SAFETY
SAFETY LABELS AND DECALS
4
1
1
2
Made in China/ Fabriqu é en Chine
MWE Investments LLC
Columbus Ohio 43228 USA
Con u à columbus , Ohio,tats-Unis
MWE Investments LLC
Columbus Ohio 43228 Etats-Unis
Par t N 0.
Numéro de
pièc e
Designed in Columbus , Ohio USA
4
25
3
3
6
4
5
36

8 | Westinghouse Outdoor Power Equipment
SAFETY
SAFETY LABELS AND DECALS
9
8
11
910
7
7
8
4
11
10

Westinghouse Outdoor Power Equipment | 9
When transporting or servicing the generator:
• Make certain the fuel shuto valve is o and the fuel
tank is empty.
• Make sure the LPG tank and LPG hose is not attached
to the generator.
• Disconnect the spark plug wire.
When storing the generator:
• Store away from sparks, open ames, pilot lights, heat
and other sources of ignition.
• Do not store gas or LPG tank near furnaces, water
heaters or any other appliances that produce heat or
have automatic ignitions.
CAUTION
Only use approved LPG tanks with OPD
(overlling prevention device) valve.
Always keep the tank in a vertical position
with the valve on top and installed at
ground level on a at surface. Do not allow
tanks to be around any heat source and
make sure it is not exposed to the sun,
rain and dust. When transporting and
storing, turn o the tank valve and fuel
valve, and disconnect the tank. Make sure
to always cover the generator and tank
outlet with protective plastic caps.
CAUTION
Do not allow children to tamper or
play with the propane tank or hose
connections.
WARNING
If there is a strong smell of propane while
operating the generator close the valve on
the propane tank immediately. Once the
propane is o, use soapy water to check
for leaks on the hose and connections on
the tank valve and the generator. Do not
smoke or light a cigarette or check for
leaks using any open ame source such
as a match or lighter. If a leak is found
contact a qualied technician to inspect
and repair the LPG system before using
the generator.
DANGER
Gasoline and liquid petroleum gas (LPG)
are highly explosive and ammable.
Explosions and re can cause severe
burns or death.
Gasoline and gasoline vapor (Gas)
• Gasoline is highly ammable and explosive.
• Gas expands and contracts with dierent temperatures.
• In case of a gas re, do not attempt to extinguish the
ame if the fuel shuto valve is in the on position.
Introducing an extinguisher to a generator with an open
fuel valve could create an explosion hazard.
• Gas has a distinctive odor, this will help detect potential
leaks quickly.
• Gas vapors can cause a re if ignited.
• Gasoline is a skin irritant and needs to be cleaned up
immediately if it comes in contact with the skin.
Liquid Petroleum Gas (Propane/LPG)
• LPG/Propane is highly ammable and explosive.
• Flammable gas under pressure can cause a re or
explosion if ignited.
• LPG/Propane can settle in low places because it is
heavier than air.
• LPG/Propane has a distinctive odor added to help
detect potential leaks.
• Always keep LPG/Propane tank in an upright position.
• When exchanging LPG/Propane tanks, be sure the tank
value is the same type.
• In case of a LPG/Propane re, do not attempt to
extinguish unless the fuel supply can be shut o.
• LPG/Propane will burn the skin. Prevent skin contact at
all times.
WARNING
Never use a gas container, LPG
connector hose, LPG tank or any other
fuel item that appears to be damaged.
When starting generator:
• Make sure that the gas cap, air lter, spark plug, fuel
lines and exhaust system are properly in place.
• If you spill any gasoline on the tank, allow it to fully
evaporate before operating.
• Make sure the generator and propane tank are on a at
surface before operating.
• If there is a propane odor do not start the unit because
there may be a potential leak.
• Never place propane tank near engine exhaust.
SAFETY
FUEL SAFETY

10 | Westinghouse Outdoor Power Equipment
1. Washer (2 used)
2. Flange Bolt M8 x16mm (4 used)
3. Hairpin Cotter Pin (2 used)
4. Wheel Axle Pin (2)
5. Mounting feet (2)
6. Wheel (2)
CAUTION
Always have assistance when lifting
the generator. The generator is heavy;
lifting it could cause bodily harm.
Avoid cutting on or near staples
to prevent personal injury.
Tools required – box cutter or similar device.
1. Carefully cut the packing tape on top of the carton.
2. Fold back top aps to reveal the manual.
3. Remove the Wheel Kit Accessories cardboard box.
4. Carefully cut two sides of the carton to
remove the generator.
WHAT COMES IN THE BOX
Manual
Quick Start Guide/Maintenance Schedule
1.1 Liter Bottle of SAE 10W30 Oil (1)
LPG Hose (1)
Spark Plug Socket Wrench (1)
Wheel Kit Accessories Box
Funnel (1)
WHEEL KIT ACCESSORIES BOX
Open the Wheel Kit Accessories box and verify the
contents against the list right. If any parts are missing,
please locate an authorized Westinghouse Generator
dealer at [email protected] or call
1-855-944-3571.
UNPACKING
Figure 1 -Wheel and Feet Kit Hardware
LPG hose is shipped under
fuel tank on opposite side
of generator
1
2
3
4
5
6

Westinghouse Outdoor Power Equipment | 11
INSTALLING WHEELS AND FEET
BEFORE ASSEMBLING THE
GENERATOR, REVIEW THE SAFETY
SECTION STARTING ON PAGE 5.
CAUTION
Never lift the generator without
assistance. The generator is heavy
and lifting without assistance could
result in personal injury.
Never use the handles as a lifting point
to support the entire weight of the
generator. Only use the handles to move
the generator by lifting the handles and
using the wheels to move the generator.
Use caution when collapsing the
handles. Hands and ngers could get
caught and pinched.
NOTICE
Assembling the generator will require lifting the unit
on one side. Make sure all engine oil and fuel are
drained from the unit prior to assembling. Once
assembled, the wheel kit is not intended for on-
road use. The wheel kit is designed for use on this
generator only.
INSTALLING FEET TO FRAME
1. Place generator on a at surface.
2. Place a piece of cardboard or other soft material to
tip the generator onto, to protect the frame paint and
prevent the generator from sliding. Tip the generator
onto the side.
3. Install the mounting foot (5) to the frame using M8
ange bolts (2).
2
5
Figure 1 - Assemble Mounting Feet to Frame
INSTALLING WHEELS TO FRAME
1. Insert axle pin (4) through wheel (6) and place washer
(1) between wheel and mounting bracket.
3
16
4
Figure 2 -Wheel Assembly
2. Place hairpin cotter pin (3) through the eye of the wheel
axle pin (4) to secure wheel.
3. Repeat previous steps on other wheel.
INSTALLING THE BATTERY
WARNING
To avoid electric shock:
• ALWAYS connect the positive (+) battery cable
(red boot) rst when connecting battery cables.
• ALWAYS disconnect the negative (-) battery cable
(black boot) rst when disconnecting battery
cables.
• NEVER connect the negative (-) battery cable
(black boot) to the positive (+) post on the battery.
• NEVER connect the positive (+) battery cable (red
boot) to the negative (-) post on the battery.
• NEVER touch both battery posts simultaneously.
• NEVER place a metal tool across both battery
posts.
• ALWAYS use insulated or nonconducting tools
when installing the battery.
1. Verify the positive (+) battery cable (red boot) is securely
tightened to the positive (+) battery post. Make sure
boot is over battery post.
2. Clip the battery quick connects ends together to
connect battery.
Figure 3 -Connect Battery
ASSEMBLY
Mounting
bracket

12 | Westinghouse Outdoor Power Equipment
Fuel Selector Switch: Used to select and turn
on gasoline or propane fuel source.
Electric Start Switch: Hold in Start position
for 1 second to start engine. Make sure to turn
choke on prior to cold starting.
Fuel Cap: Close until clicking sound is heard.
Control Panel: Contains the circuit breakers
and outlets.
Oil Fill Plug/Dipstick: Must be removed to add
and check oil.
FEATURES
Oil Drain Plug: Must be removed to drain engine oil
Never Flat Wheels: For easy portability
Fuel Shut o Valve: Controls the ow of fuel to the
engine.
Manual Choke: Choke must be set manually by
adjusting choke lever.
Single Piece Handle: Includes rubber grip. Allows
you to easily push or pull unit with one hand.
1
5
6
7
8
9
10
2
3
4
12
4
6
5
10
9
8
7
3

Westinghouse Outdoor Power Equipment | 13
Fuel Gauge: Indicates fuel level.
Spark Plug Boot (Wire): Must be removed
when servicing the engine or the spark plug.
Muer and Spark Arrester: Avoid contact
until engine is cooled down. Spark arrestor
prevents sparks from exiting the muer. It must
be removed for servicing.
FEATURES
11
12
13
11
12
13

14 | Westinghouse Outdoor Power Equipment
120-Volt, 20-Amp Duplex GFCI Outlets
(NEMA 5-20R): Each outlet is capable of carrying
a maximum of 20 amps on a single receptacle or
a combination of both receptacles.
20-Amp Circuit Breakers: Each circuit breaker
limits the current that can be delivered through
the 120-volt duplex outlets to 20amps.
25-Amp Circuit Breakers: Each push button
circuit breaker controls total output per leg to
L14-30 receptacle.
120/240-Volt, 30-Amp Twist Lock Outlet
(NEMA L14-30R): Outlet can supply either
120V or 240V output.
Ground Terminal: The ground terminal is used to
ground the generator.
Fuel Selector Switch: Select and turn on gas or
propane.
Electric Start Switch: Hold in Start until engine
starts. Make sure to manually open choke prior to
starting.
Data Center: The VFT Meter is 4 state LED display
that will rotate through volts, frequency, and lifetime
run hours. The 4th display is used for maintenance
reminders and may display as 00:00. You can press
the MODE button to cycle through the dierent
displays. The meter will display volts and hertz
even if there is no load connected.
The frequency and voltage can vary +/- 5% and
still be within tolerance.
Frequency in hertz
Lifetime run hours
Maintenance Reminders
Voltage
CONTROL PANEL FEATURES
1
6
7
8
2
3
4
5
34 6 721
8
FEATURES
5

Westinghouse Outdoor Power Equipment | 15
Weather – Never operate your generator outdoors during rain,
snow or any combination of weather conditions that could
lead to moisture collecting on, in or around the generator.
Dry Surface – Always operate the generator on a dry surface
free of any moisture.
No Connected Loads – Make sure the generator has no
connected loads before starting it. To ensure there are no
connected loads, unplug any electrical extension cords that
are plugged into the control panel receptacles.
NOTICE
Starting the generator with loads already applied to it could result in
damage to any appliance being powered o the generator during the
brief start-up period.
Grounding the Generator – The National Electric Code
(NEC), as well as many local electrical codes, may require
the generator to be connected to earth ground. The most
common application that requires a ground rod is when you
are using the generator as a separately derived system to
provide back up power to your house. Typically this is when a
transfer switch has a switched neutral.
As the generator application has many variables that cannot
be determined by the manufacturer of the generator, a
licensed electrician will need to determine if a grounding rod is
needed.
If a licensed electrician has determine the application requires
a ground rod, make sure it is connected to earth ground by
connecting the ground terminal on the control panel to earth
ground using copper wire (minimum 10 AWG). Consult a
qualied electrician for local grounding requirements.
Neutral Bonded: There is a permanent conduct or between
the generator (stator winding) and the frame.
WARNING
Be sure the generator is properly connected to earth
ground before operating. The generator must be
grounded to prevent electrical shock due to faulty
appliances.
High Altitude Operation
Engine power is reduced the higher you operate above sea
level. Output will be reduced approximately 3.5% for every
1000ft of increased altitude from sea level. This is a natural
occurrence and cannot be adjusted by engine. Increased
exhaust emissions can also result due to increased fuel
mixture. Other issues include hard starting, increased fuel
consumption and spark plug fouling. Contact our service
team 1-855-944-3571 for altitude part kits.
High Altitude Carburetor Kit Part Number: 140571
High Altitude DF Regulator Part Number: 140565
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR,
REVIEW SAFETY SECTION STARTING ON
PAGE 5.
Location Selection – Before starting the generator, avoid
exhaust and location hazards by verifying:
• You have selected a location to operate the generator
that is outdoors and well ventilated.
• You have selected a location with a level and solid
surface on which to place the generator.
• You have selected a location that is at least 15 feet
(4.5 m) away from any building, other equipment or
combustible material.
• If the generator is located close to a building, make
sure it is not located near any windows, doors and/or
vents.
WARNING
Always operate the generator on a level surface.
Placing the generator on non level surfaces can
cause the generator to tip over, causing fuel and
oil to spill. Spilled fuel can ignite if it comes in
contact with an ignition source such as a very hot
surface.
NOTICE
Only operate the generator on a solid, level surface. Operating the
generator on a surface with loose material such as sand or grass
clippings can cause debris to be ingested by the generator that
could:
• Block cooling vents
• Block air intake system
OPERATION

16 | Westinghouse Outdoor Power Equipment
POWERCORD
Using Extension Cords
Westinghouse Outdoor Power Equipment assumes no responsibility for the content within this table. The use of this
table is the responsibility of the user only. This table is intended for reference only. The results produced by using this
table are not guaranteed to be correct or applicable in all situations as the type and construction of cords are highly
variable. Always check with local regulations and a licensed electrician prior to installing or connecting an electrical
appliance.
Using Westinghouse Power Cord
Use the extension cord chart to determine the size
of the conductor for extension cord applications.
Determine the distance of the generator to the
appliance on the top line of the chart. Then select the
rated amperage of the generator on the left side of the
chart. Where the two meet is the size of the conductor
required for the application.
The Westinghouse power cord (shown right) is
connected to the generator at the L14-30R 120/240
plug. The opposite end of the power cord is a fan
tail receptacle with 2 green receptacles and 2 red
receptacles. Each receptacle is rated at 120 volts AC.
To balance the load on the generator’s alternator, use
the red and green identiers on the fan tail receptacle.
To keep the load balanced, connect the loads so that
both color receptacles are used. An example is one in
red and one in green. Do not connect 2 in red and none
in green, or 2 in green and none in red. If only one color
receptacle is used with multiple loads, the alternator
may experience an unbalanced load, causing undue
vibration to generator.
OPERATION
1
2
Figure 4 - Fan Extension Cord
Red Dots
Green Dots

Westinghouse Outdoor Power Equipment | 17
OPERATION
ADDING / CHECKING ENGINE
FLUIDS AND FUEL
BEFORE ADDING/CHECKING ENGINE
FLUIDS AND FUEL, REVIEW SAFETY
SECTION STARTING ON PAGE 5.
DANGER
Filling the fuel tank with gasoline while the
generator is running can cause gasoline to leak
and come in contact with hot surfaces that can
ignite the gasoline.
Before starting the generator, always check the level of:
• Engine oil
• Gasoline in the fuel tank
Once the generator is started and the engine gets warm,
it is not safe to add gasoline to the fuel tank or engine oil
to the engine while the engine is running or the engine
and muer are hot.
CHECKING AND / OR ADDING ENGINE OIL
WARNING
Internal pressure can build in the engine
crankcase while the engine is running. Removing
the oil ll plug/ dipstick while the engine is hot
can cause extremely hot oil to spray out of the
crankcase and can severely burn skin. Allow
engine oil to cool for several minutes before
removing the oil ll plug/dipstick.
The unit as shipped does not contain oil in the engine.
You must add engine oil before starting the generator
for the rst time. See Checking Engine Oil and Adding
Engine Oil for instructions on checking engine oil level
and the procedure for adding engine oil.
NOTICE
The engine does not contain engine oil as shipped.
Attempting to start the engine can damage engine components. The
owner of the generator is responsible to ensure the proper oil level is
maintained during the operation of the generator. Failure to maintain
the proper oil level can result in engine damage.
NOTICE
During the rst ve hours of operating the generator make sure to
not exceed 50% of the rated running watts until the unit is broken
in properly. Make sure to vary to load occasionally to allow stator
windings to heat and cool. Adjusting the load will also help seat
piston rings. Check oil more often during the rst couple times of
operating the generator.
NOTICE
Weather will aect engine oil performance. Change the type of engine
oil used based on weather conditions to suit the engine needs.
CONNECTING THE GENERATOR TO A
BUILDING ELECTRICAL SYSTEM
It is recommended to use a manual transfer switch
when connecting directly to a buildings electrical
system. Connecting a portable generator to a buildings
electrical system must be made in strict compliance
with all national and local electrical codes and laws,
and be completed by a qualied electrician.
TRANSFER SWITCH CONNECTIONS
The Westinghouse generator is wired with the neutral
bonded to ground. If you are connecting your generator
to a panel board transfer switch, a licensed electrician
will need to consider removing the bonded neutral to
ensure proper operation of household GFCI circuits.
Begin by removing the alternator cover. Once the
cover is o remove the nut that holds the bonded
ground jumper wire (see “2” in Figure 5). Once the nut
is removed take the bonded jumper wire o and re-secure
the nut. Next remove the screw holding the neutral ground
wire (see “1” in Figure 5). Attach the bonded jumper wire
(2) to the neutral ground (1) and tighten the screw.
If the bonded neutral is removed the generator must be
relabeled as oating neutral on the control panel.
If your generator is equipped with GFCI receptacles,
removing the bonded neutral may not allow proper
operation of the GFCI receptacles. Always keep the
jumper wire in case it is needed for future use when not
connected to a transfer switch.
1
11
2
2
2
Figure 5
REMOVE
MOVE WIRE HERE
Alternator Neutral Ground Wire (white/Green)
Alternator Bonded Jumper Wire (white/Green)

18 | Westinghouse Outdoor Power Equipment
ADDING GASOLINE TO THE FUEL TANK
BEFORE ADDING GAS TO THE TANK
PLEASE REVIEW FUEL SAFETY
SECTION ON PAGE 9
WARNING
Never refuel the generator while the engine is
running.
Always turn the engine o and allow
the generator to cool before refueling.
Required Gasoline – Only use gasoline that meets the
following requirements:
• Unleaded gasoline only
• Gasoline with maximum 10% ethanol added
• Gasoline with an 87 octane rating or higher
Filling the Fuel Tank – Follow the steps below to ll the
fuel tank:
1. Shut o the generator.
2. Allow the generator to cool down so all surface
areas of the muer and engine are cool to the
touch.
3. Move the generator to a at surface.
4. Clean area around the fuel cap.
5. Remove the fuel cap by rotating counterclockwise.
6. Slowly add gasoline into the fuel tank. Be very
careful not to overll the tank. The gasoline level
should NOT be higher than the ller neck (see
Figure 7).
7. Install the fuel cap by rotating clockwise until
you hear a click, indicating the cap is completely
installed.
Figure 6 - Maximum Gasoline Fill Level
CAUTION
Avoid prolonged breathing of gasoline vapors.
OPERATION
CONNECTING TO STANDARD LPG/PROPANE TANK
BEFORE CONNECTING PROPANE TANK TO
THE GENERATOR PLEASE REVIEW FUEL
SAFETY SECTION ON PAGE 9
Connecting LPG Tank
1. Make sure the generator is o, on a at surface in well
ventilated area.
2. Make sure propane tank valve is in the o position.
3. Make sure the fuel selector switch on the generator
control panel is pointing downward to “Propane”.
4. Remove the plastic cover on the generator propane
inlet valve.
5. Using your ngers tighten the LPG hose (included) end
below to the generator propane inlet. DO NOT OVER-
TIGHTEN 35-88 Ib-in maximum.
6. Attach the other end of the hose to a tank of LPG/
Propane and hand tighten.
7. Check all connections for leaks by wetting the ttings
with soapy water. Anywhere that bubbles appear or
grow indicates a leak in the connection. If a leak exists
at a tting then turn o the tank valve and tighten the
tting. Turn the gas back on and recheck with soapy
water again. If the leak continues or if the leak is not
at a tting then do not use the generator and contact
customer service.
NOTICE
• When using standard 20 or 30 pound capacity LPG tanks, make sure
they have Type 1, right hand Acme threads.
• Verify the requalication date on the tank has not expired.
• All new tanks must be purged of air and moisture prior to lling. Used
tanks that have not been plugged or kept closed must also be purged
• The purging process should be done by a LPG supplier. (Tanks from
an exchange supplier should have been purged and lled properly
already)
• Always position the tank so the connection between the valve and the
gas inlet won’t cause sharp bends or kinks in the hose.
WARNING
Do not start generator if you smell propane. This may
result in explosion hazard. Do not use provided LPG
hose for any other appliances. Always turn o the
propane tank and disconnect LPG hose when not in
use.

Westinghouse Outdoor Power Equipment | 19
NOTICE
The engine is equipped with a low oil shutdown
switch. If the oil level becomes low, the engine may
shut down and not start until the oil is lled to the
proper level. Poor oil quality may interfere with the
operation of the low oil shutdown switch.
The owner of the generator is responsible to ensure
the proper oil level is maintained during the operation
of the generator. Failure to maintain the proper oil
level can result in engine damage.
NOTICE
When operating on LPG it is common for frost to form
on the tank and regulators. This is not an indication
of a problem. The amount of frost that forms can
be aected by the size of the container, the amount
of fuel being used, the humidity of the air and other
operating conditions. In standard use this frost may
reduce ow of gas and lower performance. If frost
becomes an issue try exchanging fuel tanks to allow
the rst tank to warm up. You can also temporarily
warm the tank up by pouring warm water over the top
of the propane tank.
SWITCHING FUEL SOURCES
If you are switching fuel sources make sure to shut the
generator down rst and follow instructions on starting
with your desired fuel source.
NOTICE
If you do not plan on operating the unit on propane
do not leave the propane tank valve open.
When starting on propane the engine may run rough
for a few seconds while it purges gasoline in the
carburetor.
OPERATION
CONNECTING TO LARGE LPG/PROPANE TANK
BEFORE CONNECTING PROPANE TANK TO
THE GENERATOR PLEASE REVIEW FUEL
SAFETY SECTION ON PAGE 9
You can hook up you Duel Fuel Generator to a large home
LP tank. It is required that you consult a plumber to properly
connect your generator to the tank.
To properly connect with a large propane tank you must rst
check and conrm the LP fuel pressure at the outlet of the
LP tank. The LP fuel pressure should be 14-10” of water
column, which is the standard fuel pressure for residential
gas red appliances.
If the LP fuel pressure is within the 14-10” water column
range, the primary fuel regulator should be removed from
the fuel line components. Then plumb directly from the LP
tank to the secondary regulator assembled to the generator.
WARNING
You must consult a certied plumber to connect
to large LP tank safely.
BEFORE STARTING THE GENERATOR
BEFORE STARTING THE GENERATOR,
REVIEW SAFETY SECTION STARTING ON
PAGE 5.
Before attempting to start the generator,
verify the following:
• The engine is lled with engine oil.
• The generator is situated in a proper location.
• The generator is on a dry surface.
• All loads are disconnected from the generator.
• The generator is properly grounded.
• Propane connection is secure with no leaks or damage.
DANGER
Never use the generator in a location that is wet or
damp. Never expose the generator to rain, snow,
water spray or standing water while in use. Protect
the generator from all hazardous weather conditions.
Moisture or ice can cause a short circuit or other
malfunction in the electrical circuit.
Never operate the generator in an enclosed area.
Engine exhaust contains carbon monoxide. Only
operate the generator outside and away from
windows, doors and vents.

20 | Westinghouse Outdoor Power Equipment
OPERATION
POWER OUTPUT AND DEMAND
120-Volt AC devices have two dierent electric power demands that must be taken into
consideration, namely the running power and the starting/peak power. Both are measured in
Watts (typically abbreviated as “W”).
The steady state continuous load is the running power demand and this is often marked on the
device near its model number or serial number. Sometimes the device might only be marked with its
voltage (i.e. 120 V) and current draw (e.g. 6 Amp or 6 A), in which case the running power demand in
Watts can be obtained by multiplying the voltage times the current, e.g. 120 V × 20 A = 2,400 W.
Simple resistive 120-Volt AC devices such as incandescent bulbs, toasters, heaters, etc. have no
extra power demand when starting, and so their starting power demands are the same as their
running power demands.
More complex 120-Volt AC devices containing inductive or capacitive elements such as electric
motors have a momentary extra power demand when starting, which can be up to seven times the
running power demand or more. Manufacturers of such devices rarely publish this starting power
demand and so it’s often necessary to estimate it. A rule of thumb for devices tted with an electric
motor is to apply a starting power multiplier of 1.2 for small hand-held or portable devices and a
value of 3.5 for larger stationary devices. For example, a 900 W angle grinder can be assumed to
have a starting power demand of at least 1.2 × 900 W, which equals 1,080 W. Similarly, a 1,650 W
air compressor can be assumed to have a starting power demand of at least 3.5 × 1,650 W, which
equals 5,775 W.
To prevent overloading of the generator’s 120-Volt AC system:
1. Add up the running power demand of all the 120-Volt AC devices that will be connected to the
generator at one time. This total must not be greater than the generator’s specied running power
output.
2. Add up the running power demand again, but for the largest motor-driven device use the value
of its starting power demand instead of its running power demand. This total must not be greater
than the generator’s specied starting power output.
3. The total running power demand of all the devices that will be connected to any one of the
generator’s outlets must not exceed the generator’s specied running power output or 3,700 W,
whichever is the lesser.