Westinghouse AR400FW Manual

INSTRUCTION GUIDE
AR400FW
Suits the Westinghouse Canopy Rangehood WRC604
RANGEHOOD FLUE EXTENSION

INSTRUCTIONS
In order to correctly install your appliance please refer
to the user manual supplied with your rangehood for full
details or download the user manual by scanning the
below QR code.
To install your flue cover extension, please follow steps 1-8
below (as per the user manual).
Upon completion of step 8, please follow step 9a and 9b
below to replace the upper flue cover which is included
with your rangehood, with this accessory flue cover
extension.
You will need to replace the upper flue cover which is
included with your rangehood, with this accessory flue
cover extension.
NOTE: The flue cover extension MUST be used in
conjunction with the lower flue cover.
Scan the QR code below to download the full
WRC604 rangehood user manual:
Installation
1. Using a spirit level mark a vertical centre line on
the wall where the hood is to be positioned, and a
horizontal line at the hood base position.
NOTE: The height of the underside of the hood
body must be a minimum of 600mm* to a maximum
height of 800mm.
*If the instructions of the hob specify a greater
distance than the minimum above, then that shall be
the minimum height for installation.
2. Mark the location for the flue cover wall mounting
brackets and rangehood mounting points and anti-tilt
fixing points above the hood base using the hood
base as a reference point.
WARNING
WARNING
Failure to install the screws or fixing device in accordance
with these instructions may result in electrical hazards.
Top mounting
bracket for T-piece
(optional part)
Bottom mounting
bracket for flue
cover (required
where ceiling
cornice is in place)
Rangehood
mounting
points
Anti-tilt
fixing
points
Electric
Gas Fig. 5
350
Min 600mm
Max 800mm
Min 650mm
Max 800mm
192
130 140
30
273
55
3. Install flue cover wall mounting brackets with
suitable fasteners. Suitable fasteners must be used
for rangehood mounting points. Refer to Fig.5 for
dimensions. If installation is for recirculation mode
refer to Item 6a and Fig.9.
Fig.6

4. Fit the dampers to the exhaust air outlet. Slight
bending of the dampers will be required for the
fitment.
Fig. 7
5. Hang the body hood on the mounting screws then
secure at the anti-tilt locations(2 places) as indicated
in Fig 8.
Fig.8
Depending on the preferred installation/ducting mode,
follow step 6a or 6b below.
6a. Recirculating mode (Fig.9)
Fix the T-piece to the top mounting bracket by using
the 4 screws supplied as dimension indicated Fig 5.
Adhere two sponge to the outlet of T-piece.
Using the centre line, install the recirculating T-piece
and mounting bracket to the wall.
Install flexible pipe between T- piece and air outlet
Use cable ties or suitable duct tape to secure flexible
pipe to T-piece and outlet of the hood.(Fig.10)
NOTE: When installed in recirculating mode, it is
recommended to use a charcoal filter to prevent odours
being emitted back into the room.
For instructions on fitting charcoal filter, please refer to
page 11 of user manual.
Replacement Charcoal filter part number 09070400082.
Fig.9
T-piece mounting bracket
Flue cover mounting bracket
Flue cover
mounting
bracket
Fig. 10
T-piece mounting
bracket
6b. Ducted mode (Fig.11)
Insert flexible pipe and secure flue tape to air outlet
with suitable duct tape.
NOTE: For ducted mode we recommended to
extend the flue pipe through the roof cladding(with
appropriate flashing) to an external roof cowl, venting
the exhaust externally.
To ensure optimum performance of the rangehood,
the use of bends should be avoided. Straight, rigid
and short ducting is recommended to use. All ducting
must be fire retardant.

and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license by Electrolux Home Products Pty Ltd. All Rights Reserved.
© 2020 Electrolux Home Products Pty Ltd. ABN 51 004 762 341. W_INS_AR400FW_Nov20
WARNING
WARNING
Exhaust air must not be discharged into a wall cavity,
unless the cavity is designed for the purpose.
Fig. 11
7. Insert the power cord to the power outlet.
Fig. 12
8. Insert the flue cover section to the body hood.
Fig. 13
Installing the Flue Cover Extension (Accessory)
9a. Separate the upper and lower flue covers by sliding
the upper cover out of the lower cover.
Upper flue cover
Lower flue cover
9b Discard upper flue cover and replace with new
extension piece as per diagram below.
10. Install the filters to the hood.
Fig. 15
Contact us if you need more help
Australia
telephone: 13 13 49
email: [e-mail]
web: westinghouse.com.au
New Zealand
telephone: [phone]
email: [e-mail]
web: westinghouse.co.nz