Westinghouse QR049 User manual

# QR049
OWNER’S MANUAL
MANUAL DEL USARIO
UNDER CABINET RANGE HOOD
CAMPAÑA EXTRACTORA PARA
INSTALACIÓN BAJO CABINETE

2
ENGLISH
Table of Contents
Table of Contents ............................2
Safety Information............................2
Warranty
One Year Limited Warranty...........................4
Warranty Claim Procedure...........................4
Pre-Installation
Tools/Materials Required ............................5
Package Contents .................................6
Hardware Included.................................6
Planning Installation ...............................7
Installation................................ 10
Operation................................. 13
Maintenance
Replacing Filters .................................14
Replacing Lights .................................14
Care and Cleaning
Range Hood .....................................15
Filters..........................................15
Troubleshooting ............................ 16
Specifications
Wiring Diagram ..................................17
External Range Hood Diagram.......................18
Service Parts .............................. 19
Safety Information
READ AND SAVE THESE INSTRUCTIONS
Warning - To reduce the risk of fire, electric shock, or injury to
persons, observe the following:
1. Use this unit only in the manner intended by the manufacturer. If
you have any questions, contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service
panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by qualied
person(s) in accordance with all applicable codes and standards,
including re-rated construction.
4. Sufcient air is needed for proper combustion and exhausting
of gases through the ue (chimney) of fuel burning equipment
to prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into a wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
DANGER: Turn off the power circuit breaker or the power
switch on the junction box before installing or servicing
this unit. Touching circuitry inside the range hood while it is
energized will result in death or serious injury.
DANGER: All electrical wiring must be properly installed,
insulated, and grounded. Improper insulation and grounding
will result in deadly electrical shock.
DANGER: If installing this unit over a gas range, turn off
the gas at the source before installing or servicing this unit.
WARNING: Attempting to install or service this unit
when you do not have the necessary technical or electrical
background could result in personal injury.
WARNING: The unit has sharp edges. Always wear safety
gloves during installation, cleaning, or servicing.
WARNING: Always leave safety grills and lters in place.
Without these components, operating fans could catch on to
hair, ngers, or loose clothing.
WARNING: Stay clear of the rotating fan when the motor
is running.
WARNING: Keep this appliance clean and free of grease
and residue build-up at all times to prevent res.
CAUTION: This device is for general ventilating use only.
Do not use to exhaust hazardous or explosive materials and
vapors.

3 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Safety Information (continued)
COOKING SAFETY INFORMATION
1. Never leave the range hood unattended when in use.
2. Never cook over open ames under the range hood.
1. Always turn the range hood on when cooking at high heat
or when cooking aming foods.
2. If you choose to hang the range hood as below (Fig. 1) distance
(D) from the cooktop surface, use extra caution as the surface
of range hood may be extremely hot to the touch. For this unit,
(D in Fig. 1) is 458 mm - 710 mm (18 in - 28 in). If you choose
an 18 in installation, the temperature of the unit surface will
be high if the unit is operated under high power cooking for a
certain amount of time.
3. Use caution when cooking with oil or with deep-fryers.
Overheating may cause oil to reach its ash point and ignite.
Used oil will ignite at lower temperatures than fresh oil. Heat
oils slowly on low to medium setting.
4. Avoid boil overs, as they may cause smoking and greasy
spillovers that could ignite.
5. To prevent burns or res, always use cookware appropriate to
the size of the heating element that you are using.
6. In event of a cooking re, observe the following:
-Be careful to avoid burns.
- Smother ames with a close-tting lid, cookie sheet, or
metal tray, then turn off the burner. If the ames do not go
out immediately, evacuate and call the re department.
- Never pick up a aming pan.
-Do not use water, including wet dishcloths or towels, as you
could cause a steam explosion.
- Use an extinguisher only if: (a) you have a class ABC
extinguisher and you know how to operate it, (b) the re is
small and contained in the area where it started, (c) the re
department is being called, and (d) you can ght the re with
your back to the exit.
CLEANING SAFETY INFORMATION
1. The fan and lters must be cleaned periodically and kept free
from accumulation of cooking residue. Old and worn lters must
be replaced immediately.
2. Never disassemble parts to clean. Parts should be disassembled
by qualied persons only.
WARNING: To reduce the risk of re, use only metal duct
work. Never use plastic duct work.
WARNING: To reduce the risk of re or electric shock, do
not use this range hood with with any external solid state
speed control device.
CAUTION: For general ventilation use only. Do not use the
range hood fans to exhaust hazardous or explosive vapours.
CAUTION: Never dispose of cigarette ashes, ignitable
substances, or any foreign objects in fans.
CAUTION: At least two people are needed to move and
safely install the unit. Failure to properly lift the range hood
could result in product damage or personal injury.

4
ENGLISH
Warranty
ONE YEAR LIMITED WARRANTY
A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or
damage that could have been discovered or avoided by proper inspection and testing prior to installation.
Conglom Kitchen & Bath warrants this product to be free from defects in materials or workmanship for one (1) year from the date of purchase.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Conglom Kitchen & Bath for all
warranty claims.
This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the
manufacturer’s instructions. It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen &
Bath replacement parts, (Replacement parts may be obtained by e-mail at [e-mail] or by calling 1-877-333-0098
between 8:30 am - 5:00 pm EST) installation error, abuse, misuse or improper care and maintenance (whether performed by a plumber,
contractor, service provider or member of the purchaser’s household). The warranty excludes damage due to aggressive air or water
conditions, harsh or abrasive cleaners and/or materials.
Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this
product. We will not be held liable for inconvenience caused by loss of use of this product, costs incurred for labour or materials, removal
and installation of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or
replacement are the responsibility of the user.
Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be defective
under normal use and service during the warranty period.
Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable
items include, but are not limited to:
-Improper installation not in accordance with manufacturer’s instructions.
-Dents and/or scratches incurred during shipping, handling, or installation.
- Change in colour or nish due to chemical usage.
-Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of abrasive cleaners.
-Alterations made to the unit by the purchaser or installer.
- Damage caused by accidental impact, re, ood, freezing, and normal wear.
- Bends and warping caused by forced connections, over-tightened ttings, and inadequate support during installation.
-Any defects or damage to light bulbs.
This warranty does not extend to commercial and institutional installation or use.
WARRANTY CLAIM PROCEDURE
If a claimable defect occurs or replacement parts are needed, please contact our customer service team at [e-mail]
or 1-877-333-0098 (Service available in English and French, Monday - Friday from 8:30 am - 5 pm, EST).
Before you make your call, please ensure that you have:
-Model number or description.
-Proof of sale.
-Details regarding the defect and/or part number.
-Name(s) and address(es) of the owner and/or installer.

5 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Pre-Installation
TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)
Measuring tape Level Utility knife
Pencil Tape Adjustable
wrench
Phillips screwdriver Flathead
screwdriver
Needle nose
pliers
Hammer Electric drill Safety goggles
Safety gloves

6
ENGLISH
Pre-Installation (continued)
PACKAGE CONTENTS
D
Part Description Quantity
A Range hood 1
BAluminum & charcoal lter 1
C Square damper (located on the hood) 1
D Round damper (located on the hood) 1
HARDWARE INCLUDED
NOTE:
Parts not shown to actual size.
AA BB
Part Description Quantity
AA Long tapping screws (ST4x18mm) 4
BB Short tapping screws (ST4x10-F-Hmm) 8

7 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Pre-Installation (continued)
PLANNING INSTALLATION
Number of people required: 2 or more
Carefully check the range hood for damage and for missing parts
prior to installation. If there is any damage or if you are missing parts,
do not proceed with the installation. Report damage and missing
parts immediately. Do not dispose of packaging before you are
satised with your new range hood.
1. Before installation, measure all distances to ensure the proper
position of the range hood (A).
-The distance (1) from the cooking surface to the range hood
must be at least 458 mm (18 in). For the best performance,
do not install the range hood more than 710 mm (28 in)
above the cooking surface.
- Dimension (2) should be at least 762 mm (30 in). The range
hood should be approximately the same size as the cook top.
2. If the bottom of the cabinet (3) above the location where the range
hood is to be installed is recessed, attach appropriately sized wood
ller strips (4) on each side using wood screws.
3. Screws are provided to secure the range hood to most types of
cabinets, but consult a qualied installer to verify that the supplied
screws are suitable for your cabinets.
4. Put a thick, protective covering over your counter, cooktop, or
range to protect it from damage and dirt during installation.
Remove any hazardous objects around the area.
WARNING: Always wear safety goggles and gloves during
installation.
VENTING OPTIONS:
a. Determine if your existing venting system is top venting or back venting, and ensure that the openings in the cabinet or wall for the
damper and for power access are in appropriate locations and are of appropriate sizes, as per Fig. 3 if it is top vent or Fig. 4 if it is
back vent. For top venting option (Fig. 3), if you are using the round damper, the opening should be A and B only. If you are using the
square damper, opening should be B and C only.
b. If this is a new installation, choose the venting method that suits your needs. Cut out openings for the damper and for power access
in the cabinet bottom or exterior wall, depending on the direction of venting chosen.
4.72”
(120mm)
7”(177mm)
A
B
CC

8
ENGLISH
Pre-Installation (continued)
FOLLOW THESE GUIDELINES WHEN INSTALLING DUCT WORK:
-Your venting system must vent to the outdoors either horizontally through the back wall (13) or vertically through the roof (14)
(refer to Fig. 5/Fig. 6/Fig. 7).
-Use round metal duct work with a uniform diameter of 177 mm (7 in). The total duct run in the venting system should be not more
than 10.7 m (35 ft).
- Calculate the total effective length of the duct work by adding the equivalent lengths in the table shown (Fig. 9). For each tting
used add the length of the equivalent straight duct used in the system.
- Fasten all connections between pieces of duct with sheet metal screws and tape all joints with certied duct tape.
-If you must turn the path of the duct work using elbows, keep the number of elbows to a minimum for effective performance and
use no more than three 90° elbows. Ensure that there is a minimum of 458 mm (18 in) of straight vent between each elbow. Elbow
as far away from the range hood’s exhaust opening as possible.
- Cap the exterior of the duct with a wall cap (15) or roof cap (16). Never use 102 mm (4 in) laundry-type wall caps. Use caulking to
seal exterior wall or roof opening around the cap.
-The venting system must have a damper. If the roof or wall cap has a damper, do not use the damper supplied with the range hood.
13
15
Horizontal Wall Venting
Fig.5
Vertical Roof Venting
14
16
Fig.7
13
Horizontal Wall Venting
Fig.6
15
For inside venting system (air does not exhaust to outdoors) (Fig. 8):
Please refer to the Installation section. The cover on the top plate will be removed and air will be exhausted through the charcoal lter and
out from 17.
17
Fig. 8
Equivalent Length Chart
Type of duct Length added
45° Elbow 0.91 m (3 ft)
90° Elbow 1.52 m (5 ft)
90° Flat elbow 3.66 m (12 ft)
2.74 m (9 ft) Straight duct 2.74 m (9 ft)
Wall cap 0 m (0 ft)
Fig. 9

9 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Pre-Installation (continued)
WIRING CONNECTION REQUIREMENTS
Installation work and electrical wiring must be done by a qualied
person(s) in accordance with all applicable codes and standards,
including re-rated construction.
OBSERVE ALL GOVERNING CODES AND ORDINANCES WARNINGS
-Electrical grounding is required for this range hood. Check with
a qualied electrician if you are not sure whether the range
hood is properly grounded.
- Failure to follow electrical requirements may result in a re.
-A fuse in the neutral or grounding circuit could result in
electrical shock.
-If the hot/cold water pipe is interrupted by plastic nonmetallic
gaskets or other materials, DO NOT use for grounding.
-DO NOT GROUND TO A GAS PIPE.
IMPORTANT: It is the customer’s responsibility to contact a qualied
electrical installer and assure that the electrical installation is adequate
and complies with the National Electrical Code, or CSA standards, as
well as all local codes and ordinances.
3. Save installation instructions for electrical inspector’s use.
4. If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine if the
ground path is adequate.
5. DO NOT use an extension cord or adapter plug with this
appliance.
6. The range hood must be connected with copper wire only.
7. The range hood should be connected directly to the junction (or
circuit breaker) box through exible, armoured or nonmetallic
sheathed copper cable. Allow some slack in the cable so the
appliance can be moved if servicing is ever necessary.
8. A UL listed or CSA approved conduit connector must be provided
at each end of the power supply cable (at the range hood and at
the junction box).
9. When making the electrical connection, cut a 3.2 cm (1-1/4 in hole
in the wall. A hole cut through wood must be sanded until
smooth. A hole through metal must have a grommet.
10. When cutting or drilling into the wall or ceilling, do not damage
electrical wiring and other hidden utilities.
11. Wire size must conform to all local codes and ordinances. The
latest edition requirements of the National Electrical Code ANSI/
NFPA 70, or the latest edition CSA Standards C22.1-94, Canadian
Electrical Code Part 1 and C22.2 No. 0-M91.
DANGER: Risk of electrical shock. This range hood must
be properly grounded.
DANGER: Turn off the power circuit breaker or the
power switch on the junction box before installing this
unit. Touching circuitry inside the range hood while it is
energized will result in death or serious injury.
DANGER: All electrical wiring must be properly installed,
insulated, and grounded. Improper insulation and grounding
will result in deadly electrical shock.
NOTE:
Temporarily wire the range hood to test it for proper operation. If
the range hood does not operate correctly, do not proceed with the
installation.
-Use the power supply cable to connect the range hood
(A) directly to the junction box or circuit breaker box.
Use a exible, armoured, or nonmetallic sheathed
copper cable only. Never use an extension cord or
adapter plug.
- Connect a UL-listed or CSA-approved conduit
connector to each end of the power supply cable
(at the range hood and at the junction box). Connect
the 2 colored wires from the range hood (A) to the
corresponding wires from the electrical source: black
to black (live), white to white (neutral), and the house
grounding wire to the green ground screw. Use either
the top hole (1) or the back hole (2) of the range hood
depending on your installation type.
-Turn the power on, and ensure that the lights and the
fan are operating correctly.
-Once you have tested the electrical connection,
disconnect the power supply cable and wires from the
electrical source before proceeding with the rest of the
installation.
BLACK WIRES 1
WHITE WIRES
GREEN GROUND SCREW
2

10
ENGLISH
Installation
REMOVING THE ELECTRICAL KNOCK-OUT HOLE
WARNING: Always wear safety goggles and gloves during
installation.
- Choose the appropriate electrical knock-out hole to remove
for your installation type. Use the top hole (1) if your electrical
supply is in the cabinet and the back hole (2) if your electrical
supply is on the wall below the cabinet (refer to Fig. 10).
- Use a hammer and a athead screwdriver to gently punch
out the electrical knock-out hole.
REMOVING THE VENTING HOLE
-Choose the venting hole to remove for your installation
type. Use the top holes (3 & 4) for a top venting
installation and the back hole (5) for a back venting
installation.
-Carefully remove the cover (3, 4 or 5) of the appropriate
venting hole using a at head screwdriver or needle nose
pliers (refer Fig. 11). Be careful not to leave any debris
inside the range hood (A).
-If you are venting indoors, unscrew the 2 screws holding
cover (6) in place and remove the cover as per Fig. 12. DO
NOT REMOVE ANY OTHER VENTING HOLE COVER.
34
5
6
INSTALLING THE DAMPER
(SKIP THIS STEP IF YOU ARE USING INTERIOR VENTING)
5
D
D
BB
5
NOTE:
Only install the damper if you are using a venting system that does not
already have a damper.
If this hood replaces an existing unit, the location of the air exhaust can vary
from one manufacturer to another. Ensure that the damper ts in the existing
opening before installing.
-Choose to install the damper (C) either in the top
position (3) for top venting or in the back position (5)
for back venting. Damper (D) installs to position 3 & 4 for
top venting only.
-Install damper (C or D) into the chosen hole in the range
hood (A), ensuring that the central ap (6) goes into the
hole while the two side aps (7) remain above it.
-Lift the lid (8) of the damper and screw the damper (C) to
the range hood (A) with the two short tapping screws (BB).
-Seal the damper to the range hood (A) on all four sides with
duct tape.

11 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Installation (continued)
INSTALLING THE CHARCOAL FILTER
(SKIP THIS STEP IF YOU ARE USING EXTERIOR VENTING)
NOTE:
The charcoal lter should only be installed if you are not using an external venting system.
- Turn the lter clip to either side and lift the aluminum lter.
- Place the charcoal lter (B) in place, ensure that it covers the air outlet entirely.
- Turn the lter clip so that the end of the clip holds the lter rmly in place.

12
ENGLISH
Installation (continued)
INSTALLING THE RANGE HOOD
DANGER: Turn off the power circuit breaker or the
power switch on the junction box before installing this
unit. Touching circuitry inside the range hood while it is
energized will result in death or serious injury.
DANGER: If installing this unit over a gas range, turn off
the gas at the source before installing or servicing this unit.
-Lift the range hood (A) up under the cabinet to determine
its nal position. Mark the location of the four keyhole
mounting slots (1) on the underside of the cabinet.
-Set the range hood (A) aside on a protective surface.
-Drill four pilot holes in the locations that you marked.
-Screw the four long tapping screws (AA) into the pilot
holes. Do not tighten the screws all the way – leave
the screw heads about 7 mm (0.28 in) from the cabinet
surface.
-Lift the range hood (A) into position, feeding the power
cable and the electrical wires through the power access
opening. Allow some slack in the cable and wires so that
the appliance can be moved if servicing is ever necessary.
-Position the range hood (A) so the large end (2) of the
keyhole mounting slots (1) are over the screws (AA). Then
push the range hood (A) toward the wall so the screws (AA)
are in the neck (3) of the keyhole slots. Tighten the screws
(AA). Ensure that the range hood (A) is securely fastened to
the cabinet before releasing it.
-If applicable, test the damper blade to ensure it rotates up
and down freely.
-If applicable, connect the duct work to the range hood (A).
Seal the joints with duct tape to ensure an airtight t.
FINAL STEP
-Reconnect the power supply cable and wires to the
electrical supply. Turn the power on and ensure that the
lights and fan are operating correctly.

13 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Operation
NOTE:
The fan and lights operate independently of each other.
TURNING ON/OFF THE UNIT
-To turn on the fan, press the appropriate speed control
switch [Low Speed (3), High Speed (2)] to select the desired
level of power. Once a button is pressed, the previous
speed mode will be cancelled.
-Press the power switch (4) to turn off the fan.
TURNING ON/OFF THE LIGHTS
-Press the light switch (1) to turn on and off the lights.
12 3 4

14
ENGLISH
Maintenance
REPLACING FILTERS
When lters need replacing, exchange with similar. Also replace
lters that are damaged with punctures, bends, or broken
frames.
-Turn off the range hood and disconnect the power.
- Replace with an equivalent lter, then reconnect the
power.
REPLACING LIGHT BULBS
When light bulbs burn out, replace them with a 40W E26 base
light bulb.
-Turn off the range hood, disconnect it from its power
source, and ensure that the lights are cool.
- Turn the bulb (1) counter-clockwise and pull it out to
remove it.
-Push in the new bulb (2) and turn it clockwise. Do not
release the bulb until you are sure the bulb has been
securely installed. Then reconnect the power.
-If new bulbs do not operate, ensure that they are
inserted correctly.
DANGER: Turn off the power circuit breaker or the power
switch on the junction box before performing maintenance.
Touching circuitry inside the range hood while it is energized
will result in death or serious injury.
WARNING: Failure to replace worn out or damaged lters
will increase the risk of re.
WARNING: Light bulbs can become hot when turned on.
Do not touch bulbs until they are switched off and cooled.
Touching hot bulbs could cause serious burns.
1
2

15 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Care and Cleaning
RANGE HOOD
WARNING: Failure to maintain basic standards of care and cleaning of the range hood will increase the risk of re.
The range hood should be cleaned (regularly internally and externally) to preserve its appearance and performance.
Do: Do Not:
-Always clean in the direction of the grain (original
polish lines).
-Clean the range hood periodically with hot, soapy
water and a clean cotton cloth.
-Always rinse well with clean water two or three
times after cleaning. Wipe completely dry with a
soft non-abrasive cloth.
- After cleaning, you may polish with a non-abrasive
stainless steel polish or cleaner. Always rub lightly
and with the grain
-Ensure that the venting system is free of debris, if
you have one.
-Do not use corrosive or abrasive detergents, steel
wool, or scouring pads. These will scratch and
damage the stainless steel surface.
-Do not use any products containing chloride,
uoride, iodide, or bromide on this product, as they
will deteriorate the surface rapidly.
-Do not allow cleaning compounds, salt solutions,
disinfectants, or bleaches to remain in contact with
the product for extended periods of time.
-Do not allow any deposits to remain for long
periods of time on the range hood. Rinse with
water immediately and wipe dry with a clean cloth.
-Do not let plaster dust or any other construction
residue enter the hood. During construction or
renovation, cover the hood.
-Combustible products used for cleaning such as
acetone, alcohol, ether, or benzol are highly explosive
and should never be used close to a range or stove.
FILTER
The lter tted by the factory is intended to lter out residue and grease from cooking. You do not need to replace them on a regular basis,
but you should keep them clean.
Do: Do Not:
- Clean the lter once a month using non-abrasive
detergents, either by hand or in the dishwasher.
When using a dishwasher, set the dishwasher to
a low temperature and a short cycle setting. The
lter may become discoloured in a dishwasher, but
this does not affect its performance.
- Allow lters to completely dry before re-installing
them in the range hood.
- Do not allow oil to accumulate over more than 80%
of the lter surface. Oil accumulations may drip oil
onto the range.
- Do not wash charcoal lter. The charcoal lter
should be replaced when it is covered in grease
and has reached its maximum absorbancy.

16
ENGLISH
Troubleshooting
DANGER: Turn off the power circuit breaker or the power switch on the junction box before performing maintenance.
Touching circuitry inside the range hood while it is energized may result in serious injury or death.
Problem Solution
The range hood will not operate. -Check that the power supply cable and all electrical wiring are properly
connected.
-Check that the power is turned on at the junction box or circuit breaker.
-Check that the wiring between the switch control and the control board are
connected properly.
The range hood vibrates when the fan is operating. -Check that the range hood has been secured properly to the wall. Tighten into
position, if necessary.
-Check that the motor is secured in place. If not, then tighten the motor in place.
-Check that the fan is not damaged. If so, replace the fan.
The fans seem weak. -Check that the duct size used is at least 177 mm (7 in) round. The range hood
will not function efciently with insufcient duct size.
-Check that the duct is not clogged with debris and the tight mesh on the wall
cap, if applicable, isn’t restricting air ow.
-Check that the damper unit is opening properly.
-Check that no birds or animals have nested in the duct.
The lights work, but the fan is not spinning, is stuck,
or is rattling. -The thermal protection system detects if the motor is too hot to operate and
shuts the motor down. In this case, the motor will function properly after the
thermal protection system cools down (after approximately 10 min).
-Check that the fan isn’t jammed or scraping the bottom.
-If nothing else works, the motor may be defective or seized. If so, replace the
motor.
The range hood is not venting properly. -Check that no birds or animals have nested in the duct.
-Check that the distance between the cooktop and the bottom of the range hood
is between 458 mm (18 in) and 710 mm (28 in).
-Check that duct work follows all requirements. Use round metal duct work with
a uniform diameter of 177 mm (7 in). The length of duct work must not exceed
35 ft (10.7 m). Reduce the length of duct work and the number of elbows if
necessary. Ensure that all joints are properly connected, sealed, and taped.
-Check that the duct does not open against the wind.
-Ensure that the power is on high speed for heavy cooking.
-Close all windows nearest to the range hood to eliminate sudden air gusts.
-To enhance the performance of the range hood, open slightly a window on the
opposite side of the house where the range hood vents outdoors.
A light does not work. -Check to see if light bulb is burnt. If so, replace.
-Check the light bulb to see if it is loose. If so, tighten.
-Remove the problem bulb and insert one you know is working. If the properly
functioning light does not come on, the problem may be the light assembly.
Have the light assembly serviced or replaced.

17 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Specications
Model Dimensions Rating Control Type Fan CFM Speeds Light Bulb Wattage Venting Options
QR049
757 mm (29.8 in) W
120V~60Hz
1.2A Push Button 220 ±
10%
High
2 x 40W Incandescent
E26 base light bulb
Top venting
Back venting
Recirculating/
Inside venting
450 mm (17.7 in) H
Low
127 mm (5 in) H
WIRING DIAGRAM
BROWN
BLACKL
120V~60Hz
BLACKL1
L
2x40W E26
2
WHITE
YELLOW & GREEN
NWHITE
WHITE
ORANGE
BLUE
BLUE
MOTOR
RED
RED

18
ENGLISH
Specications (continued)
EXTERNAL DIAGRAM OF RANGE HOOD
245mm (9.64 in)
189mm (7.44in)
519 mm (20.43 in)
214 mm
(8.42 in)
20 mm
(0.78 in)
20 mm
(0.78 in)
88 mm
(3.46 in)21 mm
(0.82 in)
88 mm
(3.46in)
188 mm (7.4 in)12 mm
(0.47 in)
26 mm
(1.02 in)230 mm
(9.05 in)
53 mm
(2.08 in)
120 mm
(4.72 in)
39 mm (1.53 in)
52 mm (2.04 in)
706mm (27.79in)
757mm (29.8 in)
230 mm (9 in)
38 mm
(1.5 in)
50 mm (1.97 in)
250mm (9.84 in)
250mm (9.84 in)
757 mm(29.8 in)
170 mm (6.7 in)
450mm (17.7 in)
127 mm (5 in)

19 CONGLOMKB.COM
Please contact [e-mail] or 1-877-333-0098 for further assistance.
ENGLISH
Service Parts
If you are missing parts or if you require replacement parts, please contact our customer service team at [e-mail] or
1-877-333-0098 (8:30 am – 5 pm, EST, Monday–Friday). Identify the required part(s) and have the part number(s) ready.
A
G H J K L
MNP Q R S
B C D E F
Part Description Code Quantity
A Square Damper QHR164 1
B Switch QHR165 1
C Junction Box QHR166 1
D Motor QHR167 1
E Filter Clip QHR168 1
F Motor Bracket QHR169 1
G Round Damper QHR170 1
H Light Cover QHR171 2
J Blade QHR172 1
K Bulb Holder QHR173 2
L Bulb QHR174 2
M Blade Guard QHR175 1
N Wire Protection Box QHR180 1
P Charcoal Filter QHR176 1
Q Aluminum Filter QHR177 1
R Long Tapping Screws (ST4x18mm) QHR178 4
STapping Screws (ST4x10-F-Hmm) QHR179 8

20
ESPAÑOL
Índice
Índice ....................................2
Información de seguridad.......................2
Garantía
Un año de garantía limitada..........................4
Procedimiento de reclamación de garantía..............4
Preinstalación
Herramientas / Materiales necesarios..................5
Contenido del paquete..............................6
Accesorios incluidos ...............................6
Planicación de la instalación ........................7
Instalación ................................ 10
Funcionamiento ............................ 13
Mantenimiento
Reemplazo de los ltros ...........................14
Cambio de bombillas ..............................14
Cuidado y limpieza
Campana extractora. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Filtros..........................................15
Solución de problemas ....................... 16
Especificaciones
Diagrama de cableado.............................17
Diagrama exterior de la campana extractora ...........18
Refaccións ................................ 19
Información de seguridad
LEA Y GUARDE ESTAS INSTRUCCIONES
Advertencia: Para reducir el riesgo de incendio, descarga
eléctrica o lesiones a las personas, tenga en cuenta lo
siguiente:
1. Use esta unidad únicamente de la manera que fue diseñada por
el fabricante. Si tiene alguna pregunta, póngase en contacto
con el fabricante.
2. Antes de prestar servicio a la unidad o limpiarla, apague el
suministro eléctrico en el panel de servicio y bloquee el medio
de desconexión del servicio para evitar el encendido accidental
del equipo. Cuando el medio de desconexión del servicio no
se puede bloquear, adhiera de manera segura un dispositivo
visible de advertencia al panel de servicio, tal como un rótulo.
3. El trabajo de instalación y el cableado eléctrico deberá ser
realizado por personas calicadas de acuerdo con todos los
códigos y normas aplicables, lo que incluye una construcción
calicada a prueba de incendio.
4. Se necesita una cantidad suciente de aire para lograr
una correcta combustión y escape de los gases a través
del conducto de humos (chimenea) de los equipos que
queman combustible para evitar el contratiraje. Siga las
especicaciones del fabricante del equipo de calefacción y
las normas de seguridad, como las que publica la Asociación
Nacional de Protección contra Incendios (National Fire
Protection Association, NFPA) y la Sociedad Estadounidense de
Ingenieros de Calefacción, Refrigeración y Aire Acondicionado
(American Society for Heating, Refrigeration and Air
Conditioning Engineers, ASHRAE), así como las que aparecen
en los códigos de las autoridades locales.
5. Al cortar o perforar en una pared o techo, evite dañar el
cableado eléctrico u otros materiales ocultos.
6. Los ventiladores con conductos siempre deben tener salida al
exterior.
PELIGRO: Apague el disyuntor o el interruptor de alimentación
en la caja de derivación antes de instalar o dar servicio a esta
unidad. No toque los circuitos que se encuentran dentro de la
campana extractora mientras está conectada, pues esto puede
ocasionar la muerte o una lesión grave.
PELIGRO: Todos los cables eléctricos deben instalarse, aislarse
y conectarse a tierra apropiadamente. Si el aislamiento y la
conexión a tierra no son adecuados, existe el riesgo de que se
produzca una descarga eléctrica mortal.
PELIGRO: Si se instala esta unidad sobre una estufa de gas,
apague la fuente de gas antes de instalar o dar servicio a esta
unidad.
ADVERTENCIA: No intente instalar o dar servicio a esta unidad
si usted no tiene los conocimientos técnicos o de electricidad
necesarios, ya que esto puede ocasionar una lesión personal.
ADVERTENCIA: La unidad tiene bordes alados. Siempre
use guantes de seguridad durante la instalación, limpieza o
mantenimiento.
ADVERTENCIA: Siempre deje las parrillas y los ltros de
seguridad en su lugar. Sin estos componentes, cuando los
ventiladores están en funcionamiento se puede atorar el cabello,
los dedos o la ropa suelta.
ADVERTENCIA: Manténgase lejos del ventilador giratorio
cuando el motor esté funcionando.
ADVERTENCIA: Mantenga este aparato limpio y libre de
grasa y acumulación de residuos en todo momento para evitar
incendios.
PRECAUCIÓN: El único uso de este dispositivo debe ser de
ventilación. No lo utilice para descargar materiales y vapores
peligrosos o explosivos.