Westinghouse WRCG932SB User manual

INSTALLATION AND USER MANUAL
WRCG932SB, WRCG933SB Canopy Rangehood
WRCG943SB Canopy Rangehood

CONGRATULATIONS
Congratulations and thank you for choosing our canopy
rangehood. We are sure you will find your new rangehood
a pleasure to use. Before you use your rangehood, we
recommend that you read through the whole user manual,
which provides the description of the rangehood and
its function.
To avoid the risks that are always present when you use an
electrical appliance it is important that the canopy
rangehood is installed correctly and that you read the
safety instructions carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet for
future reference and pass it on to any future owners. After
unpacking the canopy rangehood please check it is not
damaged. If in doubt, do not use the appliance but contact
your local Electrolux Service Centre.
Conditions of use
This appliance is intended to be used in household and
similar applications such as:
working envionments
type environments
Record model and serial number here:
Model:
Serial No:
TIPS & INFORMATION
IMPORTANT – CHECK FOR ANY DAMAGES OR MARKS. If you find
the rangehood is damaged or marked, you must report it
within 7 days if you wish to claim for damage/marks under
the manufacturers warranty. This does not affect your
statutory rights.
UNPACKING
Check that the cooker hood has no damage.Transportation
damage should immediately be reported to the company
responsible for the transportation.
Damage, faults and missing details should immediately be
reported to the retailer. Take care of the packing materials so
that small children cannot play with them.
ENVIRONMENTAL TIPS
INFORMATION ON DISPOSAL FOR USERS
dispose of those materials through your local recycling depot
or by placing them in appropriate collection containers.
local authorities and ask for the correct method of disposal.
CONTENTS
Important safety instructions
Description of your rangehood
Components list
Technical specifications
Rangehood dimensions
Installation
Using your rangehood
Care & maintenance
Troubleshooting
Optional ducting accessories
Warranty
. . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2

IMPORTANT SAFETY INSTRUCTIONS
This manual explains the proper use of your new
Westinghouse canopy rangehood. Please read
this manual carefully before using the product.
This manual should be kept in a safe place for
handy reference. This canopy rangehood is a
domestic appliance which has been
manufactured and tested to comply with
Australian and New Zealand Standard
AS/NZS 60335.2.31.
Meanings of symbols used in this manual are
shown below:
CAUTION
This symbol indicates never to do this.
This symbol indicates always do this.
TIPS & INFORMATION
This symbol indicates tips and information about use of
the appliance.
ENVIRONMENTAL TIPS
This symbol indicates tips and information about
economical and ecological use of the appliance.
3
Grease filters must be removed every four
weeks (maximum) for cleaning to reduce
the risk of fire.
The exhaust from the canopy rangehood
must not be discharged into any heating
flue, which may carry combustion products
from other sources. (Fig 1)
Exhaust air must not be discharged into a
wall cavity, unless the cavity is designed
for the purpose.
There must be adequate ventilation of the
room when the canopy rangehood is used
at the same time as appliances burning
gas or other fuels.
Always cover lit gas burners with pots or
pans when canopy rangehood is in use.
Always switch off gas burners before you
remove pots or pans.
Do not leave lit gas burners exposed due
to the risk of fire. (Fig 2)
The hood must always be disconnected
from the electricity supply before
beginning any maintenenace work.
This canopy rangehood is not
recommended for barbecues and cannot
be installed for external use.
Failure to install the screws or fixing device
in accordance with these instructions may
result in electrical hazards.
This symbol indicates the possiblity of injury or
damage to property.
CAUTION
GENERAL WARNINGS
The appliance must be plugged into its
own dedicated 220-240V, 50Hz AC
electrical outlet.
Read the following carefully to avoid an electric
shock or fire.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning the
use of the appliance in a safe way and
understand the hazards involved. Children
shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.

4
SAFETY WARNINGS – FOR THE INSTALLER
When installing the cooker hood, make sure
you adhere to the minimum and maximum
distances from the cooker hood base to the
hob surface (refer to page 8).
Exhaust flue installation: The following rules
must be strictly followed to obtain optimal air
extraction.
Keep exhaust flue short and straight.
Do not reduce the size or restrict exhaust flue.
Keep bends in the exhaust flue to a minimum.
When using flexible flue always install duct
with helix pulled taut to minimise pressure loss.
Failure to observe these basic instructions will
drastically reduce the performance and
increase the noise levels of the cooker hood.
Exhaust air must not be discharged into a wall
cavity, unless the cavity is designed for that
purpose. The exhaust from the cooker hood
must not be discharged into any heating flue,
which may carry combustion products from
other sources.
NOTE: Some installations may require the
telescopic exhaust cover to be cut to length.
Cut with sharp tin snips or a fine-tooth hack
saw blade, taking care not to distort or dent
the exhaust cover.
1 2
ELECTRICAL CONNECTION
Check that the mains voltage matches with the
voltage on the data plate inside the canopy
rangehood. Check that the installation complies
with standards of local building, gas and
electrical authorities. Before connecting to the
mains supply ensure that the mains voltage
corresponds to the voltage on the rating plate
inside the cooker hood.
If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or similarly qualified person in order to
avoid a hazard.

DESCRIPTION OF YOUR RANGEHOOD
WRCG932SB WRCG933SB WRCG943SB
Components list
1. Upper Flue mounting bracket
2. Telescopic flue cover
3. Exhaust transition duct
4. Lower Flue mounting bracket
5. Main body and fan housing assembly
6. Glass
7. Grease filter
Additional items required for installation
tilt points
Worm drive clamps, Duct tape or cable ties
Technical specification
point
MODEL
Width
Depth
Lighting
Outlet diameter
WRCG932SB WRCG933SB WRCG943SB
338 W
V
338 W
V
338 W
V
The manufacturer reserves the right to make technical changes.
Fig. 3
1
2
3
4
1
2
3
4
5
6
7
1
2
3
4
5
6
7
5
- - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - -
- - - - - - - - -
- - - - - - - - -- - - - - - - - - - - - - - - - -- - -
- - - - - - - - - - - - - - - - - - - - - -
Qty.
1
1
1
1
1
1
1
5
6
7
750 mm - 1100mm570 mm - 900mm 750 mm - 1100mm
Power supply: 240 V 50 Hz. Connects to 10 A power
Lights: 2 x 4 watt, 240 V LED

RANGEHOOD DIMENSIONS
6
BS339GCRWBS239GCRW
5.giF4.giF
320 290
480
900
90
400
Min 570 / Max900
216
290
296
320
320 290
480
900
90
600
Min 750 / Max1100
216
290
296
320

RANGEHOOD DIMENSIONS
WRCG943SB
Fig. 6
320 290
480
900
600
Min 750 / Max1100
216
290
296
320
35
7

INSTALLATION
PRE-INSTALLATION
Before installing the cooker hood, peel off any protective coating.
INSTALLATION
1. Using a spirit level mark a vertical centre line on the wall where the hood is to be positioned, and a horizontal line
NOTE. The height of the underside of the hood body must be a minimum of 600mm* to a maximum height of 800mm.
* If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum
height for installation.
2. Mark the location for the flue cover wall mounting brackets and rangehood mounting points and anti-tilt fixing
points above the hood base using the hood base as a reference point
130 mm
250 mm
230 mm
286 mm
587 mm (WRCG933SB & WRCG943SB)
40 mm
250 mm
250 mm
Max. 1100 mm (WRCG933SB & WRCG943SB)
An g po n
Range hood
moun ng po n s
F e cover w
moun ng bracke
ng
M . 600 mm*
Max. 800 mm
Top of hob
8
LOCATION
The hood is to be mounted on the wall. When installed, the hood must be not less than 60cm above electric burners or
65cm above gas or mixed-fuel burners.
Distance from hood base to top of hob
hob type minimum* maximum
gas 650mm 800mm
electric 600mm 800mm
* If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height
for installation.
Max. 900 mm (WRCG932SB)
387 mm (WRCG932SB)

INSTALLATION
3. Install flue cover wall mounting brackets with suitable
fixings. Install suitable screws for rangehood mounting
points (to support a total weight of 30kg) to the wall as
2mm
A
B
6. Hang the body hood on the mounting screws then
AB
4. Remove the protective plastic film from the hood body
and telescopic flue cover carefully, then assemble
together.
9
B
marked (Fig. 8)

INSTALLATION
Depending on the preferred installation/ducting mode,
follow step 7a or 7b below.
7a.Recirculating mode
secure the recirculating T-piece to the wall with suitable
pipe between T-piece and reducer.
Use cable ties or suitable duct tape to secure flexible
NOTE: When installed in recirculating mode, it is
recommended to use a carbon filter (included in
emitted back into the room.
7b.Ducted mode
combustible flue pipe. Continue the centre line to the ceiling.
suitable duct tape to secure flue pipe to the transition duct.
the roof to external ‘roof cowl’ to vent exhaust externally.
Do not vent into the ceiling cavity.
NOTE: To ensure optimum performance of the
rangehood, the use of rigid ducting (optional AR150F)
is recommended. The use of bends should be avoided.
Rigid flexible ducting is suitable, although loose flexible
ducting is unacceptable. All ducting must be fire retardant.
10
screws/fixings (optional kit AR610RK). Install flexible
recirculation kit AR610RK) to prevent odours being
pipe to T-piece and reducer (Fig. 14) .
Fit flue pipe to the exhaust transition duct. Use calbe ties or

INSTALLATION
8. Electrical connection
Check that the installation complies with the standards
of local building, gas and electrical authorities. Before
connecting to the mains supply ensure that the mains
voltage corresponds to the voltage on the rating plate
inside the rangehood.
9. Fix telescopic flue cover to the wall mounting bracket
with screws supplied. Ensure that the upper section
is extended.
Fig. 15
Fig. 16
Care must be taken to ensure the screws (supplied in
accessories bag) are not crosss threaded when attaching
the upper flue cover. If installed in recirculating mode,
insert the optional carbon filter (inclued in recirculation
kit AR610RK). To complete the cooker hood installation,
insert the three filters to the underside of the hood body.
Place back edge of filter into position and push up front
edge so that the filter clips into place.
Your Electrolux cooker hood is now ready to use.
IMPORTANT!
10.
Insert the glass into the slot on the main body as show
in Fig.17, then pull the latchs to inner side, same time
push the glass in place (Fig.18).
* Please remove the grease filter before installing the glass.
* We recommend that two people carry out this installation
step.
Side view
Fig. 17
Fig. 18
11

CONTROL PANEL
normal conditions and a high speed when odours are
more concentrated.
start cooking.
after cooking or until all odours have dispersed.
A. Filter
to be cleaned .
deactivated with a single touch.
B. Timer
Using the Timer
rangehood will continue to run for an additional 5 to15
minutes, depending on the selected fan speed .
then reduce to medium for 5 minutes, then reduce to low
after cooking.
C. Lights
To switch Lights ON and OFF
D. Power on/off
E. Fan speed 1- light frying/boiling
F. Fan speed 2- frying/wok cooking/heavy boiling
G. Fan speed 3- grilling, intensive frying and wok
cooking
A B C D E F G
CARE & MAINTENENCE
External surfaces are susceptible to scratches and
abrasions, so please follow the cleaning instructions
to ensure the best possible result is achieved without
damage.
CAUTION
Cleaning the hood
a solution of water and mild washing up liquid. Clean
stainless steel surfaces using non-abrasive cleaning
products that are specifically for use on stainless steel.
To ensure the best results also use an even pressure and
follow the grain of the stainless steel. Use of a soft cloth
reduces the risk of scratching. If the cloth is wet ensure
that a dry soft cloth is used to wipe down the surface
and apply stainless steel protector to reduce the risk of
any surface rust appearing.
products or products containing bleach.
protective grid.
damp cloth and mild washing up liquid.
cause grease deposits that could cause a fire.
Removing the metal grease filters
then pull it down and out.
NOTE. This product is fitted with a safety cutout device.
If the cooker hood is installed to close to the cooktop, flambe cooking, operating the cooktop without cooking utensils and
blocked filters may activate the safety cutout device. If the hood stops during operation, correct the faults and allow time
for the safety cutout device to reset, the cooker hood will then function correctly.
12
Fig. 19
unit. See Fig. 18 below.

CARE & MAINTENENCE
Hand washing
Soak grease filters for about one hour in hot water with a
grease-loosening cleaner, then rinse off thoroughly with hot
water. Repeat the process if necessary. Refit the grease filters
when they are dry.
Dishwasher
Changing the LED lamps
powerful washing program and highest temperature, at
least 65°C. Repeat the process. Refit the grease filters when
they are dry. When washing the metal grease filter in the
dishwasher a slight discolouration of the filter can occur, this
does not have any impact on it’s performance.
If LED lamps need replacing, they must be replaced by
lamps as stated in the technical specifications.
NOTE: The metal grease filters must be removed and
washed,either by hand or in the dishwasher, every four weeks.
loosening cleaner (never use caustic detergents, abrasive
powders or brushes).
Charcoal filter
the hood in the recirculation function.
rule, the activated charcoal filter should be changed once
every four months.
Fitting the charcoal filter
to cover the plastic grids that protect the fan wheel.
serial number when ordering replacement filters. This
information is shown on the registration plate located on
the inside of this unit.
local Service Centre.
Ensure that the appliance is switched off before carrying
out maintenance to avoid any possibility of electric shock.
13

TROUBLESHOOTING GUIDE
REMEDYP R O B L E M
The cooker hood will not start Check that the hood is connected to an electrical supply
Check that a fan speed has been selected
Check that the fan speed is set high enough for the task
The grease filters are clean
The kitchen is adequately vented to allow the entry of fresh air
If set up for recirculation, check that the charcoal filter is still effective
Do not operate cooktop without pots/pans
If set up for extraction, check that the ducting and outlets are not blocked
Do not flambe under cooktop
The safety cut-out device has been tripped – turn off the hob and wait for the device
to reset. Check and clean filters. If the hood has been installed below the heights
indicated in the installation instructions the motor will cut out frequently which will
damage the hood.
The cooker hood is not working
The cooker hood has switched off
during operation
If you have completed all of the above checks and are still experiencing difficulty, please contact your local Electrolux
Service Centre.
NOTE: This product is fitted with a safety cutout device.
utensils and blocked filters may activate the safety cutout device. If the hood stops during operation, correct the faults
and allow time for the safety cutout device to reset, the cooker hood will then function correctly.
14

AR150RC
AR150F
AR610FS
AR610CF
AR610RK
AR150WV
OPTIONAL DUCTING ACCESSORIES
Part Numbers Description
AR150RC
AR150WV
150mm G/Bond Roof Cowl
150mm Wall Vent & duct
Replacement carbon filter
Stainless steel exhaust cover extension 1200mm
T-piece & carbon filters
15
AR610RK
AR150FD AR125FDA
150mm aluminum flexible duct
125mm aluminum flexible duct
50mm wide aluminum tape (55m roll)
AR150FD
AR125FDA
1438124

AUSTRALIA
phone: [phone]
fax: [phone]
email: [email protected]
web: www.westinghouse.com.au
NEW ZEALAND
phone: [phone]
fax: [phone]
email: [email protected]
web: www.westinghouse.co.nz
For more information on all westinghouse appliances,
or for dimension and installation information, call into your retailer,
phone or email our customer care team or visit our website:
Top Service encompasses the after sales service
provided by The Electrolux Group to consumers
including delivery, home service and spare parts.
Part number: 60901725 Issue B
© 2015Electrolux Home Products Pty Ltd
ABN 51 004 762 341
Print code: WRCG932SB_WRCG933SB_WRCG943SB_CHJul15
Westinghouse. We are part of the Electrolux family.
Share more of our thinking at www.electrolux.com
TOP SERVICE