Wet Sounds XS-XXX User manual

25/08/10- 323099/167
Wet Sounds Inc.
1-877-938-7757
www.wetsounds.com
[email protected]
XS-XXX Marine Subwoofer
Owner’s Manual

12 inch marine subwoofer
impedance = Dual 2 ohms
Revc= 0.95 ohm
Znom= 1.0 ohm
Sd= 0.053 m2
Mmd= 247 g
Power Handling RMS/Max= 750/1500W
Xmax= 12 mm
Krm= 6.40 mohm
Kxm= 85.13 mH
Erm= 0.743
Mms= 254g
Fo= 32 Hz
BL= 11.4 Tm
SPLo= 90 dB
Exm= 0.484
Vas= 38 l
Qms= 7.99
Qts= 0.36
Qes= 0.38
Levc= 0.93 mH
Wet Sounds professional marine audio products represent the ultimate in high performance marine audio. Wet Sounds speakers are
specifically engineered to withstand the rigorous marine environment. The XS series of speakers were designed to provide amazing
output combined with a cutting edge style. Utilizing state of the art acoustic engineering and three dimensional computer aided
design, the XS series represent the most advanced marine speakers in the world. Please take a moment to read the instruction
manual before starting your installation. If you have any questions or concerns, please contact you certified Wet Sounds dealer or
Wet Sounds at 877-Wet-Spkr.
Thank You for purchasing this Wet Sounds product !
SPEAKER SPECIFICATIONS
The Wet Sounds XS series of subwoofers is a line of advanced
low frequency transducers. These subwoofers use advanced
materials throughout such as our exclusive rubber spider and
powder coated cast aluminum frames. Wet Sounds has
developed a rubber spider for the XS series of subwoofers.
Rubber is used for the spider as most marine speakers use cloth
that will deteriorate over time. The XS series speakers are built to
last in the harshest environments. The XS subwoofers utilize a
cast aluminum frame that is powder coated to provide a solid non
flexing mount. Advanced acoustical technologies like perimeter
venting, high temperature voice coils and gold plated binding
posts also help to make the XS series one of the most advance
marine subwoofers on the market.
Limited Warranty
XS-XXX
What This Warranty Covers
How Long Coverage Last
What Is Not Covered
What Wet Sounds, Inc. Will Do
How to Obtain Warranty Service
Internet Warning
This is a “Limited” warranty. This warranty covers any defects in materials and workmanship and warranty only applies to the original purchaser and is not
transferable. This warranty is also only valid if the original purchase was made from an authorized Wet Sounds™ dealer.
This warranty runs for one year from the date of the purchase. It is recommended to REGISTER your warranty online within 45 days of your purchase at
www.wetsounds.com - click on “warranty registration”
Wet Sounds, Inc will repair any part of your product that proves to be defective in materials or workmanship. In the event repair is not possible, Wet Sounds, Inc
will replace the product in question. If it is deemed necessary Wet Sounds, Inc. will either replace the entire product with a refurbished unit or it will be
replaced with a model that is similar in price if that model is no longer available. Labor cost and materials needed to complete this service will be at no charge to
the purchaser. Additionally, the cost of shipping TO the consumer is also covered under this warranty.
Contact Wet Sounds, Inc. either by phone at 877-938-7757 or by email at warr[email protected]. A service representative will assist you in the necessary
actions to verify that the problem that you are experiencing is covered under warranty. If it is in fact a warranty issue, Wet Sounds will issue an RA number for
tracking purposes and give instructions on sending the product in for evaluation.
Wet Sounds, Inc. products sold on any non authorized web site or internet auction site are void of any and all manufacturer's warranty. Please contact Wet
Sounds™ at 877-938-7757 or visit our web site at www.wetsounds.com to search for an authorized site and/or an authorized retailer near you.
This warranty does not cover fading or discoloration caused by exposure to sunlight or chemicals such as ammonia, household bleach, or any cleaning material that
contains abrasive substances. (For information on how to prevent fading or discoloration, consult for recommendations on cleaning
products) Wet Sounds, Inc. does not cover the cost for removal and reinstallation of any kind. Additionally, shipping TO Wet Sounds, Inc. is covered by the
purchaser This warranty is void and inapplicable if Wet Sounds™ deems that the product was abused or misused; including but not limited to Speaker product that
has been improperly-powered (under or over powered), causing thermal (burnt voice coil) and/or mechanical failure (torn surrounds or spiders), damage caused by
accident, mishandling, improper installation, negligence, normal wear and tear, excessive water or heat damage, freight damage or products that have been altered
in any way. Product owned by anyone other than the original purchaser from an authorized Wet Sounds dealer. (The warranty is not transferable and will not apply
to products purchased from unauthorized dealers.) Wet Sounds is not responsible for any damages to a consumer's boat or person from a product failure. The
warranty is void if Wet Sounds deems the product was installed or used improperly. Wet Sounds shall not be responsible for any incidental or consequential
damages, except to the extent provided (or prohibited) by applicable law. This warranty gives you specific legal rights, and you may also have other rights which
vary from state.
new or a
.
.
www.wetsounds.com

HOLE TEMPLATE
XS-XXX
(0.25”)
(11.26”)
(12.20”)
6.5mm
286.0mm
310.0mm
45°
o
o
o
For best performance the walls of the enclosure should be rigid and not vibrate as a result of the internal pressures
generated by the loudspeakers. recommends constructing enclosures from medium-density fiberboard
(MDF) with a minimum thickness of 3/4”. In larger enclosures over 1 cubic foot, internal bracing that joins opposite walls
can be incorporated and the final enclosure should be as rigid as possible. All joints should be glued and fastened with
screws. Additionally, internal joints can be covered with a small bead of silicone adhesive to ensure that the enclosure is
completely air-tight. Drivers should be fastened to the enclosure with self-threading screws with adequate length and
diameter, utilizing all the mounting holes in the frame. To avoid air leakage, a foam rubber gasket or similar sealing
method should be applied between the loudspeaker and the enclosure. The external surface of the enclosure may be
painted or fabric-covered, to suit the consumer. Since low frequency sounds are not directional, subwoofer enclosures
can generally be placed anywhere within the boat, without compromising stereo imaging. However, different placement
locations of subwoofer enclosures can sometimes influence the overall quality of bass/midbass response, so you may
wish to experiment with various mounting locations before permanently mounting the woofer.
WET SOUNDS
Marine subwoofers are offered in Dual Voice Coil configuration 2+2 ohms. Voice coils can be wired in
parallel (Z = 1 ohm) or in series (Z = 4 ohms), allowing the user to properly match the driver to his amplifier.
WIRING
WET SOUNDS
series Z=4 ohms parallel Z=1 ohms
ENCLOSURE CONSTRUCTION

The Wet Sounds XS-XXX SPL marine subwoofer has been specifically engineered to produce outstanding results in both small sealed
enclosures and vented enclosures. As a rule, sealed enclosures provide better transient bass response than their vented counterparts,
although the vented enclosures generally provide more deep bass. However, both enclosure types will work in any situation.
This enclosure is made up of a totally closed, air-tight box. This type of enclosure gives excellent, tight bass response, as well as
providing an effective control of loudspeaker excursion, maintaining it within reasonable limits and generally providing lower
distortion and very high volume levels. If you build your own enclosure, recommends that you glue and screw all
joints using enough adhesive to ensure that all joints are air-tight.
WET SOUNDS
SEALED ENCLOSURES
Vented enclosures are not air-tight and incorporate an additional opening known as a port or vent, which is generally fabricated from either
plastic or cardboard tubing. The port augments the sound coming out of the woofer and is in most cases capable of going lower in frequency
than the same woofer in a sealed box. Even though vented enclosures are not air-tight, you should follow the same procedure as with
sealed boxes and glue and screw together all joints. Bellow you will find drawings for enclosures specifically designed for Wet Sounds
Marine subwoofer . The dimensions shown in drawings (already taking in account the volume occupied by the subwoofer) are intended as a
guideline and specific dimensions (HxWxD) may be used provided the internal volume of the enclosure is maintained. In the special case
of SEALED enclosures, volumes greater or smaller than specified in the table can be chosen, with different results. Smaller enclosures lead
to a more enhanced response and higher power handling whereas larger ones exhibit better transient and more extended response.
VENTED ENCLOSURES
INSTALATION SEALED AND VENTED ENCLOSURES
310 (12.20”)
O
322 (12.68")
O
O
166 (6.53")
25 (0.98")
12 (0.48")
O
O212 (8.35")
283 (11.14")
6.5 (0.25”)
(8x)
DIMENSIONS mm(”)
16.3" 18.1"
13.8"
0.79" 4.96"
PORT
SEALED ENCLOSURES VENTED ENCLOSURES
14.2" 14.57"
0.79"
V = 1.2ft3
BV = 1.78ft F = 32Hz
3/
BB B