Place the two AAA s into the remote control.
Part 5 Remote Control Unit Instruction
DC IN
IR IN
SERVICE
HDMI OUT
IR Sensor Extender cable
High Def. Flat-panel TV
DC IN HDMI IN
IR OUT
SERVICE
HDMI IN HDMI OUT
IR Blaster Extender cable
If the Infrared (IR) Blaster & Sensor (included) are connected to the
and so you can point hand-held remote controls of your HD A/V
eq uip men t a t th e r ece ive r or at your HDTV inste ad of a t t he A/V
equipment. The transmission distance is 65 feet, line-of-s ight.
r
receiver
Part 4 IR Blaster and Extender Setup
Y/Pb /Pr
Video
RGB
S-Vide o
HDMI
DC IN HDMI OUT
IRIN
12
SERVICE
Part 6 Operation
Press the POWER n on the remote
control or on the top of the
and to turn on the
and receiver.
Power on your TV set and go to the
source menu under the set menu
of your HDTV set.
Then s elect the HDMI inpu t to whic h
the receiver is connected.
Press the SOURCE n on the remote control
or on the top of the receiver to select the input
source, l available video/audio is shown on
the TV screen. If all is normal, the
POWER LED and SOURCE LED will be lit in solid
blue, and the user can press the INFO on
the remote control to check the status of signal
quality and A/V source selected.
NOT E : When the system is warming up, the RF
linking between the r and the
receiver will take up to one minute to connect.
receiver
the r
1212
NOTE:
12
12
1 2
Inte rn et
1 2
1212
e the Device
and Set up the Link
DOLBY
DIG I T A L
POWER
EXIT
MENU
SELECT
Blu-ray Player or High-Def Set-top Box or
High-Def Game Console
ZRC-0000
Bu tt on
PO W ER
IN FO .
SO U RC E
CH AN N EL
W ID E
(108 0i cont ent onl y)
FunctionDes cription
Pressto turn the
Transmitter/Receiver
on/off.
Pressto display between
"Channel","Source", "Resolution",
"WIDE mode" and' SignalQ uality'
Press this button to changethe
frequency of IR blaster among
38KH z, 4 7Kz and 58KHz.
Default frequency is 47KH z .
Press this button to change
betweenwireless channels manually
if the user experiences video noise.
Pressthisbutto n toboost video
transmissiondistancewire lessly.
The default setting is tohave
this feature disabled.
Operation
Press once to displaythe current status.
Press againto exit O SD.
Pressonce todisplaythe current"Channel" status.
Pressagain within 5 secondsto switch toanother channel,
and thechannel numberwill bedisplayed ontheOSD .
Pressthisbutto n toenable and disable W idemode.
Pressagain within 5 secondsto enable W IDE mode, and
thestatus will bedisplayedon theOSD .
Pressit whenpointingat the receiver to enter the
"Standby Mode" with theloop-through connectionis
alreadyon; press it when pointing at the transm er
to enter the "Standby Mode " with the loop-through
connection is o .
Press once to display the current frequency of IR blaster.
Pressagainto changeto next frequency, andthe frequency
will be displayed on the O SD.
If you have electronic devices such as cordless phones, wireless AC points/routers g in the 5GHz band and near the
device, the audio/video quality on the display or TV may s u er. Press the "CHANNEL" button twice on the remote control
to switch to an appropriate channel for the device.
