Whirlpool 3395314 User manual

Stacked Dryers
Instructions
Part No. 3395314 Rev. E
‘h!

Before you start...
Check locatlon where dryers will be
used. Proper installation is your
responsibility. The dryer must not be
installed or stored in an area where it
will be exposed to water and/or
weather. Make sure you have
everything necessary for correct
installation.
Each of the dryers is equipped with a
timer, selector switches and indicator
lights. The timers are set to provide 45
minutes (4 pins) of drying time when
activated by the coin slide. Timer
cams for 30-minute (6 pins) and 60-
minute (3 pins) drying timers are
supplied with the unit in the parts
bag. See Pages 8 and 9 for timer
cam changing instructions.
The coin-slide mechanisms, control
panel lock and key, coin box and
coin box locks and keys are not
included and are available from
usual industry sources.
Fire Hazard
Foryour sat&y, the Intormatlon In
this manual must be tollowed to
mlnlmlze the rlsk ot fire or exploslon
3r to prevent property damage,
personal Injury or loss 0r iire.
- Do Not store or use gasoline or
other tlammable vapors and
llqulds In the vlclnlty ot thls or any
other appliance.
-WHATTO DO IFYOU SMELLGAS:
l Do Not try to light any
appliance.
l Do Not touch any electrlcal
switch; Do Not use any phone
In your bulldlng.
l Clear the room, bulldlng or area
0r all occupants.
l lmmedlately call your gas
suppller tram a nelghbor’s
phone. Follow the gas suppller’s
Instructlons.
. It you cannot reach your gas
suppller, call the tire department.
. Never Install dryer up agalnst
draperles or curtains or on carpet.
Keep any and all Items tram klllng
or collecting behlnd the dryer.
nstallatlon and service must be
,erformed by a quailtied Installer,
iervlce agency or the gas suppller.
Post thls warnlng In a promlnent
locatlon.
It is recommended that the operator
post, in a prominent location,
instructions for the customer’s use in
the event that the customer smells
gas. This information should be
obtained from your local gas supplier.
Page 2
I
Protectlon trom weather: roper
$
operation requires tempe tures
above 45°F (7.2”C).
The wiring diagram is ed inside
the control panel and ac ess panels.
Check utllltles Proper
supplv connednonrSlk
Important: Observe all
governing codes and
ordinances.
m&t be available.
support the total
pounds per unit. weight of 315
I
Level floor: Maximum flbor slope
under dryers - 1 inch.
Ii84nEii‘NPT plugged
tapplng Is requlred.
See “Gas supply
~li;ili;iii:i’-‘i’i-i:irequirements,n Page 3.
ixhausted from
bottom, rear, left
lr right side. See
I‘Exhaust
3quirements, I
*ounded electrlcal outlet
is
Wrequired. See “Electrical
requirements,” Page 4.
Locatlon must be large enough to
fully open dryer doors. See Page 8 for
recessed area requirements and
product dimensions.
tar thls Installation.
Failure to tallow these I structlons
could result In a tire or t xploslon.
Electrlcal Shock Hazard
It Is the customer’s responslblllty:
l To contact a licensed electrlclan.
l To have dryers Installed
according to all natlonal and
local codes and ordinances.
Failure to do so could result In a tire,
electrlcal shock or other personal
InJury. Personal Injury Hazard
More than one person Is requlred to
Iltt, tilt, or move the dryers because
ot their welght and size.
Failure to tallow these lnstructlons
may result In personal Injury.

Tools needed for
installation:
adjustable wrench
IWSI
utility knife pliers
Phillips screwdriver duct tape
flat-blade screwdriver
Parts supplied for
installation:
2 slide protectors
8 screws
2 slide extensions 2. 30-minute cams
2 bolt and washer 2,60-minute cams
assemblies
4,314” wood screws
Parts owner must
supply:
1control panel lock and key
2 coin vaults and keys (E.S.D. vault must
have projecting lock.)
2 coin-slide mechanisms (vertical 8)
Parts may be ordered from
Greenwald Industries, Inc. or
Equipment Systems and Devices, Inc.
l Greenwald Industries, Inc.
1340 Metropolitan Avenue
Brooklyn, NY 11237
telephone [phone] or
toll free (800) 22 l-0982
faxno. [phone]
l Equipment Systems and
Devices, Inc.
270 New Jersey Dr.
Fort Washington, PA 19034
telephone [phone] or
toll free (800) 523- 1510
fax no. [phone]
Gas supply
requirements
Fire Hazard
l These dryers must be connected
to a regulated gas supply.
Failure to do so could result In hlgh-
pressure gas release, resultlng In a
tire or exploslon.
l Have L.P.gas checked by a
qualltled person betore lnstalllng
the dryer. The L.P.gas supply must
not exceed a pressure ot 13”
water column.
l New tlexlble tublng should be
used. Reuslng old, tlexlble tublng
mlght result In possible leaks or
tire hazard.
Failure to tallow these lnstructlons
could result In tlre or exploslon.
OBSERVEALLGOVERNING CODES
AND ORDINANCES.
n This installation ust conform
with American Nationa Standard,
National Fuel Gas Cod ANSI Z223.V
latest edition, and all lo al codes and
ordinances. 4
B H The design of this dryer has
been certified by the A
Association for use at a itudes up to
10,000 feet above sea I vel at the
B.T.U. rating indicated n the
adjustments are not re
elevation. i
erican Gas
model/serial plate. Bur r input
uired when
the dryer is operated u to this
your local service corn
the particular type o
Burner information wi
see your dealer.
D n These drvers are/ shipoed for
use with NATURAL GAS. hey are
certified by the Americ n Gas
Association for manufa tured, mixed
and L.P. (propane and i utane) gases
with appropriate conv&sion. No
attempt shall be made o convert the
appliance from the gas specified on
the rating plate for use ith a
different gas without c suiting the
serving gas supplier. Co verslon must
1
be done by a qualltled ervlce
technician. Gas conver Ion klt part
numbers are llsted on t e gas valve
burner base.
supply line is more than
usage, 3/8-inch, appro
F
n If local codes and ordinances
permit, it is recommended that new
flexible metal tubing, design-certified
by the American Gas Association, be
used for connecting the dryers to the
gas supply line. (The gas feed pipe,
which extends through the lower rear
of each dryer, is provided with 3/8-
inch male pipe thread.)
shutofl valve
G
n The supplv line shall be
equipped with a shutoff valve. This
valve should be located in the same
room as the dryers and should be in a
location that allows ease of opening
and closing. Do Not block access to
shutoff valve.
main gas supply line, a
combination of fittings must be
used to obtain an in-line connection
to the dryers.
n Make sure lower edges, back
and sides of the cabinet are free of
obstructions to permit adequate
clearance of air openings for
combustion air. See ‘Recessed area
and closet installation instructions” for
minimum spacing requirements,
J
n For ease of installation,
operating and servicing (if ever
needed), adequate space should be
provided around the dryers.
K
n A l/&inch, NPT plugged
tapping, accessible for test-gauge
connection, must be installed
immediately upstream of the gas
supply connector to the dryers.
The dryers and their individual shutoff
valves must be disconnected from
the gas supply piping system during
any pressure testing of that system at
test pressures in excess of l/2 psig
(3.4 kPa).
The dryers must be isolated from the
gas supply piping system by closing
their individual manual shutoff valves
during any pressure testing of the gas
supply piping system at test pressures
equal to or less than l/2 psig
(3.4 kPa). Page 3

L n If the dryers are installed in a
confined area such as a bathroom or
closet, they must be exhausted to the
outside and provision made for
enough air for combustion and
ventilation. (Check governing codes
and ordinances. Also refer to the
section of this instruction covering
“Recessed and closet installations.“)
Elect&al
requlremen s
f
outlet, have a pro
Installed by a quall
electrlclan.
l Do Not use an exte
properly grounded
death.
It codes permit and
groundlng wire Is us
recommended that a q
electrlclan determlne t
A 120-volt &I-Hz AC-
Rebrdmended grounding
For your personal safety, these dryers
must be grounded. Each dryer is
equipped with a power supply cord
having a 3-prong grounding plug. To
minimize shock hazard, the cords
must be plugged into mating 3-prong
grounding-type wall receptacles,
grounded in accordance with
National Electrical Code ANSVNFPA
70 - latest edition, and all local
codes and ordinances. If a mating
wall receptacle is not available, it is
the personal responsibility and
obligation of the customer to have a
properly grounded, 3-prong wall
receptacle installed by a qualified
technician. See Figure 1.
Spron8groun ng-type
wall receptacle 1
J-Drona
gioundlng
Plug
w
/ 4 t
I
grounding
PoysuPPtY prong
Figure 1
Page 4

Exhaust
requirements
Fire/Health Hazard
l Do Not use non-metal, flexible
duct.
l Do Not use metal duct smaller
than four Inches In diameter.
l Do Not use exhaust hoods wlth
metal latches.
BCheck that exhaust system Is not
longer than speclfled. Exhaust
system longer than speclfled will:
- Accumulate Ilnt.
- Shorten the life of the dryer.
- Reduce the petformance,
resulting In longer drying times
and Increased energy usage.
Iallure to kii0w speclflcatlons may
‘esult In a IIre.
bDo Not exhaust dryers Into a
chimney. turnace cold alr duct,
attlc or crawl space, or any other
duct used for ventlng.
1Clean the exhaust system every
other year.
) Do Not Install flexible duct In
enclosed walls, celllngs or floors.
iccumulated llnt could result In a
Ire or cause molsture damage.
1Exhaust dryers outslde to prevent
exposure to substances In gas
duels and combustion which may
be harmtul to your health.
.he molsture and llnt Indoors may
cause:
. FIREHAZARDfrom llnt collected In
dryer.
. Molsture damage to woodwork,
turnlture, palnt, wallpaper, carpet,
etc.
nHousecleanlng problems and
possible health problems.
:allure to tallow these lnstructlons
:ould result In tlre damage or
3ersonal Injury.
Exhaust materials are not
supplied.
Four-Inch metal exhaust duct is Four-Inch metal exhaust duct is
required. Plan installation to use therequired. Plan installation to use the
fewest number of elbows and turns.fewest number of elbows and turns.
Allow as much roo ossible when
The external exhaust
routed up, down
requirements are
length of the exhaust
exhausted out the sid
feet with two externa
hood.
Rear exhaust: The ma
the exhaust system
If dryers are Installed In a conflned
area such as a bedroom, bathroom
or closet, they must be exhausted to
the outside and provision must be
made for enough air for combustion
and ventilation. (Check governing
codes and ordinances. Also refer to
the ‘Recessed area and closet
installation instructions,” Page 8.)
An exhaust hood should cap the
exhaust duct to prevent exhausted
air from returning into the dryers. The
outlet hood must be at least 12
inches from the ground or any object
that may be in the path of the
exhaust.
Four-Inch outlet hood Is preterred.
However, a 2-l/2-inch outlet exhaust
hood may be used. (A 2-l/2-inch
outlet creates greater back pressure
than other hoods.)
A maln exhaust duct can be used for
exhausting a group of dryers. Main
exhaust duct should be sized to
remove 200 CFM of air per dryer.
Large-capacity lint screens of proper
design may be used in the main
exhaust duct if checked and
cleaned frequently. The room where
the dryers are located should have
make-up air equal to or greater than
the CFM of all the dryers in the room.
Thls chart applies only [to Indlvldually
( /$fya. *tie
exhausted unlts. I 4
MAXIMUM LENGTH OF I-INCH DIA TER RIGID METAL DUCT
MAXIMUM LENGTH OF 4.lNCH DIAM ER FLEXIBLE METAL DUCT
available from your Wb irlpool parts
distributor.
exceed 0.6 inches of
airtlow - main colktorduct -
Back-draft damper klts (Part No.
3391910) are available from your
Whirlpool dealer and should be
installed in each dryer’s exhaust duct
to prevent exhausted air from
returning into the dryers and to keep
the exhaust balance within the main
exhaust duct. Unobstructed air
openings are required.
Each exhaust duct should enter the
main duct at an angle pointing in the
direction of the airflow. Ducts
entering from the opposite side
should be staggered to reduce the
exhausted air from interfering with the
other ducts.
The maxlmum angle of each duct
entering the main duct should be no
more than 30”.
Page 5

Product Damage
Keep alr openlngs tree ot dry-
cleaning fluld fumes. Fumes
create acids which, when drawn
through the dryer heatlng unlts,
can damage dryers and loads
being dried.
A clean-out cover should be located
on the main exhaust duct for
periodically cleaning the exhaust
system.
An exhaust hood should cap the
outside end of the main duct to
prevent exhausted air from returning
to the dryers. If an exhaust hood
cannot be used, the outside end of
the main duct should have a sweep
elbow directed downward. If the
main duct travels vertically through
the roof rather than through the wall,
install 180” sweep elbow on the end
of duct at least 2 feet above the
highest part of the building. The
opening wall or roof shall have a
diameter l/2 inch larger than the
exhaust duct diameter. The exhaust
duct should be centered in the
opening.
exhaust
hood or hortzontal duct
2 tl. min. 180’
maln collector
Do Not install screening cap over end
of duct.
Page 6
Exhaust du t
connection
electrical shock or k
Failure to do so may r suit In
sonal Injury.
Electrlcal Shock Hazard
Disconnect both pow r supply
cords before maklng hese
changes.
be exhausted through
Next, determine the le th of exhaust
To connect exha
straight out the b
exhaust hoods or main
To connect exha
through the right
1. Remove access pa
other access panel.
Personal Injury Hazard
Wear gloves to protect hands tram
sharp edges that may be present.
Failure to do so may result In
personal Injury.
2. Remove the duct tape from the
internal exhaust duct and the straight
duct. Repeat for the other dryer.
3. Remove the screw from the duct
clip that attaches the straight duct to
the back of the cabinet. Depress the
clip to remove the straight duct using
a twisting motion through the rear
exhaust opening. Repeat for the
other dryer.
4. Reach through the rear exhaust
opening and depress center of tabs
on the plastic opening cover on the
side you want to exhaust through.
Remove the cover. Repeat for other
dryer.
90” elbow
(Not supplied
with unit.)
tape
plain a
/ joint
end ,,LL-
5. Attach a three- or four-section
elbow to the straight duct using duct
tape. Repeat with the other elbow
and straight duct.

f
internal
exhaust duct
6. Insert elbow end of duct pieces
through the side opening. Reach
through the access panel opening
and attach elbow to the internal
exhaust duct. Check the length of
straight duct extending out the side
of the cabinet. If duct extends too far
to make the exhaust duct
connection, mark a line around the
straight duct one inch out from the
cabinet. Remove the duct and elbow
and cut the straight pipe to the
length needed. Reinsert the duct
pieces. Use duct tape to connect the
elbow to the internal exhaust duct.
Repeat for the other dryer.
7. Insert the plastic cover into the
rear exhaust opening.
8. Replace the access panels.
9. Use duct tape to seal all joints.
To connect exhaust duct
through the bottom of the
lower dryer only -
Note: You must use a three-section
elbow to connect exhaust duct
through the bottom of the lower
dryer.
1. Check that the legs extend one
inch from the bottom of the dryer.
2. Remove the lower dryer access
panel by releasing the two locking
clips with a small, flat-blade
screwdriver. The clips are located
four inches in from each side of the
access panel, Lift access panel off
the bottom clips and set aside.
3. Remove duct tape f m internal
exhaust duct and the s
t aight duct.
4. Remove the screw fr m the duct
clip that attaches the s aight duct to
the back of the cabine Depress the
clip and remove the str
using a twisting motion 1
ight duct
rough the
rear exhaust opening. i
5. Measure from the
straight duct and mark
Cut the straight duct
6. Reach through the r
opening and depress c
on one of the side,
covers. Remove the co
7. With a Phillips screw river, reach
through the rear exhau opening
and remove the screw
%
at attaches
the cover to the dryer se. Carefully
remove the cover and rew through
the rear exhaust openin .
Floor Damage
Slide dryers onto cardboard or
hardboard betore moving across
tloor.
Failure to do so may cwse damage
to tloor coverlng.
8. Move dryers into
position. Reach throug
opening and mark the
9. Cut opening through the floor.
10. Push the four-inch, straight duct
through the rear exhaust opening
and onto the internal duct as far as it
will go.
+
a
front
L3
Of
I dryer
I.--
11. Insert the elbow through the rear
exhaust opening. Insert elbow into
the bottom exhaust opening.
/iah I
I I
L--
of
dryer
12. Slide the straight duct into the
elbow approximately one inch. Use
duct tape to seal both Jolnts.
screw head
(fastens against
edge of cabinet)-
cabinet
rear
13. Insert the
bottom exhaust
cover through the
side exhaust
opening. Put the
cover over the rear
c
tab
exhaust opening bottom
with the tab
of dryer
pointing down to
bottom of dryer. t
Insert screw through
the hole in the cover that is on the
inside of the cabinet. Tighten screw.
14. Replace the side exhaust cover.
15. Move the dryers into operating
position. Check that the elbow is
through the bottom exhaust opening.
Replace the access panel.
16. Connect elbow to exhaust duct.
Then connect exhaust duct to
exhaust hood or main exhaust. Use
duct tape to seal all joints.
Page 7

Recessed area and
closet installations
Fire/Health Hazard
Exhaust dryers to the outslde to
prevent exposure to substances In
the gas tuels and combustion
byproducts which may be harmful
to your health.
Failure to do so may result In a tlre
or health hazard.
Thls appliance may be Installed In a
recessed area.
The installation spacing is the
minimum allowable. Additional
spacing should be considered for
ease of installation, servicing and
compliance with local codes and
ordinances.
If closet door is installed, the minimum
unobstructed air openings in the top
and bottom are required. Door must
have two centered openings as
illustrated. Both openings must
provide a minimum of 72 square
inches of unobstructed airflow as
shown. Louvered doors with
equivalent air openings are
acceptable.
FORCLOSETINSTALLATIONS,TO
PREVENTLARGEAMOUNTS OF LINT
AND MOISTUREFROM
ACCUMULATING, TO MAINTAIN
DRYING EFFICIENCY,AND TO PREVENT
EXPOSURETO POSSIBLEHEALTH
HAZARDS,DRYERSMUSTBE
EXHAUSTEDOUTDOORS.
4
0”
Additional
clearances may
be requlrsd for
wall, door and
floor moldings If
external exhaust
elbow Isused.
1
810
i ___ -
Side view
O”-D
Additional
;p;lza
for exhaust
Closet vi
-4
w
+
nn
Ill
’ II
0
Additional
clearances for
wall, door and
1 floor moldings
may be
c
required.
7”
Closet door
Opening is
48’sq. in:’
I
minimum for
closet door.
Louvered
door with
equivalent air
24’sq. i
oljenings is
acceptable. :
~,
Fr+nt view
Companion appliance spacing
should be considered.
No other tuel-burnlng a pllance may
be Installed In the same1 closet.
Product dimensiohs
Slde vlew
approx.
r
Rear view ,
Im ex’haust
exhaust
To than e to a
%30- or 6 -minute
timing cam
Electrlcal Shock Hazard
Disconnect both power supply
cords tram the electric power
supply betore maklng these
changes. Change tlmlng cams
betore completing electrlcal
connectlon.
Failure to tallow these lnstructlons
may result In electrlcal shock or
personal Injury.
Each dryer is equipped with a 45
minute timer cam that provides 4.5
minutes of drying time when
activated by the coin slide.
You can install the Dminute or &I-
minute timing cam (shipped with
each dryer) as follows:
1. Unlock control panel. Lift up and
rotate out from cabinet. Control
panel will still be attached to cabinet.
2. Reach into control panel area. Use
a Phillips screwdriver to loosen (but
not remove) timer mounting bracket
screw. Lift up to remove timer
assembly and bracket from cabinet.
\\
ratchet tooth
I.
4
timing cam
3. Turn the timing cam by hand until
the ‘V-shaped notch lines up below
the ratchet tooth.
Recessed Wontvlew
Page 8

timing cam
ratchet tooth I f
m-1
Line up notch
to clear
ratchet tooth.
4. Insert a narrow, flat-blade
screwdriver under the timing cam
near the clock shaft. Gently lift cam
straight up and off shaft making sure
that the “V”-shaped notch clears the
ratchet tooth.
5. Place new cam (hub side down)
over clock shaft, Line up flat side of
shaft with flat side of cam hole.
Check that drive lug is in place.
6. Turn cam until “V-shaped notch
lines up with ratchet tooth.
7. Press cam down in place on motor
shaft. Make sure that “V-shaped
notch clears the ratchet tooth.
8. Reattach the timer bracket
assembly; tighten the screws.
9. Repeat steps for other timer.
10. Close and lock the control panel.
Now start...(
With dryers in lauddry area.
Check that each leg is bpproximately
1 inch from base.
2.
Wipe the interior of the
thoroughly with a dam
3.
Install coin vaults and lo’ ks (not
supplied) into meter ca e openings.
f
4.
Install control panel lock and key (not
supplied)
Electrlcal Shock
5.
If you wish to change th 45-minute
dryer timing cams to eit 1er 30- or 60-
minute timing cams,
to a 3C- or 60-minute
Pages 8 and 9. Complet
steps given in that secti
going to Step 6.
Electrlcal Shock azard
Disconnect electrlcal
i
wer at the
service panel (ruse bo or clrcult
breaker box).
Failure to do so could r sult In
serlous Injury or death.
Open control panel and rest it on the
bottom edge of the opening. Attach
slide extension (with flange pointing
down) to one of the coin-slide
mechanisms. Insert the coin-slide
mechanism through the opening to
the left of the control panel.
Secure coin-slide mechanism from
inside the control panel using the
3/l 6” bolt and washer supplied. Install
coin box.
8.
Repeat Steps 6 and 7 for the other
coin-slide mechanism. Close control
panel.
Jl
i
9.
Insert top of wire guard into holes on
each side of the coin-slide
mechanism. Insert screws through
hooked ends of guard and tighten.
Repeat for other wire guard.
Page 9

Remove the red caps from the gas
pipes.
11 n
Connect gas supply to each dryer.
Use pipe-joint compound resistant to
the action of Natural and L.P. gas for
gas connections,
rhutofl valve
12.
Open the shutoff valves in the gas
supply lines.
Fire Hazard
Do Not use an open flame to test
tar leaks from gas connections.
Checking for leaks wlth a flame
may result In a flre or explosion.
13 w
Use a brush and liquid detergent to
test all gas connections for leaks,
Bubbles around connections will
indicate a leak. If a leak appears,
shut off gas valve controls and adjust
connections. Then check
connections again, NEVERTESTFOR
GAS LEAKSWITHA FLAME. Close the
access panels.
All connectlons must be wrench-
tlghtened.
14.
Plug power supply cord
grounded outlets. Turn (
power supply.
Floor Dama
Slide dryers onto card
hardboard before mo
rloor.
Failure to do so may r(
damage to floor cove
Move unit to its pc
location.
15.
Turn one dryer on to rer
the gas supply line. Usin
cycle (not the air cycle:
run for at least five mint
burner does not ignite c
feel no heat inside the (
the dryer for five minute
all supply valve controls
position and that the pc
cord is plugged in. Repc
minute test.
I
into
I electrical
nm
8
‘oard or
Ing across
;I
,
‘1
5
b
\‘I
EC
r
31
r<
(1
1,
I 1
I-
:I
I’.
;(
:\ ,
I
5ult In
w.
rmanent
ove air from
a full heat
let the dryer
es. If the
Id you can
yer, shut off
Check that
are in “ON”
tier supply
Jt the five-
16
n
Checklevelness of dryers by placing
a carpenter’s level on top of the
dryers or collar, first side to side, then
front to back. If dryer is not level,
adjust the front legs up or down.
Make the final check with the level.
17
WTO exhaust the dryers, see
‘Exhaust requirements” and “Exhaust
duct connection,” pages 5 to 7.
Personal InJury Hazard
To prevent tlpplng, tether bracket
must be secured to wall studs or
concrete wall.
Failure to do so could result In
personal Injury.
Tether bracket. located atTether bracket, located at
rear of the top dryer.rear ot the top ‘dryer.
18.
Attach both ends of tether located at
the rear of the top dryer to a secured
2x4.
Page 10

Check to make sure you have all your
tools.
The installation is now
complete.
r
I
16. 18.
I
(with step
I
.
17.
10.11.
14.
17.
10.11.
Page 11

If dryers do not
operate properly.. .
Check the folIowIng to be sure that:
1. Electrical supply is connected.
2. Circuit breakers are not tripped or
fuses blown,
3. Doors are closed.
4. Timer has been actuated.
5. Controls are set in a running or
‘ON” position.
6. Gas shutoff valves are open both
on dryer and supply line.
to a
...
Floor Dama 8
Slide dryers onto card oard or
hardboard before mo Ing across
rloor.
Failure to do so may r
i suit In
damage to floor cove ng.
l Tape doors. i
l Disconnect gas pipe nd fittings
gas supply
line. Tape end of drye gas pipes.
l Shut off electric suppl to dryers.
l Disconnect power su ply cords.
Tape securely to drye
l Shut off the gas suppl valves in the
gas supply line.
from dryer and cap
l Tape the drums to the front panel.
l Adjust leveling legs all he way in.
Before installing dryers i a new
location, check with yo r gas supplier
or dealer to see that yo r dryer is
1
equipped with the corr ct burner for
the particular type of g s in your new
building. Burner informa ion may be
found on the rating pla in the door
well of the dryer.
If you need
assistance...
The Whirlpool Consumer Assistance
Center will answer any questions
about operating or maintaining your
dryers not covered in the Installation
Instructions. The Whirlpool Consumer
Assistance Center is open 24 hours a
day, 7 days a week. Just dial l-(800)
253-1301 - the call is free.
When you call, you will need the
dryer model number and serial
number. Both numbers can be found
on the serial/rating plate located in
the door well behind the dryer door
and on the front of the opening.
Printed on recycled paper
10% post consumer waste/
50% recovered materials.
Part No. 3395314 Rev. E
0 1994 Whirlpool Corporation Prepared by Whirlpool Corporation,IBenton Harbor, Michigan 49022 Printed in U.S.A.