Whirlpool LE8600XW User manual

vi&l 01
4a
Use& Care’Guide
Cycle control knob
I
Temperature selector
I
Start button
Lint screen
LARGECAPACITY
AUTOMATICDRYERS
LE8600xw LG86owv

Contents
Page
Important Safety
Instructions. . . . .
Additional safety instructions
and your responsibilities
Operating Instructions
Starting your dryer
The automatic cycles
Timed drying
Using fluff air . .
Caring For Your Dryer
Cleaning the lint screen . .
Cleaning the dryer interior
Lint removal
If You Need Service Or
Assistance. .
Whirlpool Automatic
Dryer Warranty.
01990 Whirlpool Corporation
3
3
4
6
7
7
8
8
9
10
12
If your dryer has a Consumer Buy
Guide label, remove it. It will be easier
to remove before the dryer is used.
To remove any remaining glue:
l Rub briskly with thumb to make a ball,
then remove.
or
l Soak area with liquid hand dishwash-
ing detergent before removing glue
as described above.
Do not use sharp instruments,
rubbing alcohol, flammable fluids or
abrasive cleaners. These can damage
the finish. See “Important Safety
Instructions” on page 3.
NOTE: Do not remove any permanent
instruction labels inside the dryer.
You should wipe out the dryer drum
with a damp cloth before using to
remove dust from storing or shipping.
Thank you for buying a Whirlpool
appliance. Please complete and mail
the Owner Registration Card provided
with this product. Then complete the
form below. Have this information ready
if you need service or call with a
question.
l Copy model and serial numbers
from plate (on the frame behind the
door) and purchase date from sales
slip.
l Keep this book, the Dryer Guide and
the sales slip together in a handy
place.
Model Number
Serial Number
Purchase Date
Service Company Phone Number
FOR YOUR SAFETY
If you smell gas:’
1. Open windows.
2. Don’t touch electrical
switches.
3. kFeguish any open
.
4. Immediately call your
gas supplier.
FOR YOUR SAFETY
Do not store or use gas-
oline or other flammable
vapors and liquids in the
vicinity of this or any
other appliance. The
fumes can create a fire
hazard or explosion.

ImportantSafetyInstructions
To reduce the risk of fire, electrical shock, or
injury to persons when using your dryer, follow
basic precautions, including the following:
l Read all instructions before
using the dryer.
l You are responsible for mak-
ing sure that your dryer is in-
. NEVER dry items cleaned, stalled, repaired and has parts
washed, soaked in or spotted with replaced by a qualified person.
wax, paint, gasoline or flammable
fluids in the dryer. The fumes can
l Use only fabric softeners specifi-
create a FIRE HAZARD or cally labeled as not being harmful
EXPLOSION. ALWAYS hand to the dryer.
launder and air dry fabrics contain- . FIRE HAZARD and DAMAGE to
ing these materials. materials can result from:
l NEVER allow children to operate, -drying rubber, rubber-like and
play with or crawl inside the dryer. heat sensitive materials with heat.
Close supervision of children is -allowing lint build-up inside the
necessary when the dryer is used dryer or exhaust system. Clean-
near children. ing should be done periodically
l DO NOT reach into a dryer if the by a qualified person.
drum is moving.
l Clean lint screen before or after
each load.
l When discarding an old dryer,
ALWAYS remove the door to
l DO NOT let dust, lint, paper, rags,
prevent accidental entrapment. chemicals, etc. pile up around or
l DO NOT install or store dryer under the dryer.
where it will be exposed to the
l Dryer must be electrically
weather. grounded. See the Installation
Instructions.
l DO NOT tamper with the controls.
- SAVE THESE INSTRUCTIONS -
Additionalsafetyinstructionsandyourresponsibilities
l NEVER operate the dryer if: - is properly installed and leveled
- it is not working right (i.e. noisy, too hot). on a floor that can support the
- it is damaged. weight in a well ventilated room.’
-parts are missing (i.e. door latch). - is located in an area where the
-all panels are not in place. temperature is above 45°F (7.2%).
-the lint screen is loose, damaged - is connected to the proper outlet
or missing. and electrical supply.*
l ALWAYS shut off the gas valve - is properly connected to fuel and
before leaving on vacation if you have exhaust systems.’
a qas dryer. -is not installed against drapes or
l ALWAYS unplug the power supply
cord or turn off electrical power before
attempting to service the dryer. Shut
off GAS VALVE if you have a gas dryer.
l You are responsible for making
sure that your dryer:
-is properly maintained.
curtains.’
- is used only for jobs normally
expected of home clothes dryers.
- is not used by anyone unable to
operate it properly.
*See the Installation Instructions for
complete information.
3

OperatingInstructions
Startingyourdryer
Be sure to refer to the chart below and the Dryer Guide for proper sorting, loading
and control setting information before starting it.
SUGGESTED SUGGESTED
TYPE OF LOAD CYCLE TEMPERATURE
Cottons and linens
EXTRA HEAVY - Bedspreads, mattress
pads, quilts
HEAVYWEIGHT-Towels, jeans,
corduroys, work clothes
MEDIUMWEIGHT - Sheets, pillowcases,
cotton, underwear, diapers
LIGHTWEIGHT - Batistes, organdies,
lingerie
AUTOMATIC PERM’T PRESS
REGULAR HEAVY HIGH
Permanent press, synthetics
and blends
HEAVYWEIGHT-Work clothes, jackets, AUTOMATIC PERM’T PRESS
raincoats PERMANENT PRESS HEAVY HIGH
MEDIUMWEIGHT- Shirts, play clothes,
sheets, slacks
LIGHTWEIGHT - Lingerie, blouses,
dresses
Knits
HEAVYWEIGHT-Cottons, rayons,
blends, T-shirts, slacks, shirts
LIGHTWEIGHT - Synthetic (polyester,
acrylic, etc.) and blends, lingerie,
blouses, dresses
AUTOMATIC PERM’T PRESS
PERMANENT PRESS HEAVY HIGH
KNITS GENTLE
LOW
Delicate fabrics
Sheer curtains (2 or 3 panels), gauze, AUTOMATIC KNITS GENTLE
Rubber, plastic,
heat-sensitive fabrics
FOAM RUBBER-Pillows, bras,
stuffed toys
PLASTIC - Shower curtains, tablecloths
RUBBER-BACKED RUGS
TIMED DRYING
20-30 MIN.?. FLUFF AIR
20-30 MIN.?.
40-50 MINS.
OLEFIN. POLYPROPYLENE, 15-20 MINS
SHEER NYLON
DO NOT OVERDRY. Overdrying can cause shrinkage, static cling, and damage
some fabrics.

1. Select a cycle by turning the Cycle
Control Knob either way. Stop when
the indicator on the knob’s outer ring
points to the cycle and setting you
want. See pages 6 and 7 for
further cycle information.
2. Set the Temperature Selector on
the desired temperature settings.
3. Push the Start Button to start
the dryer.
4. To stop and restart the dryer:
l Open the door or turn the Cycle Con-
trol Knob to OFF to stop the dryer.
l Close the door, select a cycle (if nec-
essary) and push the Start Button to
restart the dryer.
The Cycle Control Knob should point
to an OFF area when the dryer is not in
use. If the dryer is stopped before the
cycle is finished, turn the Cycle Control
Knob to an OFF area.

Operating Instructions
Continued
Theautomaticcycles
The automatic cycles allow you to
select the degree of dryness you prefer
for the clothes being dried.
The automatic DRY-MISER@ control
is a thermostat that senses the air
temperature. The dryer automatically
shuts off when the selected dryness is
reached.
The Cycle Control Knob will not move
until the clothes load is almost dry, or
the Cool-Down portion of the cycle has
been reached. After the Cool-Down
portion is complete, the Cycle Control
Knob automatically moves to an OFF
area and tumbling stops.
to handle.
For the first few loads, set the Cycle
Control Knob to point to the * in either
automatic cycle. When the dryer stops,
feel the dried items.
l If items are drier than you like, use a
setting to the right of the * the next
time you dry a similar load.
l If items are not as dry as you like, use
a setting to the left of the * the next
time you dry a similar load.
NOTE: Overdrying can cause
shrinkage, static cling and damage to
some fabrics.
6

Timeddrying
Use the TIMED DRYING cycle for any
load you want to dry by time. This cycle
is designed for small loads, large bulky
items or items to be fluffed or dusted
with the FLUFF AIR heat setting.
l Turn the Cycle Control Knob to the
number of minutes you want from
10 to 60.
l For a damp dry, turn the Cycle Control
Knob to 30 minutes or less.
The last 5 minutes of this cycle
are without heat to help make the load
easier to handle.
UsingFLUFFAIR
Tl
he dryer does not heat when the
Temperature Selector is set on FLUFF
AIR. This setting can be used to fluff
or air dry bedding, plastic tablecloths,
foam rubber pillows, stuffed toys,
sneakers, etc.
Fire Hazard
Do not dry plastic or rubber items
with heat. Use FLUFF AIR setting,
or line dry. Failure to do so could
result in fire or damaged items.
1. Turn the Temperature Selector to
FLUFF AIR.
2. Turn the Cycle Control Knob to the
number of minutes you want in the
TIMED DRYING cycle.
3. Push the Start Button.

CaringForYourDryer
Cleaningthelintscreen
The lint screen is located under a lid on top of the dryer. Clean it before each
load. A screen blocked by lint can increase drying time.
Electric Shock Hazard
Unplug the power supply cord
or turn off the electrical power
before cleaning the interior.
Failure to do so could result in
electrical shock or injury.
1. Open the lid and pull the lint screen
straight out.
2. Roll lint off the screen with your
fingers. Do not rinse or wash the
screen. Wet lint is hard to remove.
3. Push the lint screen firmly back into
place and close the lid.
Cleaningthedryerinterior
Garments which contain unstable dyes,
such as denim blue jeans or brightly
colored cotton items, may discolor the
dryer interior. If the interior is discolored,
clean with one of the following methods
to avoid staining later load items.
8

Powdered laundry detergent
Make a paste with detergent and very
warm water. Apply paste to a soft cloth
and scrub area until all excess dye is
removed. Wipe thoroughly with a damp
cloth. Tumble a load of rags to dry.
-OR-
Liquid household cleaner
Apply to stained area. Rub with a cloth
until all excess dye is removed. Tumble
a load of rags to dry.
To clean dryer exterior, wipe with a
sol-l, damp cloth.
Electric dryer
Igniter _ Funnel ~-
Lintremoval
Lint can gather inside the dryer and
create a FIRE HAZARD. This lint
should be removed at least every
2 to 3 years, or more often,
depending on dryer usage.
Electrical Shock and
Personal Injury Hazard
l Unplug the power supply cord
or turn off the electrical power
before removing lint.
l Do not put hands inside the
cabinet.
l Make sure the dryer is cool.
Failure to do so could result in
electrical shock, injury or
damage.
Gas dryer
Cleaning should be done only by a
qualified person.
1. Remove back panel (electric) or
lower access panel (gas).
2. Avoid damaging wires, thermostats,
funnel or igniter.
3. Remove lint from boxed-in area with
a sofl brush or vacuum cleaner.
4. Replace panel; reconnect and
relevel the dryer.
9

IfYouNeedServiceOrAssistance
Wesuggestyoufollow
thesesteps:
1. Before calling for assistance...
Performance problems often result from
little things you can find and fix yourself
without tools of any kind.
If your dryer does not run:
l Is the power supply plugged into a live
circuit with the proper voltage?
l Is the door closed tightly?
l Did you push the Start Button?
l Have you checked your home’s main
fuses or circuit breaker box?
If your dryer does not heat:
l The FLUFF AIR cycle ISwithout heat.
l The last minutes of heat settings are
without heat.
l Is the gas turned on? If not, turn the
Cycle Control Knob to OFF Turn on
gas. Wait 5 minutes. Reset controls
and star-t.
l An electric dryer circuit uses 2 break-
ers or 2 fuses. If one breaker is tripped
or one fuse is blown, the dryer may
run, but not heat.
If drying time seems too long.
l Is the lint screen clean? See page 8
for cleaning instructions.
l See the Dryer Guide.
2. If you need assistance:..
Call Whirlpool COOL-LINE@
service assistance telephone
number. Dial free from anywhere
in the U.S.:
l-800-253-1301
and talk with one of our trained consul-
tants The consultant can instruct you in
how to obtain satisfactory operation
from your appliance or, if service is nec-
essary, recommend a qualified service
company in your area.
If you prefer, write to:
Mr. Donald Skinner
Director of Consumer Relations
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
Please include a daytime phone
number in your correspondence.
3. If you need service’...
%&I 46^
Whirlpool has a
01
9~ nationwide network
of authorized
sEnvrcE WhirlpoolSM service
companies.
Whirlpool service technicians are trained
to fulfill the product warranty and provide
after-warranty service, anywhere in the
United States. To locate the authorized
Whirlpool service company in your area,
call our COOL-LINE@ service assistance
telephone number (see Step 2) or look in
your telephone directory Yellow Pages
under:
APPLIANCES - HOUSEHOLD - ELECTRICAL APPLIANCES -
MAJOR-SERVICE A REPAIR MAJOR-REPAIRING A PARTS
OR
WASHING MAWINES. DRYERS
A IRONENS - SERVICING
10

4. If you need FSP’
replacement parts:..
FSP is a registered trademark of
Whirlpool Corporation for quality parts.
Look for this symbol of quality when-
ever you need a replacement part for
your Whirlpool appliance. FSP replace-
ment parts will fit right and work right,
because they are made to the same
exacting specifications used to build
every new Whirlpool appliance.
To locate FSP replacement parts
in your area, refer to Step 3 or call the
Whirlpool COOL-LINE service
assistance number in Step 2.
5. If you are not satisfied with
how the problem was solved’...
l Contact the Major Appliance
Consumer Action Panel (MACAP).
MACAP is a group of independent
consumer experts that voices con-
sumer views at the highest levels of
the major appliance industry.
l Contact MACAP only when the
dealer, authorized servicer or
Whirlpool have failed to resolve
your problem.
Major Appliance Consumer
Action Panel
20 North Wacker Drive
Chicago, IL 60606
l MACAP will in turn inform us of
your action.
*When requesting assistance, please
provide: model number, serial number,
date of purchase, and a complete
description of the problem. This infor-
mation is needed in order to better
respond to your request.

Whirlpool”AutomaticDryerWarranty
DROOl
LENGTH OF WARRANTY 1 WHIRLPOOL WILL PAY FOR 1
FULL ONE-YEAR
WARRANTY
From Date of Purchase
FSP@ replacement parts and repair labor to
correct defects in materials or workmanship.
Service must be provided by an authorized
Whirlpools’+’ service company.
WHIRLPOOL WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation of the dryer.
2. Instruct you how to use the dryer
3. Replace house fuses or correct house wiring or plumbing.
4. Replace light bulbs.
B. Repairs when dryer is used in other than normal, single-family
household use.
C. Pick up and delivery. This product is designed to be repaired in
the home.
D. Damage to dryer caused by accident, misuse, fire, flood, acts of
God or use of products not approved by Whirlpool.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation
of incidental or consequential damages so this limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Outside the United States, a different warranty may apply. For details, please
contact your franchised Whirlpool distributor or military exchange.
If you need service, first see the “Service and Assistance” section of this book.
After checking “Service and Assistance;’ additional help can be found by calling
our COOL-LINE@ service assistance telephone number, l-500-253-1301, from
anywhere in the U.S.
Part No. 3391360
01990 Whirlpool Corporation Printed in U.S.A.