Whirlpool Gladiator GarageWorks Extra Large GearBox... User manual

EXTRA LARGE
GEARBOX CABINET
Assembly Instructions
AMARIO EXTRA GRANDE
CON ESTANTES PARA
HERRAMIENTAS
Instrucciones de ensamblaje
TRÈS GRANDE
ARMOIRE À OUTILS
Instructions d'assemblage
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
CABINET/LOCKER SAFETY......................... 2
PARTS ............................................................ 2
ASSEMBLY INSTRUCTIONS........................ 2
Cabinet Use Requirements...................... 2
Unpack Cabinet Parts................................. 2
Assemble Cabinet....................................... 3
Attach Back Panels..................................... 3
Install Leveling Legs.................................... 4
Install Shelves.............................................. 4
Install Doors ................................................ 5
Complete Assembly.................................... 5
ACCESSORIES .............................................. 5
WARRANTY ................................................... 6
SEGURIDAD DEL ARMARIO ....................... 7
PIEZAS ........................................................... 7
INSTRUCCIONES DE ENSAMBLAJE.......... 7
Requisitos de uso del armario................. 7
Desempaque las piezas del armario .......... 8
Ensamble el armario ................................... 8
Fije los paneles posteriores ........................ 8
Instalación de las patas niveladoras........... 9
Instalación de los estantes ......................... 9
Instalación de las puertas......................... 10
Complete el ensamblaje ........................... 10
ACCESORIOS.............................................. 10
GARANTÍA ................................................... 11
SÉCURITÉ DE L’ARMOIRE.........................12
PIÈCES..........................................................12
INSTRUCTIONS D'ASSEMBLAGE .............12
Spécifications d'utilisation de l'armoire ....12
Déballage des composants de l'armoire ..13
Assemblage de l'armoire...........................13
Fixation des panneaux arrière ...................13
Installation des pieds de réglage
de l'aplomb ................................................14
Installation des étagères............................14
Installation des portes ...............................15
Fin de l’assemblage...................................15
ACCESSOIRES.............................................15
GARANTIE ....................................................16
W10174899A
IT'S TIME TO RETHINK THE GARAGE.®
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
LE GARAGE REPENSÉ.™

2
CABINET/LOCKER SAFETY
PARTS
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
P2
P5
P5
P5
P3
P6
P7
P1
P1
P8
P4
P4 P4
P8
P8
P8
P8
P8
F1 F2 F3b F4
F5 F6 F9

3
ASSEMBLY INSTRUCTIONS
Cabinet Use Requirements
■Intended for use in a garage.
■Maximum weight limit is 50 lbs (22.7 kg) for each shelf.
■Maximum weight limit is 250 lbs (113.6 kg) for the cabinet.
Unpack Cabinet Parts
1. Remove and verify the contents. Contents include an Allen
wrench, a key, and the parts and fasteners shown in “Parts.”
2. Dispose of/recycle all packaging materials.
Assemble Cabinet
Gather the required tools before starting installation.
Tools Needed:
Tools Supplied:
IMPORTANT:
■Two people may be required to complete the assembly.
■As you assemble the cabinet, make sure the edges with the
holes are facing up.
■If you are assembling the cabinet on the floor, fasten the eight
front corner bolts, two at each corner, after you stand the cabinet
upright.
1. Place side panel (P1) on a flat, firm surface so that the edge with
the holes is facing up as shown.
2. Insert the cabinet top (P2) between the edges of side panel (P1).
NOTE: Make sure the edges with the holes are facing up.
3. Align the holes and attach the top (P2) to side panel (P1) using
six Allen-head bolts (F1) and ⁵⁄₁₆"
flange nuts (F2) as shown. Do
not tighten completely.
4. Position the other side panel (P1) so that the top (P2) is between
the edges of side panel (P1).
5. Align the holes and attach the top (P2) to the side (P1) using six
Allen-head bolts (F1) and ⁵⁄₁₆"
flange nuts (F2) as shown. Do not
tighten completely.
6. Insert the cabinet bottom (P3) between the edges of the side
panels (P1).
NOTE: Make sure the edges with the holes are facing up.
7. Align the holes and attach the bottom (P3) to the sides (P1) using
six Allen-head bolts (F1) and ⁵⁄₁₆"
flange nuts (F2) for each side as
shown. Do not tighten completely.
Attach Back Panels
IMPORTANT:
■Attach the back panels (P8) starting at the top of the cabinet and
working down to the cabinet bottom. Each consecutive back
panel will overlap the panel above.
■Do not completely tighten the screws until all back panels are in
place.
1. Align the first back panel (P8) with the holes in the cabinet top.
Using Phillips-head screws (F3b), attach the panel (P8) to the
cabinet top and sides.
2. Overlap the bottom of the first back panel (P8) with the top of the
second back panel (P8) as shown. Using Phillips-head screws,
fasten back panel (P8) to the cabinet sides.
3. Repeat Step 2 to attach the four remaining back panels to the
cabinet sides.
F1 F2
F1 ⁵⁄₁₆ " Allen-head bolt (24)
F2
⁵⁄₁₆ " Flange nut (24)
■¹⁄₂" Wrench
■³⁄₈" Wrench
■¹¹⁄₃₂" Wrench
■Phillips screwdriver
■Pliers
■Level
■Allen wrench ■Key
WARNING
Excessive Weight Hazard
Use two or more people to move, assemble or install
cabinet or locker.
Failure to do so can result in back or other injury.
F3b
F3b Phillips-head screw (40)
A. Cabinet top
P1
P1
P2
P3
P1
P2
A

4
4. Using two Phillips-head screws, attach each back panel to the
panel above.
NOTE: Using three Phillips-head screws, attach the last back
panel (P8) to the cabinet bottom (P3).
5. Completely tighten all back panel screws starting with the sides
and continuing with the top, middle and bottom.
6. Using the Allen wrench (provided), completely tighten all 24
cabinet bolts and nuts.
Install Leveling Legs
1. Place the cabinet on its side.
2. Screw a leveling leg (P4) into each of the four rivet nuts located at
the corners of the cabinet as shown.
3. Stand the cabinet upright.
4. If you have not already, fasten the two bolts at each front corner,
of the cabinet frame. Completely tighten all the cabinet bolts and
nuts.
Install Shelves
IMPORTANT: Use the pair of holes located in the middle of the
cabinet sides to install a center shelf (P5), so the doors will close and
lock. The other two shelves may be installed where desired.
1. Place a shelf (P5) so that the holes in the ends are aligned with
the pair of holes in the middle of the cabinet sides.
NOTE: Make sure the hole in the center of the long shelf edge is
facing out.
2. Using two bolts and nuts per side, fasten the shelf (P5) to the
sides (P1).
3. Insert the door catch pin (F5) into the hole in the front edge of the
shelf. Use ¹¹⁄₃₂" wrench to fasten it with the star nut (F6).
4. Determine where you want to place the other two shelves (P5).
Align the holes in the shelf ends with the holes in the cabinet
side.
NOTE: Make sure the hole in the center of the long shelf edge is
facing the cabinet front.
5. Using two bolts and nuts per side, fasten the shelves (P5) to the
cabinet sides (P1). Completely tighten the nuts.
A. Cabinet bottom
A. Leveling legs
P1
P3
P1
P2
P8
P8
P8
P8
P8
P8
A
P3
P1
P4
P8
A
F3b F4 F5 F6
F3b
F4
Phillips-head screw (12)
Small flange nut (12)
F5 Door catch pin (1)
F6 Star nut (1)
A. Door catch pin and star nut
B. Middle pair of holes in cabinet side
B
A
P1
P2
P1
P3
P5

5
Install Doors
IMPORTANT: The door with the lock assembly (P7) should be
installed on the right-hand side of the cabinet.
1. Align the holes in the right-hand door hinge with the holes in the
right-hand cabinet side.
2. Using six Phillips-head screws, starting with the top hole, fasten
the door (P7) to the cabinet side. Hand-tighten the screws.
3. Insert the door catch (F9) into the rectangular opening, above the
lock, as shown.
4. Repeat steps 1 and 2 to attach the left-hand door (P6).
5. Align the doors and fully tighten the screws.
Complete Assembly
1. Make sure there is a bolt or screw in each hole of the cabinet
frame.
2. Move the cabinet to its final location.
3. Place a level on an inside shelf, and if necessary, level the
cabinet by adjusting the height of the leveling legs. Turn to the
left to raise or to the right to lower the leveling leg.
4. If the doors are not aligned, loosen all the screws attaching the
door hinge to the cabinet.
5. Adjust door to the desired height, and fully tighten the screws.
ACCESSORIES
To order accessories, call 1-866-342-4089 and ask for the accessory
part number listed below or contact your authorized Gladiator®
GarageWorks dealer. In Canada, call 1-800-807-6777.
Mounting Bracket Kit - Allows the cabinet to be mounted on
Gladiator® Garageworks GearWall®panels or GearTrack®channels.
Order Part # GABK362PSS
F3b F9
F3b
F9
Phillips-head screw (12)
Door catch (1)
A. Phillips-head screws
P1
P2
P3
P7
P5
P5
P5
A
F9