Whirlpool MK6120XAQ User manual

STEP 1 STEP 2
PART UST CUT-OUT DIMENSIONS
/NSTALfdTION /h/STRUCT/Of’tf FOR WHIRLPOOL TRIM-KIT MODELS: MK6120XAQ. MK6120XAB. MK6120XAZ. MK612OXAY
FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MT5120XAQ MT6120X(Q, MT6120XY0. MT6900XW. MT6901XW, KCMSlPPYWH, KCMSIPSYAL. KCMS125YWH, KCMS125YAL. KCMSl25YSB
[ UL L&TED - FOR USE OVER GAS 8 ELECTRIC HEAT SOURCE INCLUDING MODELS: RB260PXY, RB220PXY, KEBltO9Y, KEBS107Y 1
v
Low Profile Screws
6 Req’d
Duct D4
Spring Clips
4 Req’d
STEP 3
1. Disconnect microwave and remove any loose
4 items inside the oven before proceeding with
installation.
2. Detach Exiting Strews(4) from the microwave
cabinet sides at locations as indicated.
3. Install Ducts D4 and DlO by re-attaching Exisling
Strews(4) and using No.10 Screws(Z) as shown.
4. Position Duct D6 over microwave, covering
rear exhaust vent. Loose/y attach Duct
using No.12 Screws(P) as shown.
5. Lift the front of Duct D6 and peel backing off
double sided tape tram the Duct bottom. Press
down firmly on Duct. Tighten No.12 Strews(2)
at the back.
PART NO. 4313745
REAR WEW OF MICROWAVE
- Duct D6
Height = 15 ‘/,’
Length = 26 ‘/*.
Depth = 23 “/,’ (min.)
Microwave Oven
Cutout Opening
LBuilt-In Oven
cutout openhlg
STEP 4
1. Mark center positions (or center-punch)
for the Anti-Tip Bracket as shown.
Dlmenslons:
A = 4 ‘12’
B = 3 ‘Ia’
c = 17 ‘I,’
2. Drill pilot holes as required.
3. Install Anti-Tip Bracket
with Low Profile
Strews(2) as shown.
<---
_---
‘\ ‘\ ‘\ ‘\ ‘\
Cutout Floor
Low Profile Screws 7
Anti-Tip Bracket
Page 1

i
5STEP
I. Place microwave oven in the opening
of the cut-out. Be careful nof lo
bend the Ad-Tip Flange. Flange
must be flat to cut-out floor to
engage correctly with Anti-Tip
Bracket as shown.
2. Plug in microwave oven.
3. Center microwave oven within
the cut-out opening and slide
oven in place.
4. After oven is in place, ensure
microwave is accurafely cenlered.
5. Drill pilot holes through
Positioning Flanges and install
Low Profile Screws(P) at the
front of the Ducts as shown.
Anti-TIP Assembly
Lo
Flanges
7STEP
1. Place Trim Frame over the microwave.
Make sure microwave is centered within
the Frame. Firmly push Frame against
the wall at the four Spring Clip
locations as shown.
2. Check Frame for fig’ghffit. If Frame
is loose, remove the Frame and make
necessary adjustments by loosening the
Screws, re-positioning the Clips and
re-tightening the Screws. Re-attach
Frame as above.
PART NO. 4313745
6STEP
1. Mark center positions (or center punch) for
the pilot holes(4) as shown. DimA is
measured from the cut-oul bottom and
Dim.B is from the cut-out side. The Q Top Clip Position
top hole is determined by Dim.C.
Dlm.A = ‘/,;
Dlm.B = ‘/; (mln.)
Dlm.C = 16 ‘/, Dim. C
2. Drill pilot holes and install the Spring 1
Clips(4) using Low Profile Strews(4). _.-. _-L
Note that the top Clips face up and
the bottom Clips face down as shown. Dim. A -+ *Dim. B
cutout
3. The Spring Clips are provided with a Opening
slotted hole for fine adjustments as required.
6STEP
1. Your Trim-Kit is now fully
installed. Replace any loose
items that might have been
removed from the oven.
2. Please keep this installation
instruction for future reference.
Page 2