Whirlpool MK6124XAQ User manual

INSTALLdTlON INSTRUCTION FOR WHIRLPOOL TRIM-KIT MODELS: MK6124XAQ MK6124XAB (KEEP FOR FUTURE REFERENCE)
FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS: MT5120XAQ. MT6120X-YQ MT6120XYB. MT6900XW, MT6901X-W. KCMS122YWH, KCMS125YWH
[ UL USTED - FOR USE OVER GAS & ELECTRIC HEAT SOURCE INCLUDING MODELS: SB130PER. SBiGOPD(. RBlGOPXY. KEBl141Y, RBlZOPXY, RBlOOPXY. RBlOO5a )
STEP 1
PART LIST
2STEP
CUT-OUT DIMENSIONS Microwave Oven
Cutout Openin
Aluminum Vent
Low Profile ScreWS
3STEP
1. Disconnect microwave and remove any loose
items inside the oven before proceeding with
d installation.
2. Detach Exiting Strews(4) from the microwave
cabinet sides at locations as indicated.
3. Install Ducts D4 and DlO by m-attaching Existing
Strew.(4) and using No.10 Strews(2) as shown.
4. Position Duct D6 over microwave, covering
rear exhaust vent. Loosely attach Duct
using No.12 Strews(2) as shown.
5. Lii the front of Duct D6 and peel backing off
double sided tape from the Duct bottom. Press
down firmly on Duct. Tighten No.12 Screws(S)
at the back.
PART NO. 4313741
REAR VIEW OF MICROWAVE
,./za Duct D6
Height = 15 ‘/,’
Length = 22 ‘&’
Depth = 23 “I,’ (min.) \Built-in ‘Oven
Cutout openklg
STEP 4
1. Mark center positions (or center-punch)
for the Anti-Tip Bracket as shown.
Dimenslons:
A = 1 =/,’
0 = 3 ‘I,’
c = 17 ‘I.’
2. Drill pilot holes as required.
3. Install Anti-Tip Bracket
with Low Profile
Low Profile Screws 7 $$J
Anti-Tip Bracket *
Screw(P) as shown.
Page 1

STEP 5
I.
2.
3.
4.
5.
Place microwave oven in the opening
of the cut-out. Be careful nof to
bend the Anti-Tip Flange. Flange
musl be flat lo cut-out floor to
engage correctly with Anti-Tip
Bracket as shown.
Plug in microwave oven.
Cenler microwave oven within
the cut-out opening and slide
oven in place.
After oven is in place, ensure
microwave is accurately centered.
Drill pilot holes through
Positioning Flanges and install
Low Profile Strews(2) at the
front of the Ducts as shown.
Antl-Tip Assembly
STEP 6
Low Profile
Screws
L Flange
cutout
Opening
Posilionina
Flanges -
7STEP
1.
Place Trim Frame over the microwave.
Make sure microwave is centered within
the Frame. Firmly push Frame against
the wall at the four Spring Clip
locations as shown.
2. Check Frame for tight fil. If Frame
is loose, remove the Frame and make
necessary adjustments by loosening the
Screws, re-posthoning the Clips and
m-tightening the Screws. &-attach
Frame as above.
PART NO. 4313741
1. Mark center positions (or center punch) for
the pilot holes(4) as shown. Dim.A is
measured from the cut-out bottom and
Dim.B is from the cut-out side. The
top hole is determined by Dim.C.
Dlm.A = ‘I,,,-
Dlm.B = ‘/,’ (mln.)
Dlm.C = 16 %’
Top Clip PoSitIon
a~jfY:.FjnDim. c
-s
2. Drill pilot holes and install the Spring
Clips(4) using Low Profile Strews(4).
Note that the top Clips face up and
the bottom Clips face down as shown.
3. The Spring Clips are provided with a
Position Opening
slotted hole for fine adjustments as required.
6STEP
1. Your Trim-Kit is now fully
Installed. Replace any loose
items that might have been
removed from the oven.
2. Please keep this installation
instruction for Mure reference.
Page 2