Whirlpool MWHSL60g Operating and installation instructions

SERVICE Whirlpool EMEA
Customer Services MWHSL60g
V-ZUG Service Information
MWHSL60g
8591 232 16920
Last Modification: 17/04/15
Creation Date: 14/11/14
Spare Part List 2
Exploded View 3
Technical Data 4
Safety Instructions 5
Dimensional Sketch 7
Wiring Diagram 8
This document is only intended for qualified technicans who are aware of the
respective safety regulations.
Subject to modifications
© Whirlpool EMEA www.scc-service.com
1022055-00 rev AA

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 2 of 8
Spare Part List
Pos 12NC Description
0221 4801 201 00678 Profile left
0222 4801 201 00679 Profile right
0410 4810 104 89758 Hinge VZUG 2-GLASS MIDI
1170 4819 498 78366 Handle crisp plate
1300 4810 104 58544 Holder Switch MIDI
1305 4801 201 00677 Spring,tension
1308 4810 104 58550 Disc cam MIDI
1410 4810 107 12342 Door cpl. MIDI 60 VZ ANIA2
2441 4840 000 00699 Lid plastic 27cm diam.
2450 4820 000 04533 Grill grid high124mm diam.272mm
2460 4801 201 00687 Crisp plate
2550 4819 418 79728 Turntable glass
2640 4810 104 22374 Turntable ring
2641 4810 105 45578 Crosspiece TT DRIVE HT
3010 4810 107 56604 Control panel 50-600 VZ GLUED MIDI
3310 4810 107 56421 Knob ANIA2
3560 4810 107 62942 Display board MIWELL - SL
4040 4810 104 91930 Magnetron LG 2M226-20GWH
4060 4810 678 48981 Motor TT
4120 4810 104 88906 Transformer R*H.V 230V/50Hz PHOENIX
4200 4812 121 58161 Capacitor HT
4210 4812 122 08003 Filter, mains
4260 4812 218 38323 Diode HV
4410 4801 201 00527 Motor fan
4520 4801 201 00667 Heating element
4800 4810 107 39821 Cable harness FLAT R2.5 5-POL L600
4801 4810 107 09539 Cable harness UI HMI NAV ANIA2
4900 4801 201 00666 Cable mains CH
5000 4810 106 98127 Control board UI MUNIN 50mm MIDI ANIA2
5210 4810 107 10791 Control board LOKE MIDI VZ GR NAV 50Hz
5570 4801 201 00003 Thermostat 165°C
5571 4810 678 47931 Thermostat 36FXE24 20202 L130C TOD
5620 4819 252 28125 Fuse T10A
6330 4801 201 00814 Microswitch
6520 4812 134 18008 Lamp
6560 4801 201 01622 Lampholder MIBI MIDI
7740 4801 201 00672 Plate mica
9220 4819 532 68686 Gasket ring for TT
9931 4801 201 00681 Mounting kit not shown
© Whirlpool EMEA www.scc-service.com

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 3 of 8
Exploded View
© Whirlpool EMEA www.scc-service.com

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 4 of 8
Technical Data
Electrical base data
Voltage ...................................................................................................230 V
Frequency ............................................................................................... 50 Hz
Currentconsumption ......................................................................................10A
Power Consumption
Totalconnectedload ...................................................................................2300 W
Microwave
Outputpower .......................................................................................1000W
Grill ..................................................................................................... 800W
Auto timer ............................................................................................Navigator
Accessories
Turntable diameter .....................................................................................325 mm
Cover plate
Diameter ...........................................................................................272 mm
grid
Diameter ...........................................................................................291 mm
Crisp
Diameter ...........................................................................................310 mm
© Whirlpool EMEA www.scc-service.com

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 5 of 8
Safety Instructions
INTRODUCTION
Before leaving the factory each oven is carefully checked.
It must, however, be installed and used correctly.
Despite all the steps taken to make the oven safe, the safety is dependent on the correct installation and the fact the
user understands how to use and maintain the oven.
The information in this section should be used as a reminder that the oven is safe and that anyone who uses it must
first read the instructions for use in order to be able to use the oven correctly and obtain best results.
SAFETY
To avoid injury to yourself and damage to the appliance always work to the following rules when servicing an oven.
Always disconnect the plug from the mains before starting work.
If there is no plug switch off the electric supply at the control box.
When you have finished servicing an oven before you reconnect it to the mains, make sure that:
– all the internal connections are correct
– the wires are insulated and not touching the door or the cabinet or anything sharp
– all the earth connections are electrically and mechanically sound
– do not modify or anyway interfere with the safety devices built-in to the oven
– make sure that each replacement part you use conforms to the manufacturer´s specifications
Do not start a repair if you have any doubt as to your ability to complete it.
CAUTION - MICROWAVE RADIATION
© Whirlpool EMEA www.scc-service.com

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 6 of 8
PERSONNEL SHOULD NOT BE EXPOSED TO THE MICROWAVE ENERGY WHICH MAY RADIATE FROM THE
MAGNETRON, WAVEGUIDE OR ANTENNA IF THEY ARE IMPROPERLY USED OR CONNECTED. ALL INPUT
AND OUTPUT MICROWAVE CONNECTIONS, WAVEGUIDES, FLANGES AND GASKETS MUST BE SECURE.
NEVER OPERATE THE DEVICE WITHOUT A MICROWAVE ENERGY ABSORBING LOAD ATTACHED.
NEVER LOOK INTO AN OPEN WAVEGUIDE OR ANTENNA WHILE THE DEVICE IS ENERGIZED.
NEVER OPERATE AN OVEN WITH CABINET OFF WITHOUT MEASURING THE MICROWAVE LEAKAGE
AROUND MAGNETRON AND VISIBLE MICROWAVE CONNECTIONS (WELDING JOINTS).
Do not operate the oven if the following conditions exist:
– the door does not close firmly against the door support because of the door being warped or the hinges damaged.
– The door trims or seals are damaged.
– If there is any visible damage to the oven.
– if the door does not close properly.
Avoid operating the oven if known components in the interlock system, oven door or microwave
generating assembly are known defective. They must be replaced.
WARNING - HIGH VOLTAGE
IT IS POSSIBLE TO COME IN CONTACT WITH LETHAL HIGH VOLTAGE WHEN WORKING WITH HV TRANS-
FORMER, HV CAPACITOR AND MAGNETRON. THEREFORE NEVER TRY TO MEASURE THE HIGH VOLTAGE.
ALWAYS TAKE UTMOST CARE WHEN PERFORMING ELECTRIC MEASUREMENTS INSIDE THE OVEN.
© Whirlpool EMEA www.scc-service.com

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 7 of 8
Dimensional Sketch
© Whirlpool EMEA www.scc-service.com

SERVICE Whirlpool EMEA
Customer Services
8591 232 16920, 17/04/15
page 8 of 8
Wiring Diagram
© Whirlpool EMEA www.scc-service.com