Whirlpool AVM562 User manual

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 1 OF 17
WHIRLPOOL ELECTRICAL APPLIANCES
COMPANY LIMITED
SERVICE INFO MANUAL
MODEL: AVM562
SKU No.: 853856258291
DATE: October 7, 2005
REVISION: a

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 2 OF 17
CONTENTS
1. SPECIFICATIONS
2. SAFETY PRECAUTIONS
3. INSTALLATION REQUIREMENTS
3.1 GENERAL
3.2 GROUNDING INSTRUCTIONS
4. SCHEMATIC DIAGRAM
5. MICROWAVE AND MICROWAVE LEAKAGE TEST
5.1 MICROWAVE TEST
5.2 MICROWAVE LEAKAGE TEST
6. TROUBLE SHOOTING GUIDE
6.1 CAUTION AND IMPORTANCE
6.2 MICROWAVE LEAKAGE
6.3 QUICK REFERENCE
7. MAJOR COMPONENT TESTS
7.1 HV TRANSFORMER
7.2 HV CAPACITOR
7.3 HV DIODE
7.4 MAGNETRON
7.5 INTERLOCK SWITCH SYSTEM
8. PART LIST & EXPLODED DIAGRAM

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 3 OF 17
1. SPECIFICATION
Model
AVM562
Outer dimension(H x W x D)
285x456x402mm
Volume of cavity
17.8Liter
Basic function
Microwave only cooking
Grill only cooking
Control
Electronic touch foil control
99-minute cook time
10-level microwave power level
Programmable
Power supply
220V 60Hz, single phase
Output power
Microwave: 800W
Grill: 1000W
Power consumption
Max 1250W
Current consumption
8 A
Microwave frequency
2450 MHz

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 4 OF 17
2. SAFETY PRECAUTIONS
This manual is intended for use by personnel with adequate background in
electrical, electronic and mechanical engineering. Any improper attempt to repair
this oven may result in personal injury and property damage. The manufacturer or
seller cannot be hold responsible for the interpretation of this manual nor can they
assume any liability in connection with its use.
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING
SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE
MICROWAVE ENERGY.
1. Do not operate or allow the oven to be operated when the door is opened.
2. Perform the following safety checks on the oven to be serviced before
activating the magnetron or other microwave sources and make repairs when
necessary:
Interlock operation
Proper closing of door
Door bending
Seal and sealing surfaces (arcing, wear or other damages)
Damage to or loosening of hinges or latches
Evidence of dropping or abuse
Door window is intact
3. Before turning on the microwave power for any service test or inspection
within the microwave generating compartments, check the magnetron,
waveguide or transmission line, and cavity for proper alignment, integrity, and
connections.
4. Any defective or misadjusted components in the interlock, monitor switch,
door seal, and microwave generation and transmission system shall be
repaired, replaced, or adjusted by procedures described in this manual before
the oven is released to the owner.
5. A microwave leakage check to verify compliance with the appropriate
standard should be performed on each oven prior to release to the owner.
TO PREVENT ELECTRICAL SHOCK, PAY EXTREME CAUTION
WHEN DIAGNOSING OVEN WITH OUTER CASE REMOVED AND
POWER TURNED “ON”. THE HIGH VOLTAGE SECTION OF THE
POWER SUPPLY, INCLUDING FILAMENT LEADS, ARE AT A HIGH
TENSION OF -4000 VOLTS. ALSO, ENSURE THAT THE HIGH
VOLTAGE CAPACITOR IS DISCHARGED.

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 5 OF 17
3. INSTALLATION REQUIREMENTS
3.1 GENERAL
1. The oven should be placed on a flat and stable surface
2. Place the oven away from high temperature and steam sources.
3. Clearance of at least 5cm (2”) on each side must be provided to allow
adequate ventilation.
4. The microwave oven must be plugged directly to a 3-prong wall receptacle
which is properly grounded.
5. The power source must be 230V 50Hz 8A single phase.
3.2 GROUNDING INSTRUCTIONS
IMPORTANCE:
DISCONNECT POWER BEFORE SERVICING, RECONNECT ALL
GROUNDING DEVICES.
All mechanical parts of this appliance capable of conducting electricity are
grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock. This appliance is equipped with a cord having a grounding wire
with a ground plug. The plug must be plugged into an outlet that is properly
installed and grounded.
WARNING:
IMPROPER USE OF THE GROUNDING PLUG MAY RESULT IN
ELECTRICAL SHOCK.
If grounding wires, screws, straps, clips, nuts or washers used to complete a path
to ground are removed for service, they must be returned to their original
positions and properly fastened.
GROUNDING SPECIFICATION:
Leakage current: 0.75mA max.
Ground path resistance: 0.1ohm max.

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 6 OF 17
4. SCHEMATIC DIAGRAM

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 7 OF 17
5. MICROWAVE AND MICROWAVE LEAKAGE TESTS
5.1 MICROWAVE TEST
The following is a simple test to check if the appliance is generating microwave
energy. This test is not intended to be an accurate test. An accurate measurement
of output power must be performed under strict control following the IEC
standard. In field service, accurate measurement of output power is usually not
required.
1. Prepare a beaker of water of quantity about 1000cc.
2. Measure the temperature of the water before putting into the oven.
3. Heat the water in the oven with full power (microwave only) for 60 seconds.
4. Again measure the temperature of the water.
5. If the temperature rise by about 10 degree Centigrade, then the microwave
generating system is working.
5.2 MICROWAVE LEAKAGE TEST
5.2.1 TESTING EQUIPMENT
600cc beaker
Microwave meter
5.2.2 TESTING PROCEDURE
1. Place 275cc of water into the beaker and place it in the center of the oven.
2. Turn on the microwave oven by turning the setting the cook time and start at full
power.
3. Hold the probe of the microwave meter perpendicular to the surface of the oven
and scan it at the rate of 1 inch/sec.
4. Test the following areas for microwave leakage:
Door and control panel
All ventilation openings
All lockseams
Weld at bottom
Bottom plate
Oven foot

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 8 OF 17
5. Pull the door to the position at which the oven is just about to turn off due to the
interlock switch action, scan the door perimeter for microwave leakage.
6. Maximum allowable leakage is 4 mW/cm2.
7. Record all data.
5.2.3 OVEN MICROWAVE LEAKAGE REPAIR
If leakage figure is found to be above 5 mW/cm2, owner should be told not to use
the oven until it has been serviced. Service personnel should notify the
manufacturer immediately.
5.2.4 OPEN DOOR TEST
With the oven in operation state, open the oven door and check if the oven is still
operating. If so, the service personnel should tell the owner not to operate the
oven again and should notify the manufacturer and immediately.
6. TROUBLE SHOOTING GUIDE
6.1 CAUTION AND IMPORTANT
1. Before disassembling the oven, the oven power must be turned off. Remove the
power plug of the oven from the outlet and wait for at least 3 minutes.
2. When disassembling, service personnel should remove their watches and metal chains
from their hands. Never touch the high voltage components and wire.
3. Before checking or replacing, discharge the high voltage capacitor to oven chassis
grounded with an insulated wire. Make sure that the wire is grounded to chassis side
before short circuiting the capacitor terminal.
4. Do not measure high voltage with a common voltmeter.
6.2 MICROWAVE LEAKAGE
1. Refer to section 5.2 regarding microwave leakage. If the leakage is greater than 4
mW/cm2, it is necessary to repair the oven.
2. If leakage is found worst at control panel, ventilation openings or oven bottom, check
if there is any damaged parts or loose screws in the respective areas. If so, replace the
damaged parts and fasten the screws.

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 9 OF 17
3. If leakage is found worst around the door perimeter, adjust the interlock support or
change the door.
6.3 QUICK SERVICE REFERENCES
PROBLEM
POINTS TO CHECK
Cavity lamp does not light, but other
electrical components (e.g. turntable)
are working.
1. Lamp burnt.
2. Bad contact between lamp and lamp
socket.
Cavity lamp does not light, all other
electrical components also do not work.
1. Power plug not in good connection with the
socket. No power supply.
2. Fuse blown.
3. Bad contact between fuse and fuse
holder/clip.
4. Loose door hinge, door poorly adjusted,
interlock poorly adjusted; causing fuse to
be blown.
5. Short circuit within electrical circuit.
Lamp filament short, HV transformer short,
all causing fuse blown.
6. Bad contact in contacts or terminals of
power relay, primary and secondary
interlock switch.
7. HV diode break down.
Oven seems working, food is not
cooked.
1. Defective magnetron(filament broken,
filament short to ground etc.).
2. Ground wire of HV transformer broken.
3. Filament wire short to ground.
4. Filament wire broken.
5. Bad contact in magnetron terminals.
6. Defective control boards.
7. HV diode break down, giving a hum noise.
Oven cooks for a short while and stop.
1. Cooling fan jammed.
2. Cooling fan motor open circuit..
Turntable does not turn.
1. Defective turntable motor.
2. Turntable shaft deformed.
User circuit breaker activates.
1. High leakage in electrical components
(mostly motor).

WHIRLPOOL ELECTRICAL APPLIANCES CO. LTD. SERVICE MANUAL
Ref : 56258291a PAGE 10 OF 17
7. MAJOR COMPONENT TESTS
7.1 HV TRANSFORMER
1. Remove lead wire.
2. Measure the resistance of the winding using an ohm meter
3. Primary winding 3 ohm (approx.)
4. Secondary winding 100 ohm (approx.)
5. Filament winding 0 ohm (approx.)
7.2 HV CAPACITOR
1. Remove lead wire
2. Measure the resistance using an ohm meter set to R*1000
3. Terminal to terminal should momentary indicates several ohms but gradually
increases to infinite.
4. Terminal to case should show infinite.
7.3 HV DIODE
1. Remove lead wire.
2. Measure forward resistance, normal diode show continuity.
3. Measure reverse resistance, normal diode show infinite resistance.
7.4 MAGNETRON
1. Remove lead wire.
2. Install the magnetron gasket in the correct position. Check that the gasket is in
good condition.
3. Measure the resistance of the filament terminals. Normal magnetron should
be less than 1 ohm.
4. Measure the resistance between the filament terminal to chassis. Normal
magnetron should be infinite.
7.5 INTERLOCK SWITCH SYSTEM
IMPORTANT: The installation of the interlock and monitor switches is
required by Federal regulations.
Oven door
status
Primary switch
Secondary
switch
Monitor
switch
Open
Open
Open
Close
Close
Close
Close
Open