Whirlpool W10462760B User manual

TOP MOUNT
REFRIGERATOR
Use & Care Guide
Table of Contents.................2
RÉFRIGÉRATEUR
SUPERPOSÉ
Guide d'utilisation et d'entretien
Table des matières.................2


2.................
W10462760B

TABLE OF CONTENTS
REFRIGERATOR SAFETY .................................................... 3
Proper Disposal of Your Old Refrigerator ................................. 3
INSTALLATION INSTRUCTIONS .......................................... 4
Unpack the Refrigerator ........................................................... 4
Location Requirements............................................................. 4
Electrical Requirements............................................................ 5
Water Supply Requirements..................................................... 5
Connect the Water Supply........................................................ 6
Refrigerator Doors .................................................................... 7
Adjust the Doors..................................................................... 11
Install Air Filter ........................................................................ 11
REFRIGERATOR USE ........................................................12
Using the Controls.................................................................. 12
Water Dispenser ..................................................................... 14
Water Filtration System........................................................... 15
Ice Maker ................................................................................ 16
REFRIGERATOR FEATURES..............................................16
Refrigerator Shelves ............................................................... 16
Meat Drawer ........................................................................... 17
Crisper .................................................................................... 17
FREEZER FEATURES ........................................................ 18
Wire Freezer Shelf................................................................... 18
Glass Freezer Shelf................................................................. 18
DOOR FEATURES.............................................................. 19
Door Rails ............................................................................... 19
Door Bins................................................................................ 19
Utility Compartment and Can Caddy ..................................... 19
REFRIGERATOR CARE...................................................... 19
Cleaning.................................................................................. 19
Changing the Light Bulbs ....................................................... 20
Vacation and Moving Care...................................................... 20
TROUBLESHOOTING......................................................... 21
Refrigerator Operation............................................................ 21
Temperature and Moisture...................................................... 22
Ice and Water.......................................................................... 22
ACCESSORIES .................................................................. 23
ASSISTANCE OR SERVICE ................................................ 23
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR....................................... 24
Mise au rebut de votre vieux réfrigérateur.............................. 24
INSTRUCTIONS D’INSTALLATION .....................................25
Déballage du réfrigérateur ...................................................... 25
Exigences d'emplacement ..................................................... 25
Spécifications électriques....................................................... 26
Spécifications de l'alimentation en eau.................................. 26
Raccordement à l'alimentation en eau ................................... 27
Portes du réfrigérateur............................................................ 29
Réglage des portes................................................................. 33
Installation du filtre à air.......................................................... 33
UTILISATION DU RÉFRIGÉRATEUR................................... 34
Utilisation des commandes .................................................... 34
Distributeur d'eau ................................................................... 36
Système de filtration de l'eau ................................................. 37
Machine à glaçons.................................................................. 38
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ......................39
Tablettes du réfrigérateur........................................................ 39
Tiroir à viande ......................................................................... 39
Bac à légumes ........................................................................ 40
CARACTÉRISTIQUES DU CONGÉLATEUR......................... 40
Tablette métallique du congélateur......................................... 40
Tablette en verre du congélateur ............................................ 41
CARACTÉRISTIQUES DE LA PORTE.................................. 41
Tringles dans la porte.............................................................. 41
Balconnets de porte ............................................................... 41
Compartiment utilitaire et compartiment à canettes .............. 42
ENTRETIEN DU RÉFRIGÉRATEUR..................................... 42
Nettoyage ............................................................................... 42
Remplacement des ampoules d’éclairage ............................. 43
Précautions à prendre pour les vacances et avant un
déménagement....................................................................... 43
DÉPANNAGE............................................................................. 44
Fonctionnement du réfrigérateur ............................................ 44
Température et humidité......................................................... 45
Glaçons et eau........................................................................ 45
ACCESSOIRES .................................................................. 47
ASSISTANCE OU SERVICE ................................................ 47

3........................................................................
3....................................................
4....................................................................
4.......................................................... 
4............................................................................ 
5......................................................................
5....................................................................
6..................................................................... 
7...............................................................................
11.............................................................................
11.....................................................................
12................................................................... 
12..................................................................
14............................................................................... 
15....................................................................... 
16.................................................................................
16......................................................................
16............................................................................ 
17................................................................................
17......................................................................
18...................................................................... 
18......................................................................... 
18...................................................................... 
19................................................................
19.............................................................................
19
19....................................................... 
19.....................................................................
19............................................................................
20............................................................................
20..............................................................
21................................................. 
21.............................................................................
22.............................................................. 
22................................................................................ 
23.............................................................................
23.................................................................. 
2

3
REFRIGERATOR SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
SAVE THESE INSTRUCTIONS
■Plug into a grounded (earthed) outlet.
■Do not remove ground prong.
■Do not use an adapter.
■Do not use an extension cord.
■Disconnect power before servicing.
■Replace all parts and panels before operating.
■Remove doors from your old refrigerator.
■Use nonflammable cleaner.
■Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
■Use two or more people to move and install refrigerator.
■Disconnect power before installing ice maker (on ice maker
kit ready models only).
■A qualified service technician must install the water line and
ice maker.
■Use a sturdy glass when dispensing ice (on some models).
■This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety.
■Children should be supervised to ensure that they do not
play with the appliance.
■If the power supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
Proper Disposal of
Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
– even if they will sit for “just a few days.” If you are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■Take off the doors.
■Leave the shelves in place so that children may not easily
climb inside.
WARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.

4
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
Remove the Packaging
IMPORTANT: Do not remove the white foam air return insert from
behind the control panel on the ceiling of the refrigerator. If the
insert is removed, ice may migrate down from the freezer and
cause icicles to form.
1. Using two or more people, tilt the refrigerator to one side.
Remove the screws fastening the plastic runner to the bottom
of the refrigerator. Repeat to remove the runner from the
opposite side.
2. Locate the brake foot inside the crisper drawer. Insert the
brake foot into the bottom hole of the roller assembly on the
front, hinge side of the refrigerator.
NOTE: The brake foot is used when leveling the refrigerator.
To level the refrigerator, see “Adjust the Doors.”
3. Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Rinse with warm water
and dry with a soft cloth.
NOTE: Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove tape or glue.
These products can damage the surface of your refrigerator.
For more information see “Refrigerator Safety.”
Clean Before Using
After you remove all of the package materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
“Refrigerator Care.”
Location Requirements
IMPORTANT: This refrigerator is designed for indoor household
use only.
To ensure proper ventilation for your refrigerator, allow for ½"
(1.25 cm) of space on each side and at the top. Allow for 1"
(2.54 cm) of space behind the refrigerator. If your refrigerator has
an ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed wall,
leave a 2" (5.08 cm) minimum space on the hinge side (some
models require more) to allow the door to swing open.
NOTE: This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a maximum
of 110°F (43°C). The preferred room temperature range for
optimum performance, which reduces electricity usage and
provides superior cooling, is between 60°F (15°C) and 90°F
(32°C). It is recommended that you do not install the refrigerator
near a heat source, such as an oven or radiator.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
When MovingYour Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for
cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
“walk” the refrigerator when trying to move it, as floor
damage could occur.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
1 / 2" (1.25 cm)
2" (5.08 cm)

5
Electrical Requirements
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection:
Recommended Grounding Method
A 115 Volt 60 Hz. (Plug 1), 220/240 Volt 50 Hz. (Plugs 2 or 3), or
220 Volt 60 Hz. (Plug 3) AC only 10-amp fused and grounded
(earthed) electrical supply is required.
It is recommended that a separate circuit serving only your
refrigerator be provided. Use an outlet that cannot be turned off
by a switch or pull chain. Do not use an extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control, (Thermostat, Refrigerator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source and
reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
For Saudi Arabia:
Your new appliance has been especially manufactured to meet all
Saudi Arabia Standards and Conditions.
Some notations in the installation instructions may refer to
electrical requirements in other countries, so we draw your
particular attention to these specific notes.
Your appliance needs to be plugged into a 220 Volt 60 Hz 10-amp
(Plug 3) AC only earthed outlet.
Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
TOOLS NEEDED:
NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
IMPORTANT:
■All installations must meet local plumbing code requirements.
■Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
Water Pressure
A potable cold water supply with water pressure of between 30
and 120 psi (207 and 827 kPa) is required to operate the water
dispenser and ice maker. If you have questions about your water
pressure, call a licensed, qualified plumber.
■If your refrigerator has a water dispenser: After installation is
complete, use the water dispenser to check the water
pressure.
■With the water filter removed, dispense 1 cup (237 mL) of
water. If 1 cup of water is dispensed in 8 seconds or less,
the water pressure to the refrigerator meets the minimum
requirement.
■If it takes longer than 8 seconds to dispense 1 cup of
water, the water pressure to the refrigerator is lower than
recommended. See “Troubleshooting” for suggestions.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
■Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
■If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See “Water Filtration
System” in the User Instructions, User Guide, or Use & Care
Guide.
If you have questions about your water pressure, call a licensed,
qualified plumber.
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Plug 1 Plug 2 Plug 3
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
■Flat-blade screwdriver
■⁷⁄₁₆" and ¹⁄₂" Open-end or two
adjustable wrenches
■¹⁄₄" Nut driver
■¹⁄₄" Drill bit
■Cordless drill

6
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■Make sure it is a cold water pipe.
■Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
ends of copper tubing are cut square.
5. Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe you
have selected.
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut onto the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water is clear.
Turn OFF the shutoff valve on the water pipe. Coil the copper
tubing.
Connect to Refrigerator
Style 1
1. Unplug refrigerator or disconnect power.
2. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do not
overtighten.
3. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid
damage to the tubing when the refrigerator is pushed back
against the wall.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
6. The ice maker is equipped with a built-in water strainer. If your
water conditions require a second water strainer, install it in
the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain
a water strainer from your nearest appliance dealer.
Style 2
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. If the gray water tube supplied with the refrigerator is not long
enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in
order to connect the water tubing to an existing household
water line. Thread the provided nut onto the coupling on the
end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Sh uto ff val ve
G. Packing nut
A
B
C
DEF
G
A. Tube clamp
B. Tube clamp screw
C. Copper tubing
D. Compression nut
E. Valve inlet
A. Refrigerator water tubing
B. Nut (provided)
C. Bulb
D. Coupling (provided)
E. Ferrule (purchased)
F. Nut (purchased)
G.Household water line
A
C
B
D
E
A B C D E F G

7
Style 3
1. Unplug refrigerator or disconnect power.
2. Remove and discard the black nylon plug from the gray water
tube on the rear of the refrigerator.
3. Thread the provided nut onto the water valve as shown.
NOTE: Tighten the nut by hand. Then tighten it with a wrench
two more turns. Do not overtighten.
4. Turn shutoff valve ON.
5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Complete the Installation
1. Plug into a grounded 3 prong outlet.
2. Flush the water system. See “Water Dispenser.”
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill ice container.
Refrigerator Doors
TOOLS NEEDED: ⁵⁄₁₆" hex head socket wrench, #2 Phillips
screwdriver, flat-blade screwdriver, ⁵⁄₁₆" open-end wrench, flat 2"
putty knife.
IMPORTANT:
■Before you begin, turn the refrigerator control OFF, unplug
refrigerator or disconnect power. Remove food and any
adjustable door or utility bins from doors.
■Depending on your model, you have either Style 1 - interior
controls and water dispenser or Style 2 - exterior controls and
water dispenser. Follow the instructions and graphics specific
to your model.
■All graphics referenced in the following instructions are
included later in this section after “Final Steps.”
Style 1 - Remove Doors and Hinges
⁵⁄₁₆ " Hex Head Hinge Screw
1. Unplug refrigerator or disconnect power.
2. Open the refrigerator door and remove the base grille from the
bottom front of the refrigerator. See Base Grille graphic.
3. Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
4. Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.
5. Remove the parts for the center hinge as shown in the Center
Hinge graphic. Lift the refrigerator door free from the cabinet.
6. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.
NOTE: On some models, remove both the bottom hinge
assembly and the leveling foot.
Style 1 - Replace Doors and Hinges
NOTE: Provide additional support for the doors while the hinges
are being moved. Do not depend on the door magnets to hold the
doors in place while you are working.
1. Replace the parts for the bottom hinge as shown. Tighten
screws. Replace the refrigerator door.
NOTE: On some models, install both the bottom hinge
assembly and the leveling foot.
2. Assemble the parts for the center hinge as shown and tighten
all screws. See Center Hinge graphic. Replace the freezer
door.
3. Assemble the parts for the top hinge as shown in the Top
Hinge graphic. Do not tighten the screws completely.
4. Line up the doors so that the bottom of the freezer door aligns
evenly with the top of the refrigerator door. Tighten all screws.
A. Bulb
B. Nut (provided)
A
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING

8
Style 2 - Remove the Doors and Hinges
⁵⁄₁₆ " Hex Head Hinge Screw
1. Unplug refrigerator or disconnect power.
2. Open refrigerator door and remove base grille from the bottom
front of the refrigerator. See Base Grille graphic.
3. Disconnect the water dispenser tubing located behind the
base grille. The dispenser tubing runs through the door and
must be disconnected in order to remove the door. See Water
Dispenser Tubing Connection graphic.
■Press blue outer ring against the face of fitting and pull the
dispenser tubing free.
NOTE: Keep the water tubing connector attached to the
section of the tubing that runs underneath the refrigerator
cabinet.
4. Disconnect the wiring plugs located in the opening in the
bottom of the door. See Wiring Connection graphic.
5. Close the refrigerator door and keep both doors closed until
you are ready to lift them free from the cabinet.
NOTE: Provide additional support for the doors while the
hinges are being moved. Do not depend on the door magnets
to hold the doors in place while you are working.
6. Remove the parts for the top hinge as shown in Top Hinge
graphic. Lift the freezer door free from the cabinet.
7. Remove the parts for the center hinge as shown in the Center
Hinge graphic. Lift the refrigerator door free from the cabinet.
8. Remove the parts for the bottom hinge as shown in the
Bottom Hinge graphic.
NOTE: On some models, remove both the bottom hinge
assembly and the leveling foot.
Style 2 - Replace the Doors and Hinges
NOTE: Provide additional support for the doors while the hinges
are being moved. Do not depend on the door magnets to hold the
doors in place while you are working.
1. Replace the parts for the bottom hinge as shown. Tighten
screws. Replace the refrigerator door.
NOTE: On some models, install both the bottom hinge
assembly and the leveling foot.
2. Reconnect water dispenser tubing and wiring.
IMPORTANT: Do not intertwine the water tubing and wiring
bundles when reconnecting them.
3. Assemble the parts for the center hinge as shown and tighten
all screws. See Center Hinge graphic. Replace the freezer
door.
4. Assemble the parts for the top hinge as shown in the Top
Hinge graphic. Do not tighten the screws completely.
5. Line up the doors so that the bottom of the freezer door aligns
evenly with the top of the refrigerator door. Tighten all screws.
Final Steps (All Models)
1. Check all holes to make sure that hole plugs and screws are in
place. Reinstall top hinge cover. See Top Hinge graphic.
2. Replace the base grille. See Base Grille graphic.
3. Plug in refrigerator or reconnect power.
4. Reset the controls. See “Using the Controls.”
5. Return all removable door parts to doors and food to
refrigerator.
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.

9
Style 1 - Interior Dispenser Models
Door Removal and Replacement
Top Hinge
A. Top Hinge Cover
(on some models)
B. ⁵⁄₁₆" Hex-Head Hinge Screws
C. Top Hinge
D. Hinge Pin
A
B
C
D
Center Hinge
A. Center Hinge
B. ⁵⁄₁₆" Hex-Head Hinge Screws
A
B
Base Grille
A. Bottom Hinge
B. Screws
C. Leveling Leg (on some models)
Bottom Hinge
C
B
A

10
Style 2 - Exterior Dispenser Models
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
Door Removal and Replacement
Top Hinge
A. Top Hinge Cover
(on some models)
B. ⁵⁄₁₆ " Hex-Head Hinge Screws
C. Top Hinge
D. Hinge Pin
A
B
C
D
Center Hinge
A. Center Hinge
B.
⁵⁄₁₆ " Hex-Head Hinge Screws
A
B
Base Grille
Water Dispenser
Tubing Connection
A. Face of Fitting
A
Wiring Connection
A
A. Wiring Plug
A
A
A. Bottom Hinge
B. Screws
C. Leveling Leg (on some models)
Bottom Hinge
C
B
A

11
Adjust the Doors
IMPORTANT: To comply with American Disabilities Act (ADA)
guidelines, fully retract the rollers into the cabinet to lower the
refrigerator.
Door Closing
The base grille covers the leveling/roller assemblies located at the
bottom of the refrigerator cabinet. Before making adjustments,
remove the base grille and move the refrigerator to its final
location.
1. Remove the base grille. Grasp the grille firmly and pull it
toward you.
2. If you did not install the brake foot on the hinge side when you
unpacked the refrigerator, install the brake foot now. See
“Unpack the Refrigerator.”
3. Move the refrigerator to its final location.
NOTE: To allow the refrigerator to roll easier, raise the leveling
legs or brake feet off the floor by turning them
counterclockwise. The front rollers will be touching the floor.
4. Make sure the doors close easily. If you are satisfied with the
door opening and closing, skip steps 3 and 4. If the doors do
not close easily or the doors pop open, adjust the tilt.
Style 1 - Flat Door Models
■Use a socket driver to adjust the leveling screws. Turn the
leveling screw to the right to raise that side of the
refrigerator or turn the leveling screw to the left to lower
that side. It may take several turns of the leveling screws
to adjust the tilt of the refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws and
rollers which makes it easier to adjust.
Style 2 - Contour Door Models
■Use a ¹⁄₄" open-end wrench to turn both brake feet
clockwise. This will raise the front of the refrigerator tilting
it slightly downward to the rear. Turn both brake feet the
same amount.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the brake feet making
them easier to turn.
5. Open both doors again to make sure they close as easily as
you like and that they stay closed. If not, tilt the refrigerator
slightly more to the rear. It may take several more turns.
NOTE: To keep the refrigerator level, you should turn both
leveling screws or brake feet (depending on your model) the
same amount.
6. Replace the base grille.
Door Aligning
If the space between your doors looks uneven, you can adjust it
using the following instructions:
1. Pry off the top hinge cover.
2. Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.
3. Have someone hold the door in place or put a spacer between
the doors while you tighten the top hinge screws.
4. Replace the top hinge cover.
Install Air Filter
(on some models)
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use. On some models,
the air filter is already installed at the factory.
The air filter reduces the buildup of odors. This helps to maintain a
cleaner environment inside the refrigerator.
A. Brake foot
B. Front roller
A
B

12
Installing the Air Filter (on some models)
The filter should be installed behind the vented door, which is
located (depending on your model) along either the rear or left
interior wall near the top of the refrigerator compartment.
1. Remove the air filter from its packaging.
2. Lift open the vented door.
3. Snap the filter into place.
Air Filter Status Indicator (on some models)
Style 1 - Install Manual Air Filter Status Indicator
The filter comes with a status indicator, which should be activated
and installed at the same time the air filter is installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator, until
the bubble pops to activate the indicator.
3. Lift open the vented air filter door. On some models, there are
notches behind the door.
On models with notches:
■Slide the indicator down into the notches, facing outward.
NOTE: The indicator will not easily slide into the notches
if the rear bubble has not been popped.
■Close the air filter door, and check that the indicator is
visible through the rectangular hole in the door.
On models without notches:
■Store the indicator in a visible place you will easily
remember - either inside the refrigerator, or elsewhere in
your kitchen or home.
Style 2 - Air Filter Status on Electronic Control Display
The control panel displays the Air Filter status.
■GOOD - The air filter LED does not light up.
■REPLACE - The air filter LED lights up constantly when the
refrigerator door is open.
■EXPIRED - The air filter LED lights up constantly and flashes
when the refrigerator door is open.
After replacing the air filter, press and hold FILTERS RESET for
3 seconds. The filter icons will turn off. See “Using the Control(s).”
NOTE: At any filter status, pressing and holding FILTERS RESET
for 3 seconds will reset the air filter status to good and the air filter
LED will turn off.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months, or
when the status indicator air filter icon LED turns on and starts
flashing when the refrigerator door is opened.
To order a replacement air filter, contact us using the
assistance/service information following the warranty.
1. Remove the old air filter by squeezing in on the side tabs.
2. Remove the old status indicator.
3. Install the new air filter and reset the status indicator using the
instructions in the previous sections.
REFRIGERATOR USE
Using the Controls
Depending on your model, the control panel is located either at
the top front of the refrigerator compartment or on the dispenser
display. Follow the instructions specific to your model.
IMPORTANT:
■Wait 24 hours for your refrigerator to cool completely before
adding food. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer temperature
controls to a colder than recommended setting will not cool
the compartments any faster.
■The recommended setting should be correct for normal
household refrigerator use. The controls are set correctly
when milk or juice is as cold as you like and when ice cream is
firm.
■If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
Interior Dispenser Models
The control panel is located at the top front of the refrigerator
compartment.
For your convenience, the temperature control is preset at the
factory. When you first install your refrigerator, make sure the
control is still set to the recommended setting as shown.
Recommended Setting “3rd Snowflake”
MONTHS
REPLACE

13
Adjusting the Controls
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the following chart
as a guide.
■Press the TEMP button to display the desired number of
snowflakes (1 snowflake [least cold] to all snowflakes
[coldest]).
NOTE: Except when starting the refrigerator, do not adjust the
control more than one setting at a time. Wait 24 hours between
adjustments for the temperature to stabilize.
Cooling On/Off
■Press and hold TEMP for 3 seconds to turn cooling off. To turn
cooling back on, press and hold TEMP again for 3 seconds.
NOTE: Neither compartment will cool when the control is set to
OFF.
Additional Features
Filters Reset (on some models)
The Filters Reset control allows you to restart the filter status
tracking feature each time you replace the air filter or water filter.
■Press and hold FILTERS RESET for 3 seconds. The filter icons
will turn off. See “Install Air Filter” and “Water Filtration
System.”
Exterior Dispenser Models
The control panel is located above the exterior dispenser.
IMPORTANT: The display screen on the dispenser control panel
will turn off automatically and enter “sleep” mode when the
control buttons and dispenser levers have not been used for
2 minutes or more. While in “sleep” mode, the first press of a
control button will only reactivate the display screen, without
changing any settings. After reactivation, changes to any settings
can then be made. If no changes are made within 2 minutes, the
display will re-enter “sleep” mode.
■Touch any control button on the dispenser panel to activate
the display screen.
Adjusting the Controls
For your convenience, the temperature control is preset at the
factory. When you first install your refrigerator, make sure that the
control is still set to the recommended temperature setting
(3 snowflakes), as shown.
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the following chart
as a guide.
■Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made. The single
temperature control ranges from 1 snowflake (least cold) to
5 snowflakes (coldest). When adjusting temperature set
points, use the following chart as a guide.
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is
turned off.
■To turn cooling off, press and hold both TEMPERATURE
buttons at the same time for 3 seconds. When cooling is off,
“Cooling Off” will appear on the display screen.
■To turn cooling back on. Press and hold both TEMPERATURE
buttons at the same time for 3 seconds. When cooling is on,
“Cooling Off” will disappear from the display screen.
CONDITION/REASON: ADJUSTMENT:
REFRIGERATOR too warm REFRIGERATORControl
one setting higher
FREEZER too warm/too little ice FREEZER Control one
setting higher
REFRIGERATOR too cold REFRIGERATORControl
one setting lower
FREEZER too cold FREEZER Control one
setting lower
CONDITION: TEMPERATURE
ADJUSTMENT:
REFRIGERATOR or FREEZER
too cold Press the left-hand TEMPERATURE button to
adjust the temperature
one setting
less cold (2 snowflakes)
REFRIGERATOR or FREEZER
too warm Press the right-hand TEMPERATURE button to
adjust the temperature
one setting
colder (4 snowflakes)

14
Additional Features
Door Open Alarm
■The Door Open icon lights up whenever either door is opened.
■When either door is open for 5 minutes and cooling is on, an
alert tone will sound three times, and the Door Open icon will
flash seven times. This pattern will repeat every 2 minutes until
all the doors are closed properly. The feature then resets and
will reactivate when either door is left open again for
5minutes.
NOTES:
■To mute the audible alarm while keeping the doors open, such
as while cleaning the inside of the refrigerator, press any
button on the control panel. The alarm sound will be
temporarily turned off, but the Door Open icon will still be
displayed on the dispenser control panel.
■Both doors must be fully closed to turn off the Door Open
icon.
Fast Cool
The fast cool feature assists during times of high refrigerator use,
full grocery loads or temporarily warm room temperatures.
■Press FAST COOL to set the freezer and refrigerator to the
coldest temperature settings. Press FAST COOL again to
return to the selected temperature set point.
NOTES:
■The Fast Cool icon will be illuminated while the refrigerator
is in Fast Cool mode.
■The Fast Cool feature will turn off automatically after
24 hours.
Water Filter Status Light and Reset
The filter reset control allows you to restart the water filter status
tracking feature each time you replace the water filter. See “Water
Filtration System.”
■Press and hold WATER FILTER for 3 seconds, to reset the
water filter status to Good. The water filter LED will turn blue.
Air Filter Status Light and Reset
The filter reset control allows you to restart the air filter status
tracking feature each time you replace the air filter. See “Install Air
Filter.”
■Press and hold AIR FILTER for 3 seconds, to reset the air filter
status to Good. The air filter LED will turn blue.
Water Dispenser
IMPORTANT: After connecting the refrigerator to a water source
or replacing the water filter, flush the water system. Use a sturdy
container to depress and hold the water dispenser lever for
5 seconds, then release it for 5 seconds. Repeat until water
begins to flow. Once water begins to flow, continue depressing
and releasing the dispenser lever (5 seconds on, 5 seconds off)
until a total of 3 gal. (12 L) has been dispensed. This will flush air
from the filter and water dispensing system, and prepare the
water filter for use. Additional flushing may be required in some
households. As air is cleared from the system, water may spurt
out of the dispenser.
NOTES:
■Allow 24 hours for the refrigerator to cool down and chill
water.
■Dispense at least 1 qt (1 L) of water every week to maintain a
fresh supply.
■Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
Style 1 - Interior Dispenser Models
IMPORTANT: After 5 minutes of continuous dispensing, the
dispenser will stop dispensing water to avoid flooding. To
continue dispensing, press the dispenser paddle again.
To dispense water:
1. Hold a container under the dispenser spout while pressing the
dispenser pad.
2. Release the dispenser pad to stop dispensing.
Style 2 - Exterior Dispenser Models
IMPORTANT:
■The dispensing system will not operate when the refrigerator
door is open.
■The display screen on the dispenser control panel will turn off
automatically and enter “sleep” mode when the control
buttons and dispenser levers have not been used for
2 minutes or more. While in “sleep” mode, the first press of a
control button will only reactivate the display screen, without
changing any settings. After reactivation, changes to any
settings can then be made. If no changes are made within
2 minutes, the display will re-enter “sleep” mode.

15
To dispense water:
1. Press a sturdy glass against the water dispenser lever.
2. Remove the glass to stop dispensing.
The Dispenser Light
When you use the dispenser, the light will automatically turn on.
If you want the light to be on continuously, you may turn on the
light. The light icon LED will illuminate when the light is on.
ON: Press LIGHT/LOCK quickly to turn on the dispenser light.
OFF: Press LIGHT/LOCK quickly to turn off the dispenser light.
NOTES:
■If you unintentionally press and hold the LIGHT/LOCK button
for 3 seconds or longer, you will lock the water dispenser. If
this happens, press and hold LIGHT/LOCK for 3 seconds
again to unlock the water dispenser.
■The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see
“Troubleshooting” for more information.
The Dispenser Lock
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the refrigerator,
to the ice maker, or to the dispenser light. It simply deactivates the
controls and dispenser levers. To turn off the ice maker, see “Ice
Maker and Storage Bin.”
■Press and hold LIGHT/LOCK for 3 seconds to lock the
dispenser.
■Press and hold LIGHT/LOCK for 3 seconds again to unlock
the dispenser.
The lock icon LED will illuminate when the dispenser is locked.
Water Filtration System
Water Filter Status Light
The water filter status light will help you know when to change
your water filter. Follow the directions specific to your model.
Interior Dispenser Models
■When it is time to order a replacement water filter, the water
filter icon LED will light up whenever the refrigerator door is
open.
■When it is time to replace the water filter, the water filter icon
LED will light up and flash whenever the refrigerator door is
open.
If water flow to your water dispenser or ice maker decreases
noticeably, change the filter sooner. The filter should be replaced
at least every 6 months, depending on your water quality and
usage.
After changing the water filter, reset the status. Press and hold the
FILTERS RESET button for 3 seconds. When the system is reset,
the water filter icon LED will turn off.
Exterior Dispenser Models
The status of the water filter is determined by the number of days
since the water filter tracking feature was last reset.
■When the water filter status is good, between 0 and 167 days
(approximately), the Blue water filter LED lights up.
■When it is time to order a replacement water filter, between
168 and 181 days (approximately), the Yellow water filter LED
lights up.
■When it is time to replace the water filter, between 182 and
195 days (approximately), the Red water filter LED and the
words “Replace Filter” light up.
■When the water filter status is expired, the Red water filter LED
lights up, and the words “Replace Filter” light up and flash all
the time.
If water flow to your water dispenser or ice maker decreases
noticeably, change the filter sooner. The filter should be replaced
at least every 6 months, depending on your water quality and
usage.
After changing the water filter, reset the status. Press and hold the
WATER FILTER button for 3 seconds. When the system is reset,
the water filter status will return to good (0 days) and the Blue
water filter LED will light up.
ON
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.

16
Changing the Water Filter
1. Locate the water filter in the top-right corner of the refrigerator
compartment.
2. Lift open the filter cover door. The filter will be released and
then will be ejected as the door is opened.
3. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
4. Take the new filter out of its packaging and remove the covers
from the O-rings. Be sure the O-rings are still in place after the
covers are removed.
5. With the arrow pointing up, align the new filter with the filter
housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the filter
into place. You may need to press hard.
7. Flush the water system. See “Water and Ice Dispensers.”
Ice Maker
IMPORTANT: To avoid low ice production and poor quality ice,
flush the water system before turning on the ice maker. See
“Water Dispenser.”
■Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Allow 2 to 3 days for the
storage bin to fill completely following installation.
■The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
■If ice in the storage bin clumps together, break up the ice
using a plastic utensil and discard. Do not use anything sharp
to break up the ice. This can damage the ice bin and the
dispenser mechanism.
■Do not store anything on top of or in the ice maker or ice
storage bin.
Turning the Ice Maker On/Off
To turn the ice maker ON, simply lower the wire shutoff arm.
To manually turn the ice maker OFF, lift the wire shutoff arm to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.
Ice Production Rate
■The ice maker should produce approximately 8 to 12 batches
of ice per day under normal operation.
■To increase ice production, lower the freezer and refrigerator
temperature. See “Using the Control(s).” Wait 24 hours
between adjustments.
Ice Storage Bin
1. Turn off the ice maker before removing the ice storage bin to
serve ice or to clean the bin.
2. Wash the ice storage bin with mild soap and warm water.
3. Slide the ice storage bin under the ice maker, and push it
toward the back as far as it will go.
4. Lower the arm on the ice maker to the “on” position.
REFRIGERATOR
FEATURES
Your model may have some or all of these features.
Refrigerator Shelves
(Glass shelves on some models)
The shelves in your refrigerator are adjustable to match your
individual storage needs.
Storing similar food items together in your refrigerator and
adjusting the shelves to fit different heights of items will make it
easier to find the exact item you want. It will also reduce the
amount of time the refrigerator door is open, and save energy.
Shelves and Glass Shelves (on some models)
To remove and replace a shelf:
1. Remove items from the shelf.
2. Slide the shelf straight out to the stop.
3. Depending on your model, lift back or front of the shelf past
the stop. Slide shelf out the rest of the way.
4. Replace the shelf by sliding the back of the shelf into the track
in the wall of the cabinet.
5. Guide the front of the shelf into the shelf track. Be sure to slide
the shelf in all the way.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.

17
Fold Away Shelf (on some models)
To remove and replace a shelf:
1. To remove the entire shelf, tilt up the front of the shelf and
slide it out toward you.
2. To remove the front-half of the shelf, hold the front of the shelf
with one hand and press up in the center of the shelf. Then
push down and in on the shelf until it slides beneath the back
half of the shelf.
3. Replace the entire shelf by guiding it into the door liner and
pushing it inward until it stops. Then, tilt the front of the shelf
upward until the stopper is overcome and slide it in.
Meat Drawer
(on some models)
To remove and replace the meat drawer:
1. Slide meat drawer out to the stop.
2. Lift front of meat drawer with one hand while supporting
bottom of drawer with other hand. Slide drawer out the rest of
the way.
3. Replace the drawer by sliding it back in fully past the drawer
stop.
Meat Drawer Cover (on some models)
To remove and replace the meat drawer cover:
1. Remove the meat drawer.
2. Push the cover back to release the rear clips from the shelf.
Tilt the cover up at the front, and pull it forward.
3. Replace the meat drawer cover by fitting the notches and
clips on the cover over the rear and center crossbars on the
shelf.
4. Lower cover into place and pull the cover forward to secure
the rear clips onto the shelf.
5. Replace the meat drawer.
NOTE: In some models the meat pan moves sideways on the
shelf to allow for flexible positioning.
Meat Storage Guide
Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,
freeze the meat.
Fresh fish or shellfish.........................use same day as purchased
Chicken, ground beef, variety meats (liver)......................1-2 days
Cold cuts, steaks/roasts ..................................................3-5 days
Cured meats...................................................................7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.
Crisper
(on some models)
Crisper Drawers
To remove and replace the crisper drawer:
1. Slide the crisper drawer straight out to the stop. Lift the front
and slide the drawer out the rest of the way.
2. Replace the drawer by sliding the drawer in fully past the stop.
Crisper Cover
Style 1 - Plastic Cover
To remove and replace the crisper cover:
1. Remove the crisper(s).
2. Lift the front of the cover to remove the cover support. Then
lift the cover up and slide it out.
3. Replace the cover by fitting the cover tabs into lowest cabinet
slots and pushing them in. Lower the front retainers into place.
Style 2 - Glass Cover
To remove and replace the crisper cover:
1. Pull the glass straight out.
2. Replace the glass by pushing it straight in.

18
Crisper Humidity Control (on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) lets moist air out of the crisper for best storage of
fruits and vegetables with skins.
■Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.
Sort and keep berries in original container in crisper, or store in
a loosely closed paper bag on a refrigerator shelf.
■Vegetables with skins: Place in plastic bag or plastic container
and store in crisper.
HIGH (closed) keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
■Leafy vegetables: Wash in cold water, drain and trim or tear off
bruised and discolored areas. Place in plastic bag or plastic
container and store in crisper.
FREEZER FEATURES
Your model may have some or all of these features.
Wire Freezer Shelf
(on some models)
To remove and replace a wire shelf:
1. Remove the shelf by lifting the entire shelf slightly and moving
it all the way to the left-hand side. Tilt the right-hand side up
and out of the shelf supports.
2. Replace the shelf by inserting the left-hand end all the way
into the shelf supports. Then, lower the right-hand end of the
shelf and insert it into the shelf supports.
NOTE: The shelf should lower slightly and lock into place. If the
shelf does not appear stable, make sure both ends of the shelf are
inserted into the shelf supports.
Glass Freezer Shelf
(on some models)
To remove and replace a glass shelf:
1. Lift the front of the shelf to raise the shelf tabs up and out of
the opening in each shelf track. Slide the shelf out the rest of
the way.
2. Replace the shelf by tilting the back end downward to align
the back shelf tab under the track on each side of the freezer.
Gently push the shelf into the freezer until the two center shelf
tabs are positioned within the opening in each track. Lower
the shelf to rest on the shelf tracks.
Frozen Food Storage Guide
Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Seal the package
or container securely to avoid taste and odor transfer throughout
the product. Ice crystals inside a sealed package are normal. This
simply means that moisture in the food and air inside the package
have condensed, creating ice crystals.
Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2 to 3 lbs of food per cubic foot [907 to
1,350 g per L] of freezer space). Leave enough space in the
freezer for air to circulate around packages. The freezer door must
close tightly.
NOTE: For more information on preparing food for freezing, check
a freezer guide or reliable cookbook.
Important information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.

19
DOOR FEATURES
Your model may have some or all of these features.
Door Rails
The door rails may be removed for easier cleaning.
Snap on Door Rails (on some models)
To remove and replace the rails:
1. Remove the door rails by pushing in slightly on the front of one
end of the bracket while pulling out on the inside tab. Repeat
these steps for the other end.
2. Replace the rails by aligning the ends of the brackets with the
buttons on the sides of the door liner. Firmly snap bracket and
assembly onto the tabs above the shelf as shown.
Style 1 - Door Rails
Style 2 - Trivets
Door Bins
(on some models)
To remove and replace the racks/bins:
1. Remove the rack/bin by lifting it and pulling it straight out.
2. Replace the rack/bin by sliding it in above the desired support
and pushing it down until it stops.
Utility Compartment and Can Caddy
(on some models)
To remove and replace the utility compartment:
1. Remove the utility compartment by raising and holding the
cover up while lifting the utility compartment up and pulling it
straight out.
2. Replace the utility compartment by sliding it in above the
desired support and pushing it down until it stops.
To remove and replace the can caddy:
1. Hold the can caddy with one hand and pull up until it is
released from the door liner. Then, pull up on the caddy again,
until the stoppers have been overcome.
2. Pull the can caddy straight out to remove it from the door.
3. Replace the can caddy by aligning the grooves on the sides
with the pins in the door liner. Push up on the bottom of the
caddy until the stoppers have been overcome, and slide it fully
into the compartment.
REFRIGERATOR CARE
Cleaning
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
IMPORTANT:
■Because air circulates between both sections, any odors
formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid
odor transfer and drying out of food, wrap or cover foods
tightly.
■For stainless steel models, stainless steel is corrosion-
resistant and not corrosion-proof. To help avoid corrosion of
your stainless steel, keep your surfaces clean by using the
following cleaning instructions.
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

20
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, muriatic acid,
cleaning waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on exterior surfaces (doors and
cabinet), plastic parts, interior and door liners or gaskets. Do not
use paper towels, scouring pads, or other harsh cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3. Clean the exterior surfaces.
Painted metal: Wash painted metal exteriors with a clean,
soft cloth or sponge and a mild detergent in warm water.
Rinse surfaces with clean, warm water and dry immediately to
avoid water spots.
Stainless steel: Wash stainless steel surfaces with a clean,
soft cloth or sponge and a mild detergent in warm water.
Rinse surfaces with clean, warm water and dry immediately to
avoid water spots.
NOTE: When cleaning stainless steel, always wipe in the
direction of the grain to avoid cross-grain scratching.
4. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
■Remove the base grille.
■Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
■Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.
Changing the Light Bulbs
IMPORTANT:
■Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with an appliance bulb of the same size,
shape, and wattage.
■To ensure optimum refrigerator performance, replace light
bulbs as soon as they burn out.
Refrigerator Compartment Light
The light bulbs are located at the top of the refrigerator
compartment.
1. Unplug refrigerator or disconnect power.
2. Using both hands, squeeze inward on the sides of the light
shield, releasing it from the back of the compartment. Then,
move the shield toward the back to release it from the front of
the compartment.
3. Remove the light bulb(s) and replace it with a 40 watt
appliance bulb of the same size and shape.
4. Replace the light shield by inserting the front end into the
compartment and then pushing up until it snaps into place.
5. Plug in refrigerator or reconnect power.
Freezer Compartment Light (on some models)
1. Unplug the refrigerator or disconnect power.
2. Remove the light shield (on some models).
■Top of the freezer compartment - Slide the light shield
toward the back of the compartment to release it from the
light assembly.
3. Replace the burned-out bulb with an appliance bulb(s) no
greater than 25 watts.
4. Replace the light shield.
5. Plug in refrigerator or reconnect power.
Vacation and Moving Care
Vacations
If You Choose to Leave the Refrigerator On While You’re
Away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker, and is
connected to the household water supply, turn off the water
supply to the refrigerator. Property damage can occur if the
water supply is not turned off.
3. If you have an automatic ice maker, turn off the ice maker.
NOTE: Depending on your model, raise the wire shutoff arm to
OFF (up) position, or press the switch to OFF.
4. Empty the ice bin.
If You Choose to Turn Off the Refrigerator Before You
Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
■Turn off the water supply to the ice maker at least one day
ahead of time.
■When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position or press the switch to OFF,
depending on your model.
3. Turn off the Temperature control(s). See “Using the Control(s).”
4. Clean refrigerator, wipe it, and dry well.
5. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.