Whirlpool AKR290/WH User manual

Instruction Manual
AKR260/WH
AKR290/WH

This manual and the appliance itself provide important safety warnings, to be read and observed at all
es.
IMPORTANT SAFETY INFORMATION
INSTALLATION & USE
MAINTENANCE
Product Sp ecifica on & Technical Param eters
Model AKR260/WH
AKR290/WH
Rated Voltage 220-240V
Rated Power Frequency 50Hz
Light Power 2x40W
Motor Power 300W
Total Power 380W
Maximum suc on 450m3/hr (Non-restricted )
Diameter of Exhaust Pipe 120mm
Product Dimension AKR260/WH: D 470 x W 600 x H 130 mm
AKR290/WH: D 470 x W 900 x H 130 mm
Net Weight / Gross Weight AKR260/WH: 9.5kg / 10.5kg
AKR290/WH: 10.5kg / 11.5kg
Important Safety Informaon
1. Always disconnect the hood from the power supply before carrying out any installa on or
maintenance opera on the appliance.
2. Installa on must be carried out by a specialised technician, incompliance with the manufacturer’s
instruc ns and local safety regula ons.
3. Earthing of the appliance is compulsory.
4. Never use mul sockets and extension leads.
5. The electrical components must not be accessible to the user a er installa n.
6. Do not touch the hood with wet parts of the body or use it when barefoot.
7. Do not pull the appliance power cable to unplug it.
8. A er-sales service – do not repair or replace any part of the hood unless specifically indicated in
the manual. All other maintenance services must be carried out by a specialized technician.
9. When drilling the wall, make sure not to damage the electrical connec ns and/or pipes.
10. The ven la on ducts must always discharge to the outside.

11. The Manufacturer declines any liability for improper use or incorrect setting of the controls.
12. The appliance is not intended for use by children or persons with limited physical, sensory or
mental abilities or without experience and knowledge of it, unless they are under the supervision
of or instructed in its use by a person responsible for their safety.
13. Keep children away.
14. To reduce the risk of fire, only use a metal inlet duct.
15. Children must be supervised so that they do not play with the appliance.
16. The product must be disposed of in compliance with local regulations on waste disposal.
17. For further information on the treatment, recovery and recycling of this product, contact the
competent local office, the household waste collection service or the shop where you purchased
the appliance.
18. Regular cleaning and maintenance is essential for correct hood operation and good performance.
Frequently clean all encrustations from dirty surfaces to prevent the accumulation of grease.
Regularly clean or replace filters.
19. Do not “flambé” food under the hood. Naked flames could cause a fire.
20. The room must have adequate ventilation when the hood is used at the same time as appliances
operating on gas or other fuels.
21. The discharge air must not be eliminated in a duct used to remove fumes produced by appliances
operating on gas or other fuels, but must have a separate outlet. All the national regulations on
air discharge envisaged by art. 7.12.1 of CEI EN 60335-2-31 must be observed.
22. If the hood is used together with other appliances operating on gas or other fuels, the negative
pressure in the room must not exceed 4 Pa (4 x 10-5 bar). Therefore, make sure the room is
adequately ventilated.
23. Do not leave pans unattended when frying, since the cooking oil could catch fire.
24. Make sure the lamps are cold before touching them.
25. The hood is not a shelf, therefore do not overload or place objects on it.
26. Do not use or leave the hood without its lamps correctly installed - risk of electric shock.
27. Wear work gloves for all installation and maintenance operations.
28. The product is not suitable for outdoor use and is designed for domestic use only
29. The air sucked by the hood must not be eliminated through the same flue of the heating system
or other appliances using gas or other fuels.
30. The minimum distance is 750mm from the cooker hood to a gas hob, and is 650mm to an electric
hob. If the installation instructions for the cooker specify a greater distance between cooker and
hood, this distance must be observed.

Product Dimension and Components
AKR260/WH
Dimensions
Fig.1.
Fig.2.

Components
Ref
Qty
Components
1
2pcs
Grease filter
2
1pc
Baffle assembly
3
1pc
Hood body
4
7pcs
Screw
5
1pc
Rigid pipe
6
1pc
Blocking cover
7
1pc
Instruction manual
8
1pc
Warranty card

AKR290/WH
Dimensions
Fig.3.
Fig.4.

Components
Ref
Qty
Components
1
3pcs
Grease filter
2
1pc
Baffle assembly
3
1pc
Hood body
4
7pcs
Screw
5
1pc
Rigid pipe
6
1pc
Blocking cover
7
1pc
Instruction manual
8
1pc
Warranty card

Electrical Connection
1. Make sure the power voltage specified on the appliance rating plate is the same as the mains voltage.
This information can be found inside the hood,
2. Before reconnecting the hood circuit to the power supply and checking correct operation, always
make sure the power cable is correctly fitted and that it was NOT crushed in its housing during
installation. Make sure to have this operation carried out by a qualified technician in accordance with
all local codes and standards.
3. Turn off electrical power before installation
4. If supply cord is damaged, please call manufacturer for replacement to avoid any electrical hazards
5. Do not use plug and extension cord other than the one provided
6. Earthing of the hood is compulsory. Do not remove ground prong of the plug.
General Recommendations
Before use
Remove cardboard protection pieces, protective film and adhesive labels from accessories.
Check the appliance for any damage caused by transport.
During use
To avoid any damage do not place any weights on the appliance.
Do not expose the appliance to atmospheric agents.
This is a heavy product; the hood should only be lifted and installed by two or more people.
Installation
Position
1. The minimum installation height should not be less than 650mm and the recommended height is
700±50 mm. (Fig. 5.)
2. Avoid left-right or front-dropped inclination. Make sure hood is installed correctly with correct
alignment.
Mount the hood body
1. Drill the holes according to the distances indicated in Fig5,Fig.6 and Fig7.
2. Fix the support bracket to the wall and hook the hood on the support bracket for hooking it to the
wall. Adjust the distance between the hood and wall and align it in horizontal position to the wall
units. Adjust the hood horizontally using a level.
3. When the appliance has been adjusted, fully tighten the support using the screws. The hood comes
with all the materials required for installation on the majority of walls. All installations must be done

by qualified technician.
Remark:
Depth of the cabinet: 340mm
Height of the cabinet ＞130mm
FIg.6. AKR260/WH
FIg.5.
Min600mm
25mm
600-800mm
340mm
FIg.7. AKR290/WH
Min900mm
25mm
600-800mm
340mm

Fitting the filter
1. Insert the claws on both sides into the filter’s holes.
2. Put the filter by pushing the lock of filter. Press slightly and make sure it is fixed properly.
Fig 8. Fig 9.
Air extraction outwards
Fig 10.
1. When installing the ducted version, please connect the hood to chimney using rigid pipe ɸ120 to the
recess area of the air outlet adapter.
2. Fix the pipe in position using 2 screws from two sides of the air outlet adapter. Make sure the pipe is
secured.