Whirlpool AKTT600/IX Installation guide

Health & Safety, Use & Care, Installation Guide and
Online Warranty Registration Information
யݡщБ޽ăֹϡᄲځăщ྅޽ݑ
შ˯൳ܲዳྤ
Model ଐۂێ໔:$.77,;
$.77,;

( )
XP022560 2
Hood operation
Maintenance & Cleaning
Hood measurement
Wiring diagram
Replacing lamps
6
7
8
9
8
10
12
12
13
Before using the hood
15
16
16
17
18
14
Installation
Mounting method
Important safety instructions 1
3
4
5
3
吊掛安裝
CONTENTS

ISImportant afety nstructionsISImportant afety nstructions
1
These instructions shall also be available on website: www.whirlpool.com.hk
This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
All safety warnings are preceded by the attention symbol and the following terms:
All safety warnings specify the potential danger/warning to which they refer and indicate how to reduce the risk
of injury, damage and electrical shock resulting from incorrect use of the appliance. Comply with the following
KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
YOUR SAFETY ANDTHAT OF OTHERS IS HIGHLY IMPORTANT.
indicates a hazardous situation which, if not avoided, will cause serious injury.
indicates a hazardous situation which, if not avoided, could cause serious injury.
DANGER:
WARNING:
9.
8.
7.
6.
5.
4.
3.
2.
1.
instructions:
Installation or maintenance must be carried out by a specialized technician, in compliance with the
manufacturer’s instructions and local safety regulations.
The appliance must be disconnected from the power supply before carrying out any installation work.
Earthing of the appliance is compulsory.
The power supply cable must be long enough to permit connecting the appliance to the mains socket outlet.
Unplug the appliance with hands. Do not pull the power supply cable to unplug the appliance.
The electrical components must no longer be accessible to the user after installation.
Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
This appliance is not intended for use by persons ( including children ) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
must be replaced using genuine parts. All other maintenance services must be carried out by a specialized
10.
11.
12.
13.
technician.
Children must be supervised to ensure they do not play with the appliance.
When drilling through a wall or the ceiling, pay attention not to damage electric connections and/or pipes.
The ventilation ducts must always discharge to the outside.
burning gas
or other fuels, but must have a separate outlet. All national regulations governing extraction of fumes must
14.
15.
be observed.
The Manufactuer declines any liability for improper use or incorrect setting of the controls.
Regular cleaning and maintenance is essential to correct functioning and good performance of the appliance.
Frequently clean all encrustaions from dirty surfaces to prevent the accumulation of grease. Regularly clean

I S Important afety nstructions
2
There is a re risk if cleaning is not carried out in accordance with the instructions.
If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
There shall be adequate ventilation of the room when the range hood is used at the same time as appliances
The air must not be discharged into a ue that is used for exhausting fumes from appliances burning gas or
Regulations concerning the discharge of air have to be fullled.
burning gas or other fuels.
other fuels.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
CAUTION Accessible parts may become hot when used with cooking appliances.：
This appliance is intended for domestic use only.The product is not suitable for outdoor and commercial use.
Wear work gloves for all installation and maintenance operations.
Do not use or leave the hood without its lamps correctly installed-risk of electric shock.
Before touching the bulbs, rst ensure that they are cool.
eliminate heat congestion in the appliance.
When using more than three gas burners, the hood should be operating at power level 2 or greater. This will
Gas appliances must be used under the extractor hood only with pans resting.
The fume extractor hood must never be opened without the grease lters installed.
Failure to observe the instructions for cleaning the hood and replacing the lters may result in a re.
16.
17.
Do not ame under the range hood.
Do not leave frying pans unattended when frying, as the frying oil may catch re.

•Connect the power and switch on the motor and lighting system to check the operation.
a. Plastic collar x 1pc
b . Warranty card x 1pc and Instruction manual x 1pc
c. Installation Accessories Set x 1 set
( M4 x 8 screw x 2 pcs + 3/16 x 5/8 washer head screws x 4 pcs + 3/16 x 40mm screw x 4 pcs+ #6 x 1"
wooden screw x 8pcs)
(AKTT600/IX: Upper installation brackets x 2 pcs + Lower installation brackets x 2 pcs)
After unpacking the appliance, check for any transport damage. Do not install the appliance if it has been damaged.
In the event of problems, contactWhirlpool Customer Service. To prevent any damage, only remove the appliance
from its polystyrene foam packaging at the time of installation.
gas hob.(FIG. 2)
•Avoid left-right or front-dropped inclination.(FIG. 3)
•Packing materials (plastic bags, polystyrene, etc.) must be kept out of children’s reach, as they are potentially
•
•Parts supplied:
dangerous.
•
B U T Hefore sing he ood
3
Installation
( )FIG.1
( )FIG.3
( )FIG.2
mm057-056
2. Position
1. Location
•The smoke has to rise up to 25 mm from cook top in order to reach hood's0
Suggest to close window door before using hood .(FIG. 1)/
•.
3. Exhaust duct
•6 diameter exhaust duct is recommended to use in order to maximize"
suc .
•The installation height is measured vertically from center of aluminum
•The min height is 650mm and the max installation height is 750mm for
•Before installing the hood, please apply fast drying glue to the collar and
hood and exhaust duct to the plastic collar and seal with fast drying glue.
securely attach it to the top of cooker hood's vent lid. Install the cooker

M Mounting ethod
this appliance must be connected with earth wire.
Supply cord must be disconnected from power source before connection (to
the appliance).
M Mounting ethod
this appliance must be connected with earth wire.
Supply cord must be disconnected from power source before connection (to
the appliance).
4
1. Cut out an opening in the bottom of the cabinet by
following the dimensions in Fig. 1
3. Use (2) M4 x 8 screws to install the plastic collar.
4. Lift the hood into opening and ensure locking clip has
locked into position. (locking clip is located on left side
of hood body.) see Fig 2
5. 600mm Model only. Secure upper brackets to left and
right sides of the hood body by using (4) 3/16 x 5/8”
screws . Make sure the (2) captive nut screws holes on the
bracket are facing downward. Fig. 3
6. 600mm Model only. Place lower installation brackets
under upper installation brackets located on left and
right sides of hood body. Note: The wider portion of the
lower installation bracket should be at the bottom.
7. 600mm Model only. Install (4) 3/16x40 screws into
the captive nuts of upper installation brackets.
Tighten is no gap between the cabinet and front edge of
the hood. Fig. 4
8. 900mm Models only. Secure hood body to cabinet
base by (8) #6 x 1” wooden screws through the bottom of
range hood.Fig. 5
Fig 1
Front
Fig 2
Fig 5
Fig 3
Fig 4

5
0 I 0 I II III
Fan Speed
1
Lights On/Off
2
Fan Speed
Lights On/Off
1
2
Hood Operation
NOTE:
2. Please slide the control to the right position according to the control instruction.
If not, the Fan or lights might not operate properly.
1. Pull out the lter and turn on fan and light button to switch on the hood.
Fan and light will shut o when slide the lter in.
Fan and light will not operate when slide the lter in.

A. Hood Surface Maintenance
1. Please clean the hood surface regularly with mild detergent and wipe with a cotton cloth to prevent grease
from accumulating.
2. Please do not use abrasive or corrosive cleaning agent to clean the surface because this will damage the
surface.
3. It is recommended to use non corrosive stainless steel polisher to polish the surface after cleaning.
4. Please use soft cloth for polishing because it will make your hood surface shining.
5. Please do not use cleaning solutions that contain bleach ingredient.
B. Cleaning and Maintenance
1. Clean both exterior and interior of the hood for long lasting. Do not use abrasive cleanser.
in a dishwasher at low temperature and with a short cycle.
6.The oil cup in the center of the motor shell for holding grease can be detached and cleaned regularly.
7. It is recommended to turn on the hood before turning on the stove to avoid high temperature in the kitchen.
Always disconnect from power supply before cleaning.
M & Caintenance leaning
6

Unit mm：
Net Weights
Gross Weights
Hood Size W x D x H( )
Packing Size W x D x H( )
Voltage
Light
AKTT600/IX AKTT900/IX
12.2Kg
14.3Kg 16.6Kg
14.2Kg
Outlet pipe diameter
Model
LED 6W x2 (GU10,220V 50Hz)
220V,50Hz
598 x 315-480 x 410.8mm 898 x 315-480 x 410.8mm
6 inches
Specifications
7
H Mood easurement
980x374x420mm682x374x420mm

•Always disconnect the appliances from power supply before replacing lamps.
Please contactWhirlpool Customer Service to purchase new LED light for replacement.
R Leplacing amps
8
• Use protective gloves.
Never dismantle, repair or modify the appliance by yourself.
for anyone other than the above mentioned people to perform repair service.
Remove by turning bulb counter-clockwise. Note: Bulb does not unscrew; it turns 60 degrees,
stops and falls out.
the bulb or use a rubber/latex glove to grip the bulb and turn counter clockwise.
If bulbs are dicult to turn due to prolonged use, rmly attach a glass suction cup approximately the diameter of