Whirlpool AWO 5761 User manual

AU AWO 5761 PROGRAMME CHART
❉: optional / Yes : dosing required
1) For improved garment care spin speed is restricted to 1000 rpm in this programme.
2) In this programme default spin speed can be increased till 400 rpm. 5019 301 05696
Whirlpool is a registered trademark of Whirlpool USA
Programme Care
Labels Type of wash/Notes
Max
Load
Detergents and additives Special options Max
Spin
Speed
rpm
Tempe-
rature
°C
Softener Main
Wash Pre- wash Start
delay Easy
ironing Eco Pre wash Intensive rinse Rinse hold Variable
spin
Kg
Cotton
Normally to heavily soiled bed linen,table linen and
underwear, towels, shirts etc. made of cotton, coloured
cotton and linen.
For temperature selection, please respect the manufacturer's
recommendation on the care label.
With heavily soiled laundry the additional “Prewash” option can
be selected as well.
7.5 ❉Yes ❉❉❉❉❉❉ ❉ ❉ 1400 20 to 95
Synthetics
Normally soiled blouses, shirts, overalls etc.made of polyester
(Diolen, Trevira), polyamide (Perlon, Nylon) or blends with
cotton. 2.5 ❉Yes ❉❉❉❉❉❉ ❉ ❉1) 1000 1) 20 to 60
Daily load Slightly to normally soiled textiles made of cottonand/or
synthetics. 3.0 ❉Yes — ❉❉
—— ❉❉ ❉1400 30 to 60
Quick wash Shortly worn outer clothing made of cotton, polyester,
polyamide and blends with cotton. 3.0 ❉Yes — ❉❉
—— ❉❉ ❉1400 20 to 30
Delicates Curtains and delicate clothing, dresses skirts, shirts and blouses. 1.5 ❉Yes ❉❉——❉—❉❉1) 1000 1) 20 to 40
Wool Only woollens with a felt-free finish, labelled with the
woolmark and identified as machine washable.
If you select “Rinse Hold” do not leave items to soak for too long. 1.0 ❉Yes — ❉———— ❉❉1) 1000 1) 20 to 40
Handwash Textiles made of linen, silk, wool and viscose marked as
“handwashable”.
If you select “Rinse hold” do not leave items to soak for toolong.
A very gentle spin is used in this programme. 1.0 ❉Yes — ❉———— ❉❉2) 400 2) 20 to 30
Rinse & Spin — Same as the last rinse and the final spin in the “Cotton”
programme. 7.5 ❉——❉❉
—— ❉❉ ❉1400 —
Spin — In this programme spinning is intensive. Same as the spin cycle in
the “Cotton” programme. 7.5 ———❉———— — ❉1400 —
Short spin — In this programme spinning is gentle. Same as the spin cycle in the
“Wool” programme. 1.5 ———❉———— — ❉1) 1000 1) —
Drain — Drain only - no spinning. Alternative method of terminating
programme after “Rinse hold”. —————————— — — —
This washing machine is equipped with
automaticsafetyfunctionswhichdetect and
diagnose faults at an early stage and react
appropriately, e.g.:
A. “Water tap closed” indication
B. “Clean pump” indication
C. “Door locked” indication
D. “Aquasure” indication
E. Programme selector knob
F. Programme sequence indication
G. Temperature selection button
H. “Start/Pause” button
I. “Start/Pause” indication
J. “Start delay” button
K. “Start delay” indication/“Remaining
Time” display
L. “Reset” button
M. “Variable spin” button
Selectingany option the indication lightsup.
When the combination of programme,
additional options and temperature is not
possible, the indication lights switch off
automatically. Unsuitable combinations of
options are deselected automatically.
B
I
F
H
A C
J K LME
G
D
30105696GB.fm Page 1 Wednesday, July 6, 2005 5:38 PM
Black process 45.0° 100.0 LPI

5019 301 05696
Whirlpool is a registered trademark of Whirlpool USA
Add the detergent as described in the programme
table or in the chapter “Detergents and Additives”
in the booklet.
1. Turn the programme selector knob to the
desired programme and temperature.
2. Theremaining time display showsthe duration
of the chosen programme (in hours and minutes)
and after taking some seconds for calculating, the
indicationof the“Start/Pause” buttonis flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
Selecting any option the indication lights up.
When the combination of programme, additional
optionsandtemperatureisnotpossible,theindication
lights switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics”
and “Daily load” programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
“Eco” button
• The duration of the wash is extended and the
temperature reduced to save energy but
maintaining good washing results.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive rinse” button
• More water and a longer time in rinse cycle is added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
withoutprogressing tothefinalspin cycletoavoid
creasing and prevent colours from changing.
• Thisoption isparticularlyrecommendedfor the
programme“Synthetics”, “Daily load”and “Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indication is on.
Terminate the “Rinse hold” option:
• Press the “Rinse hold” button again; the
programmewillterminateautomatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the “Drain” programme and press the
“Start/Pause” button again when the indication
next to it is flashing.
“Variable spin” button
• Every programme has an automatic predefined
maximum spin speed.
DATA
Programme Temperature
(°C)
Load
(kg)
Approx.
Programme
Duration
(hours : minutes)*
Cotton 95 7.5 2:05
Cotton 60 7.5 2:25
Cotton 40 5.0 2:10
Synthetics 60 2.5 1:35
Synthetics 40 2.5 1:25
Daily load 40 3.0 1:05
Quick wash 30 3.0 0:35
Delicates 40 1.5 0:50
Wool 40 1.0 0:45
Handwash 30 1.0 0:45
Prewash cycle might increase programme duration. Consumption data in the home may vary in relation to the water supply
pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
• Press the button to set another spin speed.
• If the spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Start delay” allows to run the machine at the
consumer’sconvenience,forexampleatnightwhen
electricity is cheaper.
• Press the “Start delay” button to select the delay
time by 1 to 23 hours;
• Press the “Start/Pause” button.
The indication next to the “Start delay” button
lights up and goes off when the programme starts.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to the “Off/0”
position.
• Reselect the desired programme and options and
press “Start/Pause” button to start the programme.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 seconds -
the start delay time disappears from the
remaining time display, then
• either start the chosen programme by pressing
the “Start/Pause” button twice
• or turn the programme selector knob to the
“Off/0” position and choose another programme.
Open the tap and press the “Start/Pause” button.
The indication next to the “Start/Pause” button
lights up. The indications show the sequence
reached in the programme. After starting the
programme, the sequence indication runs from left
to right through Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding indication goes out.
The appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure that
they do not play with the appliance.
CAUTION:Ifthis appliance issupplied fromacord
extension set or electrical portable outlet device,
the cord extension set or portable outlet device
must be positioned so that it is not subject to
splashing or ingress of moisture.
“Water tap closed”
Theappliancehasno or insufficientwater supply. Open
the watertap; iftheindication still lights up,refer tothe
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Wastewaterisnotpumpedout. Checkwhetherthe
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Door locked”
As long as a washing programme is running, the
lamp lights up to show that the door cannot be
opened. When the indication goes off, the door can
be opened again.
“Aquasure”
Lighting up of the water stop indication can be caused
by a leak in the appliance orhose. Please refer tothe
“Troubleshooting Guide” in the Instructions for Use.
• The remaining time is on “0:00” and all the lights
of the programme sequence indication are off.
1. Turn the programme selector to the “Off/0”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Pressthe “Start/Pause” buttonagain. The new
programme continues at the same position
wherethepreviousprogrammewasinterrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme before
the end.
• Press the “Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
SAFETY
RED INDICATIONS
PROGRAMME END
CHANGE THE PROGRAMME, OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30105696GB.fm Page 2 Wednesday, July 6, 2005 5:38 PM
Black process 45.0° 100.0 LPI

5019 301 05696
Whirlpool is a registered trademark of Whirlpool USA
If you wish to connect
hot and cold water
supply (Fig.1):
1. Fix the red marked inlet hose at the hot
water tap and at the inlet valve with the red
filter on the rear side of machine.
2. Fix the other inlet hose at the cold water tap
and at the inlet valve with the blue filter on
the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position
(for example: cold fill into hot inlet valve and
viceversa).
If you wish to connect only the
cold fill follow the below
instruction (Fig.2):
1. You need a Y-piece connector. The
Y-piece connector can be ordered via our
Service Organization or purchased in a
specialized hydraulic component store.
2. Fix the Y-piece connector to the cold fill
tap.
3. Connect the two inlet valves present on
therear part of the machine tothe Y-piece
connector using the relative provider
hoses.
Make sure:
All connections are tightly fixed.
HOT / COLD FILL INSTRUCTION
Fig.1 Fig.2
Do not allow children to operate, crawl on, near or inside your
washer.
Note that during wash cycles, the surface temperature of the
porthole door may increase.
Close supervision of children is necessary when the appliance is
used near children.
30105696GB.fm Page 3 Wednesday, July 6, 2005 5:38 PM
Black process 45.0° 100.0 LPI