5019 301 10453
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
Closethedoorandturntheprogrammeselectortothe
desired programme and temperature. The indication
lamp next to the “Start/Pause” button flashes.
Push the button(s) of any option(s) desired - the
respective indication lights up.
Whenthecombinationofprogrammeandadditional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of
options are deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the Prewash option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
withoutprogressing tothe finalspincycle toavoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indication is on. The indication lamp
next to the “Start/Pause” button flashes.
Terminate the “Rinse hold” option :
• Press the “Start/Pause” button ; the
programmewillterminateautomaticallywith the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programmeselectorknob tothe“Drain”programme
and press the “Start/Pause” button .
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
CONSUMPTION DATA
Programme Temperature
(°C) Load
(kg) Water
(l) Energy
(kWh) Approx. Programme Duration
(hours : minutes)
Cotton 95 5.0 49*1.90 2:00
Cotton 60 5.0 44 0.95 2:10
Cotton with “Eco”** 60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50*0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the loadand the type of wash.
*To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
The “Start Delay” allows to run the machine at
the consumer’s convenience, for example at night
when electricity is cheaper. Do not use liquid
detergent when activating the start delay.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay
time by 1, 3, 6, 9 or 12 hours.
• Press the “Start/Pause” button .
The indication next to the “Start delay” button
flashes and goes off when the programme starts.
• Once having pressed the “Start/Pause” button
, the countdown of the time delay begins.
When the programme starts, the start delay
indicator light goes off and is replaced by the
programme sequence indication.
• After the “Start/Pause” button has been
pressed, the number of hours preselected can be
reduced by pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another
position or press the “Reset” button .
..after having pressed the “Start/Pause” button:
•Pressthe
“Reset” button for at least 3
seconds - the start delay indicator light goes out.
Open the tap and press the “Start/Pause” button
. The indication lamp next to the “Start/Pause”
button lights up. The programme sequence
indicatorshowsthecurrentprogrammephase,running
from left to right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the
corresponding indication goes out.
Before starting and after end of a programme, the
lamplights toshow thatthe doorcanbeopened.As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Wastewaterisnotpumpedout.Check whetherthe
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Service”
Lighting up of the “Service” indicationcanbe causedby
a fault in an electrical component. Refer to the
“TroubleshootingGuide”in yourInstructionsforUse;if
the fault persists, contact our After Sales Service.
• All the lights of the programme sequence
indicator are off, and the “Door open”
indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the “Start/Pause” button to pause
the programme. The light flashes.
2. Selectthe newprogramme(with temperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button again. The
new programme continues at the same position
wherethepreviousprogrammewasinterrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme
before the end.
•Pressthe“Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
