Whirlpool AWO/D 43136 User manual

GB AWO/D 43136 PROGRAMME CHART
5019 301 10290/A
Whirlpool is a registered trademark of Whirlpool USA
❉: optional / Yes : dosing required
1) For improved garment care, spin speed is restricted to 400 rpm in this programme.
2) Cold wash option is selectable only for the lowest temperature step of the programme.
Programme Care
Labels
Type of wash/Notes
- for temperature selection, respect the manufacturer’s recommendations on
the care label
Max
Load
kg
Detergents and additives Special options Max
Spin
Speed
rpm
Pre-
wash Main Wash Softener Start delay Eco Pre- wash Easy ironing Cold wash Rinse hold Variable
spin
Cotton
40 - 60 - 95 °C 40 - 60 - 95 °C
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts
etc. made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be selected as
well. 5.0 ❉Yes ❉ ❉❉❉ ❉ ❉2) ❉❉
1000
Synthetics
30 - 40 - 60 °C 30 - 40 - 60 °C
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira),
polyamide (Perlon, Nylon) or blends with cotton. 2.5 ❉Yes ❉ ❉❉❉ ❉ ❉2) ❉❉
1000
Delicates
30 - 40 °C 30 - 40 °C Curtains and delicate clothing, dresses skirts, shirts and blouses. 1.5 ❉Yes ❉❉
—❉—❉2) ❉❉ 1000
Daily load
40 °C 40 °C Slightly to normally soiled textiles made of cotton and/or synthetics. 3.0 — Yes ❉❉
—— ❉❉❉❉ 1000
Quick wash
30 °C 30 °C
Shortly worn outer clothing made of cotton, polyester, polyamide and blends
with cotton. 3.0 — Yes ❉❉
—— — ❉❉❉ 1000
Wool
Cold - 40 °C - 40 °C
Only woollens with a felt-free finish, labelled with the woolmark and identified
as machine washable.
If you select “Rinse Hold” do not leave items to soak for too long. 1.0 — Yes ❉❉
—— — ❉❉❉ 1000
Handwash
40 °C 40 °C
Textiles made of linen, silk, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin
is used in this programme. 1.0 — Yes ❉❉
—— — — ❉❉
400 1)
Lingerie
30 °C 30 °C This cycle is particularly suitable to treat delicate lingerie (use of a laundry net
strongly recommended). 1.0 — Yes ❉❉
—— — ❉❉❉
400 1)
Rinse & Spin —Same as the last rinse and the final spin in the “Cotton” programme. 5.0 — — ❉❉ —— — — ❉❉ 1000
Spin — In this programme spinning is intensive. Same as the spin cycle in the “Cotton”
programme. 5.0 — — — ❉—— — — — ❉1000
Gentle Spin —In this programme spinning is gentle. Same as the spin cycle in the “Wool”
programme. 1.0 — — — ❉—— — — — ❉1000
Drain —Drain only - no spinning. Alternative method of terminating programme after “Rinse
Hold”. —— — — ——— — — — — —
A. “Door open” indication
This washing machine is equipped with
automatic safety functions which
detect and diagnose faults at an early
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
and Start delay indicators
I. “Reset” button
J. “Start delay” button
K. Time display
DH
C
FIG
E
B
A
JK

5019 301 10290/A
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Turn the programme selector to the desired
programme and temperature.
2. The time display shows the duration of the
chosen programme (in hours and minutes), and
the “Start/Pause” indication lamp is flashing.
3. The indication lamp of the predefined spin
speed lights up.
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s)is notpossible, theindication lights switchoff
automatically. Unsuitable combinations of options are
deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
“Easy ironing” button
• Can be used together with “Cotton”,
“Synthetics” and “Daily load” programmes to
make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
“Cold wash” button
• Water is heated only up to 20°C.
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30° on
the care label.
• Selectable only on the lowest temperature step
of each programme.
“Rinse hold” button
• The laundry remains in the last rinse water
withoutprogressing to thefinalspin cycle toavoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at
thetime the“Anticrease” light inthe programme
sequence indication is on. The indication lamp
next to the “Start/Pause” button flashes.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the
programmewillterminateautomaticallywiththe
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the “Start/Pause” button.
CONSUMPTION DATA
Programme Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 95 5.0 49** 1.90 2:00
Cotton 60 5.0 44 0.95 2:10
Cotton with “Eco”*** 60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50** 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Lingerie 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the loadand the type of wash.
*The remaining time indicator can deviate fromthe values in the table, because it takes into account the household conditions
applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
The “Start Delay” allows to run the machine at the
consumer’sconvenience,forexampleatnightwhen
electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start Delay” button to select the delay
time by 1 to 23 hours;
• Press the “Start/Pause” button.
The indication light next to the “Start Delay”
button lights up and the countdown of the delay
time begins.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining programme time.
• Oncehaving pressedthe “Start/Pause”button,
thenumber of hours preselectedcan be reduced
by pressing again the “Start Delay” button.
To cancel the “Start Delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another
position or press the “Reset” button.
..after having pressed the “Start/Pause” button:
• Pressthe“Reset”button forat least3 seconds-the
start delay time disappears from the time display.
Open the tap and press the “Start/Pause” button.
Theindicationlampnexttothe“Start/Pause”button
lights up. The programme sequence indicator shows
the current programme phase, running from left to
right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme
time.Duetovariationsinloadandtemperatureofinlet
water,theremainingtimeisnewlycalculatedincertain
programme phases. If this is the case, an animation
appears on the time display.
Before starting and after end of a programme, the
lamplights to showthat thedoorcan beopened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indicationcanbe caused by
a fault in an electrical component. Refer to the
“TroubleshootingGuide”in yourInstructions forUse;if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Wastewaterisnotpumpedout.Check whetherthe
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence
indicator are off, and the “Door open”
indication lights up.
1. Turntheprogrammeselectortothe“Off/O”position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Selectthe newprogramme (withtemperature),
any options and another spin speed if you want.
3. Press the“Start/Pause” button again. The new
programme continues at the same position
wherethepreviousprogrammewasinterrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme before
the end.
•Pressthe“Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END