Whirlpool Cabrio WTW7300XW2 User manual

®
cabr,o
TOP-LOADING
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
LAVEUSE HAUTE
EFFICACITI_ A FAIBLE
CONSOMMATION D'EAU
AVEC CHARGEMENT
PAR LE DESSUS
GUIDE D'UTILISATION
ET D'ENTRETIEN
Table of Contents
WASHER SAFETY ......................................................... 2
WHAT'S NEW UNDER THE LiD? ................................. 3
CONTROL PANELAND FEATURES......................................4
Dispensers.......................................................................5
CYCLE GUIDE ............................................................... 6
USING YOUR WASHER ................................................ 8
Using Laundry Product Dispensers...............................9
Starting YourWasher......................................................9
WASHER MAINTENANCE .............................................. 11
TROUBLESHOOTING ...................................................... 13
WARRANTY ........................................................................18
ASSISTANCE OR SERVICE ...........................Back Cover
Table des Mati_res
S¢:CURIT¢: DE LA LAVEUSE ...................................... 19
QUOI DE NEUF SOUS LE COUVERCLE? ................ 20
TABLEAU DE COMMANDE
ET CARACTC:RISTIQUES .......................................... 21
Distributeurs.................................................................. 22
GUIDE DES PROGRAMMES ...................................... 23
UTILISATION DE LA LAVEUSE .................................. 26
Utilisation de distributeurs
de produits de lessive...................................................27
Mise en marche de la laveuse......................................27
ENTRETIEN DE LA LAVEUSE ........................................ 30
DF:PANNAGE ......................................................................32
GARANTIE ..........................................................................39
ASSISTANCE OU SERVICE ..............Couverture artiste
Para una version en espanol, visite www.whirlpool.com
Designed to use only HE High Efficiency
detergents.
Congue uniquement pour une utilisation
avec des d6tergents HE Haute efficacit6.
W10373816B
W10373817A - SP

WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injuryto persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. Ifthe hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach intothe washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where itwill be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user=repair instructionsthat you understand and
have the skills to carry out.
[] See "Electrical Requirements" located in the installation
instructions for grounding instructions.
this time. SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
2

WHAT'S NEW UNDER THE LID?
Cleaaiag with Less _ter
oo o_
Traditional agitator-style
washer Washer with low-water
washplate wash system
/\
The most striking difference in your new washer is the low-water
washplate wash system. The washer automatically adjusts the
water level to the load size--no water level selector is needed.
As the washer dampens and moves the load, the level of the
clothes will settle in the basket. This is normal, and does not
indicate that more clothes should be added.
IMPORTANT: You will not see a washer basket full of water
as with your past agitator-style washer.
When loading the washer with dirty laundry, fill it evenly
around the basket wall.
Automatic Load Size Sensing
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water level
for the load. This may take several minutes before water is
added. You will find a step-by-step description in the "Cycle
Status Lights" section.
You will hear the motor turn the basket in short pulses to
thoroughly wet the load. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
Choosiag the Right Detergent
Use only High Efficiency detergents. The package will be
marked "HE" or "High Efficiency." Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using
regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of detergent to use.
Use only High Efficiency (HE) detergent.
Concentrated Cleaniag
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils.
NormM Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the cycle, as the lid lock goes through a self-test. There
will be different kinds of humming and whirring sounds as the
washplate moves the load. And sometimes, you may hear
nothing at all, as the washer determines the correct water level
for your load or allows time for clothes to soak.
3

CONTROL P EL FEATURES
f
POWER
kcoBoost CYcle
Heavy not/Co d
Med ..... Lowd....... m/Cod I on SoftL°ud
Lioht CO d/Co d Extra Rinse 0 off
So Spir. Wash/R_nse Deep Fabric
_eve S_eed Temn Clear Softener
DisPense
I I
I
O
Not all features and cycles are available on all models.
J
OPOWER BUTTON
Press to turn the washer ON. Pressing once while the
washer is on will cancel the current cycle, pressing twice
will turn the washer OFR
WASH CYCLE KNOB
Turn the Wash Cycle knob to select a cycle for your laundry
load. See "Cycle Guide" for detailed descriptions of cycles.
TIME/STATUS DISPLAY
The Estimated Time Remaining display shows the time
required for the cycle to complete. Factors such as load size
and water pressure may affect the time shown in the display.
Overloading, unbalanced loads, or excessive suds may
cause the washer to adjust the cycle time, as well.
The Delay Wash indicator will light if you have set a delay
start to the cycle.
The Add a Garment indicator will let you know when it is still
possible to add items to the load.
When the cycle is complete, the DONE indicator will light
until the lid is opened.
OECO MONITOR
Your washer is specially designed to conserve energy
and water. Each cycle, along with any selected options, will
result in different energy and water usage. To use the Eco
Monitor, choose the best cycle for the load being washed,
then adjust temperature and spin speed options to improve
the energy usage within that cycle.
START/PAUSE BUTTON
Press to start the selected cycle; press again to pause
a cycle.
CYCLE SIGNAL BUTTON
Use this option to adjust volume of the signal that sounds at
end of cycle. A louder signal is helpful in removing items as
soon as cycle is complete.
@LID LOCK INDICATOR
This light indicates that the lid is locked and cannot be
opened. If you need to open the lid, press START/PAUSE.
The lid will unlock once the washer movement has stopped.
This may take several minutes if the load was spinning at
high speed. Press START/PAUSE again to restart the cycle.
OFABRIC SOFTENER DISPENSER SELECTOR
Press this button to set the Fabric Softener dispenser to
automatically add liquid fabric softener to the load at the
correct time.
CYCLE OPTIONS
Whenyou select a cycle, its default settings will light up.
SOIL LEVEL
Soil level (wash time) is preset for each wash cycle.
As you press the Soil Level pad, the cycle time (minutes)
will increase or decrease in the Estimated Time Remaining
display and a different wash time will appear.
For most loads, use the soil level that is preset with the
cycle you have chosen. For heavily soiled and sturdy
fabrics, press SOIL LEVEL to select more wash time, if
needed. For lightly soiled and delicate fabrics, press
Soil Level to select less wash time, if needed. A lower
soil level setting will help reduce tangling and wrinkling.
SPIN SPEED
This washer automatically selects the spin speed
based on the cycle selected. The preset speeds can be
changed. Not all spin speeds are available with all cycles.
• Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
• Slower spin speeds mean less wrinkling, but will leave
your load more damp.
WASH/RINSE TEMP
Temperature Control senses and maintains uniform
water temperatures by regulating incoming hot and
cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following the
garment label instructions, use the warmest wash water
safe for your fabric.
• Warm and hot water may be cooler than what your
previous washer provided.
• Even for cold wash settings, some warm water may
be added to the washer to maintain a minimum
temperature.
4

You may also add or remove options for each cycle.
Note that not all options can be used with all cycles,
and some are preset to work with certain cycles.
DEEP CLEAN
This option provides enhanced cleaning action for tough
stains. It will add additional time to the cycle. Deep Clean
should be started on a dry load only and must be selected
before the washer has started to fill.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
ECOBOOST
The EcoBoost option allows you to increase your energy
savings on your wash cycles. When this option is used,
the wash cycle will use cooler wash water than the
selected cycle and may increase the spin speed for
faster drying.
DISPENSERS
High Efficiency "HE" detergent dispenser
Add liquid or powdered HE detergent to this dispenser for
your main wash cycle.
Use only High Efficiency (HE) detergent.
Liquid chlorine bleach dispenser
This dispenser holds up to 3/4 cup (180 mL) liquid chlorine
bleach. The bleach will be automatically diluted and
dispensed at the optimum time during the the wash cycle.
This dispenser cannot dilute powdered bleach.
NOTE: Fill dispenser only with liquid chlorine bleach.
Liquid fabric softener dispenser
Pour measured liquid fabric softener into the liquid fabric
softener dispenser, if desired. It will dispense automatically
at the optimum time when the Fabric Softener option is
selected.
• Use only liquid fabric softener in this dispenser.
5

CYCLE GUIDE
Settings and options shown in bold are default settings for that cycle.
For best fabric care, choose the cycle that best fits the load being washed.
If using the Eco Monitor, adjust the temperature and spin speed within that cycle to improve energy usage.
Not all cycles and options are available on all models.
Items to wash:
Lightly soiled
garments
Machine-wash
silks, hand-wash
fabrics and wool
Normally soiled
sheets
Towels and
terrycloth items
No-iron fabrics
Cottons, linens,
and mixed garment
loads
Brightly or dark
colored casual
garments
Large items such as
sleeping bags, small
comforters, jackets
Sturdy fabrics,
colorfast items
Cycle: Wash!Rinse
Temperature: Options:
Hot/Cold High Heavy Deep Clean
Warm/Warm Medium Normal Extra Rinse
Warm/Cold Low Medium Fabric Softener
Cold/Cold Light
Quick
Wash
Handwash/
Delicate
Sheets
Towels
Perm
Press/
Casual
Normal
Darks/
Colors
Bulky
Items
Heavy
Duty
Available i Cycle Details:
Warm/Cold Medium Heaw Deep Clean
Warm/Warm Low Normal Extra Rinse
Cold/Cold Medium Fabric Softener
Light
Hot/Cold High Heavy Extra Rinse
Warm/Warm Medium Normal EcoBoost
Warm/Cold Low Medium Fabric Softener
Cold/Cold Light
Hot/Cold High Heavy Deep Clean
Warm/Warm Medium Normal Extra Rinse
Warm/Cold Low Medium EcoBoost
Cold/Cold Light Fabric Softener
Hot/Cold High Heavy Deep Clean
Warm/Warm Medium Normal Extra Rinse
Warm/Cold Low Medium EcoBoost
Cold/Cold Light Fabric Softener
Hot/Cold High Heavy Deep Clean
WarmANarm Medium Normal Extra Rinse
Warm/Cold Medium EcoBoost
Cold/Cold Light Fabric Softener
Hot/Cold High Heavy Deep Clean
Warm/Warm Medium Normal Extra Rinse
Warm/Cold Low Medium EcoBoost
Cold/Cold Light Fabric Softener
Hot/Cold Medium Heavy Extra Rinse
Warm/Warm Low Normal EcoBoost
Warm/Cold Medium Fabric Softener
Cold/Cold Light
Hot/Cold High Heavy Deep Clean
Warm/Warm Medium Normal Extra Rinse
Warm/Cold Low Medium EcoBoost
Cold/Cold Light Fabric Softener
Use this cycle to wash small loads of
2-3 lightly soiled garments that are
needed in a hurry. This cycle combines
a fast agitation, a shortened wash time,
and a high-speed spin to shorten
drying times.
Use this cycle for machine washable
delicate garments. This cycle uses
intermittent wash action with cool water
and slow spin to gently care for fine
washables and avoid shrinkage. Place
small items in mesh bags before washing.
Use this cycle to wash bed sheets. This
cycle uses extra water and a special
wash action to reduce tangling. On some
models, soil level defaults to Medium.
This cycle defaults to a warm wash and
medium spin speed. Hotter temperatures
help remove soils and odors; faster
spin speeds will reduce drying times.
On some models, soil level defaults to
Medium.
Use this cycle for lightly soiled office
wear. The cycle uses a warm wash, a
cooldown, and medium spin speeds for
better wrinkle performance.
Use this cycle to clean normally soiled
cottons and mixed fabric loads. Default
settings can be adjusted as needed.
On some models, soil level defaults to
Medium.
Cold water temperatures are used
to maintain dark dyes. Normal wash
action and medium wash time is preset.
Settings can be adjusted as needed.
On some models, soil level defaults
to Medium.
This cycle is designed for oversized
items that do not easily absorb water,
such as comforters, pillows, and poly-
filled jackets. The cycle uses an initial
soak to thoroughly saturate the item(s).
Use this cycle for heavily soiled or
sturdy cotton items. This cycle combines
high-speed wash action, longer wash
time, and extra high-speed spin to shorten
drying times. Adjust temperature settings as
needed.
6

CYCLE GUIDE
Settings and options shown in bold are default settings for that cycle.
For best fabric care, choose the cycle that best fits the load being washed.
If using the Eco Monitor, adjust the temperature and spin speed within that cycle to improve energy usage.
Not all cycles and options are available on all models.
Items to wash:
Soiled white
fabrics
Heavily soiled
fabrics
Cyc,ei
Whites
Soak
Wash/Rinse
Temperature: Available
nntinn_:
Hot/Cold High Heavy Deep Clean
Warm/Warm Medium Normal Extra Rinse
Warm/Cold Low Medium EcoBoost
Cold/Cold Light Fabric Softener
Warm/Cold No Spin Heavy EcoBoost
Cold/Cold Normal
Medium
Light
Cycle Details:
This cycle adds liquid chlorine bleach to
the load at the proper time for improved
whitening of soiled white fabrics.
Use this cycle to soak small spots of
set-in stains on fabrics. After time has
expired, washer will drain, but will not
spin and a tone will sound. To set a
follow-up cycle, add additional detergent
and select a cycle based on fabric type.
No clothes in Clean No Spin EcoBoost Use once a month to keep the inside
washer Washer of the washer fresh and clean. Higher
with water levels and Affresh work together
Affresh TM to thoroughly clean the washer interior.
For models with separate cycle knob positions for Rinse & Spin and Drain & Spin:
Swimsuits, items
that need rinsing
only
Wet load of
clothes
Rinse &
Spin
Drain &
Spin
Warm/Cold High Extra Rinse
Warm/Warm Medium EcoBoost
Cold/Cold Low Fabric Softener
For models with a Rinse/Drain & Spin cycle position:
Swimsuits, items
that need rinsing
only
High
Medium
Low
Wet load of
clothes
Rinse/D ;_:_!
& Spin
R _s4/Drain
& Spin
Warm/Warm High Extra Rinse
Warm/Cold Medium EcoBoost
Cold/Cold Low Fabric Softener
High
Medium
Low
This cycle uses a high-speed spin.
For some fabrics, you may wish to set
the spin speed to a lower setting.
Use this cycle to spin excess water
out of a load. This cycle drains the water
and spins at a high speed. Spin speed
is adjustable.
This cycle uses a high-speed spin.
For some fabrics, you may wish to set
the spin speed to a lower setting.
To select, choose Rinse/Drain & Spin
and turn off Extra Rinse. Use this cycle
to spin excess water out of a load. This
cycle drains the water and spins at a
high speed. Spin speed is adjustable.
7

USING YOUR WASHER
Fire Hazard
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1, Sort and prepare your laundry
• Empty pockets. Loose change, buttons, or any small object
can pass under the impeller and become trapped, causing
unexpected sounds.
• Sort items by recommended cycle, water temperature,
and colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing; heat can
set stains into fabric.
• Treat stains promptly.
• Close zippers, fasten hooks, tie strings and sashes.
Remove non-washable trim and ornaments.
• Mend rips and tears to avoid further damage to items
during washing.
Helpful Tips:
• When washing water-proof or water-resistant items, load
evenly. See "Cycle Guide" for tips and more information on
using the Bulky Items cycle.
• Use mesh bags to help prevent tangling when washing
delicate or small items.
• Turn knits inside out to avoid pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up
lint from towels, rugs, and chenille fabrics.
NOTE: Always read and follow fabric care labels instructions
to avoid damage to your garments.
8
Load garments in loose heaps evenly
around basket wall. Try mixing different
sized items to reduce tangling.
IMPORTANT." Items need to move freely
for best cleaning and to reduce wrinkling
and tangling.

Using Laundry Product Dispensers
Add HE detergent to dispenser
Detergent dispenser
Add a measured amount of HE
detergent into detergent dispenser.
IMPORTANT: Use only High Efficiency detergents. The package
will be marked "HE" or "High Efficiency." Low-water washing
creates excessive sudsing with a regular non-HE detergent.
Using regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of detergent to use.
NOTE: If using an Oxi laundry boost product, add to the
detergent dispenser.
HELPFUL TIP: See "Washer Maintenance" for information on
recommended method of cleaning washer dispensers.
to dispenser
Pour a measured amount of liquid
fabric softener into dispenser; always
follow manufacturer's directions for correct amount of
fabric softener based on your load size. Then select
Fabric Softener option.
IMPORTANT: Fabric Softener option must be selected
to ensure proper distribution at correct time in cycle.
Do not overfill or dilute. Overfilling dispenser will cause
fabric softener to immediately dispense into washer.
If Extra Rinse option is selected, fabric softener will be
dispensed in the last rinse.
NOTE: Do not use liquid fabric softener dispenser balls in
this washer. They will not dispense correctly.
Starting Your Washer
6, Press POWER to turn on washer
POWER
Do not overfill, dilute, or use more than 3/4 cup (180 mL).
Do not use color-safe bleach or Oxi products in the same
cycle with liquid chlorine bleach.
9

TOWELS
SHEETS
handwo h
DELICATE
COLORS
BULKYITEMS
HEAVYDUTY
WHITES
QUICKWASt
RINSE CLEAN
DRAIN SOAK WASHER
& SPIN with _1'8,_1
Turn cycle knob to choose your wash
cycle. Estimated Time Remaining
will light up with a cycle time. You may
notice time adjusting during the cycle.
This is normal.
If you do not want to begin a cycle
immediately, you may choose the
DELAY WASH option.
To choose a delay time:
1. Press DELAY WASH button
to select desired delay time.
2. Press START/PAUSE to set the
delay. The delay countdown has
started when the START/PAUSE
light stops blinking.
Est. Time Remaining
To cancel delaying a cycle:
1. Press START/PAUSE again to begin a wash cycle
immediately.
IMPORTANT: When delaying a cycle, use liquid HE detergent
only in the dispenser. Powdered detergents may absorb
moisture from a previous cycle and clump before the wash
cycle begins.
8, Select cycle settings, if desired
Heavy Hot/Cold
Normal High Warm/Warm
Medium Medium Warm/Cold
Lght Low Cod/Cod
Soil
Level Spin Wash/Rinse
Speed Temp
Once you select a cycle, the default settings for that cycle will
be lit. Press the cycle settings buttons to change the Soil Level,
Spin Speed, and Wash/Rinse Temperature, if desired. Not all
settings are available with all cycles.
NOTE: Always read and follow fabric care labels instructions
to avoid damage to your garments.
Wash Temp Suggested Fabrics
;;:::Some cold water is added to save Whites and pastels
energy. This will be cooler than Durable garments
your hot water heater setting. Heavy soils
Warm
;: Some cold water will be added, so Bright colors
this may be cooler than what your ;_Moderate to light soils
previous washer provided.
Cold ;:
Warm water may be added to ;;:::Dark colors that
assist in soil removal and to help ;;::bleed or fade
dissolve detergents, ili Light soils
10

9, Select cycle options
EcoBoost
Extra Rinse _
@@
Deep Fabric
Clean Softener
Dispenser
Cycle
Signal
Loud
Soft
Off
Lid Lock
Select any other cycle options you may wish to add, if not
previously set. Some cycles will automatically add certain
options such as Deep Clean or Extra Rinse. These may be
turned off, if desired.
NOTE: Not all options are available with all cycles.
1 0, Press and hold START/PAUSE
to begin wash cycle
START
Pause
Press the START/PAUSE button to start the wash cycle. Filling
is delayed for several minutes while load balance is sensed.
When the cycle has finished, the DONE indicator will light
and the end of cycle signal will sound (if set). Promptly remove
garments when cycle is done to prevent odor, reduce wrinkling,
and rusting of metal hooks, zippers, and snaps.
Unlocking the lid to add garments
If you need to open the lid to add 1 or 2 missed garments,
you may do so while the Add a Garment indicator is lit.
Press START/PAUSE; the lid will unlock once the washer
movement has stopped. This may take several minutes
if the load was spinning at high speed. Then close lid and
press START/PAUSE again to restart the cycle.
If lid is left open for more than 10 minutes the water will
pump out.
Delay in water fill
Filling is delayed for 2 to 3 minutes to check for load unbalance.
You will hear the hum of the spin prior to filling. This is normal
operation.
WASHER r INTENANCE
rWATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
f CLEANING YOUR WASHER
Keep your washer as clean and fresh as your clothes.
To keep washer interior odor-free, follow this recommended
monthly cleaning procedure:
1. Make sure the washer is empty.
2. Using recommended AFFRESH ®washer cleaner,
add one tablet to washer drum
OR
If using liquid chlorine bleach, add 1 cup (250 mL) to
liquid chlorine bleach dispenser.
Jf
\
IMPORTANT: Do not add detergent to CLEAN
WASHER with AFFRESH TMcycle. Do not use more than
recommended amount of bleach to avoid damaging
product over time.
3. Close washer lid.
4. Press POWER.
5. Select CLEAN WASHER with AFFRESW Mcycle.
6. Press START/PAUSE. Water will pour into washer
for a moment and pause, lid will lock, then cycle
will continue.
NOTE: For best results, do not interrupt cycle. If cycle must
be interrupted, press START/PAUSE twice and run a RINSE
AND SPIN cycle to ensure cleaner or bleach have been
rinsed from washer.
To clean exterior:
1. Use a soft, damp cloth or sponge to wipe up any spills.
2. Use all-purpose surface cleaner, if needed.
IMPORTANT: To avoid damaging the washer's finish,
do not use abrasive products.
11

CLEANING YOUR DISPENSERS
You may find laundry product residue leftover in your
dispensers. To remove residue, wipe with a damp cloth
and towel dry.
NON=USE AND VACATION CARE
Operate your washer only when you are home.
If moving, or not using your washer for a period of time,
follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due
to water pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE AND SPIN cycle for about 30 seconds
to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
f
1.
2.
3.
4.
5.
6=
7.
TRANSPORTING YOUR WASHER
Shut off both water faucets. Disconnect and drain water
inlet hoses.
If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
Disconnect drain from drain system.
Unplug power cord.
Place inlet hoses inside washer basket.
Drape power cord and drain hose over the console
and secure with masking tape.
Place foam packing ring from original shipping materials
back inside washer. If you do not have packing ring,
place heaw blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in
new location.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through BULKY ITEMS cycle to clean
washer and remove antifreeze, if used. Use only HE
High Efficiency detergent. Use half the manufacturer's
recommended amount for a medium-size load.
12

TROUBLESHOOTING
fFirst try the solutions suggested here or visit our website at www.whirlpool.com/help
for assistance and to possibly avoid a service call.
If you experience
Vibration, rocking, or
"walking"
Vibration during spinning
or washer stopped with
all dial lights flashing
Feet may not be in contact with the
floor and locked.
Washer may not be level.
Load could be unbalanced.
Front and rear feet must be in firm contact with floor, and washer
must be level to operate properly. Jam nuts must be tight
against the bottom of the cabinet.
Check floor for flexing or sagging. Hfflooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See "Level the Washer" in the "hstallation hstructions".
Load dry items in loose heaps evenly around basket wall.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Avoid washing single items. Balance a single item such as a
rug or jeans jacket with a few extra items. Hfthe dial is flashing,
redistribute the load, close the lid, and press START/PAUSE.
Use Bulky Htemscycle for oversized, non-absorbent items
such as comforters or poly-filled jackets. Other items are
not appropriate for Bulky Htemscycle. See "Cycle Guide".
Htemor load not suitable for selected cycle. See "Cycle Guide"
and "Using Your Washer" in this "Use and Care Guide".
Clicking or metallic
noises
Gurgling or humming
Humming
Objects caught in washer
drain system.
Washer may be
draining water.
The washer is sensing the
load size.
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump.
Htmay be necessary to call for service to remove items.
Htis normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket.
Htis normal to hear the pump making a continuous humming sound
with periodic gurgling or surging asfinal amounts of water are
removed during the spin/drain cycles.
You may hear the hum of the sensing spins after you have started
the washer. This is normal. Sensing spins will take several minutes
before water is added to the washer.
Check the following for
proper installation: Washer not level.
Fill hoses not attached tightly.
Fill hose washers
Drain hose connection
Check household plumbing for leaks
or clogged sink or drain.
Washer not loaded as
recommended.
Water may splash off basket if washer is not level.
Tighten fill-hose connection.
Make sure all four fill hose flat washers are properly seated.
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub.
Do not place tape over drain opening.
Water can backup out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe,
water pipes, and faucets.)
An unbalanced load can cause basket to be out of alignment
and cause water to splash off tub. See "Using Your Washer"
for loading instructions.
Not enough water
in washer Load not completely covered
in water. This is normal operation for an HE low-water washer. The load will not be completely unden._/ater.The washer senses load sizes and
adds correct amount of water for optimal cleaning. See "What's
New under the Lid."
IMPORTANT: Do not add more water to washer. The added water
lifts the load off the impeller, resulting in less cleaning. J
13

TROUBLESHOOTING
Washer won't run or fill,
washer stops working
k.
Check for proper water supply. Both hoses must be attached and have water flowing to
inlet valve.
Both Hot and Cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water flow;)
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
fmfyou experience
Washer won't run or fill,
washer stops working
(cont.)
Possibme Causes
Check proper electrical supply.
Normal washer operation.
Washer may be tightly packed.
Not using HE detergent or using too
much HE detergent.
Somution -'_
Plug power cord into a grounded 3 prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset atripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle.
Do not interrupt cycle.
Washer may be stopped to reduce suds.
The washer senses the dry load with short spins that may take
2 to 3 minutes before water is added. You may hear the hum
of the spins. This is normal.
Remove several items, rearrange load evenly in basket and add
detergent. Close lid and press START/PAUSE.
Do not add more than 1 or 2 additional items after cycle
has started.
Do not add more water to the washer.
Only use HE detergent. Suds from regular detergents can slow
or stop the washer. Always measure detergent and following
detergent directions based on your load requirements.
To remove suds, cancel cycle. Select DRAIN & SPIN. Select your
cycle. Press START/PAUSE. Do not add more detergent.
Washer not draining/ Empty pockets and use garment [_ags Small items may have been caught in pump or between basket
spinning, loads are still for small items, and tub, which can slow draining.
k,_et j
14

TROUBLESHOOTING
Washer not draining/
spinning, loads are
still wet (cont.)
Incorrect or wrong
wash or rinse
temperatures
Load not rinsed
Sand, pet hair, lint, etc.
on load after washing
Load is tangling
k.
Using cycles with a lower spin speed.
Washer may be tightly packed or
unbalanced.
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than 4.5"
(114 mm).
Not using HE detergent or using too
much HE detergent.
Check for proper water supply.
Energy saving controlled
wash temperatures.
Check for proper water supply.
Not using HE detergent or using too
much HE detergent.
Washer may be tightly packed.
Fabric softener option not selected.
Heavy sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Washer not loaded as recommended.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment.
Tightly packed loads may not allow the washer to spin correctly,
leaving the load wetter than normal. Evenly arrange the wet load
for balanced spinning. Select DRAIN & SPIN to remove excess
water. See "Using Your Washer" for loading recommendations.
Check drain hose for proper installation. Use drain hose
form and securely attach to drainpipe or tub. Do not tape
over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose.
Suds from regular detergent or using too much detergent can
slow or stop draining or spinning. Use only HE detergent.
Always measure and follow detergent directions for your
load. To remove extra suds, Select RINSE & SPIN. Do not
add detergent.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star washers may use cooler wash and rinse water
temperatures than your previous washer. This includes
cooler hot and warm washes.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer maybe clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can cause the washer
to operate incorrectly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
The washer is less efficient at rinsing when load is tightly
packed.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started.
When using fabric softener, be sure the Fabric Softener option
is selected.
Add an Extra Rinse to the selected cycle.
Load garments in loose heaps evenly around the basket wall.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed. .,2
15

TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help
for assistance and to possibly avoid a service call.
Load is tangling (cont.) Wash action and/or spin speed too
fast for load.
Not cleaning or Wash load not completely
removing stains covered in water.
Added more water to washer.
Washer not loaded as recommended.
Odors
Not using HE detergent or using too
much HE detergent.
Not using correct cycle for fabric type.
Not using dispensers.
Not washing like colors together.
Monthly maintenance not done as
recommended.
Not using HE detergent or using too
much HE detergent.
Fabric Damage Sharp items were in pockets during
wash cycle.
Strings and straps could have tangled.
Htemsmay have been damaged before
washing.
Fabric damage can occur if the load is
tightly packed.
Select a cycle with a slower wash action and slower spin speed.
Note that items will be wetter than when using a higher speed spin.
Washer senses load size and adds correct amount of water.
This is normal and necessary for clothes to move.
Do not add additional water to washer. Additional water lifts
the laundry off the impeller, resulting in less cleaning.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Add only 1 or 2 garments after washer has started.
The suds from regular detergent can prevent washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
Use a higher soil level cycle option and warmer wash
temperature to improve cleaning.
Hfusing Quick Wash cycle (on some models), wash only a
few items.
Use Whites and Heavy Duty cycle for tough cleaning.
See the "Cycle Guide" to match your load with the best cycle.
Use dispensers to avoid chlorine bleach and fabric softener
staining.
Load dispensers before starting a cycle.
Avoid overfilling.
Do not add products directly onto load.
Wash like colors together and remove promptly after the cycle
is complete to avoid dye transfer.
Run the Clean Washer cycle with AFFRESH TM monthly.
See "Cleaning Your Washer" in "Washer Maintenance".
Unload washer as soon as cycle is complete.
Use only HE detergent. Be sure to measure correctly.
Always follow the detergent directions.
See "Cleaning your Washer" section.
Empty pockets, zip zippers, and snap or hook fasteners before
washing to avoid snags and tears.
Tie all strings and straps before starting wash load.
Mend rips and broken threads in seams before washing.
Load garments in loose heaps evenly around the basket wall.
Load items should move freely during wash to avoid damage,
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer is started.
Always read and follow garment manufacturer's care label
instructions. See the "Cycle Guide" to match your load with
the best cycle.
Garment care instructions may not
have been followed.
16

TROUBLESHOOTING
rFirst try the solutions suggested here or visit our website at www.whirlpool.com/help
for assistance and to possibly avoid a service call.
Fabric Damage (cont.)
Incorrect dispenser
operation
Liquid chlorine bleach may have been
added incorrectly.
Clogged dispensers or laundry
products dispensing too soon.
Liquid chlorine bleach not
used in dispenser.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Do not overfill dispenser. Overfilling causes immediate dispensing.
Always select Fabric Softener option to assure proper dispensing.
Load dispensers before starting a cycle.
Htis normal for small amounts of water to be remain in dispenser at
the end of the cycle.
Homes with low water pressure may result in residual powder in the
dispenser. To avoid, select a warmer wash temperature if possible,
depending on your load.
Use only liquid chlorine bleach in the Bleach dispenser.
oL (overloaded)
appears in display
uL (unbalanced load)
appears in display
LF (too long to fill)
appears in display
Ld (too long to drain
water ) appears in
display
HC (Hot and Cold
hoses reversed)
appears in display
Sd (Excess suds)
appears in display
Load too large.
Load not balanced. The washer is
running a load-balance correction
routine.
Washer taking too long to fill.
Drain extends more than
4.5" (114 mm)into standpipe.
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm)into standpipe.
Hot and cold inlet hoses have been
installed incorrectly.
Excessive suds in washer. Washer is
running a suds reduction routine.
Hfan overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE
detergent. Close lid and press START/PAUSE.
Allow the machine to continue. Hfthe dial is flashing and the
machine has stopped, redistribute the load, close the lid, and
press START/PAUSE.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening. See "hstallation hstructions'.
Check plumbing for correct drain hose installation. Use drain
hose form and attach securely to drainpipe or tub. Do not tape
over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Instructions".
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions. If the
dial is flashing, reselect your desired cycle using a cold wash
temperature, and press START/PAUSE. Do not add detergent.
dL (Lid cannot lock) An item in the load may be keeping Check for items directly under the lid.
appears in display the lid from locking.
lid (Lid opened) Washer lid left open. Close the lid to clear the display. If the lid is left open for more
appears in display than 10 minutes, the cycle will reset and water in the washer
will drain.
dU (Lid cannot unlock) Objects on washer lid prevent it from Remove objects, such as a basket of laundry, from the top of
appears in display unlocking, the washer.
F## code (F-type System error code. Press START/PAUSE once to clear the code. Then press
error code) appears START/PAUSE again to restart washer. If code appears again,
in display call for service.
17

WHIRLPOOLCORPORATIONLAUNDRYWARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts
and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be
provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY
SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies
only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain
service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is
used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Whirlpool servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Whirlpool's published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or
cannot be easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the
problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling
Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 7/08
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
18

p p
$ECURXTE DE LA LA USE
Votre s_curit_ et celle des autres est tr_s importante,
Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.
Assurez=vous de toujours lire tousles messages de securit6 et de vous y conformer.
Voici le symbole d'alerte de s6curit&
Ce symbole d'alerte de securit6 vous signale les dangers potentiels de deces et de blessures graves
& vous et & d'autres.
Tousles messages de securit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de d_c_s ou de blessure grave si
vous ne suivez pas irnm6diaternent les instructions,
Risque possible de d_c_s ou de blessure grave
si vous ne suivez pas les instructions.
Tous les messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de
blessure et ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE SC:CURITI-
AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou de blessures Iors de I'utilisation de la
laveuse, suivre les precautions fondamentales dont les suivantes :
[] Lire toutes les instructionsavant d'utiliser la laveuse.
[] Ne pas laver des articles qui ont et6 nettoyes ou
laves avec de I'essence ou imbibes d'essence,
solvants de nettoyage &sec, ou autres substances
inflammables ou explosives; ces substances
peuvent emettre des vapeurs susceptibles de
s'enflammer ou d'exploser.
[] Ne pas ajouter d'essence, solvant de nettoyage &
sec ou autre produit inflammable ou explosif dans
I'eau de lavage. Ces substances peuvent 6mettre
des vapeurs susceptibles de s'enflammer ou
d'exploser.
[] Dans certaines conditions, de I'hydrogene gazeux
peut se former dans un circuit d'eau chaude qui n'a
pas 6t6 utilise pendant 2 semaines ou plus. LE GAZ
HYDROGI_NE EST EXPLOSIBLE. Si le circuit d'eau
chaude n'a pas et6 utilise pendant une telle periode,
avant d'utiliser la laveuse, ouvrir tousles robinets
d'eau chaude et laisser I'eau s'ecouler pendant
plusieurs minutes par chaque robinet. Ceci
permettra I'evacuation de I'hydrogene gazeux
accumule. Comme ce gaz est inflammable, ne pas
fumer ou utiliser une flamme nue au cours de cette
p6riode.
[] Ne pas laisser des enfants jouer sur ou & I'int6rieur de la
laveuse. Bien surveiller les enfants Iorsque la laveuse est
utilisee & proximit6 d'enfants.
[] Avant de mettre la laveuse au rebut ou hors de service,
enlever la porte ou le couvercle.
[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de
la laveuse Iorsque le tambour, la cuve ou I'agitateur est en
mouvement.
[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle
serait exposee aux intemperies.
[] Ne pas modifier les organes de commande.
[] Ne pas reparer ou remplacer un composant quelconque de
la laveuse, ni entreprendre une operation de service, si ce
n'est specifiquement recommande dans ce manuel ou dans
un manuel d'instructions de reparations destine & I'utilisateur;
il est alors essentiel que la personne concernee comprenne
ces instructions et soit competente pour les executer.
[] Pour les instructionsde liaison #,la terre, voir "Specifications
electriques" dans les instructions d'installation.
CONSERVEZ CES INSTRUCTIONS
Avertissements de la proposition 65 de I'Etat de Californie :
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour _tre & I'origine de
cancers.
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'Etat de Califomie pour 6tre & I'origine de
malformations et autres deficiences de naissance.
19

QUOI DE NEUF $OUS LE COUWERCLE?
Nettoyer avec moins d'eau
oo o| f"h
Laveuse traditionnelle
de type agitateur
Laveuse a faible consommation
d'eau avec impulseur
La nouveaut6 la plus flagrante de cette nouvelle laveuse est
son systeme de lavage a faible consommation d'eau avec
impulseur. La laveuse ajuste automatiquement le niveau d'eau
en fonction de la taille de la charge - nul besoin de s61ecteur
de niveau d'eau.
Lorsque I'on charge la laveuse de linge sale, celui-ci doit
6tre r6parti uniform6ment le long des parois du panier.
D6tection automatique de taille
de charge
Une fois que I'on d6marre le programme, le couvercle se
verrouille et la laveuse entame un processus de d6tection pour
d6terminer le niveau d'eau appropri6 a la charge. Cela peut
prendre plusieurs minutes avant que I'eau ne soit ajout6e. Voir
la description pas-a-pas dans la section "T6moins lumineux
de programme".
Vous entendrez le moteur faire tourner le panier par de brefs
mouvements d'impulsion pour bien imbiber la charge. Cette
m6thode de lavage avec faible consommation d'eau utilise moins
d'eau et d'6nergie qu'une laveuse traditionnelle de type agitateur.
_, mesure que la laveuse imbibe et d6place la charge, les
v_tements se tassent dans le panier. Ceci est normal et ne
signifie pas que I'on doive rajouter des v_tements.
IMPORTANT : Le panier de la laveuse ne sera pas rempli d'eau,
comme avec votre pr6c6dente laveuse de type agitateur.
Choix du d6tergent appropri6
Utiliser uniquement des d6tergents Haute efficacit6.
Uemballage portera la mention "HE" ou "High Efficiency"
(haute efficacit6). Un lavage avec faible consommation
d'eau produit un exces de mousse avec un d6tergent non HE
ordinaire. II est probable que I'utilisation d'un d6tergent ordinaire
prolongera la dur6e des programmes et r6duira la performance
de ringage. Ceci peut aussi entrainer des d6faillances des
composants et une moisissure perceptible. Les d6tergents HE
sont congus pour produire la quantit6 de mousse ad6quate
pour le meilleur rendement Suivre les recommandations
du fabricant pour d6terminer la quantit6 de d6tergent a utiliser.
Utiliser uniquement un detergent Haute efficacite (HE).
Nettoyage coneentr6
Le systeme de lavage a faible consommation d'eau signifie un
lavage concentr6. Plut6t que de diluer du d6tergent comme
dans une laveuse de type agitateur, cette laveuse libere le
d6tergent directement sur les endroits souill6s.
Sons normaux pr6visibles
Au cours des diffOrents stades du programme de lavage, vous
entendrez peut-_tre des bruits que votre laveuse pr6c6dente
ne produisait pas. Par exemple, vous entendrez peut-6tre
un cliquetis au d6but du programme Iorsque le systeme de
verrouillage du couvercle effectue un test automatique. On
entendra diff@ents bourdonnements et bruits de frottements
rythmiques a mesure que I'impulseur d6place la charge. Parfois,
il est possible que la laveuse soit completement silencieuse,
Iorsqu'elle d6termine le niveau d'eau ad6quat ou qu'elle laisse
tremper les v_tements.
2O