Whirlpool LASOOXK User manual

Model LASOOXK
Regular Capacity
Whirlpool AUTOMATIC WASHER
Use& Care
Guide
- LAUNDRY INFORMATION CENTER
-A / CYCLE CONTROL KNOB
h WATER TEMPERATURE
SELECTOR
-LOAD SIZE SELECTOR
[ Copy Your Model and Serial Numbers Here
I
When you need service, or call
with a question, have this Inform&on
ready. I,’ .i. _. r.-
1 Complete Model ar;d Serial Numbers
[from the plate under the lid near the ~~~~. ._~
hinge]. ,.-, ] ‘~ .:,e
2. Purchase date from sales sirp (or date
installed)
Copy ti-,ls InformatIon in these
spaces Keep this book in the Laundry
Information Center with your Loundry
Guide, sales slip and warranty

Before using
your Washer
Please read ihis booklet to be
sure your washer ISinstailed and used
properly It will help you get the best
results and longest life your washer wus
designed to gave
You are personally responsi-
ble for making sure that your
washer...
l Is Installed by a qualified installer
l Is properly installed and leveled on a
floor that can support the weight.’
l Is connected to the right kind of outlet,
electric supply, water supply and drain
l Is properly electrlcally grounded.
l Is used only for jobs normally
expected of home automatic washers
l Is properly maintained
l Is protected from the weather
l Is not run by children or anyone
unable to operate It properly.
Remove the Consumer Buy
Guide label It will be easier to remove
before the washer ISused
You may want to wipe out the
basket with a damp cloth before using
to remove dust from storing or shipping
SPECIAL INSTRUCTIONS: See the
laundry Guide for tips on deter-
gents, other laundry aids and
instructions for washing special
items.
See the lnstallatlon Instructions for
complete informatlon
I
1
CAUTION: Store laundry deter-
gent and additives in a cool, dry
place where children can’t
reach them.
Contents
Before Using Your Washer 2
Loading Your Washer 3
Understanding Your Washer 3
Using Your Washer 4
Water Levels and Load Sizes. 5
Important Detergent Information 6
Cleaning the Lint Filter 6
For a Pre-Wash 7
For Rinsing Only 7
For Spinning Only
CycleOperation L
PERMANENT PRESS 8
KNITS GENTLE
REGULARHEAVY ” 8 ” 8
SOAKCYCLE :‘. 10
If You Need Service or Help 10
1. Before Calling for Service 10
2. If You Need Service 11
3. IfYouHaveaProblem .,. 11

loading your
Washer ,c
For best washing results and
energy savings, sort the laundry
carefully.
1. Sort the Laundry into loads.
l Group the laundry into loads that
can be washed and dried together.
See the Laundry Guide for informa-
tion and samples of typical loads.
l Try to mix large and small items for
best movement in the washer.
2. Measure Detergent; Add to
Washer Basket.
l See detergent information on page
6 and in Section IV of the Laundry
Guide.
l Add dry bleach or water condi-
tioner (not fabric softener) if used.
Follow the package directions
carefully.
3. Dilute liquid Bleach Before Add-
ing to the Washer Basket.
l See the “Laundry Aids”section of
the Laundry Guide for more
information.
4. load the Washer.
l Spread the load evenly. (Don’t put
all the towels on one side and a few
wash cloths on the other.) An unbal-
anced load can cause the washer io
shake during spinning.
l Load without packing so items can
move freely for best cleaning and
least wrinkling.
5. Add Diluted Fabric Softener Only
to the Deep Rinse Cycle.
. DO NOT ADD FABRIC SOFTENER TO
THE WASH. Fabric softeners can com-
bine with soap or detergent to make
greasy stains on fabrics.
Understanding
your Washer
This automatic washer has cycle
settings with different agitation and spin
speeds for different fabric types For
example, the REGULAR HEAVY Cycle
has high agitation and high spin
speeds The PERMANENT PRESS Cycle,
has high agitation speeds, but low spin
speeds The washer has a
LOAD SIZE
SELECTOR that lets you adjust the water
level to match the size of the load.
It has a TEMPERATURE SELECTOR.
You can select the wash water temper-
ature best for the amount of so11and
fabric type In each load
Sections In this Use & Care Gude
go Into detail on the “what and why”
of each setting. Read this and the Laun~
dry Guide carefully to get the best
cleaning results

Your automatic uasher ISeasy to
use. To make it even easle’ read the
following steps before starting your first
ioad Start your washer after you put In
detergent, the load, and any other
laundry aids occordlng to InformatIon
on page 3
1. Set the LOAD SIZE SELECTOR.
l Select the water level that matches
the size of the load See page 5 for
more ~nformatior:
IMPORTANT For the best cleaning
sure the load has enough water for
2. Set the TEMPERATURE SELECTOR.
l Match the wash water temperature to
the type of fabrics and soils being
washed All rinses are cold
3. Select a Cycle and Start the
Washer.
l Push the Cycle Control Knob in and
turn It tothe right (clockwise)
l Stop when the pointer is on thenum~
ber of minutes of washing you want
in the cycle you want.
l Instructions for which cycles to use for
each fabric type are under the ltd.
l To start the washer, pull the Cycle
Control Knob out. When the cycle IS
over, the washer will stop.
l To stop the washer at any time
during a cycle, push the Control
Knob in. Pull It out to restart the washer
l To change a setting, push the Con-
trol Knob in to stop the washer. Then turn
the Control Knob to the right (clockwlse)
to the setting you want Pull the knob
out to start the washer
l Pages a- 11 show what happens In
each cycle

Water levels and
load Sizes
The LOAD SIZE SELECTOR lets You
control the amount of water that fills
the washer. The water level can be set
for extra small. medium or full loads.
WATER LEVELS
Setting Gallons/liters’
EX SMALL 9 9137.5
MEDIUM 13.5:51.1
LARGE 16 9,‘64.0
*Approximate fill with load
To save water and energy,
match the water level to the load
size.
For the best cleaning results, the
load should move freely in the water
Watch for rollover. An item [like a sock]
should sink in the middle and come
up later on the outsrde.
Be sure to read pages 11 13 In
your laundry Gu/de You will find more
rnformation on loading and load sizes

Important
Detergent
Information
Detergents and soaps clean
by looserxng soil, and by holding it In
the water so It drains away. If not
enough detergent ISused, so11and
lint can settle back on the items in
the load
SOAP works best in soft water
(O-4 grains hardness). In harder water.
both the wash and rinse water should
be softened. Use enough soap to
make about 1% to 2 Inches (3.8 to 5 5
cm) of suds.
DETERGENT works in hard or
soft water. Package directions are
usually based on soft water and
washers with normal-size tubs Use
more detergent...
1 for hard water.
2. for heavy greasy or
OIIV sotls
3. if the detergent is low
phosphate
4. for cold-water washes.
DETERGENT SUDS. There are
high, normal and low sudsing pow-
dered detergents If the recom-
mended amount of detergent makes
too much suds, switch to a lower
s&sing brand. DO NOT REDUCE THE
AMOUNT of detergent
Use the followlng chart as
begInnIng suggestlons for powdered
and liquid detergent amounts. See
your laundry Guide for more infor-
mation (pages 14-22).
WATER HARDNESS IN GRAINS
O-4 Grains 4-10 Grains lo-20 Grains
Powdered Detergents
Low Suds 34 cup (175 mL) 1’4 cups (250-300 1’4-1’/~ cups
ml1 [300-350 mL)
Normal Suds 1’4 cups (300 ml) 1% cups (425 mL) 2-2% cups
(475-525 ml]
High Suds l’J4-1”2 cups 2 cups (475 mL) 2'12cups (600 ml]
(300-350 mL)
No phosphate -Follow package recommendations -
Liquid Detergents I4 to 1cup (60 to 250 ml), depending on the brand and
amount of soil. Follow package recommendations.
*These recommendations do not apply...
l In areas where phosphates are banned.
l In areas with laws limiting (by weight or percentage) the amount
of detergent used in a wash load.
Cleaning the lint
Filter
Water runs through the lint filter
whenever the washer agltotes Check It
often to make sure It’s clean and filter-
ing at Its best
To remove it for cleaning, press
the release and pull strolght oui lnstruc-
tlons for cleaning are prlnted on the
bottom of the filter
6

For a Pre Wash
Use this settrnli for a sh#orter SOAK
CYCLE (no rinse] Use enough1 detergent
for a single wash. Add the load.
l Set the LOAD SIZE SELECTOR.
l Set wash water temperature
tf you want high agitation and a
high-speed sprn. use the dot In REGU-
LAR HEAVY. If you want low agrtation
and a low-speed spin, use the dot In
KNITS GENTLE Use the dot in PERMA-
NENT PRESS If you want high agrtation
and a low-speed spin.
For Spinning Only
l Push the Cycle Control Knob in and
turn It to the 12.minute mark rn the SOAK
CYCLE
l Pull the Control Kr ob out tc start the
washer
l The washer will fill agitate for two
minutes, soak for eight minutes, agitate
for two more, and then drain and spin
l After filling, the washer may pause
before starting to agitate.
For Rinsing Only
Loads with towels, diapers, jeans
or heavily sorled Items often need extra
detergent Extradetergentcanrequire
an extra rinse
Your washer can be set to rinse
only. Use the setting for an extra rinse, or
for laundry that only needs a rinse and
There may be times when you
want to drain out all the wash water and
start over. To stop the washer at any
time, just push In on the Cycle Control
Knob.
To set the washer so it drains and
spins water out of the load, push in on
the Control Knob, turn the dial to the
right (clockwrse) so the pointer is touch-
ing the bar just before OFF in any cycle.
The washer will drain, spin out
water and stop. If you want a low-speed
spin, use the bar on PERMANENT PRESS
or KNITS GENTLE. All the other cycle
settrngs have a high-speed spin
There IS o dot just after the num-
bers in PERMANENT PRESS, REGULAR
HEAVY and KNITS GENTLE If you push in
on the Cycle Control Knob, turn the
pointer to one of those dots and pull the
Control Knob out. the washer will fill,
agitate, drain and spin.

Cycle Operation
The numbers tn each cycle are
for the number of minutes YOU want the
Your washer has four cvcles on washer to agitate before it drains and
the Cycle Control Dial Eacti cycle IS fills for the rinse. You will want longer
designed to match the fabr’c type with agttation times for heavrly soiled loads
pre-set agitatron and spin speeds You choose the wash water tem-
WHAT HAPPENS IN EACH CYCLE:
I
CYCLE AND TME I uI(
l PULt OUT TO START
1
PARTIAL
DRAIN
Pause
KNITS GENTLE CYCLE
Use for delicate items and washable
synthetic knits such as polyester, nylon,
acrylrc Wash nylon hose or panty hose
in a net laundry bag
* SET LOAD SIZE
* SET WATER TEMPERATURE
. PUSH IN KM%, TURN TO
CYCLE AND IIME
* PULL OUT TO START

perature you want with the NOTE: You may notice that some
TEMPERATURE SELECTOR. Rinse water is of the “SPIN”cycles have
SPRAY RIN-
cold in all settings.
SES. Cold water is sprayed on the
You set the amount of water that spinning load to help rinse and remove
fills the tub with the LOAD SIZE
detergent residue.
SELECTOR.
LOW
SPEED
1 SPtN
L
4 Spw
Rinses
if you turn to u cycle ond start the
washer, but change your m/nd, push In
on the Cycle Control Knob and turn
to the right (clockwise) to the setting you
wont. Then DU// out to start.
WASH
‘El
The washer pauses for about 1”~
Hk$-b
minutes after partial drain
Agit&im
LOW
SPEED
0
SPIN

If You Need
Service or Help,
We suggest You
Follow These Three
Steps:
1. Before calling for service.
Problems -Ire somdtlmes causer:
by lrttle things you car) correct wlihou:
tools Check thus list before you call
for servrce
IF YOUR WASHER DOES NOT FILL:
l Is the power supply cord plugged In?
l Are both water faucets open?
l Is a fuse blown or circuit-breaker
tripped’,
l Are the water supply hoses kinked?
l Is the Cycle Control Knob set and
pulled out?
IF YOUR WASHER DOES NOT SPIN:
l Is the lid closed7
l Is the power supply cord plugged In?
l Is a fuse blown or circuit-breaker
tripped?
IF WASHER FILLS AND DRAINS WITHOUT
RUNNING:
l Make sure that the Cycle Control
Knob ISpointing to a number in the
cycle.
IF YOUR WASHER STOPS DURING THE
PERMANENT PRESS CYCLE.
0 Remember, the washer will stop for
about 1% minutes after the partial drain
during the cool-down period in this
cycle
MAKE SURE THE DRAIN HOSE IS HIGHER
THAN THE WATER LEVEL IN THE WASHER.
IF IT ISN’T...
l The washer may seem to be draining
during wash and rinse cycles.
l Water can siphon out [See Installation
Instructions,)

Before adding detergent for washing dissolve in quart of warm water [or
use llquld detergent)
Ir- Pre Wash setting (page 7) beglns here
2. If you need service’ :
If your WHIRLPOOL appliance ever
needs service anytihere I? the United
States, help ISJust a phone call away
to your nearest Whirlpool franchised
TECH-CARE ’ service representative
WhIrlpool molntalns a nationwide
network of franchised TECH-CARE ser-
vice companies to fulfill vour warranty
and provide after-warranty service and
maintenance to keep your WHIRLPOOL
appliance In peak condition
You’ll find your nearest TECH-CARE
service company llsted in your local
telephone book Yeilow Pages under
APPLIANCES - HOUSEHOLD ~ MAJOR
SERVICE & REPAIR Should you not find
a listing, dial free, the Whirlpool
COOL-LINE” service assistance tele-
phone number.
When calling from:
Michigan [phone]
Alaska &
Hawaii (800) 253-l 121
All other
states (800) 253-l 301
If you move...To make sure that your
appliance is correctly installed and to
insure Its contrnued satisfactory
operation, please telephone your
nearest TECH-CARE - service cornpanv
for +nstallat+on or to get the name of a
qualified installer (Installation cost will,
of course, be paId by you.)
Helpful hinfs...You can help your
TECH-CARE service representative give
you faster service If you include the
model and serial number of your
appliance when requesting servrce
Also, retain your sales slip and warranty
to verify your warranty status
Remember...Your TECH-CARE service
representative ISspecially trained In the
expert repairing and servrclng of your
WHIRLPOOL applrances He can help
you maintain the quality ortglnally built
into your WHIRLPOOL appliance So why
not take the time, now, to look up his
telephone number and jot it down In the
space provided on the cover
3. If you have a problem’ :
Call WhIrlpool Corporation in Benton
Harbor at the COOL-LINE service
assistance telephone number [see Step
2) or write:
Mr Guy Turner, Vice President
WhIrlpool Corporation
Admrnlstratlve Center
2000 US 33 North
Benton Harbor, Michigan 49022
’ If you must call or write, please
provide your name, address,
telephone number, type of appliance,
brand, model, serial number, date of
purcnase, the dealer’s name, and a
complete description of the problem.
This information is needed In order to
better respond to your request for
assistance

FSP 1sa regIstered trademark
0
of Whirlpool Corporation for
quality parts Look for thrs
FSP symbol of quollty
whenever
you need a replacement part
s? for your Whrlpool appliance
FSP replacement ports
~111fit right and work right because they are
made to the same exacting spec~flcotlons
used to build every new Whlrlpml oppllance
TLrlpool
Benlon Harbor. Michigan. Aulomallc Washers, Clolhes Dryers.
Freezers. Relrigeralor-Freezers, Ice Makers. Dishwashers.
Buill-in Ovens and Surlace Unils, Ranges. Microwave Owns,
Lompaclors. tloom Air Condilioners. Dehumiditters, Central
Home Appliances Healing and Au Condilianrng Syslems.
Quality. Our way of life
Part No 382592 Rev. A Printed In U.S A