Whirlpool WFS1274AW User manual

WFS1274AW
A. Onloff button
B. Water tap closed indication
C. Clean pump indication
D. Reset/Drain button
E. Programme selector
F. Favorite button
Type of wash/Notes
Care
Programme . ;
Labels |-for temperature selection, please follow the manufacturer's recommendation on
the care label
Peres Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc.
*(cold),30,40 \&7 \6W |made of cotton and linen.
60.95°C X67 (407 |With heavily soiled laundry the additional "prewash" option can be selected as well.
, Maximum load for 20°C and 30°C programs:5.5kg.
Synthetics
*(cold),30 , 40°C
Daily Wash
*(cold),30,40,60°C
Slightly to normally soiled textiles made of cotton and/ or synthetics.
Quick Wash
*(cold),30°C
Only woollens with a felt-free finish, labelled with the Woolmark and identified as
machine washable.
If you select "Rinse Hold" do not leave items to soak for too long.
Wool
*(cold),30,40°C
Textiles made of linen, silk,wool and viscose marked as"handwashable".
ane If you select "Rinse Hold" do not leave items to soak for too long. A very gentle
(cold), 30’c spin is used in this programme.
Rinse & Spin | — | Same as the last rinse and the final spin in the "Cotton" programme.
In this programme spinning is intensive. Same as the spin cycle in the "Cotton"
programme.
Gentle Spin | = In this programme spinning is gentle. Same as the spin cycle in the "Wool"
programme.
“optional Yes: dosing required —: can not be selected
(1)
(2)
For improved garment care, spin speed is restricted to 1000 rpm in this program.
For improved garment care, spin speed is restricted to 400 rpm in this program.
PROGRAMME CHART
ay way [Normal soiled blouses, shirts, overalls etc. made of polyester(Diolen, Trevira),
ay wa [Normal (Perlon, Nylon) or blends with cotton.
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with
Ww cotton.
G. Start/pause button
H. Service indication
|. Door open indication
J. Special options buttons
K. Display window
L. Temperature, Start delay , Spin speed buttons
Detergent and additives Special options
Favorite
Prewash |Main wash|Softener Start Easy |Intensive]Rinse] spin
\Il] \B] delay bd ironing] rinse | hold | speed
i lela]
Ban
pee
| |
BE
rin SSC ee
Fe te Ee Ea BEES
Whirlpool is a registered trademark of Whirlpool USA
BASIC CHART
Max.
Spin
speed
*
* *
* * *
*
* *
*
refer pe fetes fer

PROGRAMME DATA
cold, 30
Synthetics a
Synthetics | cold,30 Ci
cold,30
Quick wash cold,30
cold,30
pC
YOK el
[3 —..60:_— =]
cotton XOX er: al
| cold,30_
Temperature
40
| Dailywash_—-|_—S60—s
| Dailywash__ | __ cold, 30,40
| Quick wash
a 7 ae
Et 7 a
as
26
a
Ee
a
a
a
a
Approx. Programme
7
7
7
2
2
3
3
3
a
a
cold,30 pO
Hand Wash cold,30 EE nn ea a
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
x The remaining time indicator can deviate from the values in the table, because it takes into account the house conditions applicable at that time.
343% To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out
3% 38t3% Reference Programme for Energy Label, AS/NZ 2040.1:2005.
ADD DETERGENTS, CLOSE THE DOOR
AND ADD SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives" in
your instruction for use.
1. Push the On/off button,the light below the
Start/Pause button is bright, the display window
shows the status of default program(cotton 40°C).
2. Push the programme selector to the desired
programme. Then push the Temperature, Start Delay,
Spin Speed button to change the program if neces-
sary.
3. Push the Start/Pause button at least 3 seconds to
start the programme.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired the respec-
tive indiction lights up. When the combination of the
programme and additional option(s) is not possible,
the indication lights switch off automatically. Unsuitable
combinations of options are deselected automatically.
" Prewash" button
* Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
“ Intensive rinse" button
* An extra rinse is added and rinse cycle prolonged.
* This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
"Eco " button
* With a modified temperature profile and a slightly
prolonged washing duration, the optimum combination
of excellent washing result and even lower energy
consumption is achieved, if temperature selected is
R:)
5
5
5
5
0
0
0
1.5
1.0
1.0
1.0
above 50°C.
"Easy ironing" button
* Can be used together with cotton or synthetics
programme to make ironing easier.
* Increases the water quantity and the clothes are
spun very gently.
" Rinse hold" button
*The laundry remains in the last rinse water without
processing to the final spin cycle to avoid creasing .
*This option is particularly recommended for the
programme “Synthetics”, "Everyday wash" and "Hand
wash".
*lt is particularly useful if you want to postpone spin-
ning to a later time, or if you want to drain only.
Notes: The programme stops to "Rinse hold" at the
time the "Rinse hold" light in the programme
sequence indication is on. The indication lamp next
sequence the "Start/Pause" button flashes.
Terminate the “Rinse hold" option
*Press the "Start/Pause" button; the programme will
terminate automatically with the final spin cycle for the
preset wash programme.
*lf you do not wish to spin the clothes, press the
"Reset/Drain" button and then press the
"Start/Pause" button.
SYMBOLS IN THE DISPLAY WINDOW
When the programme is running, some symbols light
up in the display window.
(From up to down, left to right)
The first column: (temperature indication) 95, 60, 40,
30, *(cold) .
lf the washer is in “operation” ,the second column
means: prewash, main wash, rinse, hold rinse,
spin/drain.
If the washer is in “Start Delay” , the second column
means 24,12,6,3,1 hours.
The third column: (spin speed indication) 1200, 1000,
800, 400, 0 rpm.
TEMPERATURE, START DELAY AND SPIN
SPEED
Temperature, Spin speed adjustment
When you select a programme, the default tempera-
ture and spin speed shows in the screen. Press "Tem-
perature", "Spin Speed" button to adjust if you want.
Start Delay
The "Start Delay" allows to run the machine at the
consumer's convenience, for example, at night when
the electricity might be cheaper.
*Select the programme , temperature and options.
«Press the "Start Delay" button to select the delay
time by 1, 3, 6, 12, 24 hours.
«Press the "Start/Pause" button. The countdown of
the delay time begins. It shows in the screen.
*Once having pressed the "Start/Pause" button, the
remaining time preselected can be adjusted by press-
ing again the "Start Delay" button.
To cancel the "Start Delay"
*Before you press the "Start/Pause" button
Press other programme selector or press the
"Reset/Drain" button
«After you press the "Start/Pause" button
Press the "Reset/Drain" button for at least 3 seconds,
the start delay time disappears from the screen.
PROGRAMME START
Open the tap and press the "Start/Pause” button, the
indication lamp next to the button lights up. Some
symbols of programme light up in the display window
to show the condition of the machine.
“DOOR OPEN" INDICATION
Before start and after end of a programme, the blue
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked, and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to " Cancel (Reset)
a running programme before the end".
RED INDICATIONS
"Water tap closed"
The appliance has no or insufficient water supply,
open the water tap; if the indication still light up, refer
e
—
0.
to the "Troubleshooting Guide" in the instruction for
use.
"Clean pump"
Waste water can not be pumped out. Check whether
the drain hose is kinked or the filter must be cleaned;
in the latter case refer to the Instruction for use
("Removing the filter").
"Service"
The appliance stops during the programme. If the
service indication lights up and the start delay LED bar
appears on the display, please contact After-Sales
Service(see "After-Sales Service").
FAVORITE PROGRAMME
When you have done the programme setting and do
not press the "Start/Pause" button, press the "Favor-
ite" button at least 3 seconds to set the programme as
your favorite programme. You can set a favorite
setting for every main wash programme. But if you
want to set another favorite setting for the programme,
the former setting will be covered.
PROGRAMME END
All the lights of the programme sequence indicator are
off in the display window, and the door open indication
lights up.
1.Press the "On/Off" button to disconnect the electric-
ity, close the water tap.
2.Open the door and unload the machine.
3.Leave the door open to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light around the button flashes.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent if already added on original selection. If you
want to adjust the programme when the machine is
running, press “Reset/Drain” button at least 3 sec-
onds, then choose other programme setting button.
CANCEL (RESET) A RUNNING PRO-
GRAMME BEFORE THE END
*Before you select a programme, press the
"Reset/Drain" button, then press "Start/Pause" button
to drain if you want.
«When a programme is running, press the
"Reset/Drain" at least 3 seconds to reset all the
settings and drain. Push the programme selector to
select other programmes.
Whirlpool is a registered trademark of Whirlpool USA
4619 704 82331

INSTALLATION GUIDE
NOISE, EXCESSIVE VIBRATIONS AND WATER LEAKAGES
CAN BE CAUSED BY INCORRECT INSTALLATION.
NEVER MOVE THE APPLIANCE BY CARRYING IT AT THE
WORKTOP.
Read this “INSTALLATION GUIDE” before operating.
Keep this “INSTALLATION GUIDE” for future reference.
Read the general recommendations about disposing of packaging in the
INSTRUCTION FOR USE.

PARTS SUPPLIED
« Package with small items
Instruction for use, installation guide, warranty card
(depends on model)
4 plastic caps
Wrench(depends on model)
Inlet
hase
(inside
the
machine
or
already
installed)
Cold
inlet
hose
Hot
inlet
hose
(if
available,
depending
on
models)
“U"-bend
(inside
the
machine
or
already
installed)
€)

BEFORE
USING
THE
WASHER,PLEASE
REMOVE
TRANSPORT
BOITS!
A WARNING
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury
Note:
To
avoid
floor
damage,
set
the
washer
onto
cardboard
before
moving
across
floor
Important: Not removed transport bolts cause damages to the appliance.
Unscrew the four screws (see arrows) with the wrench C supplied.
@)
@)

To
seal
the
holes
insert
the
supplied
plastic
caps
B
in
the
wide
part
of
the
hole
and
slide
them
in
the
direction
of
the
arrow
until
they
click
into
place.
Important:
Keep
the
transport
bolts
and
the
wrench
for
further
transporting
of
the
appliance
and
in this case
refit
the transport
bolts
in
reverse
order.
ADJUSTMENT OF THE FEET
The
appliance
must
be
installed
on
a
solid
and
level
floor
surface
(if
necessary
use
a
spirit
level).
lf
the
appliance
is
to
be
installed
on
a
wooden
floor,
distribute
the weight by placing it on a 60x60 cm sheet of plywood at least 3 cm in thick-
ness
and
secure
it
to
the
floor.
If
the
floor
is
uneven,
adjust
the
4
leveling
feet
as required; do not insert pieces of wood etc. under the feet.
©)
Slacken
the
locknut
clockwise
(see
arrow)
using
the
wrench
C
supplied.
Lift
slightly
the
machine
and
adjust
the
height
of
the
foot
revolving
it.
ip)
» 28
y
n_7
ee Lower

@
important:
tighten
the
locknut
by
turning
it
anti-clockwise
towards
the
appliance casing.
NEE IRE
CONNECT THE WATER SUPPLY INLET HOSE
If
the
water
inlet
hose
is
not
already
installed
,it
must
be
screwed
to
the
appliance.
The
blue
marked
hose
is
only
for
cold
water
.
Depending
on
different
models,
hot
water
hose
marked
with
red should
also
be
connected.
Hot Cold
(Depending on models)
(9)
Screw
by
hand
the
inlet
hose
onto
the
tap
tightening
the
nut
Attention:
e
no
kinks
in
the
hose!
e
The
appliance
must
not
be
connected
to
the
mixing
tap
of
an
un-pressurized
water
heater.
e
Check
water-tightness
of
connections
by
turning
the
tap
completely
on.
e
Ifthe
hose
is
too
short,
replace
it
with
a
suitable
length
of
pressure
resistant
hose
(1000
kPa
min,
EN
50084
approved
type).
e
Check
the
inlet
hose
regularly
for
brittleness
and
cracks
and
replace
if
necessary.
e
The
washing
machine
can
be
connected
without
a
non-return
valve.

For models with Water Stop hose:
If
the
flexible
hose
is
too
short,
replace
it
with
a
3
m
Water
Stop
hose
(available
for
sale
from
After-Sales
Service
or
from
your
dealer).
This
replacement
is
only
to
be
carried
out
by
a
trained
electrician.
Depending
on
the
model,
the
inlet
hose
and
the
plastic
enclosure
at
the
tap
connection
contain
electrical
components.
Do
not
cut
the
hose
and
do
not
immerse
the
plastic
enclosure
in
water.
Isolate
the
appliance
from
the
mains immediately if the hose is damaged.
HOT / COLD FILL INSTRUCTION
10
40)
If
you
wish
to
connect
hot
and
cold
water
supply
(Fig.1):
1.
Fix
the
red
marked
inlet
hose
at
the
hot
water
tap
and
at
the
inlet
valve
with
the
red
filter
on
the
rear
side
of
machine.
2.
Fix
the
other
inlet
hose
at
the
cold
water
tap
and
at
the
inlet
valve
with
the
blue
filter
on the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b)
Do
not
invert
their
position
(for
example:
cold
fill
into
hot
inlet
valve
and
viceversa).
If
you
wish
to
connect
only
the
cold
fill
follow
the
below
instruction
(Fig.2):
1.
You
need
a
Y-piece
connector.
This
can
be
purchased
from
local
hardware
or
plumb-
ing
supplier.
2. Fix the Y-piece connector to the cold fill tap.
3.
Connect
the
two
inlet
valves
present
on
the
rear
part
of
the
machine
to
the
Y-piece
connector
using
the
relative
provided
hoses.
Make sure:
All connections are tightly fixed,

Do
not
allow
children
to
operate,
crawl
on,
near
or
inside
your
washer.
Note
that
during
wash
cycles,
the
surface
temperature
of
the
porthole
door
may
increase.
Close
supervision
of
children
is
necessary
when
the
appliance
is
used
near
children.
Hot
fill
w_
Cold
fill
Blue inlet valve |
Cold fil
~~ _Y-piece

CONNECT THE DRAIN HOSE
In
case
the
drain
hose
is
installed
as
shown
below:
Unhook
it
only
from
the
right
clip
(see
arrow)
(2)
Connect
the
drain
hose
to
the
siphon
or
hook
it
over
the
edge
of
a
sink
by
means
of
the
"U"
bend.
Fit
the
“U”
bend
E,
if
not
already
installed,
at
the
end
of
the
drain
hose.
Notes:
Make sure there are no kinks in the drain hose
Secure
the
hose
so
that
it
cannot
fall
down.
After
wash
phase,
machine
will
drain
out
hot
water.
Small hand basins are not suitable
To
make
an
extension
use
a
hose
of
the
same
type
and
secure
the
connections
with
clips.
Max. Overall drain hose length: 2.50 m.