White Rodgers 1F80-51 User manual

Topreventelectricalshockand/orequipmentdamage,
disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.
Do not use on circuits exceeding specified voltage.
Higher voltage will damage control and could cause
shock or fire hazard.
Do not short out terminals on gas valve or primary
control to test. Short or incorrect wiring will damage
thermostat and could cause personal injury and/or
property damage.
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE
PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION
YournewWhite-Rodgers5-Day/2-DayDigitalThermostatuses
the technology of a solid-state microcomputer to provide pre-
cise time/temperature control. This thermostat offers you the
flexibility to design heating and cooling programs that fit your
needs.
Features:
• Battery powered (3 “AA” Energizer® alkaline batteries in-
cluded).
• Separate5-day(weekday)and2-day(weekend)programming
• Simultaneous heat and cool program storage
• Preprogrammed temperature control
• Fourseparatetime/temperaturesettingsper24-hourperiod
• LCD continuously displays set point, and alternately dis-
plays time and room temperature
• Temperature override until next program period
• Manual program override (HOLD temperature)
• User may select either 12- or 24-hour clock display
•°F/°C convertibility
• Temperature range 45°to 90°F
• Standard five terminals for single or two-transformer sys-
tems
• B and O terminals for single stage heat pumps or damper
operation
SPECIFICATIONS
ELECTRICAL DATA
Electrical Rating:
8 to 30 VAC 50/60 Hz. or D.C.
0.05 to 1.5 Amps (Load per terminal)
1.5 Amps Maximum Total Load (All terminals combined)
THERMAL DATA
Setpoint Temperature Range:
45°F to 90°F (7°C to 32°C)
Operating Ambient Temperature Range:
32°F to 105°F
Operating Humidity Range:
0 to 90% RH (non-condensing)
Shipping Temperature Range:
-40°F to 150°F
APPLICATIONS
For use with:
• Standard heat/cool or heat only systems
• Electric heat systems
• Gas or oil fired systems
• Gas systems with intermittent ignition devices (I.I.D.)
and/or vent dampers
• Hydronic (hot water or steam) systems
• Single-stage heat pump systems
• Millivolt systems
DO NOT USE WITH:
• Multi-stage systems
• Systems exceeding 30 VAC and 1.5 amps
• 3-wire zoned hydronic heating systems
1F80-51
Programmable Electronic Digital Thermostat
Printed in U.S.A. PART NO. 37-5285E
Replaces 37-5285D
0004
WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS ROAD
ST. LOUIS, MISSOURI 63123-5398
WHITE-RODGERS INSTALLATION AND
OPERATION INSTRUCTIONS
PRECAUTIONS
CAUTION
!
This thermostat is intended for use with a low voltage system;
donotusethis thermostat withalinevoltage system. Ifindoubt
about whether your wiring is millivolt, line, or low voltage, have
it inspected by a qualified heating and air conditioning contrac-
tor or electrician.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical codes
and ordinances.
This control is a precision instrument, and should be handled
carefully.Roughhandlingordistortingcomponentscouldcause
the control to malfunction.
WARNING
!
Operator: Save these instructions for future use!

2
INSTALLATION
REMOVE OLD THERMOSTAT
1. Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
2. Remove the front cover of the old thermostat. With wires
still attached, remove wall plate from the wall. If the old
thermostathasawallmountingplate,removethethermostat
and the wall mounting plate as an assembly.
3. Identifyeachwireattachedtotheoldthermostatusingthe
labels enclosed with the new thermostat.
4. Disconnect the wires from old thermostat one at a time. DO
NOT LET WIRES FALL BACK INTO THE WALL.
5. Install new thermostat using the following procedures.
ELECTRIC HEAT OR SINGLE-STAGE
HEAT PUMP SYSTEMS
Readentireparagraphbeforesetting electric heat switch.Ifyou
areunsureofyourapplication,contactaqualifiedserviceperson.
If you have a single-stage heat pump system, OR your system
uses central electric heat, where the blower is energized by a
separate circuit through the fan relay (meaning that the fan
turns on immediately on call for heat), then the switch on the
backofthe thermostat basemustbemoved to the“ELECTRIC”
position (see fig 1). If the thermostat is energizing electric heat
sequencers, the switch MUST remain in the “GAS” position.
If you must move the switch to the “ELECTRIC” position (to the
left), use a small screwdriver or pencil.
ATTACH THERMOSTAT BASE TO WALL
1. Remove the packing material from the thermostat. Gently
pull the cover straight off the base. Forcing or prying on the
thermostatwillcausedamagetotheunit.Ifnecessary,move
the electric heat switch (see ELECTRIC HEAT SYSTEMS,
above).
2. Connect wires beneath terminal screws on base using
appropriate wiring schematic (see figs. 3 through 10).
3. Place base over hole in wall and mark mounting hole
locations on wall using base as a template.
4. Move base out of the way. Drill mounting holes.
5. Fasten base loosely to wall, as shown in fig. 2, using two
mounting screws. Place a level against bottom of base,
adjust until level, and then tighten screws. (Leveling is for
appearance only and will not affect thermostat operation.) If
you are using existing mounting holes, or if holes drilled are
too large and do not allow you to tighten base snugly, use
plastic screw anchors to secure subbase.
6. Pushexcesswire into wallandplughole with afire-resistant
material(suchasfiberglassinsulation)topreventdraftsfrom
affecting thermostat operation.
BATTERY LOCATION
This thermostat requires 3 “AA” alkaline batteries to operate.
Batteries are installed in the thermostat at the factory with a
battery tag to prevent power drainage. You must remove the
batterytagtoengagethebatteriesandprovidepowertothe
thermostat.
If the word BATTERY is displayed, the batteries are low and
shouldbereplacedwithfresh“AA”Energizer®alkalinebatteries.
Toreplacethebatteries,install the batteries alongthetopofthe
base (see fig. 2). The batteries must be installed with the
positive (+) ends to the left.
HYDRONIC (HOT WATER OR STEAM)
HEATING SYSTEMS
This thermostat is set to operate properly if you have a forced-
air heating system. If you have a hydronic heating system (a
system that heats with hot water or steam), you must set the
thermostat to operate properly with your system. While in the
HEAT mode, change the setting by pressing and holding SET
TIMEandVIEWPRGMbuttonsatthesametimeuntilthecorrect
setting is displayed (Afor forced air; Hfor hydronic systems). If
there is a loss of battery power, or when you change batteries,
you must repeat this operation once battery power is restored.
Ifyou do notpress both buttonsat thesame time, AorHwill not
bedisplayed.Ifthishappens,pressRUNPRGM,thenpressand
hold SET TIME and VIEW PRGM at the same time.
NOTE
ELECTRIC GAS
Figure 1. Back of thermostat base
Electric/Gas switch
Figure 2. Thermostat base
Mounting
holes
Screw anchors
Alkaline batteries (3 "AA"–
install "+" ends to the left)
W
RH
B
Y
O
G
RC

3
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 8. Typical wiring diagram for
heat/cool, 5-wire, two-transformer systems
HEATING TRANSFORMER
Heating
System
Fan
Relay
Cooling
System
RC
24 VAC 120 VAC
Hot
Neutral
COOLING TRANSFORMER
OB
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 7. Typical wiring diagram for
heat/cool, 4-wire, single transformer systems
TRANSFORMER
Heating
System
Fan
Relay
Cooling
System
RC
JUMPER
WIRE
RED jumper wire (provided
with thermostat) must be
connected between thermo-
stat's RH and RC terminals
for proper thermostat oper-
ation with this system.
NOTE
OB
RW B
W
R
Thermostat 3-wire Series 10
Primary Control
(located at furnace)
Add jumper wire
(not provided with thermostat)
Figure 4. Typical wiring diagram for
3-wire SERIES 10 heating systems
Furnace
Jumper wire must be
added between Rand B
terminals on the primary
control (jumper wire not
provided with thermostat).
NOTE
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 5. Typical wiring diagram for
heat only, 3-wire, single transformer systems
TRANSFORMER
Heating
System
Fan
Relay
YRC
JUMPER
WIRE
RED jumper wire (provided
with thermostat) must be
connected between thermo-
stat's RH and RC terminals
for proper thermostat oper-
ation with this system.
NOTE
OB
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 10. Typical wiring diagram for
heat pump with heat active reversing valve
TRANSFORMER
Reversing
Valve*
RCOB
JUMPER
WIRE
Compressor
Contactor
JUMPER
WIRE
* Reversing valve is energized when the
system switch is in the HEAT position
Fan
Relay
RH
Y
THERMOSTAT
SYSTEM
G W
Figure 3. Typical wiring diagram for heating only,
2-wire, single transformer systems or millivolt systems
Heating
System
RCOB
24 VAC Transformer
or
Thermopile
RH
Y
24 VAC 120 VAC
Hot
Neutral
TRANSFORMER
THERMOSTAT
SYSTEM
G W
Figure 6. Typical wiring diagram for
cool only, 3-wire, single transformer systems
Cooling
System Fan Relay
RCOB
RH
Y
24 VAC 120 VAC
Hot
Neutral
THERMOSTAT
SYSTEM
G W
Figure 9. Typical wiring diagram for
heat pump with cool active reversing valve
TRANSFORMER
Reversing
Valve*
RCOB
JUMPER
WIRE
Compressor
Contactor
JUMPER
WIRE
* Reversing valve is energized when the
system switch is in the COOL position
Fan
Relay
CHECK THERMOSTAT OPERATION
If at any time during testing your system does not operate
properly, contact a qualified serviceperson.
Fan Operation
If your system does not have a Gterminal connection, skip to
Heating System.
1. Turn on power to the system.
2. Move fan switch to ON position. The blower should begin to
operate.
3. Move fan switch to AUTO position. The blower should stop
immediately.
Heating System
1. Move SYSTEM switch to HEAT position. If the heating
system has a standing pilot, be sure to light it.
2. Press toadjust thermostatsetting aboveroom tempera-
ture. The heating system should begin to operate.
3. Press toadjusttemperaturesettingbelowroomtempera-
ture. The heating system should stop operating.

4
Cooling System
This thermostat has a built-in short-term (5-minute) time delay.
This feature is activated after the compressor shuts down and
the setpoint is changed within the 5-minute period. During this
5-minute period, COOL will flash on the display indicating that
the thermostat has locked out the compressor to allow head
pressuretostabilize.Thisthermostat does not senseACpower
loss and therefore does not activate the short term compressor
protection feature when power is restored.
Topreventcompressorand/orpropertydamage,ifthe
outdoor temperature is below 50°F, DO NOT operate
the cooling system.
1. Move SYSTEM switch to COOL position.
2. Press toadjustthermostatsetting below room tempera-
ture.Theblowershouldcomeonimmediatelyonhighspeed,
followed by cold air circulation
3. Press to adjust temperature setting above room tem-
perature. The cooling system should stop operating.
CAUTION
!
Before you begin programming your thermostat, you should be
familiarwithitsfeaturesandwiththedisplayandthelocationand
operationofthethermostatbuttons.Yourthermostatconsistsof
two parts: the thermostat cover and the base. To remove the
cover, gently pull it straight out from the base. To replace the
cover, line up the cover with the base and press gently until the
cover snaps onto the base.
THE THERMOSTAT BASE
Other than and , the following buttons and switches are
located behind the door on the bottom of the thermostat cover
(see fig. 11). Pull the door down to open it.
The Thermostat Buttons and Switches
1
(Red arrow) Raises temperature setting.
2
(Blue arrow) Lowers temperature setting.
3
SET TIME button.
4
VIEW PRGM (program) button.
5
RUN PRGM (program) button.
6
HOLD TEMPerature button.
7
FAN switch (ON, AUTO).
8
SYSTEM switch (COOL, OFF, HEAT).
The Display
9
Indicates day of the week.
10
HEATisdisplayedwhentheSYSTEMswitchisintheHEAT
position. COOL is displayed (non-flashing) when the SYS-
TEM switch is in the COOL position. COOL is displayed
(flashing) when the compressor is in lockout mode.
11
Alternately displays current time and temperature.
12
BATTERY is displayed when the 3 “AA” batteries are low
and should be replaced. Nothing else will be displayed.
13
Displays currently programmed set temperature (this is
blank when SYSTEM switch is in the OFF position).
14
The word HOLD is displayed when the thermostat is in the
HOLD mode.
OPERATION
Figure 11. Thermostat display, buttons, and switches
3
2
1
4 5 6 7 8
AUTOSET TIME VIEW PRGM RUN PRGM HOLD TEMP FAN ON COOL OFF HEAT
SU
HOLD
SA
COOL
BATTERY
AM
MO TU WE TH FR HEAT
9 910
1012 1113 14
11

5
WEEKDAY (5 DAY) WEEKEND (2 DAY)
Start
Time* Temperature Start Time* Temperature
1ST HEAT
2ND HEAT
3RD HEAT
4TH HEAT
1ST COOL
2ND COOL
3RD COOL
4TH COOL
SAMPLE
Heating/Cooling Schedule Plan
Period
5:30 AM
8:00 AM
5:00 PM
10:30 PM
6:30 AM
2:00 PM
5:00 PM
10:30 PM
7:00 AM
11:00 AM
6:00 PM
11:30 PM
7:00 AM
12:30 PM
6:00 PM
11:30 PM
68°F
70°F
70°F
65°F
76°F
74°F
72°F
78°F
68°F
65°F
70°F
65°F
76°F
78°F
72°F
78°F
WEEKDAY (5 DAY) WEEKEND (2 DAY)
Start
Time* Temperature Start Time* Temperature
1ST HEAT
2ND HEAT
3RD HEAT
4TH HEAT
1ST COOL
2ND COOL
3RD COOL
4TH COOL
Heating/Cooling Schedule Plan
Period
OPERATING FEATURES
Now that you are familiar with the thermostat buttons and
display, read the following information to learn about the many
features of the thermostat.
•SIMULTANEOUS HEATING/COOLING PROGRAM
STORAGE—Whenprogramming,youcanenterbothyour
heatingandcoolingprogramsatthesametime.Thereisno
need to reprogram the thermostat at the beginning of each
season.
•TEMPERATURE OVERRIDE — Press or until the
display shows the temperature you want. The thermostat
will override current programming and keep the room
temperature at the selected temperature until the next
program period begins. Then the thermostat will automati-
cally revert to the program.
•HOLD TEMPERATURE — The thermostat can hold any
temperaturewithinitsrangeforanindefiniteperiod,without
reverting to the programmed temperature. Press HOLD
TEMP button. HOLD will be displayed. Then choose the
desired hold temperature by pressing or . The
thermostat will hold the room temperature at the selected
setting until you press RUN PRGM button to start program
operation again.
•°F/°CCONVERTIBILITY—PressandholdSETTIMEand
HOLD TEMP buttons until the temperature display is in
Celsius (°C). To display Fahrenheit (°F), repeat the pro-
cess.
•12-HOUR/24-HOUR CLOCK DISPLAY — The clock isset
to display 12-hour time, which means that the clock will
display AM and PM time (12:00 AM is midnight; 12:00 PM is
noon). However, you may want to display a 24-hour clock
(military-styletime).The24-hourclockdisplaywillshow1:00
PMas13:00,2:00PMas14:00,andsoon.Tochangetothe
24-hour clock display, press and hold SET TIME and RUN
PRGMbuttons at the same time. In the24-hour clock mode,
AM and PM are not displayed.
•LOW BATTERY INDICATOR — If the 3 “AA” alkaline
batteries are low and should be replaced, the display will be
blankexceptforthewordBATTERY.Whenthebatteriesare
low,pressing any button will cause the displayto operate for
ten seconds. After ten seconds, the display will be blank
exceptforthewordBATTERY.Youcannotprogramwithlow
batteries, but you can override setpoint temperature.
•TEMPERATURE DISPLAY ADJUSTMENT — Your new
thermostathasbeenaccuratelysetinourfactory.However,
if you wish, you may adjust your new thermostat tempera-
ture display to match your old thermostat. This can be
accomplished (within a ±4°range) as follows:
1. Press VIEW PRGM and HOLD TEMP buttons at the
same time.
2. Press or to adjust the displayed temperature to
your desired setting.
3. PressRUNPRGMtoresumenormalprogramoperation.
PROGRAMMING YOUR THERMOSTAT
Nowyouarereadytoprogramyourthermostat.Thissectionwill
help you plan your thermostat’s program to meet your needs.
For maximum comfort and efficiency, keep the following guide-
lines in mind when planning your program.
• When heating (cooling) your building, program the tem-
peraturestobecooler(warmer)whenthebuildingisvacant
or during periods of low activity.
• During early morning hours, the need for cooling is usually
minimal.
• Programthethermostattoallowabout30minutestoreach
the desired temperature. (For example, if the first person
gets up at 6:00 AM, program the first period to begin at
5:30 AM.)
Look at the factory preprogrammed times and temperatures
shownbelow.Ifthisprogramwillsuityourneeds,simplypressthe
RUN PRGM button to begin running the factory preset program.
If you want to change the preprogrammed times and tempera-
tures, follow these steps.
Determine the time periods and heating and cooling tempera-
tures for your weekday and weekend programs. You must
program four periods for both the weekday and weekend pro-
gram. However, you may use the same heating and cooling
temperatures for consecutive time periods. You can choose
start times, heating temperatures, and cooling temperatures
Heating Program for
ALL days of the Week: Cooling Program for
ALL Days of the Week:
PERIOD TIME TEMP PERIOD TIME TEMP
1st
2nd
3rd
4th
6:00 AM
8:00 AM
5:00 PM
10:00 PM
68°F
68°F
68°F
64°F
1st
2nd
3rd
4th
6:00 AM
8:00 AM
5:00 PM
10:00 PM
78°F
82°F
78°F
78°F
FACTORY PREPROGRAMMING

independently for both weekday and weekend programs (for
example, you may select 5:00 AM and 70°as the weekday 1st
period heating start time and temperature, and also choose
7:00 AM and 76°as the weekday 1st period cooling start time
andtemperature).Usethetableatthebottomofthepagetoplan
your program time periods, and the temperatures you want
during each period. You may also want to look at the sample
program table to get an idea of how the thermostat can be
programmed.
Entering Your Program
Follow these steps to enter the heating and cooling programs
you have selected.
The thermostat should be programmed in the 12-hour format,
then switched to the 24-hour format, if desired (see OPERAT-
ING FEATURES for more information).
Set Current Time and Day
1. PressSETTIMEbuttononce.Thedisplaywillshowthehour
only.
EXAMPLE:
PM
2. Press and hold either or until you reach the correct
hour and AM/PM designation (AM begins at midnight; PM
begins at noon).
3. Press SET TIME once. The display window will show the
minutes only.
EXAMPLE:
4. Press and hold either or until you reach the correct
minutes.
5. Press SET TIME once. The display will show the day of the
week.
6. Press or until you reach the current day of the week.
7. Press RUN PRGM once. The display will show the correct
time and room temperature alternately.
Enter Heating Program
1. Ifyou want tochange thedisplay from Fahrenheitto Celsius
(or vice-versa), press SET TIME and HOLD TEMP at the
same time.
2. Move the SYSTEM switch to HEAT.
3. Press VIEW PRGM once. “MO TU WE TH FR” (indicating
weekdayprogram)willappearinthedisplay.Alsodisplayed
arethecurrentlyprogrammedstarttime for the1st heating
period and the currently programmed temperature (flash-
ing).
EXAMPLE:
AM
MO TU WE TH FR
This display window shows that for the 1st weekday period,
the start time is 6:00 AM, and 68°is the programmed
temperature(thisexamplereflectsfactorypreprogramming).
4. Press or tochangethedisplayedtemperaturetoyour
selected temperature for the 1st heating program period.
5. Press SET TIME once (the programmed time will flash).
Press or until your selected time appears. The time
will change in 15 minute increments. When your selected
time is displayed, press SET TIME again to return to the
change temperature mode.
6. Press VIEW PRGM once. The currently programmed start
time and setpoint temperature for the 2nd heating program
period will appear.
7. Repeat steps 4 and 5 to select the start time and heating
temperature for the 2nd heating program period.
8. Repeatsteps4through6forthe3rdand4thheatingprogram
periods. Weekday heating programs are now complete.
9. Press VIEW PRGM once. “SA SU” (indicating weekend
program) will appear in the display, along with the start time
for the 1st heating period and the currently programmed
temperature.
10.Repeat steps 4 through 8 to complete weekend heating
programming.
11.When you have completed entering your heating program,
press RUN PRGM.
Enter Cooling Program
If the outside temperature is below 50°F, disconnect
power to the cooling system before programming.
Energizing the air conditioner compressor during
cold weather may cause personal injury or property
damage.
1. Move SYSTEM switch to COOL position.
2. Follow the procedure for entering your heating program,
using your selected cooling times and temperatures.
CHECK YOUR PROGRAMMING
Follow these steps to check your thermostat programming one
final time before beginning thermostat operation.
1. Move SYSTEM switch to HEAT position.
2. Press VIEW PRGM to view the 1st weekday heating period
time and temperature. Each time you press VIEW PRGM,
the next heating period time and temperature will be dis-
played in sequence for weekday, then weekend program
periods(youmaychangeanytimeortemperatureduringthis
procedure).
3. Press RUN PRGM.
4. Move SYSTEM switch to COOL position.
5. Repeat step 2 to check cooling temperatures.
6. Press RUN PRGM to begin program operation.
YOUR THERMOSTAT IS NOW COMPLETELY PRO-
GRAMMED AND READY TO AUTOMATICALLY PROVIDE
MAXIMUM COMFORT AND EFFICIENCY!
CAUTION
!
NOTE