White Rodgers 1A65W User manual

WHITE-RODGERS DIVISION
EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO. 63123
[phone], Fax [phone]
9999 HWY. 48, MARKHAM, ONT. L3P 3J3
[phone], FAX [phone]
Printed in U.S.A.
PART NO. 37-5427C
Replaces 37-5427B
9520
INSTALLATION INSTRUCTIONS
1A65/1A65W
ELECTRIC-HEAT THERMOSTAT
(Single Pole)
FAILURETOREADANDFOLLOWALLINSTRUCTIONSCAREFULLYBEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.
WHITE-RODGERS
Operator: Save these instructions for future use!
DESCRIPTION
The Type 1A65/1A65W Electric Heat Thermostat is de-
signed for use on all types of electrical heating installa-
tionssuchascableheat,baseboards,wallinsertheaters,
etc. Its narrow operating differential and the ability of its
fully exposed knob to sense both radiant heat and room
air temperature make this control ideal for use on such
installations.
Dial Setting: Knob may be set anywhere between 40°
and85°Fbysimplyturningknobsothatindicatoronknob
points to the desired setting.
80
50
70
60
PRECAUTIONS
This control is a precision instrument, and should be
handled carefully. Rough handling or distorting compo-
nents could cause the control to malfunction. Take care
not to push or damage the knob sensing element
during installation.
To prevent electrical shock and/or equipment
damage,disconnectelectricpower tosystem,at
mainfuseorcircuitbreakerbox,untilinstallation
is complete.
All wiring must conform to local and national electrical
codes and ordinances.
Do not use on circuits exceeding specified volt-
ages. Higher voltages will damage control and
could cause shock or fire hazard.
Do not use on inductive loads. Inductive (motor)
loadswilldamagecontrolandcouldcauseshock
or fire hazard.
CAUTION
!
WARNING
!
SPECIFICATIONS
Switch Rating: Non-Inductive
22A (2500W) 120 VAC
22A (5000W) 240 VAC
18A (5000W) 277 VAC
Temperature Range: 40°to 85°F
Differential: 1°F
Switch Action: Open on rise
Contact Structure: SPST
INSTALLATION
If the heating equipment manufacturer has made provi-
sions or recommendations for the location of this control,
thenfollowthoseinstructions.Ifnot,thefollowingsugges-
tions should be observed.
1. The control should be mounted in the wall, approxi-
mately five feet from the floor, as near as possible to
the centre of the controlled area.
2. It should be mounted on a partitioning wall, not on an
outside wall.
3. Itshouldbemountedasfaraspossiblefromundesir-
able sources of heat and cold such as:
a. Windows and doors
b. Direct rays from sun
c. Hot water or cold water pipes
d. Adjoining outside walls

WIRING
CAUTION
!
Thermostat
Mounting Screw
Mounting Screw
Cover
BLUE
BLACK
LINE LOAD
50
60
70
80
Note: Do not
push on this knob
because calibration
will be changed
if knob is bent.
All wiring must conform to local and national electrical codes and ordinances.
The thermostat may be mounted in any standard 2” x 3”
electrical outlet box. For ease of installation use a deep
type box.
USE WITH COPPER CONDUCTORS ONLY.
1. Make electrical connection to thermostat leads with
wire nuts or other local code approved devices. All
connections must be tight.
2. Pushthelead wiresintothe outletboxand mountthe
thermostat to the outlet box with screws provided.
Take care not to push or damage the knob sens-
ing element during installation.
3. Snap on the thermostat cover and turn knob to
desired setting.